Ricoh A027 Modification Bulletin FT2260
MODIFICATION BULLETIN NO. 32 Page 1 of 3 ISSUED ON: November 15, ’90
Model M210 Volt/Hz
Modified Article AC Drive Board
Reason for
To absorb electrical noise
Modification
Draw
No.
Old Parts
No.
A0275560 A0275565 AC Drive Board - 115V 1 - 1 X/O 17 13
A0275660 A0275665 AC Drive Board - 220/240V 1 - 1 X/O 17 13
New Parts
No.
16020908 Noise Killer 0 - 3 #149 37
Description
Date of
Modification
A.B.C. Q’ty Used
Old →
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
#: New Index
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhall.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to
install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used
in the old machine. x = Not interchangeable o = Interchangeable
MODIFICATION BULLETIN NO. 32 Page 2 of 3 ISSUED ON: November 15, ’90
DETAILS OF MODIFICATION
As a temperary countermeasure against electrical noise caused by counter-electromotive force from th e main and exhaust
motors, two ferrite cores were placed on the ac harnesses at the factory. (For the details, please r efer to MB #31 and RTB #4.)
As a permanent countermeasure, three noise killers (CR402 to 404) are now being added to the ac driv e board circuit as
shown below. (the ferrite cores are removed from the ac harnesses when the noise killers are added.) .
NOTE: The ferrite core (16070478) is still registered as a service part to correct this problem in the fi eld.
AC Drive Board (PCB)
Exposure Lamp
Drive Circuit
CN401-3
CN401-2
CN401-1
S/M Page 1-23
RA401-1
CR402
CR404
RA401-2
CR403
RA402
CN406-1
CN406-2
CN402-2
CN403-3
CN403-2
CN403-1
CN402-1
CN405-1
CN405-2
Page 33
Thermoswitch
Exposure Lamp
Exhaust Blower
CR
Symbol
No.
CR401
(115V)
(220V)
CR402
CR403
CR404
Index
No.
121
122
149
149
149
CR402 to 404 (#16020908) have
been added to the ac drive board.
M
M
Main Motor
Anti-condensation
Heater (Optics)
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 32 Page 3 of 3 ISSUED ON: November 15, ’90
MODEL NAME
Savin 7150 115/60 USA, Canada A027-15 7001007861
Nashua 8115 115/60 Canada, L.America A027-16 1310100001
Ricoh FT2260 115/60 USA, Canada A027-17 2140090049
Ricoh FT2260 110/60 Taiwan A027-19 2140100642
Nashua 8115 220,240/50 Europe, etc. A027-25 1300090001 A027-45
infotec 9115Z 220,240/50 Europe A027-26 376100XXXX A027-46
Ricoh FT2260 220,240/50 Europe, etc. A027-27 2140090821 A027-47
Ricoh FT2260 220,240/60 Phillipines, etc. A027-28 2140090936
Ricoh FT2260 220,240/50 Asia A027-29 2140091056
aurora AC2502 110/60 Taiwan A027-99 0020100001
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
MODIFICATION BULLETIN NO. 33 Page 1 of 1 ISSUED ON: November 15, ’90
Model M210 Volt/Hz
Modified Article Platen Cover
Reason for
Parts Standardization
Modification
To standardize the parts, the following changes have been made.
Old and new parts are completely interchangeable.
Item No. Old Part Number New Part Number Description Index No. Page
A0271361 A0541881 Platen Cover - Ricoh 29 3
1
A0276392 A0546396 Platen Cover - Savin/Nashua 29 3
A0276792 A0546196 Platen Cover - Hoechst 29 3
Date of
Modification
Serial Number
A0271378 A0541885 Platen Cover Pedestal - Ricoh 17 3
2
A0276428 A0546734 Platen Cover Pedestal - Savin 17 3
A0276628 A0546333 Platen Cover Pedestal - Nashua 17 3
A0276728 A0546133 Platen Cover Pedestal - Hoechest 17 3
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 33 Page 1 of 1 ISSUED ON: January 31, ’91
Model M210 Volt/Hz
Modified Article Bracket - Center Fence Lever
Reason for
Parts Catalog Correction
Modification
The part number and description of index no. 23 are missing from the
parts catalog. Please correct your catalog as follows:
Part Number Description Index No. Page No.
52202704
Bracket - Center Fence
Lever
23 11
Date of
Modification
Serial Number
T.Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 35 Page 1 of 3 ISSUED ON: March 31, ’91
Model M210 Volt/Hz
Modified Article Main Board
Reason for
To reduce the erratic malfunction when replacing the main board
Modification
Draw
No.
Old Parts
No.
A0275105 Main Board 1 - 0 2 13
New Parts
A0279502 Main Board Kit 0 - 1 X/O 2 13
No.
Description
Date of
Modification
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old → New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts tim f overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to
install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used
in the old machine. x = Not interchangeable o = Interchangeable
MODIFICATION BULLETIN NO. 35 Page 2 of 3 ISSUED ON: March 31, ’91
DETAILS OF MODIFICATION
To prevent erratic malfunction, the ac drive board has been modified. For the details, please refer to MB
#32. The erratic malfunction may occur when the main board is replaced on a machine that does not ha ve
the modified ac drive board. To reduce the chance of erratic malfunction, the following main board k it has
been registered as a service part.
Main Board Kit (#A0279502)
1. Main Board 1 pc (#A0275105)
2. Ferrite Core 2 pcs (#16070478)
3. Ferrite Core Installation Procedure 1 sheet
For the details, please refer to RTB #4 issued on July 15, 1990.
T.Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 35 Page 3 of 3 ISSUED ON: March 31, ’91
MODEL NAME
Savin 7150 115/60 USA, Canada A027-15
Nashua 8115 115/60 Canada, L.America A027-16
Ricoh FT2260 115/60 USA, Canada A027-17
Ricoh FT2260 110/60 Taiwan A027-19
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Nashua 8115 220,240/50 Europe. etc. A027-25 A027-45
infotec 9115Z 220,240/50 Europe A027-26 A027-46
Ricoh FT2260 220,240/50 Europe, etc. A027-27 A027-47
Ricoh FT2260 220,240/60 Philippines, etc. A027-28
Ricoh FT2260 220,240/50 Asia A027-29
aurora AC2502 110/60 Taiwan A027-99
MODIFICATION BULLETIN NO. 36 Page 1 of 2 ISSUED ON:June 30, ’91
Model M210 Volt/Hz
Modified Article Bottom Plate, etc.
Reason for
Parts Standardization
Modification
Due to parts standardization, the following parts have been changed.
Old P/N New P/N Description interchangeability Page Index
A0082710 A0302910 Bottom Plate O/O 19 9
52152713 AF013012 Bottom Plate Pad O/O 19 10
Date of
Modification
Serial Number
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 36 Page 2 of 2 ISSUED ON:June 30, ’91
MODEL NAME V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
Savin 7150 115/60 USA, Canada A027-15 701060XXXX
Nashua 8115 115/60 Canada, L.America A027-16 1311040001
Ricoh FT2260 115/60 USA, Canada A027-17 2141030001
Ricoh FT2260 110/60 Taiwan A027-19 2141040223
Nashua 8115 220,240/50 Europe. etc. A027-25 1301030133 A027-45
infotec 9115Z 220,240/50 Europe A027-26 A027-46
Ricoh FT2260 220,240/50 Europe, etc. A027-27 2141040513 A027-47
Ricoh FT2260 220,240/60 Philippines, etc. A027-28 2141041063
Ricoh FT2260 220,240/50 Asia A027-29 2141041263
aurora AC2502 110/60 Taiwan A027-99 0021030001
JAPAN PRODUCTION RIF PRODUCTION
MODIFICATION BULLETIN NO. 37 Page 1 of 4 ISSUED ON: September 30, ’91
Model M210 Volt/Hz
Mod i fied Article Paper Feed
Reason for
T o prevent paper jams
Modification
Draw
No.
Old Parts
No.
52202580 A0270146 Support Plate - Feed Drive 1 → 1 X/O 39 27
52162741 A0270147 Bracket - Paper Feed Solenoid 1 → 1 X/O 38 27
52162818 52162793 Pad Holder 1 → 1 X/O 37 19
New Parts
No.
Description
Date of
Modification
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old → New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Numbe r
Rank: A : Repla ce with new parts immedi ately. B : Repl ace with ne w parts at time of repair. C : Replace with new parts at time of overhaul.
Interchangeability:
(1) W hen old and new parts are not mutually interchangeable, use additional parts or an as sembly part as indicated in "Parts needed for replacement by new part" to
install the ne w pa rt.
(2) The mark to the left of the sl ash indicates whethe r the old part can be used in the ne w ma chine, and the mark to the right indicates whethe r the new part can be used
in the old machine. x = Not interchangeable o = Inte rchangeable
MODIFICATION BULLETIN NO. 37 Page 2 of 4 ISSUED ON: September 30, ’91
DETAILS OF MODIFICATION
With the old pad holder, the leading edge of the paper might enter the gap between the cassette bottom plate and the pad holder, as
in the figure below. This causes a paper jam. To prevent this problem, the shape of the pad holder tip has been changed in order to
decrease the gap, and as a result it will h elp the paper feed in more smoothly.
The shape of the pad
Paper feed roller
ho lder tip has been
changed.
Cassette
Pad hol der
This gap is wider
Pad holder
Old
Pad holder
New
Bracket - paper feed sol.
* Adjustable
Hole for relay
feed solenoid
* Adjustable
Hole for cassette
feed solenoid
MODIFICATION BULLETIN NO. 37 Page 3 of 4 ISSUED ON: September 30, ’91
DETAILS OF MODIFICATION
At the same time, for better adjustment of the solenoid stroke on the tray feed, relay feed, and cassette feed solenoids, the bracket
holes marked * have been changed as follows.
* Adjustable
Hole for tray
* Fix ed Hole
feed solenoid
* Fixed Hol e
* Fixed Hole
Support bracket - feed drive Support bracket - feed drive
Old
New
Bracket - paper feed sol.
Old
New
T. Ito, Manager
Copier Technical Support
Loading...