Rice Lake Weighing Systems 882IS Operating Manual

Download

Page 1

882IS/882IS Plus

Intrinsically Safe Indicator/Controller

Version 1.0

Technical Manual

PN 183532 Rev BAugust 20, 2019

Page 2

An ISO 9001 registered company

Rice Lake Weighing Systems

is a registered trademark of

Rice Lake Weighing Systems.

All other brand or product names within this publication are trademarks or

registered trademarks of their respective companies.

All information contained within this publication is, to the best of our knowledge, complete and

accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make

changes to the technology, features, specifications and design of the equipment without notice.

The most current version of this publication, software, firmware and all other product

updates can be found on our website:

www.ricelake.com

Page 3

Contents

Technical training seminars are available through Rice Lake Weighing Systems. Course descriptions and dates can be viewed at www.ricelake.com/training or obtained by calling 715-234-9171 and asking for the training department.

Contents

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.4 FM Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.5 Hazardous Location Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.6 Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.7 Front Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.8 General Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.9 Indicator Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.9.1 Toggle Gross/Net Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.9.2 Toggle Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.9.3 Zero Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.9.4 Acquire Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.9.5 Remove Tare Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.9.6 Preset Tare (Keyed Tare) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.9.7 Print Ticket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.9.8 Front Panel User Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.9.9 Displaying Audit Trail Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.9.10 Display Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.9.11 Clear the Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.9.12 Display Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1 Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2 Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.3 Hazardous Area Installation of the 882IS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.4 Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.4.1 Backplate Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.5 Cable Connections on the 882IS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.5.1 Power Supply to Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.5.2 AC Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.5.3 Battery Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.5.4 Load Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.5.5 Cable Shield Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.5.6 882IS Enclosure Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.5.7 CPU Board Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.5.8 Serial Communications – Port 1 (COM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.6 CPU Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.7 Audit Trail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.8 Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.9 Backplate Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.10 Legal for Trade Sealing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.11 IO Module Option Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.12 Rechargeable Battery Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.13 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.0 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.1 Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Page 4

882IS/882IS Plus

Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars

3.2 User Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.2.1 Audit Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.2.2 Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.2.3 Scale Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.2.4 Scale Format Menu - if Split = Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.2.5 Scale Format Menu - if split = 2 RNG, 3 RNG, 2 INTVL, 3 INTVL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.2.6 Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.2.7 Features Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.2.8 Region Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.2.9 Region - Regulation - Indust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3.2.10 Keylock Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.2.11 Setup Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.2.12 Ports - Serial Ports Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.2.13 Ports - Fiber Optics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.2.14 Print Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.2.15 Digital Inputs Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

3.2.16 IO Module Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3.2.17 Power Savings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3.2.18 Version Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3.3 Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.4 Time and Date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.5 Accumulator Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.6 Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

4.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4.1 Front Panel Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4.1.1 Five-Point Linearization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4.1.2 Rezero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4.2 Last Zero. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4.3 Temporary Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4.4 Adjusting Final Calibration (Trimming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4.5 Gravity Compensation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4.6 EDP Command Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4.7 Revolution® Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

5.0 Using Revolution®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

5.1 Communication With the Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

5.2 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.2.1 New Configuration File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.2.2 Open an Existing Configuration File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.2.3 Saving a Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.3 Revolution Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

6.0 EDP Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.1 The EDP Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.1.1 Key Press Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.1.2 Reporting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6.1.3 The RESETCONFIGURATION Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6.1.4 Parameter Setting Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6.1.5 Scales Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

6.1.6 Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

6.1.7 Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

ii Visit our website www.RiceLake.com

Page 5

Contents

6.1.8 Ports COM Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

6.1.9 Stream Tokens Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

6.1.10 Feature Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

6.1.11 Regulatory Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

6.1.12 Passwords Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.1.13 Keypad Lock Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.1.14 Print Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.1.15 Digital I/O Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.1.16 Weigh Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

6.1.17 Power Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.1.18 Setup Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.1.19 Analog Output Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.1.20 Analog Output Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

6.1.21 Test Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

7.0 Print Formatting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

7.1 Print Formatting Tokens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

7.2 Default Print Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

7.3 Customizing Print Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.3.1 Using the EDP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.3.2 Using the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.3.3 Using Revolution® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

8.0 IO Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

8.1 IO Module Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

8.1.1 AC Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

8.1.2 RS-232/RS-422 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

8.2 USB Device Communications – Port 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

8.3 Ethernet Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

9.0 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.1 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.1.1 Displayed Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.2 Using the HARDWARE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

9.3 ERROR Commands Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

9.4 Status Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

9.5 TARE and ZERO Key Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

9.6 Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

9.6.1 Stream Serial Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

9.6.2 Print Output Serial Data Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

9.7 Custom Stream Formatting – Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

9.8 Stream Formatting Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

9.8.1 Toledo 8142 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

9.8.2 Cardinal 738 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

9.8.3 Weightronix WI 120 Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

9.9 ASCII Character Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

9.10 Digital Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

9.10.1 Sample Rate: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

9.10.2 Digital Filter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

9.11 Analog Output Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Page 6

882IS/882IS Plus

Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars

10.0 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

11.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

iv Visit our website www.RiceLake.com

Page 7

Introduction

1.0 Introduction

This manual provides information on installation, configuration, calibration and servicing of the 882IS and 882IS Plus indicator. The installer should be familiar with requirements for installation of equipment in hazardous areas. Refer to the 882IS Conditions of Use in Hazardous Locations document, PN 191698, for the intrinsic safety certification and classification, specific conditions of use and system limitations and restrictions for the 882IS.

Configuration and calibration of the indicator can be accomplished using the indicator front panel keys, the EDP command set or Revolution

1.1 Overview

The standard 882IS unit is equipped with a tilt stand base for tabletop or wall mounting applications and the 882IS Plus additionally is equipped with a numeric keypad.

Standard Features include:

• Drives up to four x 350or eight x 700 load cells

• Seven-digit, seven-segment LCD display with 121 x 24 dot matrix messaging area and white LED backlight

• Stainless steel NEMA IP66 enclosure

• Numeric keypad (882IS Plus only)

• Two configurable digital inputs

• Semi-automatic (push button) zero setting and (push button) tare

• Automatic zero tracking

• Gross/Net display

• Unit switching (lb, oz, kg, g, T, t)

• Power saving features

• Remote printer capability

• RS-422

• Duplex fiber-optic port allowing for electrically-isolated communication with the IO module

configuration utility. See Section 3.0 on page 23 for information about configuration methods.

Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.RiceLake.com

Warranty information can be found on the website at www.ricelake.com/warranties

• Ethernet TCP/IP interface for 10Base-T/100Base-TX network communications

• USB interface device

• Expansion slot for one option card

• RS-232/RS-422

1.2 Options

Options for the 882IS are listed below.

Part Number Description

180831 Battery option, IS6V2 194191 Battery charger, IS6V2, 100-240 VAC NEMA 5-15, North American plug 194189 Battery charger, IS6V2, 100-240 VAC, EU plug 194192 Battery charger, IS6V2, 100-240 VAC, UK plug 180837 Power supply, 882IS mb-EPS-100-240-X2 VAC, dual output 6.8 VDC 200 mA 195109 Power supply, 882IS mb-EPS-100-240-X2 VAC, dual output 6.8 VDC 200 mA, 1/2in NPT-M20 179668 Cable, M12 power 22 inch hazardous location (for battery version) 179669 Cable, M12 power 10 foot hazardous location 179670 Cable, M12 power 50 foot hazardous location 179671 Cable, M12 power 100 foot hazardous location 179678 Tilt stand, 882IS battery option 163751 Tilt stand, 882IS 177709 882IS IO module 78026 Fiber optic, duplex cable 100 ft 78027 Fiber optic, duplex cable 200 ft

Table 1-1. 882IS Options

Page 8

882IS/882IS Plus

DANGER

WARNING

CAUTION

IMPORTANT

WARNING

1.3 Safety

Safety Signal Definitions:

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.

Indicates information about procedures that, if not observed, could result in damage to equipment or corruption to and loss of data.

Do not operate or work on this equipment unless this manual has been read and all instructions are understood. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake Weighing Systems dealer for replacement manuals.

General Safety

Failure to heed could result in serious injury or death.

Some procedures described in this manual require work inside the indicator enclosure. These procedures are to be performed by qualified service personnel only.

Do not allow minors (children) or inexperienced persons to operate this unit.

Do not operate without the enclosure completely assembled.

Do not use for purposes other than weight taking.

Do not place fingers into slots or possible pinch points.

Do not use this product if any of the components are cracked.

Do not exceed the rated specification of the unit, see Section 6 on page 80.

Do not make alterations or modifications to the unit.

Do not remove or obscure warning labels.

Do not submerge.

2 Visit our website www.RiceLake.com

Page 9

Introduction

1.4 FM Approval

The 882IS is a FM Entity approved for:

• Classes I, II and III

• Division 1

• Groups A, B, C, D, E, F and G

• Class I, Zone 0, AEx/EX ia IIC

• Zone 0/20

• Zone 20 AEx ia IIIC

• IP66

• T-rating T4 =

Only devices that have FM Entity Approval with proper entity parameters may be used unless specifically listed in this manual or control drawings, PN 77412, 180848 and 182301, as part of the Rice Lake Weighing System’s FM systems approval. Failure to comply with this voids the FM approval.

This classification of hazardous materials are different in the US and European standards, because of this, the safety class of the 882IS is declared in the US standards: Class I, II, III, DIV1 and Groups A-G.

Substitution of components may impair intrinsic safety. To prevent ignition of flammable or combustible atmospheres, disconnect power before servicing. Disconnect all power to this unit before installing, servicing or cleaning. Failure to do so could result in bodily harm and/or

property damage. The 882IS indicator has been certified by UL (U.S., Canada, ATEX and IECEx) with a temperature rating of 14°F to 104°F

(-10°C to 40°C) for use in hazardous environments where the auto ignition temperature of the hazardous material is below the rating.

Do not install, disconnect or perform any service on this equipment before power has been switched off or the area has been secured as non-hazardous by personnel authorized to do so by the responsible person on-site.

14°F to 104°F (-10°C to 40°C)

Page 10

882IS/882IS Plus

1.5 Hazardous Location Labels

The following labels will be affixed to the 882IS and 882IS Plus indicators.

Figure 1-1. 882IS and 882IS Plus Indicator Label

Figure 1-2. IS6V2 Battery Label

Figure 1-3. mb-EPS-100-240-X2 Power Supply Label

4 Visit our website www.RiceLake.com

Page 11

Introduction

IMPORTANT

1.6 Operating Modes

The three modes of operation for the 882IS are described below.

Weigh Mode

In this mode, the indicator displays gross or net weights to indicate the type of weight value displayed, and annunciators to indicate scale status.

Setup Mode

Most of the procedures described in this manual, including setup and calibration, require the indicator to be in setup mode. To enter setup mode, remove the fillister head screw from the bottom of the enclosure. Insert a non-conductive tool into the access hole and press the setup switch once. the indicator display changes to show the word Scale.

Breaking the seal to enter the configuration mode will void a Legal for Trade unit.

The 882IS also has an Audit Trail that can track changes to setup and calibration, allowing the setup switch to be bypassed with Jumper JP4 on the CPU board. If Audit Trail is enabled, setup mode can then be accessed through the user setup mode.

User Setup Mode

User setup mode (accessed by pressing the Menu key) is used to:

• View the audit trail, set time & date

• View or clear the accumulator value

• View the current tare value

• Enter setup/configuration mode (if audit trail is enabled)

Page 12

882IS/882IS Plus

882IS

PTTHOLDPEAK PC SAMPLE %

ZERO

TARE

UNITS

GROSS

NET

B/N

POWER

START

STOP

ZERO

GROSS

NET

B/N

TAR E

POWER

1.7 Front Panel Display

Figure 1-4 shows the 882IS Plus front panel display and Table 1-2 describes the key functions.

The numeric or weight portion of the display consists of the seven-segmented LCD digits and below that, is a messaging area of the display which is the dot matrix and can display two-line non-configurable messages (ie: error messages).

The symbols on the keys in Figure 1-4 (representing up, down, enter, left, right) describe the key functions when in configuration/setup mode. The keys are used to navigate through menus, select digits within numeric values, and increment/ decrement values. See Section 3.2 on page 24 for information about using the front panel keys in configuration mode.

Figure 1-4. 882IS Plus Front Panel Display

Key Function

The Zero key sets the current gross weight to zero Also used as the up key to navigate menus

The

Print key sends an on-demand print format out a communications port, provided the conditions for standstill are met. If enabled in

configuration, Also used as the right key to navigate menus or to select another digit when editing a value The

Gross/Net key toggles the weight display between gross and net mode. If a tare value has been entered or acquired, the net

value is the gross weight minus the tare. Gross mode is shown by the annunciator. Also used as the down key to navigate menus

The

Menu key allows access the user setup menu. This key also acts as the cancel key when editing parameter values, or as an exit

key when in the configuration or user setup menus

The

Units key switches the weight display to an alternate unit, defined in the format menu, see Figure 3-6 on page 27. Units Available:

lb, kg, oz, metric ton, ton, gram Also used to navigate to different menus or to toggle to another digit when editing a value

The

Tare key performs one of several predetermined Tare functions dependent on the mode of operation selected in the Tare

Function

The

Power key turns the unit on or off. Press and hold to turn on, press momentarily to turn off.

Print may display while the unit prints

Gross/Brutto annunciator; net mode is shown by the Net

parameter. This key also acts as enter for numeric or parameter entry.

Table 1-2. 882IS Key Functions

6 Visit our website www.RiceLake.com

Page 13

Key Function

START

STOP

Future enhancement

Clear key clears the current value during a numeric entry (available in the 882IS Plus)

The

Decimal Point key inserts a decimal point where necessary (available in the 882IS Plus)

The

The numeric keypad can be used to enter values (available in the 882IS Plus)

Table 1-2. 882IS Key Functions

Introduction

Annunciator Function

Gross/Brutto Gross or Brutto weight mode Net Net weight mode

Center of Zero - Indicates that the current gross weight reading is within +/- 0.25 display divisions of the acquired zero, or is within the center of zero band. A display division is a resolution of the displayed weight value, or the smallest incremental increase or decrease that can be displayed or printed.

Standstill - The scale is at a standstill or within the specified motion band. Some operations including zero, tare and printing can only be done when the standstill LCD is on.

Peak Hold Future enhancement T Indicates that a tare has been acquired and stored by the system PT Indicates that a preset tare weight has been keyed in or entered via the EDP command PC Future enhancement Sample Future enhancement % Future enhancement

Table 1-3. Annunciator Functions

Page 14

882IS/882IS Plus

UNITS

ZERO

GROSS

NET

B/N

TAR E

UNITS

GROSS

NET

B/N

TAR E

GROSS

NET

B/N

Note

UNITS

ZERO

Note

TAR E

1.8 General Navigation

The front panel keys are used to navigate through the menus in configuration mode (see Section 3.0 on page 23).

• and move left and right (horizontally) in a menu level

• and move up and down (vertically) to different menu levels

• serves as an enter key for selecting parameter values within the menus

Press

or to scroll left or right until the desired menu group appears on the display. Press to move

down to the sub-menu or parameter to be edited. When moving through the menu parameters, the current selected value appears first on the display.

Edit Parameter Values

To change a parameter value, scroll left or right to view the values for that parameter. When the desired value appears on the display, press to select the value and move back up one level. To edit numerical values, use the navigation keys to select the digit and to increment or decrement the value. Alternatively, use the numeric keypad (882IS Plus), to enter the digits.

The decimal point will begin flashing if a decimal value is allowed. Use the navigation keys, to move the decimal point left or right. Press when done.

1.9 Indicator Operations

Basic 882IS operations are summarized below.

1.9.1 Toggle Gross/Net Mode

Press to toggle the display mode between gross and net.

Net mode is available when a tare value has been entered or acquired (Net = Gross minus Tare). If a tare has not been entered or acquired, the display remains in gross mode. The B (Brutto), G (Gross) or NET icons on the LCD indicate the current mode.

1.9.2 Toggle Units

Press to switch between primary and secondary units. The current units are displayed on the LCD.

1.9.3 Zero Scale

1. In gross mode, remove all weight from the scale and wait for to display.

2. Press . displays and indicates the scale is zeroed.

The scale must be stable and within the configured zero range for the scale to be zeroed. If the scale cannot be zeroed, No zero will display.

1.9.4 Acquire Tare

1. Place a container on the scale and wait for to display.

2. Press to acquire the tare weight of the container. The Net weight is displayed and the T annunciator displays to show the tare value is entered.

8 Visit our website www.RiceLake.com

Page 15

Introduction

ZERO

TAR E

ZERO

Note

TAR E

Note

TAR E

Note

1.9.5 Remove Tare Value

1. Remove all weight from the scale and wait for . The display reads .

2. Press to zero the scale if needed.

3. Press (or in OIML mode). The display shifts to gross weight and the Gross icon is lit.

If keyed tares are allowed, press to open the keyed tare prompt. To clear the tare, press again.

1.9.6 Preset Tare (Keyed Tare)

Tare mode must be set to keyed or both for the preset tare feature to function.

1. With the scale empty and zero weight on the display, press . One flashing 0 displays with the focused digit flashing.

2. Key in the value using the keypad on the 882IS Plus (see Section 1.9 on page 8).

• Press or to select the digit

• Press or to increment or decrement the value

• Press to move to the decimal point entry

• Press or to adjust the decimal point placement

• Press when the value is correct

The display will change to the Net mode and PT lights to show the preset tare was entered.

Entering a keyed tare of zero will remove the stored tare value.

1.9.7 Print Ticket

1. Wait for to light.

2. Press to send data to the configured communications port.

1.9.8 Front Panel User Setup

Press to enter user setup mode. Use user setup mode to:

• View audit trail information

• Enter configuration mode if audit trail is enabled

• View or clear the accumulator

• View the current tare value

• Time and date

• Test menu

1.9.9 Displaying Audit Trail Information

The Audit Trail Configuration and Calibration counters can be viewed in user setup mode.

1. Press . Audit displays.

2. Press to display the Legally Relevant Firmware version.

3. Press to display Calibration.

Page 16

882IS/882IS Plus

Note

TAR E

4. Press to view the Calibration Counter.

5. Press to return to Calibration.

6. Press to display Configuration.

7. Press to view the Configuration Counter.

8. Press to return to Configuration.

9. Press to return to the weigh mode.

1.9.10 Display Accumulator

Enable the accumulator before use in weigh mode. Once enabled, weight (net weight if a tare is in the system) is accumulated whenever a print operation is performed using the Print key, digital input, or KPRINT EDP command. The scale must return to below the threshold value before the next accumulation.

1. Press to enter the user setup mode, Audit is displayed.

2. Press or until Accumulator is displayed.

Accumulator

performs one accumulation, and only if the weight is above the accumulator threshold. Weight must return to below the accumulator threshold value before another accumulation is allowed.

The EDP command SC.THRESH#n is configured in the setup menu. See Section 3.2.3 on page 25.

3. Press . View is displayed.

4. Press to view the current accumulator value.

is only displayed if the accumulator is enabled. See Section 3.2.3 on page 25. The Print operation only

5. While the accumulator value is displayed, press to print the value.

6. Press to return to the weigh mode.

1.9.11 Clear the Accumulator

1. Press to enter the user setup mode. Audit is displayed.

2. Press or until Accumulator is displayed.

3. Press , then press or until Clear Accumulator is displayed.

4. Press to clear the accumulator. Clear will display briefly and display returns to Clear Accumulator.

5. Press to return to the weigh mode.

1.9.12 Display Tare

When a tare value is displayed, the Gross and Net icons will be off and is lit. To display a tare:

1. Press .

2. Press to Tare and press to view the current tare value.

3. Press twice to return to weigh mode.

If there is not a tare in the system, the value displayed is zero and the Gross and Net icons are turned off.

10 Visit our website www.RiceLake.com

Page 17

Installation

WARNING

IMPORTANT

2.0 Installation

This section describes procedures for connecting power, load cells, digital inputs and data communications cables to the 882IS indicator.

* Use anti-static protection for grounding and to protect components from electrostatic discharge (ESD) when

working inside the indicator enclosure.

* Procedures requiring work inside the indicator must be performed by qualified service personnel only.

* Disconnect the indicator from power source before opening enclosure.

* Component level repair, excluding board-swapping, is not permitted on FM Approved equipment by anyone other

than the manufacturer. It is mandatory to return 882IS to Rice Lake Weighing Systems for repairs.

* The entire indicator must be shipped back to Rice Lake Weighing Systems for repair. Please contact a local dealer or

Rice Lake Weighing Systems to obtain a return material authorization (RMA). There are no user serviceable parts within the 882IS except CPU board replacement. All repairs are to be performed by qualified service personnel only.

2.1 Unpacking and Assembly

Immediately after unpacking, visually inspect the 882IS to ensure all components are included and undamaged. The shipping carton should contain the indicator and manual. If any parts were damaged in shipment, notify Rice Lake Weighing Systems and the shipper immediately.

Page 18

882IS/882IS Plus

2.2 Product Dimensions

Figure 2-1. 882IS Product Dimensions (universal and optional battery versions shown)

Dimensions Without Battery

A 8.94 inch (227.1 mm) B 7.66 inch (194.6 mm) C 6.50 inch (165.1 mm) D 8.10 inch (205.7 mm) E 9.96 inch (253 mm) F 4.36 inch (110.7 mm) G 8.37 inch (212.6 mm)

Dimensions with Optional Battery and Tilt Stand

H 4.64 inch (117.9 mm)

I 5.00 inch (127 mm)

J 9.03 inch (229.4 mm) K 10.29 inch (261.4 mm) L 130.06 inch (331.7 mm)

Table 2-1. 882IS Product Dimensions

12 Visit our website www.RiceLake.com

Page 19

Installation

Non-Classied

Area

Classied Area

Fiber Optic

VDC

115/250 VAC

AC Power Supply (Intrinsically Safe

Output) Entity

Approved

Battery (optional)

Entity Approved

I/O Module

(optional)

Battery

Charger

(optional)

Junction

Box

(optional)

Load cells approved

for hazardous environments

(Up to 4 x 350Ω

or 8 x 700Ω)

Note

2.3 Hazardous Area Installation of the 882IS

The following information is provided to help the installer with the correct installation of the 882IS system. See the following diagram of a typical intrinsically safe system.

2.4 Mounting Instructions

The 882IS includes a universal mount. The universal mount can be mounted on a wall, tabletop or any flat surface.

Reattach the 882IS to the universal mount.

Figure 2-2. Intrinsically Safe System Diagram Example

The universal mount comes attached to the 882IS. Rice Lake Weighing Systems recommends removing the 882IS from the universal mount prior to mounting.

Figure 2-3. Mounting the 882IS

1. Using the mount as a template, mark the screw locations.

2. Drill holes for the screws.

3. Secure the universal mount using the appropriate length 1/4'' or M6 hardware (not included).

Page 20

882IS/882IS Plus

WARNING

2.4.1 Backplate Removal

Remove the backplate of the universal mount assembly to gain access to the inside of the enclosure and CPU board.

Backplate

Backplate Nuts

Figure 2-4. Remove Enclosure Backplate

4. Remove the eight nuts that attach the backplate to the enclosure.

5. Remove the backplate.

Disconnect power to the indicator prior to removing the backplate.

2.5 Cable Connections on the 882IS

The 882IS has four cord grips at the bottom of the enclosure for cabling into the enclosure. One stainless steel cord grip is used for the power supply and other cord grips are for the load cell cable, communications and the fiber optic cable. Two of the four cord grips come with a plug installed to prevent moisture from entering the enclosure. Depending on the application, remove the plug from the cord grip that will be used and install cables as required. Figure 2-5 shows the recommended 882IS cord grip assignments.

To power supply

Load cell cable cord grip

Communications cable cord grip

Setup switch access screw

Fiber optic cord grip

Figure 2-5. Recommended Cord Grip Assignments

14 Visit our website www.RiceLake.com

Page 21

Installation

WARNING

Note

2.5.1 Power Supply to Indicator

Do not under any circumstances, connect or disconnect the DC wire from the indicator while the AC power is applied to the power supply. This will cause the power supply fuse to blow.

The 882IS must be powered by an FM-approved Rice Lake power supply or optional battery. The power requirements of the 882IS indicator are as follows:

• Minimum input voltage - 5.8 VDC

• Maximum input voltage - 7.9 VDC

• Peak current consumption - .25 W

• Average input current (with four load cells) 100-175 mA

The DC power cable should be attached to connector J3 (Figure 2-11 on page 19).

2.5.2 AC Power Wiring

Units are powered by an FM-approved power supply. 100-240 VAC into Rice Lake Weighing Systems’ mb-EPS-100-240-X2 intrinsically safe power supply (PN 180837) is recommended. See the mb-EPS-100-240-X2 Power Supply Instruction sheet (PN 194894) for information on wiring and power specifications.

2.5.3 Battery Option

The optional IS6V2 battery (PN 180831) provides an intrinsically safe battery that can replace the power supply. The battery is approved for use in hazardous environments. A low battery error message displays on the 882IS to indicate that the battery needs to be recharged. Charge the battery a minimum of 12 hours. A yellow indicator light on the battery charger will remain on (in high current charging mode), until the battery is charged at about 70%, at which point the charger switches to a float charge mode and the LED turns off.

To keep the battery at full capacity, it is recommended to leave the battery connected to the charger, in float charge mode, until ready to use. The battery can remain on the charger in float charge mode indefinitely without damaging the battery. See IS6V2 Battery Charging Instruction sheet (PN 194893) for instructions on charging the battery.

Load Cell Size Quantity of Cells Estimated Operating Time

350 Ohm Load Cell

700 Ohm Load Cell

Table 2-2. Estimated Battery Operating Times

While connected to the DC battery pack with the indicator off, the 882IS still draws a small amount of current that will shorten battery run time. To preserve battery life, disconnect the battery when not in use.

1 80 - 95 hours 4 60 - 80 hours 1 85 - 100 hours 4 70 - 90 hours

Page 22

882IS/882IS Plus

Note

Silver

side out

Shield wire

Cut insulated jacket here for foil shielded cables

Length of foil before folding back on cable insulation

2.5.4 Load Cells

To attach a cable from a load cell or junction box, route the cable to the J1 connector. Wire the load cell cable from the load cell or junction box to connector J1 as shown in Table 2-3. If using 6-wire load cell cable (with sense wires), open the unit (see Section 2.4.1 on page 14) and remove jumpers JP1 and JP2.

For 4-wire installation, leave jumpers JP1 and JP2 on (see Figure 2-11 on page 19).

Connector Pin Function

1 +SIG 2 –SIG

For 6-wire load cell connections, remove jumpers JP5 and JP6.

The shield wire will attach to the ground clamp on the backplate.

3 +SENSE 4 –SENSE 5 +EXC 6 –EXC

Table 2-3. J1 Pin Assignments

2.5.5 Cable Shield Grounding

Except for the power cord, all cables routed through the cord grips must be shield grounded against the enclosure.

• Use hardware provided in the parts kit to install shielding clamps on the grounding studs at the bottom of the enclosure

• Install only the necessary amount of shielding clamps for the cord grips to be used; finger tighten nuts at this time

• Route cables through the cord grips and shielding clamps to determine the cable lengths required to reach the appropriate cable connectors

• Mark the cables to remove the insulated jackets and shielding as described in the next two sections

Foil Shielded Cable

Figure 2-6. Foil Shielded Cable

1. Strip the insulated jacket and foil 1/2'' (15 mm) past the shielding clamp.

2. Strip another 1/2'' of the insulated jacket, leaving the foil shielding exposed.

3. Fold the foil shielding back on the cable where the cable passes through the clamp.

4. Ensure the silver (conductive) side of the foil is turned outward.

5. Wrap the shield wire around the cable so it contacts the foil where the cable passes through the clamp.

6. Torque the shielding clamp nut to 10 in-lb (1.13 N-m) so the clamp is around the cable and contacting the shield wire.

16 Visit our website www.RiceLake.com

Page 23

Installation

Braid

Note

Braid Shielded Cable

Cut insulated jacket here

Figure 2-7. Braid Shielded Cable

1. Strip the insulated jacket and braided shielding from a point just past the shielding clamp.

2. Strip another 1/2'' (15 mm) of the insulated jacket, leaving the braid exposed where the cable passes through the clamp.

3. Tighten the shielding clamp nut.

2.5.6 882IS Enclosure Grounding

Proper grounding must be done between the power supply and the backplate of the indicator. The preferred grounding method is illustrated in Figure 2-8.

Figure 2-8. Grounding Bond

2.5.7 CPU Board Replacement

1. Disconnect power to the indicator.

2. Remove the backplate from the enclosure. See Section 2.4.1 on page 14.

Label connections for re-installation of board.

3. Disconnect cables from the CPU board.

4. Remove the four screws from the CPU board.

5. Lift the CPU board out of the enclosure.

To install the new board, reverse the above procedure. Be sure to reinstall cable ties to secure all cables inside the indicator enclosure.

Page 24

882IS/882IS Plus

DC Cable Grounding in 882IS

Except for the power cord, all cables routed through cord grips should be grounded against the indicator enclosure, including the DC cable. Do the following to ground the DC cable.

Attaches to the inside of the enclosure backplate

Figure 2-9. DC Grounding Stackup

1. Run three (not included) 22-16 AWG wires (5-10 mm diameter) up through the cord grip.

2. One wire will be terminated (grounded) at a stud near the cord grip using the grounding stackup (

3. Run the other two wires up the side of the indicator and connect the three pin plug (PN 15888) to the power supply

board as shown in Figure 2-10 and Table 2-3.

Figure 2-9

J4 Power

Figure 2-10. Connect DC Wiring

18 Visit our website www.RiceLake.com

Page 25

Installation

2.5.8 Serial Communications – Port 1 (COM)

Connector J3A (see Figure 2-11) provides connections for the four-wire RS-422 serial communications. Table 2-4 shows the pin assignments.

Pin RS-422

1 GND 2 DRX (-) 3 DRX (+) 4 DTX (-) 5 DTX (+)

Table 2-4. J3A Pin Assignments (Port 1 Serial Communications)

2.6 CPU Board

JP4 Audit

Trail

JP3 Setup/

Config

JP1 and JP2

Load Cell Sense

Jumpers

J1 Load Cell

J2 Digital

Input

Figure 2-11. 882IS CPU Board

Connector Description

J1 Load Cell Connection J2 Digital Input J3A Communication RS-422 J4 Power Connection JP1 Load Cell Sense JP2 JP3 Configuration/Setup JP4 Audit Trail

Table 2-5. CPU Board Connectors

J3A

RS-422

Fiber Optic

J3 Power

Page 26

882IS/882IS Plus

C22

JP4

R45

R18

R24

C28

R44

R30

JP3

R25

R47

R46

Coupon

GND

CNFIG

OFF

AUDIT

2.7 Audit Trail

The 882IS includes an audit trail feature that keeps track of the calibration count and the configuration count. On the top of the CPU board is a 3-pin jumper (JP4) that enables or disables this feature. If the jumper is set to on, the 882IS

allows entry to the setup and calibration menus using only the front panel

Figure 2-12. Audit Trail Jumper Position

• To use the audit trail and allow the use of the Menu key to enter the configuration and calibration mode, place the jumper in the On position

• To prevent the use of the

Menu key to enter the configuration and calibration mode, instead requiring use of the

externally seal-able setup switch located inside the enclosure (see Figure 3-1 on page 23), place the jumper in the Off position

The audit trail counters will operate in either position of the audit jumper.

Menu key.

2.8 Digital Inputs

Digital inputs can be set to provide many indicator functions, including all keypad functions except MENU. Digital inputs are active low (0 VDC) and inactive high (5 VDC). Use the Digital Inputs menu (Section 3.2.15 on page 37) to configure the digital inputs.

Table 2-6 shows the digital inputs pin assignments for connector J2.

Connector Pin Signal

1 GND

Table 2-6. J2 Pin Assignments (Digital Inputs)

2.9 Backplate Attachment

Once cabling is complete, reattach the backplate ground wire to the backplate. Position the backplate over the enclosure and install the eight backplate nuts. Use the torque pattern shown in Figure 2-13 to prevent distorting the backplate gasket. Torque nuts to 15 in-lb (1.7 N-m).

2 DI2 3 DI1

20 Visit our website www.RiceLake.com

Figure 2-13. Torque Pattern

Page 27

Installation

Note

2.10 Legal for Trade Sealing

In certain Legal for Trade applications, it may be necessary to seal the indicator to restrict access from the setup switch. Use the following steps to seal the indicator.

1. Place the sealing wire through the fillister head screws on the backplate, then through the fillister head screw at the

bottom of the indicator, as shown in Figure 2-14.

2. Seal the wire to secure.

Figure 2-14. Sealing the Indicator

2.11 IO Module Option Cards

The following interfaces are available through an IO module connected to the 882IS via fiber optics. Connector J8 is reserved for the option cards. Table 2-7 lists the options available for the 882IS indicator. Each kit includes

instructions for installing and setting up the option.

Option Kit Part Number Option Manual Part Number

179156 Analog Output 156858 179158 EtherCat 195260 179159 EtherNet/IP 179160 ProfiNet 179161 Modbus TCP 179162 DeviceNet 179163 Profibus DP

Table 2-7. Available Option Cards

2.12 Rechargeable Battery Usage

The 882IS uses an optional, FM approved, rechargeable, IS6V2 battery (PN 180831). When the battery voltage on connector J3 reaches approximately 5.55 volts, the indicator display shows Low Battery Life Replace or Charge. Replace/recharge the battery when this warning is displayed to prevent data loss before a complete shutdown. Battery life will vary depending on use and power saving mode. To preserve battery life, disconnect the battery when not in use.

Even if the 882IS is turned off, the indicator still draws a small amount of power while connected.

Detailed information on IS6V2 battery pack can be found in the installation addendum (PN 194893).

Page 28

882IS/882IS Plus

TO GROUND STUD

ON BACKPLATE

2.13 Replacement Parts

Figure 2-15. 882IS Indicator Parts Drawing

Item No. Part No. Description

174791 Board Assembly, CPU 882IS Display, ROHS Compliant

180824 Machine Screw, Phillips Pane Head 18-8 sst

44845 Setup Switch Assembly

180856 Washer, M4 Internal Tooth SST

180826 Nut, Kep External Tooth Lock Washer 18-8 SST

15601 Ground Wire 6 inch w/ Number 8 Eye Connector

46381 #10 Bonded Sealing Washer, 18-8 Stainless Steel

180861 Screw, Machine Slotted Drilled Cheese Head, SST

177707

882IS Plus

180829

882IS Qty

Qty

1 1 4 4 1 1 3 3 7 7 1 1 1 1 1 1

Table 2-8. 882IS Replacement Parts

22 Visit our website www.RiceLake.com

Page 29

Configuration

IMPORTANT

Note

3.0 Configuration

To configure the 882IS indicator, the indicator must be placed in setup mode. The setup switch is accessed through a small hole on the bottom of the enclosure. Insert a non-conductive tool into the access hole and press the setup switch to put the indicator into setup mode.Scale displays.

Use caution when inserting the non-conductive tool into the bottom of the enclosure. Only press the tool in about 3/4 inch (19 mm) to engage the setup switch. Do not use excessive force that may damage the switch.

If the audit trail is enabled, setup mode may be accessed by pressing .

Setup Switch Access

Figure 3-1. Bottom View – Setup Switch Access

When the indicator is placed in setup mode, the word Scale displays. The Scale menu is the first of eight second-level menus used for configuring the indicator. Detailed descriptions of these menus are given in Section 3.2.2 on page 25.

When setup is complete, press to return to the weigh mode.

3.1 Configuration Methods

The 882IS indicator can be configured by using the front panel keys to navigate through a series of configuration menus or by sending commands or configuration data to the data communication port. Configuration using the menus is described in

Section 3.2 on page 24.

Configuration using a data communication port can be accomplished using either the EDP command set (see Section 6.0 on

page 53) or the Revolution configuration utility (see Section 5.2 on page 51).

Page 30

882IS/882IS Plus

Audit Setup

Accumulator

Tare

Test Time & Date

LRV1.00 Calibration

number

Configuration

number

Audit

3.2 User Setup Menu

The 882IS indicator can be configured using a series of menus accessed through the indicator front panel. Table 3-1 summarizes the functions of the user setup menu.

Figure 3-2. 882IS Menu Layout

Menu User Menu Function

Audit Audit Trail - Displays the (LRV) legally relevant firmware version, configuration count and calibration count. See

Section 3.2.1

Setup Used to enter configuration mode, if audit trail is enabled. See Section 3.2.2 on page 25 Test System test functions. See Section 3.3 on page 44 Time & Date Used to view or set time and date. See Section 3.4 on page 44 Accumulator View, print or clear the current accumulator value, if enabled. See Section 3.5 on page 44 Tare Views the current tare value. See Section 3.6 on page 44

Table 3-1. 882IS Plus Menu Summary

The following sections provide graphic representations of the 882IS menu structures. In the actual menu structure, the settings under each parameter are arranged horizontally. To save page space, menu choices are shown in vertical columns. The factory default setting appears at the top of each column in bold letters. Parameters shown surrounded by a dotted-line box only appear under the special circumstances explained inside each box.

Most menu diagrams are accompanied by one or more tables that describe all parameters and parameter values associated with that menu.

3.2.1 Audit Menu

Figure 3-3. Audit Menu Structure

Menu Description

LRV Legally relevant firmware version (read only) Calibration Displays total calibration events (read only) Configuration Displays total configuration events (read only)

Table 3-2. Audit Menu Parameters

24 Visit our website www.RiceLake.com

Page 31

Configuration

Scale

Setup

Digital Inputs IO Module VersionFeatures Ports Print Formats Power Savings

Graduations

Setup

Filter

Threshold

Filter

Sensitivity

Sample

Rate

Display

Rate

Stand Still

Time

Overload

Zero

Track Band

Scale

Split Format

Zero Range

Motion Band

Tare

Enable

Start

Mode

Accumulator Calibrate

3.2.2 Setup Menu

Figure 3-4. Setup Menu Structure

Menu Description

Scale Use the Scale menu to configure and calibrate the scale. See Figure 3-5 for the Scale menu structure Features Use the Features menu to set miscellaneous system attributes. See Figure 3-9 for the Features menu structure Ports Use the Ports menu to configure communication ports. See Figure 3-13 for the Ports menu structure Print Format Use the Print Format menu to set the print format used for header, gross, net and accumulator formats

See Figure 3-16 for the Print Format menu structure Digital Inputs Use the Digital Inputs menu to assign digital output functions. See Figure 3-17 for the Digital IO menu structure IO Module Use the IO Module menu to configure the IO module features (if installed). See Figure 3-22 for the IO Module menu structure Power Savings Use the power savings menu to configure the power saving mode, wake threshold, backlight control and battery support Version Use the Version menu to display the installed firmware version number. See Figure 3-23 for the Version menu structure

Table 3-3. Setup Menu Parameters

3.2.3 Scale Menu

Menu Choices Description

Graduations 10000

Split OFF

Format Primary

Zero Track Band 0

1-100000

2RNG 3RNG 2INTVL 3INTVL

Format

0.0-100

Figure 3-5. Scale Menu Structure

Graduations – specifies the number of full scale graduations if Split=OFF. (For multi-range and multi-interval scales (SPLIT is not or interval.)

The value entered must be in the range 1–100000 and should be consistent with legal requirements and environmental limits on system resolution. To calculate Graduations, use the formula: Graduations = Capacity / Display Divisions. Display divisions are specified under the Format submenu.

Multi-range/Interval – specifies whether the scale is full-range (OFF), multi-range (2RNG, 3RNG), or multi-interval (2INTVL, 3INTVL). For multi-range and multi-interval scales, see the submenu shown in Figure 3-7 and parameter descriptions in Table 3-6.

See Figure 3-7 for menu structures. For standard scales see “If SPLIT = OFF”, for multi-range/interval scales see “If SPLIT = 2RNG, 3RNG, 2INTVL, or 3INTVL” or secondary format.

Zero Track Band – automatically zeros the scale when within the range specified, as long as the weight is within the Zero Range and scale is at standstill. Specify the zero tracking band in ± display divisions. The maximum legal value varies depending on local regulations.

Off), the Graduations value is derived from the capacity and display divisions specified for the range

Table 3-4. Scale Menu Parameters

Page 32

882IS/882IS Plus

Menu Choices Description

Zero Range 1.900000

0.0-100

Motion Band 1

0-100

Overload FS+2%

FS+1D FS+9D FS FS+Percentage

Standstill Time 10

1-65535

Display Rate 1

1-80

Sample Rate 60HZ

120HZ

7.5HZ 15HZ 30HZ

Filter Sensitivity LIGHT

MEDIUM HEAVY

Filter Threshold 0

0-99999

Tare Enable BOTH

NOTARE PBTARE KEYED

Start Mode GO

DELAY

Accumulator OFF

Calibrate WZERO

WVAL WSPAN WLIN REZERO LAST TEMP

Zero Range – selects the range within which the scale can be zeroed. The 1.900000 default value is ±1.9% around the calibrated zero point, for a total range of 3.8%. Indicator must be at standstill to zero the scale. Maximum legal value varies depending on local regulations.

Motion Band – sets the level, in display divisions, at which scale motion is detected. If motion is not detected for the time defined by the standstill parameter, the standstill symbol lights. Some operations, including print, tare, and zero, require the scale to be at standstill. Maximum legal value varies depending on local regulations. If this parameter is set to 0 the standstill annunciator is always lit; operations normally requiring standstill (zero, tare, print) are performed regardless of scale motion. If 0 is selected, Zero Track Band must also be set to 0.

Overload – Determines the point at which the display blanks and an out-of-range error message is displayed. Maximum legal value varies depending on local regulations.

If FS+Percentage is selected, a sub-menu is enabled. At FS+Percentage, press the down arrow to access the Enter Percentage parameter. Press the down arrow at Enter Percentage to view the current value. Edit as needed. Values are 0.0 - 150.0

Standstill Time – specifies the length of time the scale must be out of motion, in 0.1-second intervals, before the scale is considered to be at standstill.

Display update rate – Specifies the display update rate, in the number of 100-millisecond intervals between updates.

Sample rate – Selects measurement rate, in samples per second, of the analog-to-digital converter. Lower sample rate values provide greater signal noise immunity. A setting of 120 Hz may be too fast to provide the desired stability in some static weighing applications.

Digital filtering sensitivity – the amount of influence the current A/D cycle has on the running averaged value. The Light setting will respond quicker to an applied weight to immediately impact the displayed value. Medium and Heavy settings are for applications where weighing times are longer and expected weight changes are larger.

Digital filter cutout threshold – controls the response of the filter and must be set above the noise disturbances in the system. Value is in grads. If set to zero there is no filtering.

Tare function – Enables or disables push-button and keyed tare.

BOTH – Both push-button and keyed tares are enabled NOTARE – No tare allowed (gross mode only) PBTARE – Push-button tares enabled KEYED – Keyed tare enabled

Start mode.

GO - The indicator goes into operation immediately after a brief power up display test. DELAY - The indicator performs a power up display test, then enters a 30-second warm up period. If no

motion is detected during the warm up period, the indicator becomes operational when the warm up period ends; if motion is detected, the delay timer is reset and the warm up period repeated.

Accumulator – specifies if the scale accumulator is enabled or disabled. If enabled, accumulation occurs every time a print operation is performed, while the weight is above zero, as long as the weight returns to a value lower than the threshold between print operations.

Calibration – See Figure 3-8 for descriptions, and see Section 4.0 for calibration procedures.

Table 3-4. Scale Menu Parameters (Continued)

26 Visit our website www.RiceLake.com

Page 33

3.2.4 Scale Format Menu - if Split = Off

Scale

Format

Primary

Setup

2 D

5 D

Display

Divisions

Secondary

Decimal Point

888880

888888

8.88888

88.8888

888.888

8888.88

88888.8

Units

NONE

Display

Divisions

Decimal Point Units

2 D

5 D

888880

888888

8.88888

88.8888

888.888

8888.88

88888.8

NONE

OFF

Configuration

Figure 3-6. Format Menu Structure

Menu Choices Description

Primary Decimal Point

Display Divisions Units

Secondary Decimal Point

Display Divisions Units

Decimal Point 888888

888880

8.88888

88.8888

888.888

8888.88

88888.8

Display Divisions 1D

2D 5D

Units

KG OZ TN T G NONE OFF

Primary Units – Settings determine the scale capacity and specifies the decimal point, display division and units used

Secondary Units – Settings determine the Secondary, or Alternate, units value, decimal location, and display division size

Decimal Point Location – when combined with the display divisions, specifies the location of the decimal point or dummy zeroed in the unit display

Defaults: Primary – 888888 Secondary – 88888.8

Display Divisions – when combined with the decimal point location, specifies the minimum division size for the displayed weight Example: (88888.8 X 1D) X 5000 grads = 500 lb scale, counting by 1 Defaults: Primary – 1D Secondary – 5D

Units – Specifies units for displayed and printed weight

LB = pound – Primary default KG = kilogram – Secondary default OZ = ounces TN = short ton T = metric ton G = gram NONE = no units icon is shown on the display and no units text is included in print or stream output OFF = prevents the 882IS from displaying secondary units

Table 3-5. Format Menu Parameters

Page 34

882IS/882IS Plus

Scale

Format

Decimal Point 1

Setup

Display Division1 Range 1 Max

Units

Decimal Point 2

Display Division2

Range 2 Max Decimal Point 3

Display Division3 Range 3 Max

3.2.5 Scale Format Menu - if split = 2 RNG, 3 RNG, 2 INTVL, 3 INTVL

Figure 3-7. Split Format Menu Structure

Menu Choices Description

Decimal Point-1 Decimal Point-2 Decimal Point-3

Display Divisions 1 Display Divisions 2 Display Divisions 3

Range 1 Max Range 2 Max Range 3 Max

Units

888888 888880

8.88888

88.8888

888.888

8888.88

88888.8 1D

2D 5D

Decimal Range Max - specifies the upper weight limit of the given interval or range

LB KG OZ TN T G NONE

Decimal Point Location – Specifies the location of the decimal point or dummy zeroed in the unit display Defaults: Decimal point 1 - 888888 Decimal point 2 - 88888.8 Decimal point 3 - 8888.88

Display Divisions – when combined with the decimal point location, specifies the minimum division size for the displayed weight Defaults: Display divisions 1 - 1D Display divisions 2 and display divisions 3 - 5D

Defaults: Range 1 max - 2000.0 Range 2 max - 5000.0 Range 3 max - 10000.0

Units – Specifies units for displayed and printed weight

LB = pound KG = kilogram OZ = ounces TN = short ton T = metric ton G = gram NONE = no unit icon is shown on the display and no units text is included in print or stream format

Table 3-6. Split Format Menu Parameters

28 Visit our website www.RiceLake.com

Page 35

3.2.6 Calibration Menu

Scale

Calibrate

Zero Calibration

Setup

Test Weight

Count Value Count Value Point 1 - 5 Count Value

Calibrate

Span Calibration

Linear Calibration

Rezero Last Zero

Temporary Zero

Count Value

Calibrate

Count Value

Calibrate

Decimal

Calibrate

Calibration

Point 1

Weigh Point 1

Decimal

Count Value

Calibrate

Figure 3-8. Calibration Menu Structure

Menu Choices Description

Zero Calibration —

Test Weight 0.00001 —

9999999.0

Span Calibration —

Linear Calibration Point-1 —

Point-5

Rezero —

Last —

Temporary Zero —

Press

Enter to display previous A/D raw counts. Press Enter again to perform a zero calibration, press Menu to

cancel Press

Enter to display and edit the test weight value

Enter to display previous A/D raw counts. Press Enter again to perform a span calibration, press Menu to

Press cancel

Press

Enter to display and edit test weight and calibration values for up to five linearization points.

Perform linear calibration only after Zero calibration and Span calibration have been performed Press

Enter to remove an offset value from the zero and span calibrations.

Note: Use Rezero only after Zero Calibration and Span Calibration have been set. See Section 4.1 on

page 45 for more information about using Rezero.

Press

Enter to recall the last established push button zero to allow calibration without removing weight from scale.

See Section 4.2 on page 47. Press

Enter to temporarily zero the displayed weight from a loaded scale. See Section 4.3 on page 47.

Table 3-7. Calibration Menu Parameters

Configuration

Page 36

882IS/882IS Plus

Features

Setup

Region Unit ID

Consecutive

Number

Password Key Lock

Gravity

Compensation

Latitude Elevation

OFF

Integer

Hidden menus if gravity compensation is OFF

0-90 -9999 - 9999

Current Value Reset Value

User Setup

Alpha/ Numeric

Integer

0-999999

Integer

0-999999

Integer

0-999999

Integer

0-999999

3.2.7 Features Menu

Figure 3-9. Features Menu

Menu Choices Description

Region Regulation

Regulation Word

Decimal Format

Unit ID 000000 Sets the unit ID, a string of up to 6 ASCII characters, which can be set via serial port or keypad. This will be used

Consecutive Number

Current Value

Reset Value

Password User

Setup

Keylock Zero

Gross Net

Units

Tare

Numeric Keypad

Function Key

Gravity Compensation

Off

Latitude 45

0-90

Elevation 345

-9999 to +9999

Selects regional settings. See Level 3 sub menus, Figure 3-10 on page 31

in place of the <UID> token in a print format. The default value is “1.” Allows sequential numbering for print operations. The consecutive number value is incremented following each

print operation that includes <CN> in the ticket format. When the consecutive number is reset, it is reset to the Reset value specified in the parameter.

Sets a password to access the Setup menu, or certain sub-menus in the User menu. Specify a non-zero value to enable the password. The Setup password protects the entire Setup menu, and when set is required even when attempting entry into the Setup menu using the setup switch. The User password restricts access to the Time/Date and Accumulator sub-menus in the User menu. Passwords can be overridden by loading new firmware, or entering 999999.

Note: Overriding passwords will clear configuration and calibration settings. To preserve settings (i.e., ID information), use Revolution software to upload the data to a PC, then download it back to the 882IS after the password override is performed.

Disables the listed keys. Select Lock to disable the key, and Unlock to enable the key

Gravity compensation enable/disable

Press

Enter to display and edit the latitude in degrees for gravity adjustment to calibration

(Gravity compensation must be set to On) Press

Enter to display and edit the elevation in meters for gravity adjustment to calibration

(Gravity Compensation must be set to On)

Table 3-8. Features Menu Parameters

30 Visit our website www.RiceLake.com

Page 37

3.2.8 Region Menu

Features

Region

Regulation

Word

Decimal

Format

Y2DDMM

Y2MMDD

MMDDY4

DDMM4

Y4MMDD

Y4DDMM

MMDDY2

DDMMY2

GROSS

BRUTTO

DOT

COMMA

OIML

NTEP

CANADA

INDUST

NONE

Time Format

Time

Time Separator Set

12HOUR

24HOUR

COLON

COMMA

000000

Date

Time Format Time Separator Set

SLASH

DASH

000000

SEMI

Configuration

Figure 3-10. Region Menu Structure

Menu Choices Description

Regulation OIML

NTEP

Canada Industrial None

Regulation Word Gross

Brutto

Decimal Format Dot

Comma

Time Time Format

Time Separator Set

Date Date Format

Date Separator Set

Regulatory mode – Specifies the regulatory agency having jurisdiction over the scale site

Note:The value specified for Regulation affects the function of the front panel Tare and Zero keys.

• OIML, NTEP, and CANADA modes allow a tare to be acquired at any weight greater than zero. NONE allows tares to be acquired at any weight value.

• OIML, NTEP, and CANADA modes allow a tare to be cleared only if the gross weight is at no load. NONE allows tares to be cleared at any weight value.

• NTEP and OIML modes allow a new tare to be acquired even if a tare is already present. In CANADA mode, the previous tare must be cleared before a new tare can be acquired.

• NONE, NTEP and CANADA modes allow the scale to be zeroed in either gross or net mode as long as the current weight is within the specified Zero Range. In OIML mode, the scale must be in gross mode before it can be zeroed; pressing the and clear the tare, if weight is within the specified Zero Range.

• Selecting a particular Regulation will default the sub-parameters items to match. The user can then change the sub-parameters as they wish NOTE: changing the sub-parameters may violate local regulations.

Sets the term displayed when weighing in gross mode. Selecting BRUTTO replaces the Gross annunciator with Brutto

Specifies whether decimal numbers are displayed using a period (DOT) or a comma

Allows selection of time format and time separator character

Allows selection of date format and date separator character

Table 3-9. Region Menu Parameters

Zero key in net mode will zero the scale

Page 38

882IS/882IS Plus

Features

Region

Regulation

INDUST

Remove Tare

on Zero

Snapshot Keyed Tare Negative/Zero

Tare

Multiple Tare

Clear of Tare/

Accum

Round Tare Print in Motion

Print PT Overload Base

Audit Agency

YES

DISPLAY

SCALE

YES

CALIB

SCALE

NTEP

CANADA

REPLAC

REMOVE

NOTHIN

NONE

OIML

3.2.9 Region - Regulation - Indust

Figure 3-11. Region Regulation Menu Structure

Menu Choices Description

Snapshot Display

Remove Zero Tare No

Keyed Tare Yes

Multiple Tare Replace

Negative/Zero Tare No

Clear of Tare/Accumulator Yes

Round Tare Yes

Print in Motion No

Print Preset Tare No

Overload Base Calibrate

Audit Agency NTEP

Scale

Yes

Remove Nothing

Yes

Scale

CANADA NONE OIML

Table 3-10. Region Regulation Parameters

Display or scale weight source

Remove tare on Zero

Always allow keyed tare

Replaces existing Tare when the Tare key is pressed

Allow negative or zero tare

Clear key to clear tare/accumulator

Allow

Round semi-automatic (pushbutton) tare to the nearest display division

Allow print while in motion

Add PT to keyed tare print

Uses either the calibrated zero or the scale zero for overload calculation

Regulatory agencies

32 Visit our website www.RiceLake.com

Page 39

3.2.10 Keylock Menu

Features

Key Lock

Zero

Setup

Gross/Net Units

Tare Menu

Numeric Keypad Function Keys

Serial Port

Setup

Ports

Fiber Optic

Figure 3-12. Keylock Menu Structure

Menu Description

Zero Lock or unlock individual keys; Settings: UNLOCK (default), LOCK Gross/Net Units Print Tare Menu Numeric Keypad Function Keys

NOTE: The Num parameter locks or unlocks all of the numeric keys. The numeric keys cannot be individually controlled.

Table 3-11. Keylock Menu Parameters

Configuration

3.2.11 Setup Ports Menu

Figure 3-13. Ports Menu Structure

See Section 3.2.12 on page 34 for Serial Ports menu choices and Section 3.2.13 on page 35 for Fiber Optic Ports menu choices.

Page 40

Ports

Serial Port

Trigger

Setup

Baud Bits Stop Bits Termination

Echo Response

End of Line Delay

Stream FormatPrint MessageType

882IS/882IS Plus

3.2.12 Ports - Serial Ports Menu

Figure 3-14. Serial Ports Menu Structure

Menu Choices Description

Trigger Command Setting Trigger to command allows operation of EDP commands and can print

Stream Industrial Stream Industrial scale data – data is updated up to the configured sample rate.

Allows operation of EDP commands and printing

Stream Legal for Trade Stream Legal for Trade data – data is updated at the configured display update rate.

Allows operation of EDP commands and printing

Remote Configures the port to operate as a serial scale input. See Menu Structure if Trigger is set to REMOTE

below

Baud 9600

19200 28800 38400 57600 115200 1200 2400 4800

Bits 8None

7Even 7Odd

Stop Bits 1

Termination CR/LF

Echo On

Off

Response On

Off

End of Line Delay 0

0-255 Type 422 Specifies the physical type of serial Print Message On

Off Stream Format <2><P><W7.>

Port baud rate

Port data bits and parity

Stop Bits – selects the number of stop bits transmitted and the number of stop bits expected to be received by the port

Termination – selects the termination character(s) for data sent from the port carriage return (CR) line feed (LF)

Specifies whether characters received by the port are echoed back to the sending unit

Response – specifies whether the port transmits replies to serial commands

End of Line Delay - specifies, in 0.1 second intervals, the delay between transmitted lines of data

Print message – displays a message when a print is transmitted on this port

Stream format – specifies the stream format used for streaming output of scale data (Trigger=STRLFT or STRIND) or specifies the expected input for a serial scale (Trigger=REMOTE)

Table 3-12. Serial Ports Menu Parameters

34 Visit our website www.RiceLake.com

Page 41

Ports

Fiber Optic Port

Trigger

Setup

Baud Bits Stop Bits Termination

Echo Response

End of Line Delay

Print Message Stream Format

3.2.13 Ports - Fiber Optics Menu

Figure 3-15. Fiber Optics Menu Structure

Menu Choices Description

Trigger Command Setting Trigger to command allows operation of EDP commands and can print

Stream Industrial Stream Industrial scale – data is updated up to the configured sample rate.

Allows operation of EDP commands and printing

Stream Legal for Trade

Remote Configures the port to operate as a serial scale input. See Menu Structure if Trigger is set to REMOTE below

Baud 9600

19200 28800 38400 57600 115200 1200 2400 4800

Bits 8None

7Even 7Odd

Stop Bits 1

Termination CR/LF

Echo On

Off

Response On

Off

End of Line Delay 0

0-255

Print Message Off

Stream Format <2><P><W7.>

Stream Legal for Trade – data is updated at the configured display update rate. Allows operation of EDP commands and printing

Port baud rate

Port data bits and parity

Stop Bits – selects the number of stop bits transmitted and the number of stop bits expected to be received by the port

Termination – selects the termination character(s) for data sent from the port

Specifies whether characters received by the port are echoed back to the sending unit

Response – specifies whether the port transmits replies to serial commands

End of Line Delay - specifies, in 0.1 second intervals, the delay between transmitted lines of data

Print message – displays a message when a print is transmitted on this port

Stream format – specifies the stream format used for streaming output of scale data (Trigger=STRLFT or STRIND) or specifies the expected input for a serial scale (Trigger=REMOTE).

Table 3-13. Fiber Optics Menu Parameters

Configuration

Page 42

882IS/882IS Plus

Print Format

Gross Format

Net Format

Format

Setup

Accumulator Header Format

Port Format Port Format Port Format

Gross Format

String

IOCOM

COM

FIBER

Net Format

String

Accumulator

Format String

Header

Format String

ETHCLIENT

IOCOMUSB

ETHSERVER

OFF

IOCOM

COM

FIBER

ETHCLIENT

IOCOMUSB

ETHSERVER

OFF

IOCOM

COM

FIBER

ETHCLIENT

IOCOMUSB

ETHSERVER

OFF

3.2.14 Print Format Menu

See Section 7.3 on page 64 for information about custom print formatting.

Figure 3-16. Print Format Menu Structure

Menu Choices Description

Gross Format Format Alphanumeric, Max Length: 1000

Weigh mode, no tare in system, GROSS<G><NL2><TD><NL>

Port The communications port the print data will be sent to: COM, FIBER, IOCOM, IOCOMUSB, ETHSERVER,

ETHCLIENT, OFF.

Net Format Format Alphanumeric, Max Length: 1000

Weigh mode, tare in system, GROSS<G><NL>TARE<SP><T><NL>NET<SP2><N><NL2><TD><NL>

Port The communications port the print data will be sent to: COM, FIBER, IOCOM, IOCOMUSB, ETHSERVER,

ETHCLIENT, OFF

Accumulator Format Alphanumeric, Max Length: 1000

Accumulator enabled and displayed, ACCUM<A><NL><DA><TI><NL>

Port The communications port the print data will be sent to: COM, FIBER, IOCOM, IOCOMUSB, ETHSERVER,

ETHCLIENT, OFF

Header Format Format Alphanumeric, Max Length: 300

Must be inserted into other print format COMPANY NAME<NL>STREET ADDRESS<NL>CITY, ST ZIP<NL2>

Table 3-14. Print Format Menu Parameters

36 Visit our website www.RiceLake.com

Page 43

3.2.15 Digital Inputs Menu

Digital Inputs

Slot 0

Bit 1

Setup

Bit 2

Figure 3-17. Digital Inputs Menu Structure

Menu Choices Description

Level 2 submenus

Slot 0 Bit 1

Bit 2 Slot 0 submenu Bit 1

Bit 2

Off

Zero

Tare

Units

Clear

DSPTAR

DSPACC

NT/GRS

CLRCN

KBDLOC

GROSS

NET

PRIM

SEC

CLRTAR

CLRACC

Select the bit to set the function

Specifies the function activated by Bits 1–2.

• PRINT, ZERO, TARE, UNITS, NT/GRS provide the same functions as the five front panel keys

• DSPTAR displays the tare

• DSPACC displays the current accumulator value

• CLRCN resets the consecutive number to the value specified on the Reset value parameter (Features menu)

• KBDLOC locks the keyboard

• GROSS, NET, PRIM and SEC select gross or net weight display, and primary or secondary units display modes

• CLRTAR clears the current tare

• CLRACC clears the accumulator

Configuration

Table 3-15. Digital Input Menu Parameters

Page 44

882IS/882IS Plus

Ports

Setup

IO Module

Communication Port

Trigger Baud

Bits Stop Bits

Termination

Echo Response

End of Line Delay

Type

Print Message Stream Format

3.2.16 IO Module Menu

IO Module - Ports Menu

Menu Choices Description

Trigger Command Setting Trigger to command allows operation of EDP commands and can print

Baud 9600

Bits 8None

Stop Bits 1

Termination CR/LF

Echo On

Response On

End of Line Delay

Type 422 Specifies the physical type of serial Print Message Off

Stream Format <2><P><W7.>

Figure 3-18. IO Module Ports Menu Structure

Stream Industrial Stream Industrial scale – data is updated up to the configured sample rate.

Allows operation of EDP commands and printing

Stream Legal for Trade

Stream Legal for Trade – data is updated at the configured display update rate. Allows operation of EDP commands and printing

Remote Configures the port to operate as a serial scale input. See Menu Structure if Trigger is set to REMOTE below

Port baud rate 19200 28800 38400 57600 115200 1200 2400 4800

Port data bits and parity 7Even 7Odd

Stop Bits – selects the number of stop bits transmitted and the number of stop bits expected to be received by 2

the port

Termination – selects the termination character(s) for data sent from the port CR

Specifies whether characters received by the port are echoed back to the sending unit Off

Response – specifies whether the port transmits replies to serial commands Off

End of Line Delay - specifies, in 0.1 second intervals, the delay between transmitted lines of data 0-255

Print message – displays a message when a print is transmitted on this port On

Stream format – specifies the stream format used for streaming output of scale data (Trigger=Stream Legal for <U><M><S>

Trade or Stream industrial) or specifies the expected input for a serial scale (Trigger=REMOTE). <CR><LF>

Table 3-16. IO Module Ports Menu Parameters

38 Visit our website www.RiceLake.com

Page 45

IO Module - USB

Ports

Setup

IO Module

USB

COMMUNICATIONS

Trigger Termination

Echo Response

End of Line Delay

Print Message Stream Format

Figure 3-19. IO Module USB Menu Structure

Menu Choices Description

Trigger Command Setting Trigger to command allows operation of EDP commands and can print

Stream Industrial

Stream Legal for Trade

Remote Remote - Configures the port to operate as a serial scale input. See Menu Structure if Trigger is set to REMOTE below

Termination CR/LF

Echo On

Off

Response On

Off

End of Line Delay

0-255

Print Message Off

Stream Format <2><P><W7.>

Stream Industrial scale – data is updated up to the configured sample rate. Allows operation of EDP commands and printing

Stream Legal for Trade – data is updated at the configured display update rate. Allows operation of EDP commands and printing

Termination – selects the termination character(s) for data sent from the port

Specifies whether characters received by the port are echoed back to the sending unit

Response – specifies whether the port transmits replies to serial commands

End of Line Delay - specifies, in 0.1 second intervals, the delay between transmitted lines of data

Print message – displays a message when a print is transmitted on this port

Stream format – specifies the stream format used for streaming output of scale data (Trigger=Stream Legal for Trade or Stream industrial) or specifies the expected input for a serial scale (Trigger=REMOTE).

Table 3-17. IO Module USB Menu Parameters

Configuration

Page 46

882IS/882IS Plus

Ports

Setup

IO Module

Ethernet

DHCP IP Address

Network Mask

Default Gateway

Primary DNS

Secondary DNS

EtherNet Server

Ethernet Client

MAC Address

Server

TCP Port

Server Trigger Termination

Server

EOL Delay

Server Timeout Stream Format Server Echo

Server

Response

Client Remote IP

Client Remote Port

Client Trigger Termination

Client EOL Delay

Client Timeout

Client Stream Format

Client Echo

Client Response

IO Module - EtherNet

DHCP Dynamic Host Configuration Protocol; Settings: ON (default), OFF

IP Address IP address (000.000.000.000) Netmask Netmask (000.000.000.000) Default Gateway IP address for the Default Gateway; (000.000.000.000) Primary DNS IP address for the primary DNS server; (000.000.000.000) Secondary DNS IP address for the secondary DNS server; (000.000.000.000) EtherNet Server See sub-menu parameters below EtherNet Client See sub-menu parameters below Mac Address The MAC address for this device; (Read Only)

Client Remote IP Address Client only: the IP address of the remote server of the IO module is connecting to (000.000.000.000) Server TCP Port The port on the 882IS IO module for a remote client to connect to Server Trigger Termination Selects the termination characters for data sent from the port Server EOL Delay Specifies, in 0.1 second intervals, the delay between transmitted lines of data

Figure 3-20. IO Module EtherNet Menu Structure

Menu Description

If DHCP is ON, the five parameters below are configured and set automatically by the network’s DHCP server; If DHCP is OFF, the five parameters below must be manually configured as needed

Server/Client Sub-menu

Table 3-18. IO Module EtherNet Menu Parameters

40 Visit our website www.RiceLake.com

Page 47

Configuration

Menu Description

Server Timeout The connection is closed if there is no activity before the set time - 0 disables the inactivity disconnect. Enter value: 0-

65535 seconds, 0 (default)

Stream Format Specifies the stream format used for streaming output of scale data (Trigger=Stream Legal for Trade or Stream industrial)

or specifies the expected input for a serial scale (Trigger=REMOTE). Server Echo Specifies whether characters received by the port are echoed back to the sending unit; Settings: OFF (default), ON Server Response Specifies whether the port transmits replies to serial commands; Settings: ON (default), OFF

NOTE: If an external device (such as a printer), that may transmit unexpected data (such as a paper low message),

is connected to the 882IS the response parameter should be set to OFF to prevent a reply from the 882IS from

confusing the external device.

Client Remote Port Client only: the TCP port number of the remote server of the IO module is connecting to; Enter value: 1-65535, 1 (default) Client Trigger Select the operation of the port; Settings:

COMMAND (default) – allows operation of EDP commands and will print STRIND – stream industrial scale – data is transmitted up to the configured A/D sample rate; Will also accept EDP

STRLFT – stream legal for trade scale data is transmitted at the configured display update rate; Will also accept EDP

Termination Selects the termination character(s) for data sent from the port; Settings: CR/LF (default), CR Client End of Line Delay Specifies the delay between transmitted lines of data, in 0.1 second intervals; Enter value: 0-255, 0 (default) Client Timeout Connection is closed if there is no activity before the set time; 0 disables the inactivity disconnect;

Enter value: 0-65535 (seconds), 0 (default)

Client Stream Format Specifies the client stream format used for streaming output of scale data (Trigger=Stream Legal for Trade or Stream

industrial) or specifies the expected input for a serial scale (Trigger=REMOTE). Client Echo Specifies whether characters received by the port are echoed back to the sending unit; Settings: OFF (default), ON Client Response Specifies whether the port transmits replies to serial commands; Settings: ON (default), OFF

NOTE: If an external device (such as a printer), that may transmit unexpected data (such as a paper low message),

is connected to the 882IS the response parameter should be set to OFF to prevent a reply from the 882IS from

confusing the external device.

commands and printing

Table 3-18. IO Module EtherNet Menu Parameters (Continued)

Page 48

882IS/882IS Plus

IO Option Card

Setup

IO Module

Fieldbus Card

Fieldbus Swap

Mode

Minimum Value

Analog Output

Output Error Action

Minimum Negative

Maximum Value

Maximum Negative

Calibrate Zero Calibrate Span

DeviceNet Address

Profibus Address

IO Module - Option Card

Figure 3-21. IO Module Option Card Menu Structure

Menu Choice Description

Fieldbus Card Fieldbus Swap

DeviceNet Address Profibus Address

Analog Output Mode Mode – specifies the weight data tracked by the analog output; Settings: GROSS (default), NET

Output 1-10V 0-20mA 4-20mA

Error Action Error Action – specifies how the analog output responds to system error conditions; Settings:

Minimum Value Specifies the minimum weight value tracked by the analog output; enter value: 0–9999999, 000000 (default) Minimum Negative Specify ON if the minimum weight (MIN parameter) is a negative value; Settings: OFF (default), ON Maximum Value Specifies the maximum weight value tracked by the analog output; Enter value: 0–9999999, 10000 (default) Maximum Negative Specify ON if the maximum weight (MAX parameter) is a negative value; Settings: OFF (default), ON Calibrate Zero Calibrate Zero – edit the value to match the reading on the multimeter to perform a calibration Calibrate Span Calibrate Span – edit the value to match the reading on the multimeter to perform a calibration

Specifies byte-swapping used for the fieldbus card; Settings: NONE, BYTE, BOTH (Default for DeviceNet is BYTE; default for all other cards is NONE) Is the address given to a DeviceNet option card. Range 1-64, 63 (default) Is the address given to a Profibus option card. Range 1-126, 126 (default)

Selects whether the analog output supplies voltage (0-10 V - default), current (0-20mA) or current (4-20mA).

• FULLSC (default) – set to full value (10 V or 20 mA)

• HOLD – hold current value

• ZEROSC – set to zero value (0 V or 4 mA)

Table 3-19. IO Module Analog Output Option Card Menu Parameters

42 Visit our website www.RiceLake.com

Page 49

Configuration

Power Saving

Mode

Setup

Wake

Threshold

Backlight

Control

Battery

Installed

Version

Software

Setup

Regulation Default

3.2.17 Power Savings Menu

Figure 3-22. Power Savings Structure

Menu Choices Description

Level 2 submenus

Power Saving Mode Off

Light Medium Aggressive

Wake Threshold 0.0 - 9999999.0 Once asleep, if the primary weight goes above the value, the indicator wakes. A value of 0 prevents the indi-

Backlight Control On

Off

Battery Installed No

Yes

No power saving performed Turns off backlight Turns off backlight and blanks the display Turns off backlight, blanks the display and turns off the excitation If configured for NTEP and the Power Savings Mode is set to aggressive; a weight change will not wake the indicator. Only a key press or receipt of serial data will wake the indicator from NTEP Aggressive

cator from waking due to a weight change. Only a keypress or serial command will wake the unit. Manually controls whether the backlight is on or off

Manually controls whether the indicator is being powered by a battery. Power saving functionality is only activated if the battery installed is set to yes

Table 3-20. Power Savings Menu Parameters

3.2.18 Version Menu

The Version menu is used to check the firmware version installed in the indicator and set the indicator configuration to factory defaults.

Figure 3-23. Version Menu Structure

Menu Choices Description

Software VX.XX.XX Displays firmware version number Regulation LVR X.XX Displays the Legally Relevant firmware version number Default No

Yes

Performs a reset of all the indicator parameters to factory default settings

IMPORTANT All configuration and load cell calibration data will be lost.

Table 3-21. Version Menu Parameters

Page 50

882IS/882IS Plus

Keypad Test

Test

Battery Counts

Key Text

Integer

Time

Time & Date

Date

000000

View

Accumulator

Clear

Accumulator

Tare Value

Tare

3.3 Test Menu

Figure 3-24. Test Menu Structure

Menu Choices Description

Keypad Test -- Allows the 882IS and 882IS Plus keypad to be tested. Key presses are displayed and also transmitted on the COM port Battery Counts 35064 (5.8V

= 3/4 charge after barrier)

View the current battery voltage as counts. The value shown at left is approximate. Expect the voltage to drop as it passes through the protection barrier. The count value is an estimate of the battery voltage as measured at J3 (after the protection barrier) and is therefore not equal to the true battery voltage as measured at the battery terminals (inside the sealed battery box).

Table 3-22. Test Menu Parameters

3.4 Time and Date

3.5 Accumulator Menu

Menu Choices Description

View -- Views the current accumulator value, if enabled Clear Accumulator -- Clears the current accumulator value, if enabled

3.6 Tare

Figure 3-25. Time and Date Menu Structure

Menu Choices Description

Time -- View or set the time Date -- View or set the date

Table 3-23. Time and Date Menu Parameters

Figure 3-26. Accumulator Menu Structure

Table 3-24. Accumulator Menu Parameters

Figure 3-27. Tare Menu Structure

Menu Choice Description

Tare -- Views the current tare value

Table 3-25. Tare Menu Parameter

44 Visit our website www.RiceLake.com

Page 51

4.0 Calibration

Note

Scale

Calibrate

Zero Calibration

Setup

Test Weight

Count Value Count Value Point 1 - 5 Count Value

Calibrate

Span Calibration

Linear Calibration

Rezero Last Zero

Temporary Zero

Count Value

Calibrate

Count Value

Calibrate

Decimal

Calibrate

Calibration

Point 1

Weigh Point 1

Decimal

Count Value

Calibrate

TAR E

Note

TAR E

Note

The 882IS can be calibrated using the front panel, EDP commands, or Revolution configuration utility. Calibration consists of the following steps:

• Zero calibration

• Entering the test weight value

• Span calibration

• Optional five-point linearization

• Optional rezero calibration for test weights using hooks or chains

• Optional last zero calibration

• Optional temporary zero calibration

The 882IS requires the Zero Calibration and Span Calibration to be calibrated. The linearity points are optional; they must fall between zero and span, but must not duplicate zero or span. During calibration, Tare acts as a data entry confirmation key. It also acts as an Enter key, and accepts the value if calibration was successful

Calibration

Figure 4-1. Calibration Menu

4.1 Front Panel Calibration

1. Put the indicator in setup mode, see Figure 3-1 on page 23, (or use if audit trail is enabled), and navigate to

Calibrate (see Figure 4-1).

2. Press or to go to the

Zero Calibration is used for most normal calibrations with an empty scale. If a special situation exists, where a Last Zero or Temporary Zero are used, refer to Section 4.2 or Section 4.3 for more information before performing a Zero Calibration.

3. Press or to view the previously captured A/D count value for zero.

Remove all weight from the scale. If the test weights require hooks or chains, place the hooks or chains on the scale

for zero calibration.

Press to perform zero calibration.

Press to leave without performing a calibration.

Zero Calibration parameter.

Page 52

882IS/882IS Plus

Note

TAR E

Note

TAR E

Note

TAR E

6. The indicator displays

Calibrating, Please Wait

while calibration is in progress. When complete,

To view the new zero A/D count, press then repeat Step 3, but instead of pressing Enter while viewing the

value, press to exit.

7. With Test Weight displayed, press to display the stored calibration weight value.

8. Edit the value using the keypad on the 882IS Plus or the numeric entry method for the 882IS.

• Press or to select the digit

• Press or to increment or decrement the value

• press when the value is correct

• Press or to move the decimal point position

9. Press to store the

10. With

Span Calibration displayed, press or to view the previously captured A/D count value for span.

Test Weight value and advance to Span Calibration.

11. Place calibration weights on the scale equal to test weight value.

12. Press to perform span calibration.

If calibration of span is not required, press to exit.

Test Weight

displays.

13. Press the indicator displays Calibrating, Please Wait while calibration is in progress. When complete, Linear

Calibration

displays.

To view the new span A/D count, press then repeat Step 9, but instead of pressing Enter while viewing the

value, press Menu to exit.

14. Press when calibration is complete, to return to weigh mode.

4.1.1 Five-Point Linearization

Five-point linearization (using the Linear Calibration parameter) provides increased scale accuracy by calibrating the indicator at up to five additional points between the zero and span calibrations. Linearization is optional: if choosing not to perform linearization, skip the to zero during zero calibration. To perform linearization, follow the procedure below.

Linear Calibration points must be less than the Span Calibration point.

1. With Linear Calibration displayed, press ,Point-1 displays.

2. Press again,

3. Press to display the value of the weigh point.

4. Edit the value using the keypad on the 882IS Plus or the or the numeric entry method for the 882IS.

• Press or to select the digit

• Press or to increment or decrement the value

Linear Calibration parameter; if linearization values have previously been entered, these values are reset

Weigh Point 1 displays.

• Press when the value is correct (the decimal point will be set in the following step).

• Press or to move the decimal point position

46 Visit our website www.RiceLake.com

Page 53

Calibration

TAR E

Note

5. Press to confirm value. The indicator displays Calibration Point 1.

6. Place test weights on the scale and press . The indicator displays the previously captured A/D counts for the linearization point.

7. Press again to calibrate. The indicator displays complete,

8. Press to

Weight Point 1 is displayed.

Point-1, then press to Point-2.

9. Repeat for up to five linearization points. To exit the linearization parameters, press to return to

Calibrating, Please Wait while calibration is in progress. When

Linear Calibration.

10. Press when calibration is complete, to return to the weigh mode.

4.1.2 Rezero

The rezero function is used to remove a calibration offset when an apparatus is used to hang the test weights. If no chains or hooks were used to hang the test weights during calibration, remove the test weights and press to return to the menu.

1. With

Rezero displayed, press or to access the rezero function.

Remove all weight from the scale. If the test weights require hooks or chains, place the hooks or chains on the scale

for zero calibration. The indicator displays the AD count from the previous zero calibration.

3. With all weight removed, press to rezero the scale. This function acquires a new ZERO calibration value. The indicator displays

Zero displays.

For more information on LAST or TEMP see Section 4.2 or Section 4.3.

Calibrating, Please Wait while the zero and span calibrations are adjusted. When complete, Last

Calibrate

4. Press to return to weigh mode.

4.2 Last Zero

Last zero (typically platform scales) replaces the original captured zero with the last push button zero prior to a calibration and does not need to remove the test weights.

To use this feature a pushbutton zero must have been taken while the scale was empty while in the weigh mode.

Perform a normal calibration, except instead of using Zero Calibration to capture the zero point of an empty scale, select Last

to use the last pushbutton zero. The test weight does not need to be removed from the scale.

Zero

4.3 Temporary Zero

Temporary zero (typically tank scales) is only a reference for a span calibration, and allows the original zero to be retained after a span adjustment has been done.

This procedure assumes the previously calibrated zero point is still accurate.

Perform a normal calibration, except instead of using Zero Calibration to capture the zero point of an empty scale, select

Temporary Zero. After calibrating the temporary zero, enter into Test Weight the value of the test weights added to the scale (just

the test weights, not the product loaded on the scale). Then perform the span calibration.

4.4 Adjusting Final Calibration (Trimming)

Calibration may be affected by environmental factors including wind, vibration, and angular loading. For example, if the scale is calibrated with 1000 lb, a strain test may determine that at 2000 lb the calibration is 3 lb high. In this case, final calibration can be adjusted by changing the test weight to 998.5 lb. This adjustment provides a linear correction of 1.5 lb per 1000 lb.

Page 54

882IS/882IS Plus

Note

4.5 Gravity Compensation

This feature is used to compensate for the variance in gravitational pull from one location to another. To calibrate with gravity compensation, the Gravity Compensation parameter under the

Features menu must be set to ON (see Section 3.2.7 on

page 30), and the Latitude and Elevation (elevation in meters, relative to sea level) parameters set before calibrating the

indicator. If the indicator is later installed at a different location, gravity compensation can be applied to a pre-calibrated indicator by

adjusting the Latitude and Elevation parameters.

4.6 EDP Command Calibration

To calibrate the indicator using EDP commands an indicator or IO Module port must be connected to a terminal or personal computer. See Section 2.5 on page 14 for cable connections.

The indicator will respond with OK if the value of the parameter was valid, or the command executed properly. If the indicator responds with ??, then either the value for the parameter was invalid, or the command could not be executed

Once the indicator is connected to the sending device, do the following:

1. Place the indicator in setup mode and remove all weight from the scale platform. If the test weights require hooks or chains, place the hooks or chains on the scale for zero calibration.

2. Send the SC.WZERO#1 command to calibrate zero. The indicator displays in progress.

3. Place test weights on the scale and use the SC.WVAL#1 command to enter the test weight value in the following format:

SC.WVAL#1=nnnnnn<CR>

4. Send the SC.WSPAN#1 command to calibrate span. The indicator displays Calibrating, Please Wait while calibration is in progress.

5. Up to five linearization points can be calibrated between the zero and span calibration values. Use the following commands to set and calibrate a single linearization point:

SC.WLIN.V1#1=nnnnn<CR> SC.WLIN.C1#1<CR>

The SC.WLIN.V1#1 command sets the test weight value (nnnnn) for linearization point 1. The SC.WLIN.C1#1 command calibrates the point. Repeat using the SC.WLIN.Vn#1 and SC.WLIN.Cn#1 (where 'n' is the linearity point number) commands as required for additional linearization points.

6. To remove an offset value, clear all weight from the scale, including hooks or chains used to hang test weights, then send the SC.REZERO#1 command. The indicator displays

Calibrating, Please Wait while the zero and span

calibrations are adjusted.

7. Send the KMENU or KEXIT EDP command to return to weigh mode.

Calibrating, Please Wait while calibration is

48 Visit our website www.RiceLake.com

Page 55

Calibration

4.7 Revolution® Calibration

To calibrate the indicator using Revolution, an indicator port must be connected to a PC running the Revolution configuration utility.

1. Place the indicator in configuration mode (display reads from the scale platform.

2. From Revolution, select

Select Indicator dialog box appears.

The

File » New.

3. Select 882IS module which matches the firmware of the indicator and click

4. From the Communications menu, select

Connect.

5. From the left pane, expand the Scale selection and select the Scale button.

6. From the Tools menu, select

7. Select

Next to begin the Calibration Wizard.

Calibration Wizard.

8. Select whether or not to perform a standard calibration or a standard with multi-point linearization and select

Next.

9. In the text box, enter the test weight value be to used for span calibration.

10. Select the check box if using chains or hooks during the calibration, then select

11. Remove all weight from the scale and select

Click to Calibrate Zero to begin zero calibration. If the test weights require

an apparatus to hang, place it on the scale for zero calibration.

12. When zero calibration is complete, the Calibration Wizard prompts to place test weights on the scale. Place the test weights on the scale, then select

Click to Calibrate Span.

13. If choosing to perform linear calibration, the Calibration Wizard now displays prompts (1–5). Enter the weight value for Linear Point #1, place test weights on scale and select

Next.

14. If the check box for using chains or hooks is selected, the Calibration Wizard prompts to perform a Re-zero. Remove the apparatus used to hang the weights, and select

15. With the weights removed, the new and old calibration settings are displayed. To accept the new values, select To exit and restore the old values, select

Cancel.

Scale) and remove all weight

OK.

Figure 4-2. Scale Button

Next.

Measure. Repeat for additional linearization points, then select

Click to Calibrate Re-Zero.

Finish.

Page 56

882IS/882IS Plus

Note

5.0 Using Revolution

The Revolution utility provides functions used to support configuration, calibration, customizing and backup of the 882IS configuration settings using a PC.

Calibration values, scale configuration and print ticket formatting can be configured, saved and restored to the 882IS using Revolution.

The indicator’s operating firmware can also be updated using Revolution.

For system requirements visit the Rice Lake Weighing Systems website.

5.1 Communication With the Indicator

Communicating to the 882IS can be accomplished in the following ways:

• Using a serial connection to the indicator serial (COM) port through J3

• Using a USB connection and Virtual Comm Port to the indicator’s USB Micro Device (USBCOM) port through J4

• Using a TCP/IP connection through the Ethernet Port (J6)

After making the physical connection to a PC, select the Options in the Tools menu and configure the communications settings as needed to match the communications method that is being used:

• RS-422 – Select the COM port that it will be connected to. Settings can be configured manually to match the indicator's

current settings, or check the box for “Auto Detect Settings” to have Revolution automatically detect the settings.

• USB – Select RS-422 as the communication mode, the USB connection appears as a standard COM port to Revolution.

Note that the comm port for the USB connection will only show in the list of available ports if the indicator is physically connected, and powered on. The settings for baud rate, data and stop bits, and parity do not apply for a USB connection, and do not need to be set to any specific value.

• TCP/IP – Requires the IP address and TCP Port of the indicator. Enter the IP Address and Port during the

communications connection.

To open the communication connection, click on Connect under the Communications menu, or the Connect button in the toolbar. Revolution will attempt to establish communications with the indicator.

If Revolution does not detect the indicator, check the:

Physical connections

Communications settings in Revolution

Current settings of the communications port in the indicator

Indicator communications port Trigger parameter is set to Command

If Revolution displays a Version Error, the indicator version of firmware does not match the module used in Revolution. A connection can be forced, but some parameters may not be enabled if they were not originally supported in that module.

50 Visit our website www.RiceLake.com

Page 57

Using Revolution®

5.2 Configuration

The Revolution configuration utility provides the preferred method for configuring the 882IS indicator. Revolution runs on a PC to set configuration parameters for the indicator. When Revolution configuration is complete, configuration data is downloaded to the indicator.

5.2.1 New Configuration File

1. Select New File on the toolbar (NEW under the file menu can also be used).

Figure 5-1. Revolution Main Screen

2. Select the icon for the indicator with the appropriate firmware version for which the configuration file is to be created.

3. Revolution will create a default configuration file. Edit the settings, upload the indicator’s current settings, or download the default settings to the indicator.

5.2.2 Open an Existing Configuration File

1. Select Open File on the tool bar (Open under the file menu can also be used).

2. Navigate to the *.rev file to open then click the

3. Revolution opens the file, selecting the correct indicator module to use with it. Edit the settings, or download the settings to the indicator.

OK button.

5.2.3 Saving a Configuration File

1. Select Save File on the tool bar (Save under the file menu can also be used).

• If the file is new, enter a name when requested.

• If the file already exists, confirm to overwrite the previous file.

• Select cancel to exit the save process without saving.

• Select Save As under the file menu if saving to a different file name.

Downloading to the Indicator

The Download Configuration function on the Revolution Communications menu allows a Revolution configuration file (with or without scale calibration data), ticket formatsto be downloaded to a connected indicator in configuration mode.

The Download Section function on the Communications menu allows download of only the currently displayed section, such as the communications port configuration.

Because less data is transferred using Download Section, it is typically faster than a full configuration download, but there is an increased possibility that the download may fail due to dependencies on other objects. If the download fails, try performing a complete download using the Download Configuration function.

Page 58

882IS/882IS Plus

Uploading Configuration to Revolution

The Upload Configuration function on the Revolution Communications menu allows the existing configuration of a connected indicator to be saved to a file on the PC. Once saved, the configuration file provides a backup that can be quickly restored to the indicator if needed. Or, the file can be edited within Revolution and downloaded back to the indicator.

5.3 Revolution Help

The menu bar in Revolution contains a Help system for further assistance in using Revolution software. The Help system contains an index of help topics and a search function. The search function allows the user to search with a

keyword. When a keyword is typed into the search text box, Help searches its Index and finds the closest related topic in the help system.

52 Visit our website www.RiceLake.com

Page 59

EDP Commands

6.0 EDP Commands

The 882IS indicator can be controlled by a personal computer or terminal using the EDP commands, which can simulate front panel key press functions, display and change setup parameters, and perform reporting functions.

6.1 The EDP Command Set

The EDP command set can be divided into seven groups: key press commands, reporting commands, the

RESETCONFIGURATION special function command, parameter setting commands, weigh mode commands, error conditions

commands. When the indicator processes an EDP command, it responds with the message OK. The OK response verifies that the

command was received and has been executed. If the command is unrecognized or cannot be executed, the indicator responds with ??.

The following sections list the commands and command syntax used for each of these groups.

6.1.1 Key Press Commands

Key press EDP commands (Table 6-1) simulate pressing the keys on the front panel of the indicator. These commands can be used in both setup and weighing mode. Several of the commands serve as “pseudo” keys, providing functions that are not represented by a key on the front panel.

For example, to enter a 15-pound tare weight using EDP commands:

1. Type K1 and press

2. Type K5 and press

3. Type KTARE and press

Enter (or RETURN). Enter.

Enter.

Command Function

KMENU Press the Menu key KZERO Press the Zero key KUNITS Press the Units key KPRINT Press the Print key KTARE Press the Tare key KGROSSNET Press the Gross/Net key KGROSS Go to gross mode KNET Go to net mode KDISPACCUM Display ACCUM (pseudo key) KDISPTARE Display tare (pseudo key) KCLR Press the Clear key (pseudo key) KCLRTAR Clear tare from system (pseudo key) KLEFT In menu mode, move left in the menu KRIGHT In menu mode, move right in the menu KUP In menu mode, move up in the menu KDOWN In menu mode, move down in the menu

KSAVE

KEXIT

K0–K9 Press number 0 (zero) through 9

In menu mode, saves the current configuration (pseudo key)

In menu mode, saves the current configuration then exits to weigh mode (pseudo key)

Command Function

KDOT Press the decimal point (.) KENTER Press the Enter key (pseudo key)

KLOCK

KUNLOCK

KESCAPE

KPRIM Change to primary units (pseudo key) KSEC Change to secondary units (pseudo key)

Lock specified front panel key. For example, to lock the Zero key, enter KLOCK=KZERO. (pseudo key)

Unlock specified front panel key. For example, to unlock the Print key, enter KUNLOCK=KPRINT. (pseudo key)

Exits the selected parameter. Returns to weigh mode if a parameter is not selected (functions identical to the Menu key in menu mode) (pseudo key)

Table 6-1. EDP Key Press Commands

Page 60

882IS/882IS Plus

Note

6.1.2 Reporting Commands

Reporting commands (Table 6-2) send specific information to the EDP port. These commands can be used in both configuration mode and weigh mode.

Command Function

AUDITJUMPER

BUILD Returns the date and time of the software build DUMPALL Returns a list of all parameter values DUMPAUDIT Returns a list of audit trail information DUMPETH Returns a list of all parameter values pertaining to the EtherNet VERSION Returns the 882IS firmware version P Returns the current displayed weight with units identifier IOMODULEVERSION Returns the IO module firmware version, if attached. If no IO module is attached/detected, NONE is returned

Returns the state of the audit jumper. A response of A response of “??” indicates the jumper is in the

Table 6-2. EDP Reporting Commands

OK indicates the jumper is in the On position.

Off position

6.1.3 The RESETCONFIGURATION Command

The RESETCONFIGURATION command can be used in configuration mode to restore all configuration parameters to their default values.

This command is equivalent to using the DEFAULT function in configuration mode.

All load cell calibration settings are lost when the RESETCONFIGURATION command is run.

6.1.4 Parameter Setting Commands

Parameter setting commands allow the display or change of the current value for a particular configuration parameter (Tables 6-

3 through 6-22).

Current configuration parameter settings can be displayed in either configuration mode or weigh mode using the following syntax:

command

Most parameter values can be changed in configuration mode only. Use the following command syntax when changing parameter values:

command

where value is the new value you want to assign to the parameter. Use no spaces before or after the equal (=) sign. If an incorrect command has been typed in, the response will be ??.

For example, to set the motion band parameter to 5, type the following:

SC.MOTBAND#1

For parameters with selectable values, enter the command and equal sign followed by a question mark:

command

to see a list of those values. The indicator must be in configuration mode to use this function.

<CR>

=value<CR>

=5D<CR>

=?<CR>

54 Visit our website www.RiceLake.com

Page 61

EDP Commands

6.1.5 Scales Menu

Command Menu Description Choices / Range

SC.ACCUM#1 Accumulator Accumulator of weighments OFF, ON SC.DFTHRH#1 Digital Filter Threshold Digital filter cutoff threshold 0-99999 SC.DSPRATE#1 Display Update Rate Display Update Rate (in 0.1 sec intervals) 1-80 SC.DFSENS#1 Digital Filter Sensitivity Digital filter cutoff sensitivity LIGHT,MEDIUM,HEAVY SC.GRADS#1 Graduations Graduations to determine capacity 1 - 100000 SC.MOTBAND#1 Motion Band Motion Band (in display divisions) 0-100 SC.OVRLOAD#1 Overload Overload point based on capacity SC.OVRLOAD_VAL#1 Enter Percentage Overload point based on percentage of capacity 0.0 - 150.0 SC.PWRUPMD#1 Powerup Mode Power Up Mode GO, DELAY SC.RANGE1.MAX#1 Range-1 Max Maximum weight for first range or interval 0.0 - 999999.0 SC.RANGE2.MAX#1 Range-2 Max Maximum weight for second range or interval 0.0 - 999999.0 SC.RANGE3.MAX#1 Range-3 Max Maximum weight for third range or interval 0.0 - 999999.0

SC.SMPRAT#1 Sample Rate Scale Sample Rate

SC.SPLIT#1 Multi Ranges Specifies full range, multi-range, or multi-interval OFF, 2RNG, 3RNG, 2INTVL, 3INTVL SC.SSTIME#1 Standstill Time Stand still time (in 0.1 sec intervals) 1 - 65535 SC.TAREFN#1 Tare Function Tare Function BOTH, NOTARE, PBTARE, KEYED SC.THRESH#1 Accumulator Threshold Accumulator Zero Threshold 0-999999 SC.ZRANGE#1 Zero Range Zero range (in %) 0.0 - 100.0 SC.ZTRKBND#1 Zero Track Band Zero track band (in divisions) 0.0 - 100.0

Table 6-3. Scale EDP Commands

FS+2%, FS+1D, FS+9D, FS

7.5HZ, 15HZ, 30HZ, 60HZ, 120HZ, 240HZ, 480HZ, 960HZ

6.1.6 Format Menu

Command Menu Description Choices / Range

If SPLIT = 2RNG, 3RNG, 2INTVL, 3INTVL SC.PRI.DECPNT#1 DP Location-1 Decimal point location for first range or interval 888888, 888880, 8.88888, 88.8888, 888.888,

8888.88, 88888.8

SC.SEC.DECPNT#1 DP Location-2 Decimal point location for second range or interval 888888, 888880, 8.88888, 88.8888, 888.888,

8888.88, 88888.8

SC.TER.DECPNT#1 DP Location-3 Decimal point location for third range or interval. Only avail-

able in 3RNG or 3INTVL SC.PRI.DSPDIV#1 Range-1 DD Range/Interval (1 division size) 1D, 2D, 5D SC.SEC.DSPDIV#1 Range-2 DD Range/Interval (2 division size) 1D, 2D, 5D SC.TER.DSPDIV#1 Range-3 DD Range/Interval (3 division size)

Only available in 3RNG or 3INTVL. If SPLIT = OFF SC.PRI.UNITS#1 Primary Units Specifies primary units for displayed and printed weight LB, KG, OZ, TN, T, G, NONE SC.SEC.UNITS#1 Secondary Units Specifies secondary units for displayed and printed weight LB, KG, OZ, TN, T, G, NONE

Table 6-4. Format EDP Commands

888888, 888880, 8.88888, 88.8888, 888.888,

8888.88, 88888.8

1D, 2D, 5D

Page 62

882IS/882IS Plus

Note

6.1.7 Calibration Menu

Command Menu Description Choices / Range

SC.WZERO#1 Calibrate Zero Perform zero calibration n/a SC.WSPAN#1 Calibrate Span Perform span calibration n/a SC.LC.CD#1 Zero Counts Get/Set Calibration Zero value -8388607 to 8388607 SC.LC.CW#1 Gain Counts Get/Set Calibration Gain value -8388607 to 8388607 SC.LC.CZ#1 Zero Counts Get/Set Calibration Zero value -2147483646 to 2147483647 SC.REZERO#1 Rezero Perform Calibration Re-Zero n/a SC.WLIN.C1#1 Calibration Point - 1 Calibrate linearization point 1 n/a SC.WLIN.C2#1 Calibration Point - 2 Calibrate linearization point 2 n/a SC.WLIN.C3#1 Calibration Point - 3 Calibrate linearization point 3 n/a SC.WLIN.C4#1 Calibration Point - 4 Calibrate linearization point 4 n/a SC.WLIN.C5#1 Calibration Point - 5 Calibrate linearization point 5 n/a SC.WLIN.F1#1 MultiPoint Cal-1 Raw count value for linearization point 1 -2147483646 to 2147483647 SC.WLIN.F2#1 MultiPoint Cal-2 Raw count value for linearization point 2 -2147483646 to 2147483647 SC.WLIN.F3#1 MultiPoint Cal-3 Raw count value for linearization point 3 -2147483646 to 2147483647 SC.WLIN.F4#1 MultiPoint Cal-4 Raw count value for linearization point 4 -2147483646 to 2147483647 SC.WLIN.F5#1 MultiPoint Cal-5 Raw count value for linearization point 5 -2147483646 to 2147483647 SC.WLIN.V1#1 Cal Point-1 Weight Test weight value for linearization point 1 0.0 - 999999.0 SC.WLIN.V2#1 Cal Point-2 Weight Test weight value for linearization point 2 0.0 - 999999.0 SC.WLIN.V3#1 Cal Point-3 Weight Test weight value for linearization point 3 0.0 - 999999.0 SC.WLIN.V4#1 Cal Point-4 Weight Test weight value for linearization point 4 0.0 - 999999.0 SC.WLIN.V5#1 Cal Point-5 Weight Test weight value for linearization point 5 0.0 - 999999.0 SC.WVAL#1 Test Weight Test weight value for standard gain calibration 0.00001 - 999999.0

Table 6-5. Calibration EDP Commands

The menu items, CAL1 – CAL5 are used to do the calibration. A value cannot be keyed in. The SC.WLIN.Fx#1 EDP commands can be used to view and edit the value but they do not perform the calibration. Use the SC.WLIN.Cx#1 commands to perform the calibration.

6.1.8 Ports COM Menu

Command Menu Description Choices / Range

EDP.BAUD#1 Baud Port baud rate *1200, *2400, *4800, 9600, 19200,

28800, 38400, 57600, 115200

*not available on port 3 EDP.BITS#1 Bits Port data bits and parity 8NONE, 7EVEN, 7ODD EDP.ECHO#1 Echo Specifies whether characters received by the port are

echoed back to the sending unit EDP.EOLDLY#1 End of Line Delay Port end-of-line delay in 0.1 sec intervals Range: 0 - 255 EDP.TYPE#1 Type Specifies RS-232 or RS-422 communication 232, 422 EDP.PRNMSG#1 Print Message Print message OFF, ON EDP.RESPONSE#1 Response Response OFF, ON EDP.SFMT#1 Stream Format Stream format Alphanumeric, max Length: 200 EDP.STOPBITS#1 Stop Bits Stop Bits 1, 2 EDP.TERMIN#1 Termination Termination character CR/LF, CR EDP.TRIGGER#1 Trigger Selects the operation of the port COMAND, STRLFT, STRIND, REMOTE

Table 6-6. Ports (COM) EDP Commands

OFF, ON

56 Visit our website www.RiceLake.com

Page 63

EDP Commands

6.1.9 Stream Tokens Menu

Command Description Default Choices / Range

STR.GROSS String transmitted for the <M> token for gross weight G Alphanumeric, Max Length: 8 STR.INVALID String transmitted for the <S> token when weight is invalid I Alphanumeric, Max Length: 2 STR.MOTION String transmitted for the <S> token when scale is in motion M Alphanumeric, Max Length: 2 STR.NEG Character transmitted for the <P> token when the weight is negative - NONE, SPACE, STR.NET String transmitted for the <M> token for net weight N Alphanumeric, Max Length: 8 STR.OK String transmitted for the <S> token when the scale is ok “ “ Alphanumeric, Max Length: 2 STR.POS Character transmitted for the <P> token when the weight is positive SPACE NONE, SPACE, + STR.PRI String transmitted for the <U> token for primary units L Alphanumeric, Max Length: 8 STR.RANGE String transmitted for the <S> token when the scale is out of range O Alphanumeric, Max Length: 2 STR.SEC String transmitted for the <U> token for secondary units K Alphanumeric, Max Length: 8 STR.TARE String transmitted for the <M> token for tare weight T Alphanumeric, Max Length: 8 STR.ZERO String transmitted for the <S> token when the scale is at center of zero Z Alphanumeric, Max Length: 2

Table 6-7. Stream Tokens EDP Commands

6.1.10 Feature Menu

Command Menu Description Choices / Range

DATEFMT Date Format Date Format MMDDYY, DDMMYY, YYMMDD, YYDDMM, MMDDY4, DDM-

MY4, Y4MMDD, Y4DDMM DECFMT Decimal Format Decimal Format DOT, COMMA GRAVADJ Gravity Adjust Must be enabled for latitude and elevation OFF, ON LAT.LOC Latitude Latitude (Gravity adjust must be set to ON) 0-90 ELEV.LOC Elevation Elevation (Gravity adust must be set to ON) -9999-9999 UID Unit ID Unit Identifier Alphanumeric, Max Length: 6

Table 6-8. Feature EDP Commands

6.1.11 Regulatory Menu

Command Menu Description Choices / Range

REGWORD Regulatory Word Term printed when weighing in gross mode GROSS, BRUTTO REGULAT Regulatory Regulatory agency having jurisdiction over the scale site NONE, OIML, NTEP, CANADA, INDUST REG.AGENCY Audit Agency Audit trail agency format NONE, OIML, NTEP, CANADA

Zero preference for overload calculation

REG.BASE Overload Base

REG.CTARE Clear Tare CLEAR key – clear tare/accumulator while viewing NO, YES REG.RTARE Round Tare Round push button tare to nearest Display Division. YES,NO REG.KTARE Keyed Tare Keyed tare NO, YES REG.MTARE Multiple Tare Action Multiple tare action NOTHIN, REPLAC, REMOVE REG.NTARE Negative Tare Negative or zero tare NO, YES REG.PRTMOT Print Motion Print while in motion NO, YES REG.PRINTPT Add PT to Print Add “PT” to keyed tare print NO, YES REG.SNPSHOT Select Weight Source Selects display or scale weight source DISPLAY, SCALE REG.ZTARE Zero Tare Remove tare on ZERO NO, YES

CALIB - Calibrated zero SCALE - Pushbutton zero

Table 6-9. Regulatory EDP Commands

CALIB, SCALE

Page 64

882IS/882IS Plus

Note

6.1.12 Passwords Menu

Command Menu Description Choices / Range

PWD.USER User Used to protect items in the top level menu Range: 0 - 999999 PWD.SETUP Setup Used to protect items in the setup menu Range: 0 - 999999

Table 6-10. Password EDP commands

The EDP commands can be used to set the passwords but they will not return the current password setting.

6.1.13 Keypad Lock Menu

Command Menu Description Choices / Range

KEYLCK.FUNCTION Function Keys Lock or unlocks the Function Keys LOCK, UNLOCK KEYLCK.GROSSNET Gross/Net KEYLCK.MENU Menu KEYLCK.NUMERIC Numeric Keypad Locks or unlocks the Numeric Keypad Keys LOCK, UNLOCK KEYLCK.PRINT Print KEYLCK.TARE Tare KEYLCK.UNITS Units KEYLCK.ZERO Zero

Locks or unlocks the Gross/Net Key Locks or unlocks the Menu Key

Locks or unlocks the Print Key Locks or unlocks the Tare Key Locks or unlocks the Units Key Locks or unlocks the Zero Key

Table 6-11. Keypad Lock EDP Commands

LOCK, UNLOCK LOCK, UNLOCK

LOCK, UNLOCK LOCK, UNLOCK LOCK, UNLOCK LOCK, UNLOCK

6.1.14 Print Format Menu

The Menu items (except for HDRFMT) are listed by the format and the sub-parameters.

Command Menu Description Choices / Range

ACC.FMT Accumulator | Format Accumulator enabled and displayed Alphanumeric, Max Length: 1000

ACC.PORT Accumulator | Port Accumulator print port

GFMT.FMT Gross Format | Format Weigh mode, no tare in system Alphanumeric, Max Length: 1000

GFMT.PORT Gross Format | Port Weigh mode, no tare in system, print port

HDRFMT1 Header Format Must be inserted into other print format Alphanumeric, Max Length: 300 NFMT.FMT Net Format | Format Weigh mode, tare in system Alphanumeric, Max Length: 1000

NFMT.PORT Net Format | Port Weigh mode, tare in system, print port

Table 6-12. Print Format EDP Commands

See Section 7.2 on page 63 for more detailed information on print format commands.

COM, FIBER, IOCOM, IOCOMUSB, ETHSERVER, ETHCLIENT, OFF

6.1.15 Digital I/O Configuration Menu

Command Menu Choices / Range

DIO.b#s BIT x OFF, PRINT, ZERO, TARE, UNITS, CLEAR, DSPACC, DSPTAR, NT/GRS, CLRCN, OUTPUT, KBDLOC, GROSS,

NET, PRIM, SEC, CLRTAR, CLRACC

Table 6-13. Digital I/O Configuration EDP Commands

Digital inputs and outputs are specified by bit number (b = 1 or 2) and slot number (s = 0).

58 Visit our website www.RiceLake.com

Page 65

EDP Commands

Note

6.1.16 Weigh Mode Commands

The weigh mode commands (Table 6-14) transmit data to a data communications port on demand. The SX, EX, and all the X weight retrieval commands are valid only in normal operating mode; all other commands are valid in either setup or weigh mode.

see Section 9.3 on page 69 for error command definitions.

Command Function

AT Acquire tare DISPLAYMSG#n Displays a message on the indicated line (n). Example: DISPLAYMSG#3=abc SX#1 Start serial port streaming. If port is configured to stream on port #3. (3=Ethernet Server) SX Start serial port streaming for the port receiving the command, if port is configured to stream. EX#1 Stop serial port streaming for the port receiving the command, if port is configured to stream. 1=COM, 2=FiberOptic EX Stop serial port streaming for the port receiving the command, if port is configured to stream. RS Reset system. This is a soft reset. Used to reset the indicator without resetting the configuration to the factory defaults. S Sends a single stream frame from the scale to the port in the format defined by the Stream Format parameter of the port receiving

the command. XA#1 Transmit accumulator value in displayed units for scale n XA Transmit accumulator value in displayed units for selected scale XAP#1 Transmit accumulator value in primary units for scale n XAS#1 Transmit accumulator value in secondary units for scale n XG#1 Transmit gross weight in displayed units for scale n XG Transmit gross weight in displayed units for selected scale XG2 Transmit gross weight in non-displayed units for selected scale XGP#1 Transmit gross weight in primary units for scale n XGS#1 Transmit gross weight in secondary units for scale n XN#1 Transmit net weight in displayed units for scale n XN Transmit net weight in displayed units for selected scale XN2 Transmit net weight in non-displayed units for selected scale XNP#1 Transmit net weight in primary units for scale n XNS#1 Transmit net weight in secondary units for scale n XT#1 Transmit tare weight in displayed units for scale n XT Transmit tare weight in displayed units for selected scale XT2 Transmit tare weight in non-displayed units for selected scale XTP#1 Transmit tare weight in primary units for scale n XTS#1 Transmit tare weight in secondary units for scale n XE Returns a decimal representation of any error conditions XEH Returns a hexadecimal representation of any error conditions

Table 6-14. Weigh Mode EDP Commands

The 882IS only supports one scale therefore X commands are displayed with a #1.

Page 66

882IS/882IS Plus

Note

6.1.17 Power Commands

Command Menu Description Choices/Range

BACKLIGHT Backlight Control Manual control of whether the backlight is ON or OFF OFF, ON BATTERYINSTALLED Battery Installed Manual control of whether the indicator is being powered by a

battery (yes) or not (no)

POWERSAVINGMODE Power Saving Mode Selects which type of automatic power saving is to be performed

after 30 seconds of no activity (scale motion, keypress, or serial command received). OFF=none, LIGHT=turns off backlight, MEDIUM=turns off backlight and display, AGGRESSIVE=turns off backlight, excitation and display

WAKETHRESHOLD Wake Threshold Once asleep, if the primary weight goes above this value the indi-

cator will wake. A value of 0 will prevent indicator from waking due to a weight change - only a keypress or serial command will wake the unit

NO, YES

OFF, LIGHT, MEDIUM, AGGRESSIVE

0.0 - 9999999.0

Table 6-15. Power EDP Commands

6.1.18 Setup Mode Commands

Command Menu Description Choice/Range

RESETCONFIGURATION Default Resets all configuration parameters to their default val-

ues and clears the scale calibration

Table 6-16. Setup Mode Commands

The RESETCONFIGURATION command can be used in configuration mode to restore all configuration parameters to their default values.

This command is equivalent to using the DEFAULT function in configuration mode.

All load cell calibration settings are lost when the RESETCONFIGURATION command is run.

6.1.19 Analog Output Parameters

Command Menu Description Choice/Range

ALG.ERRACT#n Error Action Specifies how the analog output responds to system

error conditions

ALG.MAX#n Maximum Value Specifies the maximum weight value tracked by the

analog output

ALG.MAXNEG#n Maximum Negative Specifies ON if the maximum weight (MAX parameter)

is a negative value

ALG.MIN#n Minimum Value Specifies the minimum weight value tracked by the

analog output

ALG.MINNEG#n Minimum Negative Specifies ON if the minimum weight (MIN parameter) is

a negative value

ALG.MODE#n Mode Specifies the weight data, Gross or Net, tracked by the

analog output

ALG.OUTPUT#n Output Specifies the output type: 0-10 V, 0-20 mA, or 4-20 mA

output NOTE: This parameter must be set before calibrating the analog output.

Table 6-17. Analog Output Parameters

FULLSC: Sets to full value (10 V or 20 mA) HOLD: Holds the last value ZEROSC: Sets to zero value (0 V or 4 mA)

0.000001 - 9999800.0

ON: The maximum valued is negative OFF: The maximum value is positive

0.0 - 9999800.0

ON: The minimum value is negative OFF: The minimum value is positive

GROSS: Tracks the gross weight NET: Tracks the net weight

0-10 V: 0-10 volt output 0-20 mA: 0-20 mA output 4-20 mA: 4-20 mA output

60 Visit our website www.RiceLake.com

Page 67

6.1.20 Analog Output Commands

Command Menu Description Choice/Range

ALG.ENTERSPANCAL#n n/a Enters the mode for calibrating the analog output span. This is

needed only if calibrating through EDP commands

ALG.EXITSPANCAL#n n/a Exits the mode for calibrating the analog output span. This is

needed only if calibrating through EDP commands. This must be done before the results of the calibration are implemented

ALG.ENTERZEROCAL#n n/a Enters the mode for calibrating the analog output span. This is

needed only if calibrating through EDP commands

ALG.EXITZEROCAL#n n/a Exits the mode for calibrating the analog output span. This is

needed only if calibrating through EDP commands. This must be done before the results of the calibration are implemented

ALG.SPAN#n Calibrate Span Enter the observed output value to calibrate the analog output

span. Use a multimeter to monitor the analog output value

ALG.ZERO Calibrate Zero Enter the observed output value to calibrate the analog output

zero. Use a multimeter to monitor the analog output value

OK or ??

0.0 - 30.0

Table 6-18. Analog Output Commands

6.1.21 Test Commands

Command Menu Description Choice/Range

BATTERYCOUNTS Battery Counts The A2D count value taken from the battery that is used as an

indicator of battery life

Table 6-19. Test Commands

32600 (5.45 V - critical error voltage) 36000 (6.05 V - fully charged battery) These count ranges are approximate

EDP Commands

Page 68

882IS/882IS Plus

7.0 Print Formatting

The 882IS provides four print formats. Formats Gross Format and Net Format will be printed based on the current mode of operation when the using the <H1> formatting token. The Accumulator Format is printed if the accumulator is enabled and the print key is pressed while viewing the accumulator value.

Each print format can be customized to include up to 1000 characters of information (300 for Header Format), such as company name and address. Use the indicator front panel (Print Format menu), EDP commands, or the Revolution

configuration utility to customize the print formats.

7.1 Print Formatting Tokens

Table 7-1 lists tokens that can be used to format the 882IS print formats. Tokens included in the format strings must be

enclosed between < and > delimiters. Any characters outside of the delimiters are printed as text. Text characters can include any ASCII character that can be printed by the output device.

Tokens Description

<G> Gross weight in displayed units (See notes 1 and 2 below)  <N> Net weight in displayed units (See notes 1 and 2)  <T> Tare weight in displayed units (See notes 1 and 2)  <A> Accumulated weight in displayed units  <AC> Number of accumulator event (5-digit counter)  <AT> Time of last accumulator event  <AD> Date of last accumulator event  <TI> Time  <DA> Date  <TD> Time and date  <UID> Unit ID number (See note 3)  <CN> Consecutive number (See note 3)  <H1> Ticket header (HDRFMT) 

<NLnn>

<nnn>

SPnn>

<SU>

<CR> Carriage return character  <LF> Line feed character 

NOTES:

1. Gross, net, and tare weights are 8 digits in length, including sign and decimal point, followed by a space and a one- to five-digit units identifier. Total field length with units identifier is 10-14 characters. Depending on what units are configured, the units identifier will be lb, kg, oz, tn, t, or g.

2. Gross, net, tare, and accumulator weights can be printed in any configured weight units by adding the following modifiers to the gross, net, tare, and accumulator weight commands: /P (primary units), /D (displayed units), /S (secondary units), /T (tertiary units). If not specified, the current displayed units (/D) is assumed. Example: To format a ticket to show net weight in secondary units, use the following command: <N/S>.

3. Unit ID and consecutive number (CN) fields are 1–6 characters in length, as required.

4. If nn is not specified, 1 is assumed. Value must be in the range 1–99.

5. After receiving an SU token, the indicator sends unformatted data until the next SU token is received. Unformatted data omits decimal points, leading and trailing characters.

New line ( ASCII character (

example) in the print stream. Space (nn = number of spaces) (See note 4) Toggle weight data format (formatted/unformatted)

(See note 5)

Print key is pressed (see Table 7-2 on page 63). Header Format can be inserted into any other print format

Ticket Format

Gross Format/Net Format/

Accumulator Format

nn = number of termination (<CR/LF> or <CR>) characters) (See note 4)

nnn = decimal value of ASCII character). Used for inserting control characters (STX, for



Table 7-1. Print Format Tokens

62 Visit our website www.RiceLake.com

Page 69

Print Formatting

7.2 Default Print Formats

Table 7-2 shows the default print formats for the 882IS and lists the conditions under which each print format is used.

Format Default Used When

GROSS FORMAT | FMT GROSS<G><NL2><TD><NL> Weigh mode, no tare in system GROSS FORMAT| PORT COM Defines the communication port that the format will be sent to.

NET FORMAT | FMT

NET FORMAT | PORT COM Defines the communication port that the format will be sent to. ACCUMULATOR FORMAT |

FORMAT ACCUMULATOR FORMAT |

PORT HEADER FORMAT | FORMAT COMPANY NAME<NL> STREET

GROSS<G><NL>TARE<SP><T><NL>NET<S P2><N><NL2><TD><NL>

ACCUM<A><NL><DA> <TI><NL> Accumulator enabled and displayed.

COM Defines the communication port that the format will be sent to.

ADDRESS<NL>CITY,ST ZIP<NL2>

NOTES: In OIML and CANADA modes, the letters PT (preset tare) are automatically inserted after the printed tare weight.

Weigh mode, tare in system

The Header Format is used to specify header information that can be used by the other print formats. The contents of the Header Format can be inserted into any other print format using the <H1> formatting token.

Table 7-2. Default Print Formats

Page 70

882IS/882IS Plus

Note

7.3 Customizing Print Formats

The following sections describe procedures for customizing print formats using the EDP commands, the front panel (Print Format menu), and the Revolution configuration utility.

7.3.1 Using the EDP Commands

With a personal computer, terminal, or remote keyboard attached to the 882IS, the EDP command set can be used to customize the print format strings.

To view the current setting of a format string, type the name of the print format, followed by .FMT, and press to check the current configuration of the Gross Format, type GFMT.FMT and press

Enter. The indicator responds by sending

the current configuration for the gross format:

GROSS<G><NL2><TD><NL>

To change the format, use the format EDP command followed by an equals sign (=) and the modified print format string. For example, to add the name and address of a company to the gross format, send the following EDP command:

GFMT.FMT=RICE LAKE WEIGHING SYSTEMS<NL>230 W COLEMAN ST<NL>RICE LAKE WI 54868<NL2><G> GROSS<NL>

A ticket printed using this format might look like the following:

RICE LAKE WEIGHING SYSTEMS 230 W COLEMAN ST RICE LAKE WI 54868

1345 LB GROSS

The ticket above could also be formatted by specifying the company address information in the Header Format ticket format, then substituting the <H1> token for the address in the Gross Format ticket format:

HDRFMT1=RICE LAKE WEIGHING SYSTEMS<NL>230 W COLEMAN ST<NL>RICE LAKE WI 54868<NL2>GFMT=<AE><G> GROSS<NL>

Enter. For example,

The HDRFMT1 command does not require the .FMT.

7.3.2 Using the Front Panel

If there is no access to equipment for communication through the communication ports or when working at a site where such equipment cannot be used, the Print Format formats. Using the Print Format

menu, edit the print format strings by changing the decimal values of the ASCII characters in

the format string.

Edit the format using the Alphanumeric Entry Procedure, see Section 1.9.

Some special characters cannot be displayed on the 882IS front panel (see the ASCII character chart on page 77) and are shown as blanks. The 882IS can send or receive any ASCII character; the character printed depends on the particular ASCII character set implemented for the receiving device.

7.3.3 Using Revolution

The Revolution configuration utility provides a print formatting grid with a tool bar. The grid allows the construction of the print format without the formatting tokens (<NL> and <SP>) required by the front panel or EDP command methods. Using Revolution, type text directly into the grid, then select weight value fields from the tool bar and place them where they are to appear on the printed ticket.

menu (see Section 3.2.14 on page 36) can be used to customize the print

64 Visit our website www.RiceLake.com

Page 71

Figure 7-1 shows an example of the Revolution print formatting grid.

Figure 7-1. Revolution Print Format Grid

Print Formatting

Page 72

882IS/882IS Plus

WARNING

Note

8.0 IO Module

The 882IS IO Module is an external device designed for use with the 882IS and 882IS Plus digital weight indicators. When placed in the safe area, its fiber optic interface allows it to provide remote functions for indicators in hazardous environments. The 882IS IO Module provides access to the indicator through the following:

• USB device connection

• EtherNet

• One comm port (RS-232 or RS-422)

• One option card slot

8.1 IO Module Disassembly

The 882IS IO module enclosure must be opened to connect cables for communications.

The IO module does not have an On/Off switch. Before opening the unit, ensure power to the unit is disconnected.

8.1.1 AC Wiring

The IO Module is to be permanently mounted (safe area) with a readily accessible disconnect device incorporated in the building installation wiring. All wiring is to be done in accordance with the National Electric Code (NEC).

8.1.2 RS-232/RS-422 Communications

To attach a PC or other device to the 882IS’ RS-232 or the two-wire RS-422 ports, select RS-422 standard in the indicator Serial menu for the IO Module. See Table 8-1 for information on connecting RS-422 communications.

Pin RS-232 RS-422

1 GND GND 2 RX B 3 TX A

Table 8-1. J3 Pin Assignments (Port 1 Serial Communications)

8.2 USB Device Communications – Port 2

The fiber optic port can be used to connect to the IO module. It can also:

• Connect to a PC or other indicator using fiber optics to RS-232 adapter

• Connect directly to another 882IS when one of the units is being used as a serial scale

If using Windows 7 or later, and the PC is connected to the Internet, the operating system may be able to install the drivers without any interaction.

Before the USB Device Port can be used, drivers must be installed on the PC.

1. Have power applied to the PC and to the indicator.

2. Connect a USB cable from the PC to the micro USB connector (J4) on the 882IS IO Module. The PC recognizes that a device has been connected and will attempt to install the drivers needed to make it work. Those drivers can be downloaded from the Rice Lake Weighing Systems’ website at

3. When the individual drivers are installed, a new COM Port designation is assigned for each physical USB port the 882IS is connected to on the PC.

For example, if the PC already has two physical RS-232 COM Ports, they most likely are designated COM1 and COM2. When connecting the indicator to a USB port on the PC, it will be assigned the next available port designation, or in this case, COM3. When plugging into the same physical USB port on the PC, the port designation will again be COM3. If plugging into another physical USB port on the PC, it will be assigned the next available designation, in this case COM4.

After the drivers are installed, use Windows Device Manager to determine the COM Port designation that was assigned to the USB port. Or open the application that is to be used with the 882IS, such as Revolution, and see which ports are available.

www.RiceLake.com

66 Visit our website www.RiceLake.com

Page 73

IO Module

Note

Configuration of the USB Device Port is done in the USB Communications sub-menu under IO MODULE PORTS in configuration mode (Section 3.2.13 on page 35).

The port can be configured as either a demand port for EDP commands and printing, or a data streaming port. Other settings include the termination character(s); enabling echoes and responses; adjust the end-of-line delay; and whether or not the indicator displays a 'print' message when a print format sends data out the port.

If a computer application has an open communications connection through the USB Device Port, and the physical cable connection is interrupted, a soft reset is performed on the indicator or power is cycled to the indicator; the connection in the computer application must be disconnected and reconnected again before it will continue to communicate with the indicator.

For the USB Device Port, it does not matter what the settings are for Baud, Data Bits, Parity and Stop Bits in the computer software. The port will communicate in the same way regardless of these settings.

This port is not a host port and is not intended to be connected to other devices such as keyboards, memory sticks or printers.

8.3 Ethernet Communications

The 882IS features Ethernet TCP/IP 10Base-T/100Base-TX communication using a standard RJ45 connector (J6 – see

Figure 8-1). It can support two simultaneous connections, one as a server, the other as a client.

Through an Ethernet network, software applications are able to communicate with the 882IS using the EDP command set (see

Section 6.0 on page 53), or data can be streamed continuously from the indicator, or printed on demand.

The Ethernet port supports both DHCP and manual configuration of settings such as the IP and subnet. In addition, the TCP Port number, Primary and Secondary DNS, and the Default Gateway can be configured using the Ethernet sub-menu of the Ports setup menu. For more information on configuring the Ethernet port see Section 3.2.12 on page 34.

Physical connection to the 882IS Ethernet port can be made directly from a PC to the 882IS (AdHoc Network), or through a network router or switch. The port supports auto-sensing MDI/MDIX cable configuration, so either straight-through or crossover cables can be used.

The RJ45 Ethernet jack on the 882IS houses two LEDs to indicate the status and speed of the connection.

Yellow LED (left) indicates the status of the connection:

• Off for no link

• On for a link

• Blinking if there is activity

Green LED (right) is:

• Off for a 10Base-T connection

• On for a 100Base-TX connection

Yellow LED

Green LED

Figure 8-1. RJ45 Ethernet Jack

Page 74

882IS/882IS Plus

9.0 Appendix

9.1 Error Messages

The 882IS indicator provides a number of error messages. When an error occurs, the message is shown on the indicator display. Error conditions can also be checked remotely by using the XE EDP command as described in Section 9.3.

9.1.1 Displayed Error Messages

The 882IS provides a number of front panel error messages to assist in problem diagnosis. Table 9-1 lists these messages and their meanings.

Error Message Description Solution

¯ ¯ ¯ ¯ ¯ ¯

(center dashes)

CFGERR Configuration error on power up if there was

ERROR Internal program error Check configuration. HWFERR Hardware failure error

NOTARE Tare is prevented because of regulatory mode

RANGE A numeric value entered in configuration is out

NO ZERO Zero is prevented (due to regulatory mode set-

Over range Under range

A/D out of range Or if using local/remote (serial scale) - loss of serial scale data.

an error loading configuration

on failure to write to the EEPROM any error (except for a battery error or an accumulation over range error) when exiting the menu

settings, the configuration of the TAREFN parameter, motion on the scale, etc.

of the acceptable range. The error is displayed momentarily – then parameter being edited is displayed so the value can be corrected.

tings, motion on the scale, zero range settings)

Table 9-1. 882IS Error Messages

Check for improper load cell wiring, configuration, calibration, scale hardware problems.

Press the

Change regulatory mode settings or the TAREFN parameter.

Re-enter a value that is in range for the parameter being edited.

Check zero settings and for motion.

Enter key to reboot the indicator.

68 Visit our website www.RiceLake.com

Page 75

Appendix

9.2 Using the HARDWARE Command

The HARDWARE serial command can be used to verify that installed option cards are recognized by the system. The HARDWARE command returns a three-digit card code, representing the card installed:

Code Card Type

000 No card installed 153 Analog Output Card 170 Fieldbus Option Card

Table 9-2. HARDWARE Command Option Card Type Codes

If an installed card is not recognized (HARDWARE command returns code of 000), ensure that the card is seated properly. Reinstall the card, if necessary, then cycle the power to read the configuration again. If the card is still not recognized, try a different option card.

9.3 ERROR Commands Output

The XE and XEH commands return a representation of any existing error conditions as described in the following table. If more than one error condition exists, the number returned is the sum of the values representing the error conditions. The XE command returns the value as a decimal representation and the XEH command returns the value as a hexadecimal representation.

XE Error Code

(decimal) Description

0 No Errors 0x00000000 1 Configuration Signature Error 0x00000001 2 Parameter Checksum Error 0x00000002 4 Loadcell Data Checksum Error 0x00000004 8 Print Format Checksum Error 0x00000008 64 Battery Power Low Voltage Error 0x00000040 32768 Gravity Compensation Error 0x00008000 65536 A/D Physical Error 0x00010000 131072 Tare Storage Checksum Error 0x00020000 262144 Accumulator Overflow Error 0x00040000

Table 9-3. Error Commands Output

XEH Error Code

(hexadecimal)

9.4 Status Messages

The EDP command P can be used to provide status about the indicator.

P EDP command returns whatever is currently shown in the indicator’s primary display area.

• The

PPPPPPP uu

where:

• PPPPPPP is the information shown on the primary display

• uu is the 2-digit units annunciator

If the indicator is in an underrange or overload condition, the weight value is replaced with &&&&&& (overload) or :::::: (underrange).

Page 76

882IS/882IS Plus

9.5 TARE and ZERO Key Functions

The function of the front panel Tare and Zero keys depend on the value specified for the Regulation parameter in the Features menu, see Figure 3-9 on page 30.

Table 9-4 describes the function of these keys for each of the regulatory modes.

Front Panel TARE Key or KTARE command

Regulation

Parameter Value Weight on Scale

NTEP zero or negative No Keyed prompt (1) No Action Keyed prompt (1) Zero

positive No Keyed prompt (1) Tare Tare Zero

CANADA zero or negative No Keyed prompt (1) No Action Keyed prompt (1) Zero

positive No No Action Tare Tare Zero

OIML zero or negative No Keyed prompt (1) No Action Keyed prompt (1) Zero

positive No Keyed prompt (1) Tare Tare Zero

NONE zero or negative No Keyed prompt (1) Tare Keyed prompt (1) Zero

positive No Keyed prompt (1) Tare Tare Zero

NOTES:

1. Entering a Zero tare will cancel the entry. Any other value will be accepted as a Keyed Tare.

2. Entering a Zero tare will clear the current Tare. Any other value will be accepted as a Keyed Tare.

3. The indicator will Zero and Clear the Tare only if the gross weight is within Zero Range. No action is taken if the weight is outside of Zero Range.

Tare in

System

Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero

Yes Keyed prompt (2) Tare Tare Zero

Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero

Yes No Action No Action No Action Zero

Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero and clear Tare (3)

Yes Keyed prompt (2) Tare Tare Zero and clear Tare (3)

Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero

Yes Keyed prompt (2) Clear tare Clear tare Zero

Table 9-4. Tare and Zero Key Functions for REGULA Parameter Settings

Table 9-5 lists the sub-parameters available when configuring a scale using INDUST mode. The table includes the default

values of the INDUST sub-parameters and the effective (not configurable) values used by NTEP, CANADA, OIML and NONE regulatory modes

(Tare Enable – tare function setting)

Front panel ZERO key or

KZERO commandKEYED PBONLY BOTH

REGULA/INDUST Parameter REGULA Mode

Parameter Description INDUST NTEP CANADA OIML NONE

SNPSHT Display or Scale weight source DISPLAY DISPLAY DISPLAY DISPLAY SCALE ZTARE Remove tare on ZERO NO NO NO YES YES KTARE Always allow keyed tare YES YES NO YES YES MTARE Multiple Tare Action REPLAC REPLAC NOTHIN REPLAC REMOVE NTARE Allow negative tare NO NO NO NO YES CTARE Allow CLEAR tare to clear tare YES YES YES NO YES

RTARE

PRTMOT Allow print while in motion NO NO NO NO YES PRTPT Add PT to keyed tare print NO NO YES YES NO OVRBAS Zero base for overload calculation CALIB CALIB CALIB SCALE CALIB

Round push button tare to nearest Display Division.

YES YES YES NO YES

Table 9-5. REGULA/INDUST Mode Parameters, Comparison with Effective Values of Regulatory Modes

70 Visit our website www.RiceLake.com

Page 77

Appendix

45910-XXXXXXX6/*5(/45&3.

"4$**

EFDJNBM

1PMBSJUZ TQBDF1PTJUJWF o/FHBUJWF

8FJHIUEJHJUTSJHIUKVTUJmFEEVNNZ [FSPFTEFDJNBMQPJOU XJUIOPMFBEJOH [FSPFTFYDFQUGPSMFBEJOH[FSPJNNFEJBUFMZ QSFDFEJOHUIF EFDJNBMQPJOU-FBEJOH [FSPFTUSBOTNJUUFEBTTQBDFT

-QPVOET ,LJMPHSBNT 5UPOT55/

-5

 0PVODFT (HSBNT TQBDF(/

530:0;530:-# PS/0/&

((SPTT

//FU

4UBUVT TQBDFWBMJE **OWBMJE ..PUJPO 00WFSVOEFSSBOHF

$3-'

PS$3

Note

9.6 Data Formats

9.6.1 Stream Serial Data Format

If stream data transmission is configured for a port (STRLFT or STRIND), by default the 882IS sends data using the Rice Lake Weighing Systems serial data format shown in Figure 9-1.

Figure 9-1. Stream Serial Data Format

Stream Format parameter default – <2><P><W7.><U><M><S><CR><LF>

Format can be changed, see Section 9.7. The character values can be changed for the stream format tokens, see Table 6-7 on page 57.

9.6.2 Print Output Serial Data Format

The 882IS uses a data string format for a basic ticket printout. The print format is configured in the setup menu for the demand (print) port, and depends on the indicator configuration and mode. See Section 7.0 on page 62 for print formatting.

Use the EDP commands, Revolution

or the front panel to fully customize the print to work with a wide variety of printers and

other remote equipment.

9.7 Custom Stream Formatting – Input/Output

The format of the streamed data can be configured for any of the ports individually using the front panel, EDP commands or Revolution using the tokens in Table 9-6. Configuration is available for stream input/output tokens through EDP commands only; no front panel access is provided.

Format Identifier Defined By Description

<P[G | N | T]> STR.POS

STR.NEG

<U[P | S | T]> STR.PRI

STR.SEC STR.TER

<M[G | N | T]> STR.GROSS

STR.NET STR.TARE

<S> STR.MOTION

STR.RANGE STR.OK STR.INVALID STR.ZERO

Polarity. Outputs the positive or negative polarity label for the current or specified (Gross/Net/Tare) weight on the source scale. Possible values are SPACE, NONE, + (for STR.POS), or – (for STR.NEG)

Units. Outputs the primary, secondary, or tertiary* units label for the current or specified (Primary/Secondary/ Tertiary*) weight on the source scale.

Mode. Outputs the gross, net, or tare label for the current or specified weight (Gross/Net/Tare) on the source scale.

Outputs the status for the source scale. Default values and meanings for each status: STR.MOTIONM In motion STR.RANGEO Out of range STR.OK <space> OK STR.INVALIDI Invalid STR.ZERO Z COZ

Table 9-6. Custom Stream Format Identifiers

Page 78

882IS/882IS Plus

Format Identifier Defined By Description

<B [–]n,…> See descriptions

below B0 - Always 0 B1 - Always 1 B2 Configuration =1 if even parity B3 Dynamic =1 if MODE=NET B4 Dynamic =1 if COZ (center of zero) B5 Dynamic =1 if motion B6 Dynamic =1 if displayed gross or net weight is negative B7 Dynamic =1 if out of range B8 Dynamic =1 if secondary/tertiary* B9 Dynamic =1 if tare in system B10 Dynamic =1 if tare is keyed B11 Dynamic =00 if MODE=GROSS

B12 Dynamic =00 if UNITS=PRIMARY

B13 Configuration =00 (not used)

B14 Configuration =00 (not used)

B15 Configuration =00 (not used)

B16 Configuration =00 (not used)

B17 Configuration =000 (not used)

B18 Configuration =000 (not used)

Bit fields. Comma-separated sequence of bit field specifiers. Must be exactly 8 bits. Minus sign ([–]) inverts the bit.

=01 if MODE=NET =10 if UNITS=TERTIARY* =11 (not used)

=01 if UNITS=PRIMARY =10 if UNITS=PRIMARY =11 (note used)

=01 if current DSPDIV=1 =10 if current DSPDIV=2 =11 if current DSPDIV=5

=01 if primary DSPDIV=1 =10 if primary DSPDIV=2 =11 if primary DSPDIV=5

=01 if secondary DSPDIV=1 =10 if secondary DSPDIV=2 =11 if secondary DSPDIV=5

=01 if tertiary* DSPDIV=1 =10 if tertiary* DSPDIV=2 =11 if tertiary* DSPDIV=5

=001 if current DECPNT=888880 =010 if current DECPNT=888888 =011 if current DECPNT=88888.8 =100 if current DECPNT=8888.88 =101 if current DECPNT=888.888 =110 if current DECPNT=88.8888 =111 if current DECPNT=8.88888

=001 if primary DECPNT=888880 =010 if primary DECPNT=888888 =011 if primary DECPNT=88888.8 =100 if primary DECPNT=8888.88 =101 if primary DECPNT=888.888 =110 if primary DECPNT=88.8888 =111 if primary DECPNT=8.88888

Table 9-6. Custom Stream Format Identifiers (Continued)

72 Visit our website www.RiceLake.com

Page 79

Appendix

Format Identifier Defined By Description

B19 Configuration =000 (not used)

=001 if secondary DECPNT=888880 =010 if secondary DECPNT=888888 =011 if secondary DECPNT=88888.8 =100 if secondary DECPNT=8888.88 =101 if secondary DECPNT=888.888 =110 if secondary DECPNT=88.8888 =111 if secondary DECPNT=8.88888

B20 Configuration =000 (not used)

=001 if tertiary* DECPNT=888880 =010 if tertiary* DECPNT=888888 =011 if tertiary* DECPNT=88888.8 =100 if tertiary* DECPNT=8888.88 =101 if tertiary* DECPNT=888.888 =110 if tertiary* DECPNT=88.8888 =111 if tertiary* DECPNT=8.88888

<CR> - Carriage return, hex 0x0D, ASCII decimal 13 <LF> - Line feed, hex 0x0A, ASCII decimal 10 <SPnn> - Space, nn = number of spaces.

<NLnn> TERMIN setting of

<nnn> - ASCII character (nnn = decimal value of ASCII character). Used for inserting control characters (<002> for an

* Tertiary (Range/Interval 3)

Scale weight Weight for the source scale. wspec is defined as follows:

wspec Indicates whether the weight is the current displayed weight (W, w), gross (G, g), net (N, n), or tare (T, t) weight. Upper-case letters specify right-justified weights; lower-case are left-justified. Optional /P, /S, or /T suffixes can be added before the ending delimiter (>) to specify weight display in primary (/P), secondary (/S), or tertiary* (/T) units. [–] Enter a minus sign (–) to include sign for negative values. [0] Enter a zero (0) to display leading zeroes. digit[[.][.]digit] The first digit indicates the field width in characters – range is 1-7. Decimal point only indicates floating decimal; decimal point with following digit (range is 1-5) indicates fixed decimal with n digits to the right of the decimal. Two consecutive decimals send the decimal point even if it falls at the end of the transmitted weight field.

If nn is not specified, 1 is assumed. Value must be in the range 1-99. New line, nn = number of termination (<CR/LF> or <CR>) characters.

the port

If nn is not specified, 1 is assumed. Value must be in the range 1-99. Note: when streaming data, a configured End-of-Line Delay is performed after each New Line.

STX, for example) in the output.

Table 9-6. Custom Stream Format Identifiers (Continued)

Page 80

882IS/882IS Plus

9.8 Stream Formatting Examples

9.8.1 Toledo 8142 Indicator

Sample string for Toledo 8142 indicator (with no checksum):

882IS stream format configuration:<02><B2, B0, B1, B13, B17><B2, B0, B1, B8, B5, B7, B6, B3><B2, B0, B1, B0, B0, B0, B0, B0><W6><T6><CR>

Identifier Description

<STX> The STX character is entered into the string using the <02> hex value. <Status Word A> Toledo status words are made up of various bit fields.

NOTE: Identifiers must be entered beginning with the high-order bit (bit 7–bit 0) of the Toledo status word.

Status Word A contains the following fields. Equivalent 882IS format identifiers are shown in parentheses Bit 7: parity (B2) Bit 6: always 0 (B0) Bit 5: always 1 (B1) Bits 3–4: display divisions (B13) Bits 0–2: decimal format (B17)

<Status Word B> Status Word B contains the following fields. Equivalent 882IS format identifiers are shown in parentheses

Bit 7: parity (B2) Bit 6: always 0 (B0) Bit 5: always 1 (B1) Bit 4: lb/kg units (B8) Bit 3: stable/motion (B5) Bit 2: in/out-of-range (B7) Bit 1: pos/neg (B6) Bit 0: gross/net (B3)

<Status Word C> Status Word C contains the following fields. Equivalent 882IS format identifiers are shown in parentheses

Bit 7: parity (B2) Bit 6: always 0 (B0) Bit 5: always 1 (B1) Bits 0–4: always 0 (B0)

<wwwwww> The <W6> and <T6> indicate six digits of indicated weight and tare weight. Valid characters are W, w, G, g, T, t, N, or n (lower

case indicates left justified). W indicates current weight, G gross weight, N net weight, and T tare weight. /P and /S can be used to specify primary or secondary.

Minus indicates sign inclusion, and (0) indicates leading zeros. First digit indicates field width in characters. Decimal indicates floating decimal point. Decimal with subsequent digit indicates fixed decimal with n digits to the right of the decimal. Two consecutive decimals (for example, <W06..>)

send the decimal point even if it falls at the end of the transmitted weight field. <tttttt> Tare weight. See description above <EOL> <CR> is entered at the end of the string as the end of line character in this example

Table 9-7. Toledo Sample String Identifiers

74 Visit our website www.RiceLake.com

Page 81

Appendix

9.8.2 Cardinal 738 Indicator

Sample string for the Cardinal 738 indicator:

882IS stream format configuration:

Identifier Description

<CR> Carriage Return <POL> Cardinal uses + for positive and – for negative, so the stream polarity tokens need to reflect this. The EDP commands for the

882IS are STR.POS=+ and STR.NEG= –.

<wwwwwww> The <W07.> identifier that the 882IS recognizes indicates seven digits of weight with a decimal and leading zeros, with the deci-

mal being sent at the end of the weight. Valid characters are W, w, G, g, T, t, N, or n (lower case indicates left justified). W indicates current weight, G gross weight, N net weight, T tare weight. /P and /S can be used to specify primary or secondary.

Minus indicates sign inclusion, while (0) indicates leading zeros. First digit indicates field width in characters. Decimal indicates floating decimal point. Decimal with subsequent digit indicates fixed decimal with n digits to the right of the decimal. Two consecutive decimals (for example, <W06.>) send the decimal point even if it falls at the end of the transmitted weight field.

<S> There are four possible tokens for status bits that can be used: motion, out-of-range, valid, and invalid. In the Cardinal, m indi-

cates motion, o indicates out-of-range, and a space is used for valid or invalid weights. The commands to set these tokens in the 882IS are STR.MOTION=m, STR.RANGE=o, STR.OK= , STR.INVALID= .

NOTE: Although it appears that there are no commands for OK and INVALID, there is a space entered with the keyboard before pressing the Enter key.

<SP> Space <units> The Cardinal uses two-character, lower-case units identifiers. The commands to set these tokens in the 882IS include:

STR.PRI=lb (options: kg, g, tn, t , gr, oz, or sp), STR.SEC=kg (options: lb, g, tn, t , gr, oz, or sp). <SP> Space <G/N> The mode used for Cardinal is g for gross and n for net. These tokens are set using the STR.GROSS=g and STR.NET=n tokens. <SP> Space <SP> Space <EOL> The end of line character is an ETX in this case so the hex value of <03> is entered in the string.

Table 9-8. Cardinal Sample String Identifiers

Page 82

882IS/882IS Plus

9.8.3 Weightronix WI 120 Indicator

Sample string for the Weightronix WI120 indicator:

882IS stream format configuration:

Identifier Description

<SP> Space <G/N> The mode used for Weightronix is G for gross and N for net. These tokens are set using the STR.GROSS=G and STR.NET=N

tokens. <POL> Since the Weightronix uses + for positive and – for negative, the polarity tokens need to reflect this. The EDP commands for the

882IS are STR.POS=+ and STR.NEG= –. <wwwwww> The <W06.> that the 882IS recognizes indicates six digits of weight with a decimal and leading zeroes. Valid characters are W, w,

G, g, T, t, N, or n (lower case indicates left justified). W indicates current weight, G gross weight, N net weight, and T tare weight.

/P and /S can be used to specify primary or secondary.

Minus indicates sign inclusion, while (0) indicates leading zeros. First digit indicates field width in characters. Decimal indicates

floating decimal point. Decimal with subsequent digit indicates fixed decimal with n digits to the right of the decimal. Two consec-

utive decimals (for example, <W06..>)

send the decimal point even if it falls at the end of the transmitted weight field. <SP> Space <units> The Weightronix uses two-character, lower-case units identifiers. The commands to set these tokens in the 882IS include:

STR.PRI=lb (options: kg, g, tn, t , gr, oz, or sp), STR.SEC=kg (options: lb, g, tn, t , gr, oz, or sp). <EOL> <CR> or <CR> and <LF>

Table 9-9. Weightronix Sample String Identifiers

76 Visit our website www.RiceLake.com

Page 83

Appendix

9.9 ASCII Character Chart

Use the decimal values for ASCII characters listed in Tables 9-10 and 9-11 when specifying print format strings in the 882IS Print Format menu or serial stream formats. The actual character printed depends on the character mapping used by the output device.

The 882IS can send or receive any ASCII character value (decimal 0–255). Due to limitations of the indicator display, some characters cannot be shown.

Control ASCII Dec Hex ASCII Dec Hex ASCII Dec Hex ASCII Dec Hex

Ctrl-@ NUL 00 00 space 32 20 @ 64 40 ` 96 60 Ctrl-A SOH 01 01 ! 33 21 A 65 41 a 97 61 Ctrl-B STX 02 02 “ 34 22 B 66 42 b 98 62 Ctrl-C ETX 03 03 # 35 23 C 67 43 c 99 63 Ctrl-D EOT 04 04 $ 36 24 D 68 44 d 100 64 Ctrl-E ENQ 05 05 % 37 25 E 69 45 e 101 65 Ctrl-F ACK 06 06 & 38 26 F 70 46 f 102 66 Ctrl-G BEL 07 07 ’ 39 27 G 71 47 g 103 67 Ctrl-H BS 08 08 ( 40 28 H 72 48 h 104 68 Ctrl-I HT 09 09 ) 41 29 I 73 49 i 105 69 Ctrl-J LF 10 0A * 42 2A J 74 4A j 106 6A Ctrl-K VT 11 0B + 43 2B K 75 4B k 107 6B Ctrl-L FF 12 0C , 44 2C L 76 4C l 108 6C Ctrl-M CR 13 0D - 45 2D M 77 4D m 109 6D Ctrl-N SO 14 0E . 46 2E N 78 4E n 110 6E Ctrl-O SI 15 0F / 47 2F O 79 4F o 111 6F Ctrl-P DLE 16 10 0 48 30 P 80 50 p 112 70 Ctrl-Q DC1 17 11 1 49 31 Q 81 51 q 113 71 Ctrl-R DC2 18 12 2 50 32 R 82 52 r 114 72 Ctrl-S DC3 19 13 3 51 33 S 83 53 s 115 73 Ctrl-T DC4 20 14 4 52 34 T 84 54 t 116 74 Ctrl-U NAK 21 15 5 53 35 U 85 55 u 117 75 Ctrl-V SYN 22 16 6 54 36 V 86 56 v 118 76 Ctrl-W ETB 23 17 7 55 37 W 87 57 w 119 77 Ctrl-X CAN 24 18 8 56 38 X 88 58 x 120 78 Ctrl-Y EM 25 19 9 57 39 Y 89 59 y 121 79 Ctrl-Z SUB 26 1A : 58 3A Z 90 5A z 122 7A Ctrl-[ ESC 27 1B ; 59 3B [ 91 5B { 123 7B Ctrl-\ FS 28 1C < 60 3C \ 92 5C | 124 7C Ctrl-] GS 29 1D = 61 3D ] 93 5D } 125 7D Ctrl-^ RS 30 1E > 62 3E ^ 94 Ctrl-_ US 31 1F ? 63 3F _ 95 5F DEL 127 7F

Table 9-10. ASCII Character Chart (Part 1)

5E ~ 1

26 7E

Page 84

882IS/882IS Plus

ASCII Dec Hex ASCII Dec Hex ASCII Dec Hex ASCII Dec Hex

Ç 128 80 á 160 A0 192 C0 a 224 E0 ü 129 81 í 161 A1 193 C1 b 225 E1 é 130 82 ó 162 A2 194 C2 G 226 E2 â 131 83 ú 163 A3 195 C3 p 227 E3 ä 132 84 ñ 164 A4 196 C4 S 228 E4 à 133 85 Ñ 165 A5 197 C5 s 229 E5 å 134 86 ª 166 A6 198 C6 m 230 E6 ç 135 87 º 167 A7 199 C7 t 231 E7 ê 136 88 ¿ 168 A8 200 C8 F 232 E8 ë 137 89 169 A9 201 C9 Q 233 E9 è 138 8A ¬ 170 AA 202 CA W 234 EA ï 139 8B 1/2 171 AB 203 CB d 235 EB î 140 8C 1/4 172 AC 204 CC ¥ 236 EC ì 141 8D ¡ 173 AD 205 CD f 237 ED Ä 142 8E « 174 AE 206 CE Î 238 EE Å 143 8F » 175 AF 207 CF Ç 239 EF É 144 90 176 B0 208 D0 º 240 F0 æ 145 91 177 B1 209 D1 ± 241 F1 Æ 146 92 178 B2 210 D2 ³ 242 F2 ô 147 93 179 B3 211 D3 £ 243 F3 ö 148 94 180 B4 212 D4 ó 244 F4 ò 149 95 181 B5 213 D5 õ 245 F5 û 150 96 182 B6 214 D6 ¸ 246 F6 ù 151 97 183 B7 215 D7 » 247 F7 ÿ 152 98 184 B8 216 D8 ° 248 F8 Ö 153 99 185 B9 217 D9 · 249 F9 Ü 154 9A 186 BA 218 DA 250 FA ¢ 155 9B 187 BB 219 DB 251 FB £ 156 9C 188 BC 220 DC 252 FC ¥ 157 9D 189 BD 221 DD Pts 158 9E 190 BE 222 DE 254 FE ƒ 159 9F 191 BF 223 DF 255 FF

253 FD

Table 9-11. ASCII Character Chart (Part 2)

78 Visit our website www.RiceLake.com

Page 85

Appendix

9.10 Digital Filtering

Digital filtering can be used to create a stable scale reading in challenging environments. The 882IS has two filtering methods that can be set; Sample rate and Digital filter.

9.10.1 Sample Rate:

The Sample rate should be set first. Better stability is achieved with a lower sample rate setting, so 7.5 Hz is more stable than 120 Hz.

9.10.2 Digital Filter:

The digital filter is an adaptive filter that has two parameters to set the filter settling and response times: sensitivity and threshold.

Digital Filtering Sensitivity

Digital filtering sensitivity controls the stability and settling time of the scale. The sensitivity parameter can be set to heavy, medium, or light. A heavy setting will result in an output that is more stable and will settle more slowly than that of light. However, small changes in weight data (a few grads) on the scale base will not be seen as quickly.

If the difference in typical subsequent weight values on the scale will be only a few grads, use a light setting. If using a truck scale where the changes in subsequent weight values will be 100s of grads, a heavy setting will be more appropriate.

Digital Filtering Threshold

With the digital filter threshold set at zero, determine the amount of instability that is present. Convert this instability to display divisions. The number of display divisions of instability will be used to set the threshold of the digital filter. The digital filter can be set to Off by entering 0 in the Filter Threshold

Digital filtering threshold should be set for the amount of observed noise in the system. This parameter can be set in the range of 0 to 99999 display divisions. When a new sampled weight value is acquired, the adaptive filter compares the new value to the previous (filtered) output value. If the difference between the new value and the previous output value is greater than the Filter Threshold parameter (displayed division) the adaptive filter output is reset. The newly acquired sample value replaces the filtered output. If the difference between the new value and the previous output value is less than the Filter Threshold parameter, the two values are averaged together using a weighted average. The weighed average is based on the amount of the difference, time the system has been stable, and selected Filter Sensitivity value.

parameter.

Page 86

882IS/882IS Plus

Note

TAR E

9.11 Analog Output Calibration

See Section 3.0 on page 23, Table 3-15 for Analog Output parameters. The following calibration procedure requires a multimeter to measure voltage or current output from the analog output module.

If the option is not already installed, install it in according to the instructions included with the option.

The analog output must be calibrated after the indicator itself has been configured (Section 4.0) and calibrated

(Section 4.0).

1. Enter configuration mode and go to the Analog Output menu.

• Set OUTPUT as desired for 0-10V, 0-20mA, or 4-20mA output

the minimum calibration occurs at 0.5V and 1mA for a 0-10V and 0-20mA output respectively.

• Set the minimum value to lowest weight value to be tracked by the analog output

• Set the maximum value to highest weight value to be tracked by the analog output

2. Connect multimeter to connector J1 on the analog output board:

• For voltage output, connect voltmeter leads to pins 3 and 4 (-V, +V)

• For current output, connect ammeter leads to pins 1 and 2 (-mA, +mA)

3. Adjust zero calibration:

• Scroll to the Calibrate Zero parameter

• Press , 000000 displays

• Check voltage or current reading on multimeter

• Set the parameter to match the reading from the multimeter

• Press or to select the digit

• Press or to increment or decrement the value

• Press to move to the decimal point entry

• Press or to adjust the decimal point placement

• Press to accept the displayed value

• CAL is displayed while the calibration is being performed.

4. Adjust span calibration:

• Scroll to the Calibrate Span parameter

• Press , 000000 displays

• Set the parameter to match the reading from the multimeter

• Press or to select the digit

• Press or to increment or decrement the value

• Press to move to the decimal point entry

• Press or to adjust the decimal point placement

• Press to accept the displayed value

• CAL will be displayed while the calibration is being performed

5. Verify calibration:

• Return to the Calibrate Zero/Calibrate Span parameter and verify that the calibration has not drifted.

• Repeat calibration if needed

6. Return to weigh mode. Analog output function can be verified using test weights.

80 Visit our website www.RiceLake.com

Page 87

10.0 Compliance

5LFH/DNH:HLJKLQJ6\VWHPV

:HVW&ROHPDQ6WUHHW

5LFH/DNH:LVFRQVLQ

8QLWHG6WDWHVRI$PHULFD

6LJQDWXUH __________________________

3ODFH

7\SH1DPH 'DWH

7LWOH

5LFKDUG6KLSPDQ

4XDOLW\0DQDJHU

(8DECLARATIONOF

CONFORMITY

("#+,.$-#0#(1

#1/ 1 (11  #&1

(8'LUHFWLYH &HUWLILFDWHV

6WDQGDUGV8VHG1RWLILHG%RG\,QYROYHPHQW

__________________________

5LFH/DNH:,86$

__________________________

7\SH7\S7\SH

(QJOLVK :H GHFODUHXQGHU RXU VROHUHVSRQVLELOLW\ WKDW WKHSURGXFWVWR ZKLFK WKLVGHFODUDWLRQ UHIHUVWRLV LQ FRQIRUPLW\ZLWK WKH IROORZLQJ

VWDQGDUGV RURWKHUUHJXODWLRQVGRFXPHQWV

'HXWVFK :LU HUNOlUHQXQWHUXQVHUHUDOOHLQLJHQ9HUDQWZRUWXQJ GDVV GLH 3URGXNWH DXI GLHVLFK GLHVH (UNOlUXQJEH]LHKWGHQIROJHQGHQ 1RUPHQ

XQG 5HJXOLHUXQJVEHVWLPPXQJHQHQWVSUHFKHQ

)UDQFDLV 1RXVGpFODURQVVRXVQRWUHUHVSRQVDELOLWpTXHOHVSURGXLWVDX[TXHOVVHUDSSRUWHODSUpVHQWHGpFODUWLRQVRQWFRQIRUPHVjODDX[QRUPHV

VXLYDQWHRXDXDX[GRFXPHQWVQRUPDWLIVVXLYDQWV

_______________________

Compliance

882IS/882IS Plus indicator, mb-EPS-100-240-X2 power supply and IS6V2 battery module, IO module

2014/30/EU EMC

2014/35/EU LVD

2011/65/EU RoHS

2014/34/EU ATEX

FM18ATEX0047X

EN 61326-1:2013, EN 55011:2009+A1:2010

Applicable to: / Aufwendbar auf: / Applicable a: IO module EN 60950-1:2006+A11:2009/A1:2010/A12:2011/A2:2013

EN 50581:2012

Applicable to: / Aufwendbar auf: / Applicable a: Indicator,power supply and battery module EN 60079-0:2012+A11:2013, EN 60079-11:2012, EN 60079-18:2015, EN 60529:1991 +A1:2000/A2:2013 Notified Body involved with module B and D: / Benannte Stelle, die an Modul B und D beteiligt ist: / Organisme notifié impliqué dans les modules B et D: FM Approvals Europe Ltd. - 2809

May 3, 2019

Page 88

882IS/882IS Plus

11.0 Specifications

Power

Nominal Voltage Intrinsically safe power supply (7.5 VDC

output) or optional 6 VDC battery Minimum Voltage 5.8 VDC Maximum Voltage 7.9 VDC Current Consumption 100 mA average

175 mA maximum (4 x 350W load cells) Max Power Consumption 0.25 watts Temperature T4 Fusing 3 x 125 mA, fully-encapsulated

Analog Specifications

Full Scale Input Signal 0.6 mV/V - 4.0 mV/V Load Cell Excitation 3.0VDC (350W); 4.6VDC (700W)

Load Cell Current 34 mA (4 x 350W or 8 x 700W load cells) Analog Signal

Input Range -0.65 mV/V to 4.0 mV/V

Analog Signal

Sensitivity 0.2 µV/graduation minimum,

1.5 µV/grad. recommended Input Impedance 200 MW typical Internal Resolution 8,000,000 count

Display Resolution 10 000 dd maximum (NTEP certified) Measurement Rate Up to 60 measurements/sec. System Linearity Within 0.01% of full scale Zero Stability 150 nV/°C, maximum Span Stability 3.5 ppm/°C, maximum Calibration Method Software, constants stored in EEPROM RFI Protection Signal, excitation, and sense lines protected

by capacitor bypass

ESD/Transient

Protection 600 watt PPD, Transient

voltage suppressors

Environmental

Operating Temperature 14 to +104°F (-10 to +40°C) Storage Temperature -13 to +158°F (-25 to +70°C) Humidity 0–95% relative humidity

Enclosure

Enclosure Dimensions 9.6 in x 6.5 in x 4.3 in

24 cm x 17 cm x 11 cm Weight 2.8 Kg (6.1 lb) Rating/Material Stainless Steel IP-66

Certifications and Approvals

FM18US0195X FM18ATEX0047X IECx FMG 18.0018X FM18CA0092X

NTEP CoC Number 19-015 Accuracy ClassIII/III L

: 10 000

max

** File Number: E151461-A23-UL

IEC 6100-4-2

± 8 kv contact ± 15 kv air discharge

Optical Port

Physical Medium 2.2mm plastic fiber @ 640 nm Max Transmission Length 246 ft. (75 m)

Operator Interface

Display 7-digit LCD display. 7-segment, 121 x 24 dot

matrix with white LED background

LCD annunciators Gross, net, center of zero, standstill, lb/primary

units, kg/secondary units, count, tare

Front Panel 11 button flat membrane panel (including F1,

F2, F3, F4, On/Off, Menu, Tare, Zero, Gross/ Net, Units, Print)

882IS Plus - Numeric keypad

82 Visit our website www.RiceLake.com

(Pending)

The 882IS complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause undesired operation.

** UL is only applicable to 882IS IO and battery charger

Page 89

Page 90

230 W. Coleman St. • Rice Lake, WI 54868 • USA

U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319

Rice Lake Weighing Systems is an ISO 9001 registered company.

www.ricelake.com

August 20, 2019

PN 183532 Rev B

Rice Lake Weighing Systems 882IS Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1.0 Introduction

1.1 Overview

1.2 Options

1.3 Safety

1.4 FM Approval

1.5 Hazardous Location Labels

1.6 Operating Modes

1.7 Front Panel Display

1.8 General Navigation

1.9 Indicator Operations

1.9.1 Toggle Gross/Net Mode

1.9.2 Toggle Units

1.9.3 Zero Scale

1.9.4 Acquire Tare

1.9.5 Remove Tare Value

1.9.6 Preset Tare (Keyed Tare)

1.9.7 Print Ticket

1.9.8 Front Panel User Setup

1.9.9 Displaying Audit Trail Information

1.9.10 Display Accumulator

1.9.11 Clear the Accumulator

1.9.12 Display Tare

2.0 Installation

2.1 Unpacking and Assembly

2.2 Product Dimensions

2.3 Hazardous Area Installation of the 882IS

2.4 Mounting Instructions

2.4.1 Backplate Removal

2.5 Cable Connections on the 882IS

2.5.1 Power Supply to Indicator

2.5.2 AC Power Wiring

2.5.3 Battery Option

2.5.4 Load Cells

2.5.5 Cable Shield Grounding

2.5.6 882IS Enclosure Grounding

2.5.7 CPU Board Replacement

2.5.8 Serial Communications – Port 1 (COM)

2.6 CPU Board

2.7 Audit Trail

2.8 Digital Inputs

2.9 Backplate Attachment

2.10 Legal for Trade Sealing

2.11 IO Module Option Cards

2.12 Rechargeable Battery Usage

2.13 Replacement Parts

3.0 Configuration

3.1 Configuration Methods

3.2 User Setup Menu

3.2.1 Audit Menu

3.2.2 Setup Menu

3.2.3 Scale Menu

3.2.4 Scale Format Menu - if Split = Off

3.2.5 Scale Format Menu - if split = 2 RNG, 3 RNG, 2 INTVL, 3 INTVL

3.2.6 Calibration Menu

3.2.7 Features Menu

3.2.8 Region Menu

3.2.9 Region - Regulation - Indust

3.2.10 Keylock Menu

3.2.11 Setup Ports Menu

3.2.12 Ports - Serial Ports Menu

3.2.13 Ports - Fiber Optics Menu

3.2.14 Print Format Menu

3.2.15 Digital Inputs Menu

3.2.16 IO Module Menu

3.2.17 Power Savings Menu

3.2.18 Version Menu

3.3 Test Menu

3.4 Time and Date

3.5 Accumulator Menu

3.6 Tare

4.0 Calibration

4.1 Front Panel Calibration

4.1.1 Five-Point Linearization

4.1.2 Rezero

4.2 Last Zero

4.3 Temporary Zero