Rice Lake Versa-portion RLP-S, Versa-portion RLP-SM Operation Manual

®

Versa-portion RLP-S/SM

Multi-Purpose Bench Scale

Counting Scale

Operation Manual

115519

Contents

1.0 Introduction.................................................................................................................................. 1

1.1 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Operation...................................................................................................................................... 2

2.1 On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.2 Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.3 Automatic Shut-Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.4 Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.5 Default Primary Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.6 G, lb and oz Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3.0 Calibration ................................................................................................................................... 3

3.1 Software Version and Span State Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.2 Performing a Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.3 Enclosure Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.4 Setting the SPEC Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.5 Internal Count and A/D Count Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.0 Appendix ...................................................................................................................................... 6

4.1 DC Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.1.1 Battery Pack Replacement/Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.1.2 Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.2 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5.0 Specifications.............................................................................................................................. 7

Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.

© 2011 Rice Lake Weighing Systems. All rights reserved. Printed in the United States of America.

Rice Lake Weighing Systems is an ISO 9001 registered company.

Specifications subject to change without notice.

Version 2 12/2011

Rice Lake continually offers web-based video training on a growing selection

of product-related topics at no cost. Visit www.ricelake.com/webinars.

II

About This Manual

This manual contains operating procedures for the Versa-portion RLP-S/SM multi-purpose bench scale.

Caution

Procedures that require working inside
the scale base are to be performed by
qualified service personnel only.

This manual can be viewed or
downloaded from the RLWS website at

www.ricelake.com/manuals.

1.0 Introduction

The Versa-portion RLP-S/SM is a multi-purpose bench scale that offers practical solutions for a full range of
applications. Its internal resolution of 1/90,000 gives you maximum precision and accuracy. Its backlit LCD
display enables operators to easily see weights. When portability is required, choose the optional rechargeable
battery for over 60 hours of continuous usage. The Versa-portion RLP-S/SM is designed to reliably operate in
many environments and withstand transport from one area of the plant to another or from one business to the
next.

1.1 Front Panel

Table 1-1 lists the indications and front-panel buttons available on the Versa-portion RLP-S/SM.

Indication Description

On when the weight display is in ounces
*(not available in Versa-portion RLP-SM)

On when the weight display is in pounds
*(not available in Versa-portion RLP-SM)

On when the weight display is in grams

*

*

*

(kg)

*(Versa-portion RLP-SM value is kg, display is in kilograms)

On when the zero point is adjusted and the weight is stable

On when tare subtraction is performed

On (blinking) when the battery is weak and needs to be recharged

Front-Panel Button Description

Resets the weight display to zero

Sets or clears the tare value

Turns the display on/off

Changes measurement units between lb, oz, g, kg

(not available in Versa-portion RLP-SM)

Table 1-1. Versa-portion RLP-S/SM Indications and Front-Panel Buttons

Introduction 1

2.0 Operation

2.1 On/Off

1. Press the POWER key. The display will blink

8.8.8.8.8.8. and show 0.000 when ready to

weigh.

2.2 Tare

Tare values can be used for up to half of scale
capacity.

Performing a Tare

1. Place the item to be tared (typically a
container) on the platter.

2. Press the

3. The display will show

TARE key.

0.000 with the tared

item on the platter.

Removing a Stored Tare

1. Remove the tared item from the platter.

2. Press the

3. The display will show

TARE key.

0.000.

2.3 Automatic Shut-Off Timer

The Versa-portion RLP-S/SM has a built-in automatic
shut-off timer. This timer can be set to turn the unit off
after three minutes of inactivity or 10 minutes of
inactivity.

Setting the Timer for Three Minutes

1. If the unit is powered on, press the POWER
key until it shuts down.

2. With the unit powered off, press and hold the

POWER key for three seconds.

The display will show 3.

3. Release the
to turn the unit off after three minutes of
inactivity.

Setting the Timer for 10 Minutes

1. If the unit is powered on, press the POWER
key until it powers off.

2. With the unit powered off, press and hold the

POWER key for six seconds.

The display will show 3 after a period of three
seconds. It will show 10 after six seconds.

3. Once the display shows

POWER key. The timer is now set to turn the

unit off after 10 minutes of inactivity.

POWER key. The timer is now set

10, release the

Disabling the Timer

1. If the unit is powered on, press the POWER
key until it shuts down.

2. With the unit powered off, press and hold the

POWER key for nine seconds.

The display will show 3 after a period of three
seconds and 6 after six seconds. It will show

999 after nine seconds.

3. Once the display shows

POWER key. The timer is now disabled.

999, release the

2.4 Display Brightness

The Versa-portion RLP-S/SM display brightness can
be set to one of three levels.

Changing the brightness setting

1. Hold the ZERO key and press Tare three times.

2. Press the

ZERO key to increase the dimmer

level and the Power button to decrease the
dimmer level.

3. The display will show

1, 2, 3, or 4 depending

on which dimmer level is being displayed.

4. Press the

TARE key to save the setting and

return to weigh mode.

2.5 Default Primary Unit

The Units bu t ton c ycl e s thr o ug h g , lb, a n d oz.
(Versa-portion RLP-SM is only available in kg)

Setting the Default Primary Unit

1. Hold the ZERO key and press the UNITS key
three times.

2. Press the

POWER key to cycle through

available units.

3. When the desired default unit is displayed,

s the TARE key to save the setting and

pres
return to weigh mode.

2.6 G, lb and oz Conversion

(Not available in Versa-portion RLP-SM)

G, lb and oz conversion is available only when
SPEC08=011 (see Section 3.4).

1. Switch between units by pressing the
key.

(G) uppercase is the abbreviation for gross.

Note

(g) lowercase is the correct abbreviation for
grams.

UNITS

2 Versa-portion RLP-S/SM Operation Manual

3.0 Calibration

To enter calibration mode, remove the screw on the bottom of the scale as shown in Figure 3-1. Use a small tool
to press the span setup switch located under the screw. Setup will time out to verify the switch is set to the
position. Then, perform a span switch state check (see Section 3.1).

Remove Screw

ON

Figure 3-1. Setup switch

3.1 Software Version and Span State Check

1. With the unit in weigh mode, press and hold the ZERO key.

2. With the

ZERO key held, press and release the POWER key three times.

3. The display will show the software version for two seconds, then show the current span switch state

S-ON or S-OFF).

(
After three seconds, the unit will return to weigh mode.

3.2 Performing a Calibration

The Versa-portion RLP-S/SM must be calibrated in grams or kilograms, and SPEC 01 and 02 must be set for the
gram value (or kg in the SM version). See Section 3.4.

1. With the unit in weigh mode, press and hold the

2. With the

ZERO key held, press and release the POWER key twice, then press and release the TARE key.

The display will show CAL00.

Note

To exit calibration at any time, press the TARE key.

3. Ensure there is no weight on the platter, then press the ZERO key to calibrate the zero point.
The display will show dashes, then CALSP.

4. Place the scale’s full capacity weight on the platter and press the
The display will show dashes, then the weight value.

ZERO key.

ZERO key to calibrate span.

Note

Calibration weight is full grams capacity. Full capacity values are as follows: RLP-6S = 3000 g (3 kg);
RLP-15S = 6000 g (6 kg); RLP-30S = 15000 g (15 kg); RLP-60S = 30000 g (30 kg).

Calibration 3

5. The scale will return to weigh mode automatically. Power down the unit.

6. Calibration is complete.

3.3 Enclosure Security

After an NTEP inspector has examined the unit, he/she will install security cables through three bolts on the
underside of the scale. These cables prevent the unit from being tampered with by an unauthorized individual. If
the cable is removed, NTEP certification will become void.

Figure 3-2. Legal for trade seal; cable passes through three bolts

3.4 Setting the SPEC Value

The SPEC value is used to specify decimal point position, minimum display, net/gross multi-interval, resolution,
weight single or multi-interval, decimal point figure, negative weight display mask, IR mode protection (SPAN
switch must be turned on to allow calibration), start range (amount of weight that can be on the scale when it is
turned on), re-zero range, manual tare cancellation, tare subtraction, tare accumulation, auto tare, weight reset,
tare auto clear, zero tracking, re-zero, and the

1. Press the setup switch (see Figure 3-1).

2. With the unit in weigh mode, press and hold the

3. With the

ZERO key held, press and release the TARE key, then press and release the POWER key twice.

The SPEC number is displayed.

4. To increment the SPEC setting value, press the

5. Press the

6. Press the

7. Press the

SPEC Number Bit 2 Bit 1 Bit 0

ZERO key to save data and increase the SPEC count.
ZERO key to advance to the next SPEC.
TARE key to store SPECs and return to weigh mode.

00 Decimal point position

000 - None
001 - 2nd digit (0.0)
010 - 3rd digit (0.00)
011 - 4th digit (0.000)
100 - 5th digit (0.0000)
101 ~ 111 - Not used

01 Minimum display

00 - 1
01 - 2
10 - 5
11 - 10

UNIT key function. See Table 3-1 on page 4.

ZERO key.

POWER key. Refer to Table 3-1.

Net/gross multi-interval
0 - Gross
1 - Net

Table 3-1. SPEC number and bit explaination (defaults are bold)

4 Versa-portion RLP-S/SM Operation Manual

SPEC Number Bit 2 Bit 1 Bit 0

Note

02 Resolution Selection

00 - 1/2000

01 - 1/3000

10 - 1/6000
11 - 1/7500

03 Decimal point figure for numeral

0 - Period

1 - Comma

04 Start range (amount of weight that can be on the scale when it is

turned on; if there is more weight than allowed, the display will show
all 8s)
00 - ±10% F.S. 10 - ±3%F.S.
01 - ±5% F.S. 11 - ±2%F.S.

05
Not NTEP
Approved

06 Auto tare clear when rezero

07 Zero tracking when Tare

08 Unit key (Not used on Versa-portion RLP-SM)

Manual tare cancellation

0 - Allow

1 - Prohibit

0 - Allow

1 - Prohibit

0 - Allow

1 - Prohibit

000 - No
001 - For g and lb conversion
010 - Not used

011 - G, lb and oz

100 - 111 Not used

Negative weight display mask
0 - Minus gross > 9e

1 - Minus gross weight

Tare subtraction

0 - Allow

1 - Prohibit

Weight reset when tare

0 - Allow

1 - Prohibit

Re-zero function

0 - Allow

1 - Prohibit

Weight single interval or multi-interval

0 - Single interval

IR (inter resolution) mode protected by
SPAN SW (SPAN switch must be
turned on for calibration)
0 - No

1 - Yes

Re-zero range

0 - ±2% F.S.

1 - ±3% F.S.

Tare accumulation

0 - Allow

1 - Prohibit

Tare auto clear
(Greater or equal to Gross 21e and
greater or equal toNet 5e)
0 - Allow

1 - Prohibit

Additional zero for weight when only
fixed zeros are displayed (V1.02 and
above)

0 - Allow (NTEP)

1 - Prohibit

Table 3-1. SPEC number and bit explaination (defaults are bold) (Continued)

3.5 Internal Count and A/D Count Display

1. With the unit in weigh mode, press and hold the ZERO key.

2. With the
The display will show

3. Press the

4. To return to weigh mode, press the

ZERO key held, press and release the TA RE key twice, then press and release the POWER key.

,,,,,0,.

POWER key to display the A/D count.

TARE key.

(G) uppercase is the abbreviation for gross.

(g) lowercase is the correct abbreviation for grams.

Calibration 5

4.0 Appendix

4.1 DC Battery Pack

4.1.1 Battery Pack Replacement/Installation

An optional DC battery pack (PN 108516) for the Versa-portion RLP-S/SM is available and can be purchased
from RLWS to ship with the scale or retrofit in the field. The rechargeable 6V 5.0 AH battery pack allows for up
to 60 hours of scale use without an AC power supply (with display set to Dimmer Level 2). It is located in the
bottom of the scale base. Use the following procedure to install or replace the battery pack.

1. Unplug the scale from power source.

2. Place scale its left side.

Caution

Do not turn the scale upside down. Always work with the scale on its side. Damage to the load cell can
occur if the scale is turned upside down.

3. Unscrew the Phillips-head screws holding the battery compartment door closed.

4. Unscrew the two screws holding on the battery holding bracket and remove the bracket.

5. If you are removing a battery previously installed, remove the battery from its compartment, then
disconnect the black (-) and red (+) electrical leads from the battery. If you are installing a new battery,
go to step 6.

6. Attach the red lead to the positive (+) terminal of the new DC battery pack, and the black lead to the
negative (-) terminal. Place new DC battery pack in battery compartment.

7. Replace the battery holding bracket and fasten it with its two screws.

8. Replace the battery compartment door and fasten it with the screws removed in Step 3.

9. Put the scale back upright on its feet.

10. Press the

4.1.2 Battery Charging

POWER key located on the front of the scale.

A fully charged battery allows for approximately 60 hours of continuous use. When the battery is low, the battery
indicator light will light up. To charge the battery, plug in the AC power cord. Charge time is 8-10 hours.

4.2

Error Messages

Display Description Solution

8 8 8 8 8 8 The scale is not steady. Place the scale on a firm, flat base.

O F The weight exceeds capacity + 9d, or something is on the platter

when it was powered on.

U F The negative weight exceeds the display limit. Re-zero or cycle power.

E r r o r An error has occured in maintenance mode. Repeat the operation.

E R R 01 There is an A/D error. Contact the scale dealer or RLWS.

E R R 02 There is a data flash erase error. Contact the scale dealer or RLWS.

E R R 03 There is a data flash program error. Contact the scale dealer or RLWS.

Remove any items from the platter and cycle power.

6 Versa-portion RLP-S/SM Operation Manual

Table 4-1. Error Messages

5.0 Specifications

t

/

"

5

*

0

/

"

-

$

0

/

'

&

3

&

/

$

&

t

0

/

8

&

*

(

)

5

4

"

/

%

.

&

"

4

6

3

&

4

Measurement

Canada

Approved

Caution

Display

LED, 6 digits

Capacity

RLP-6S 6.000 lb x 0.002 lb; 3000 g x 1 g;

60.00 oz x 0.02 oz

RLP-15S 15.000 lb x 0.005 lb; 6000 g x 2 g;

150.00 oz x 0.05 oz

RLP-30S 30.00 lb x 0.01 lb; 15000 g x 5 g ;

300.0 oz x 0.1 oz

RLP-60S 60.00 lb x 0.02 lb; 30000 g x 10 g ;

600.0 oz x 0.2 oz

Versa- portion RLP- SM

RLP-3SM 3 kg x 1 g
RLP-6SM 6 kg x 2 g
RLP-15SM 15 kg x 5 g
RLP-30SM 30 kg x 10 g

Display Indicators

Ounces, Grams, Pounds, NET, Center of Zero, Battery Usage

Versa- portion RLP- SM

Kilograms, NET, Center of Zero, Battery Usage

Keyboard

REZERO key, TARE key, ON/OFF key

Resolution

Display Resolution 1/3000
Internal Resolution 1/90,000

Capacity/Minimum Graduation/Tare Range

Max

Capacity

3 kg 20 g 1 g (1e = 30IR) 0 - 1.499 kg

6 kg 40 g 2 g (1e =30IR) 0 - 2.998 kg

15 kg 100 g 5 g (1e =30IR) 0 - 7.495 kg

30 kg 200 g 10 g (1e =30IR) 0 - 14.99 kg

Min Capacity Min Graduation Tar e R an ge

Certifications and Approvals

Versa-portion (US version)

CoC Number 10-068

AM-10-0054

Versa- port ion RLP- SM

(pending)

OIML

Platter Size

237.2 mm x 298.0 mm

Operating Humidity

15 to 85% relative humidity

Operating Temperature

14° F to 104° F (-10° C to +40° C)

Power Consumption

18W when using AC power
3W when using rechargeable battery
Battery life: 60 hours of continuous usage

Power Source

DC 12V/1.5A, DC 6V5Ah rechargeable battery (Optional)

Dimensions

251.6 mm x 289.7 mm x 134.6 mm

Package Weight

6.3 kg

Package Size

377 mm x 337 mm x 245 mm

Rating

IP68

Do not use any parts on this scale that
may contain lead.

Specifications 7

Versa-portion RLP-S/SM Limited Warranty

Rice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by a
Distributor or Original Equipment Manufacturer (OEM) will operate per written specifications as confirmed by
the Distributor/OEM and accepted by RLWS. All systems and components are warranted against defects in
materials and workmanship for one year.

RLWS warrants that the equipment sold hereunder will conform to the current written specifications authorized
by RLWS. RLWS warrants the equipment against faulty workmanship and defective materials. If any equipment
fails to conform to these warranties, RLWS will, at its option, repair or replace such goods returned within the
warranty period subject to the following conditions:

• Upon discovery by Buyer of such nonconformity, RLWS will be given prompt written notice with a
detailed explanation of the alleged deficiencies.

• Individual electronic components returned to RLWS for warranty purposes must be packaged to
prevent

electrostatic
publication, Protecting Your Components From Static Damage in Shipment, available from RLWS
Equipment Return Department.

• Examination of such equipment by RLWS confirms that the nonconformity actually exists, and was
not

caused

by accident, misuse, neglect, alteration, improper installation, improper repair or

improper testing; RLWS shall be the sole judge of all alleged non-conformities.

• Such equipment has not been modified, altered, or changed by any person other than RLWS or its
duly authorized repair agents.

• RLWS will have a reasonable time to repair or replace the defective equipment. Buyer is responsible
for shipping charges both ways.

• In no event will RLWS be responsible for travel time or on-location repairs, including assembly or
disassembly of equipment, nor will RLWS be liable for the cost of any repairs made by others.

discharge (ESD) damage in shipment. Packaging requirements are listed in a

HESE WARRANTIES EXCLUDE ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT

T

LIMITATION WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

. NEITHER

RLWS NOR DISTRIBUTOR WILL, IN ANY EVENT, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

RLWS

REPAIR OR REPLACEMENT OF SUCH GOODS

ALL OTHER CLAIMS TO WARRANTY

S

WARRANTY CLAIMS

N

WARRANTY SHALL HAVE ANY LEGAL EFFECT UNLESS MADE IN WRITING AND SIGNED BY A CORPORATE

OFFICER OF

AND BUYER AGREE THAT RLWS’S SOLE AND EXCLUSIVE LIABILITY HEREUNDER IS LIMITED TO

. IN ACCEPTING THIS WARRANTY, THE BUYER WAIVES ANY AND

.

HOULD THE SELLER BE OTHER THAN RLWS, THE BUYER AGREES TO LOOK ONLY TO THE SELLER FOR

.

O TERMS, CONDITIONS, UNDERSTANDING, OR AGREEMENTS PURPORTING TO MODIFY THE TERMS OF THIS

RLWS AND THE BUYER.

© 2011 Rice Lake Weighing Systems, Inc. Rice Lake, WI USA. All Rights Reserved.

RICE LAKE WEIGHING SYSTEMS • 230 WEST COLEMAN STREET • RICE LAKE, WISCONSIN 54868 • USA

8 Versa-portion RLP-S/SM Operation Manual