Rice Lake TicketPress User Manual
US 800-472-6703 International 715-234-9171
TicketPress™ Ticket Printer
Note
Warning
POWER
PRINT
POWER
Print Line
Indicator
Ticket Edge
Guide
Knob
Grasp Here
Grasp Here
Printer Operation
9. To update
Date use to change highlighted portion
Operator Card
Electric shock hazard.
Only qualified personnel should operate
the equipment.
Refer all repairs and modifications to
your distributor or service technician.
Failure to heed may result in serious
injury or death.
Control Panel Features
LCD Display and Status Indicators
LCD Display Two line by sixteen-character display used to
POWER
Indicator
FAULT
Indicator
Audible Alarm Sounds when a fault condition has occurred.
Front Panel Control Buttons
Increment
Enter
PN 129651 April 2012
convey current printer status information and
for printer configuration.
Off – Printer is off.
On – Printer is on and ready to receive data.
Flashing:
Random pattern = Data being received from
host.
Steady pattern = Printer is in setup mode,
input data is ignored.
Off – The printer is operating normally.
On – The printer has detected a fault condition
t prevents printing. See Operator’s Manual.
tha
Press to turn the printer on.
Press and hold for approximately five seconds
rn the printer off.
to tu
These buttons are only used to initiate a self
for printer configuration. See Operators
test or
Manual
The Print button action is determined by the
current settings and whether a fault condition
currently exists. See Operators Manual.
1. Press
to turn printer on.
2. Insert a ticket.
3. Send print from weight indicator.
If user activates print from TicketPress, cable
modification may be required. (See Operators
Manual PN 128
032).
Insert ticket
1. Slide ticket into the printer as shown above.
2. Align right edge of ticket with the edge guide.
3. Slide ticket in far enough to align desired print position
th print line indicator.
wi
If the TicketPress receives data t
o print and no ticket has been
inserted, the printer will sound a long beep and display
on the display. If this happens:
Out
1. Make sure a ticket has been inserted, is aligned with the
cket edge guide, and inserted far enough to be aligned
ti
with the print line indicator.
2. When the ticket is inserted properly, the printer will
omatically continue printing.
aut
Time and Date
1. Turn the printer off.
2. Press and hold
, press and release
to hold until Entering Setup Menus is displayed.
3. Options will display, press and hold
seconds to enter menu.
4. Press
Loc, Time, Date, ID.
to cycle through choices and to select
5. Press to select print position, if needed.
6. Press
7. To update
and
8. Press and hold
until time is displayed.
Time use to change highlighted portion
to move to next portion.
to advance.
, continuing
POWER
about 2
Ticket
and
10.When complete, press
to move to next portion.
until Option Menu is
displayed. Screen will display time and date updated.
11.Press
until Exit Setup Menus, Save Changes is
displayed.
12.Press
again to exit menus and save changes.
Printer Self Test & Monitor Mode
The printer performs many self-diagnostics each time power
is applied. If you wish to perform an actual printing test
and/or use the Hex Dump mode to diagnose host data sent to
the printer, use the following steps.
1. Make sure the printer is powered off.
2. Make sure the printer has a ribbon installed and a blank
ticket loaded. This ticket must be at least 4” wide and 9”
ou may also use a blank piece of copier/laser
long. Y
paper.
3. Press and hold
4. Turn the printer on while continuing to hold .
5. When printer beeps, release
. The printer will
automatically begin to print. Display screen shows
entering
Self Test Mode.
6. After the self test has completed, the printer is left in
nitor mode. Insert a blank sheet to print subsequent
Mo
jobs in Hexadecimal representation for diagnostic
purposes.
7. To exit the Self Test & Monitor mode, turn the printer
f.
of
Replace Ribbon Cartridge
1. Open printer cover to expose the print head area.
2. Remove used ribbon by grasping side as indicated below.
3. Take new ribbon cartridge (PN 128031) from its
aging and turn knob in the direction indicted until
pack
fabric is taut.
4. Orient and press the ribbon onto the carriage as shown
ow.
bel
Refer to Operator’s Manual (PN 128032) for detailed instructions
Manuals are available on our web site at
www.ricelake.com/manuals
PN 129651 April 2012
US 800-472-6703 International 715-234-9171
Refer to Operator’s Manual (PN 128032) for detailed instructions
Manuals are available on our web site at
www.ricelake.com/manuals
Loading...