Rice Lake 1280 Technical Manual

Download

Page 1

1280 Enterprise Series

Color Touchscreen Indicator

Version 1.07

Technical Manual

™

PN 167659 Rev G

Page 2

An ISO 9001 registered company

Rice Lake Weighing Systems® is a registered trademark of

Rice Lake Weighing Systems.

All other brand or product names within this publication are trademarks or

registered trademarks of their respective companies.

All information contained within this publication is, to the best of our knowledge, complete and accurate

at the time of publication. Rice Lake Weighing Systems reserves the right to make changes to the

technology, features, specifications and design of the equipment without notice.

The most current version of this publication, software, firmware and all other product updates can be

found on our website:

www.ricelake.com

Page 3

Contents

Technical training seminars are available through Rice Lake Weighing Systems. Course descriptions and dates can be viewed at www.ricelake.com/training or obtained by calling 715-234-9171 and asking for the training department.

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2 Weigh Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.3 Numeric/Alpha Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Main Menu User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4.1 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4.2 Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4.3 Audit Trail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4.4 Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.4.5 Return to Weigh Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.5 Indicator Virtual Keypad Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.5.1 Toggle Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.5.2 Zero Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.5.3 Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.5.4 Print Ticket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.5.5 Accumulator Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.5.6 Peak Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.6 Indicator Keypad Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6.1 Navigation Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6.2 Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6.3 Toggle Gross/Net Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6.4 Toggle Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6.5 Zero Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6.6 Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.6.7 Print Ticket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.6.8 Accumulator Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.7 Alibi Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.8 Peak Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.9 Rate Of Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.10 Setpoint Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.11 Softkey Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.11.1 Checkweigher Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.11.2 Counting Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.11.3 Recipe Batching Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.11.4 Truck In/Out Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.1 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.2 Mounting/Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.2.1 Universal Mount Enclosure with Tilt Stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.2.2 Wall Mount Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.2.3 Panel Mount Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

2.3 Option Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

2.4 Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2.4.1 Grounding Through Cord Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2.4.2 Panel Enclosure Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2.4.3 Load Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2.4.4 Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

2.4.5 CPU Digital I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Page 4

Product Name

Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars

2.5 Wiring Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.6 Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.7 CPU Board Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

2.8 Power Supply Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

2.9 Replace Fan Plate and Back Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

2.10 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

2.11 Label Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.0 Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

3.1 Access Setup Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

3.2 Access Configuration Menu – Sealed Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

3.3 Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

3.3.1 Configuration Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

4.0 Scale Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

4.1 Scale Kind. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

4.1.1 Scale Alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

4.1.2 Scale Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

4.1.3 Split Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

4.2 Scale Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

4.2.1 Standard Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

4.2.2 Multi-Point Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4.2.3 Last Zero Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4.2.4 Temporary Zero Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

4.2.5 Theoretical Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

4.3 Scale Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

4.3.1 Adaptive Digital Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

4.3.2 Three Stage Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

4.4 Scales Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

4.5 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.6 Serial Scale Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.6.1 Legal for Trade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.6.2 Industrial Scales. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.6.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

5.0 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

5.1 Serial Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

5.2 Ethernet Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

5.2.1 Using an Internet Browser as a Remote Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

5.2.2 Resetting the Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

5.2.3 Wired Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

5.2.4 Wi-Fi Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

5.2.5 Wi-Fi® Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

5.2.6 TCP Command Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

5.2.7 Stream Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

5.2.8 TCP Client 1 & 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

5.3 Fieldbus Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

5.3.1 Data Swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

5.4 iQube2 Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

6.0 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

6.1 Softkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

2 Visit our website www.RiceLake.com

Page 5

Contents

6.1.1 Enable/Disable Softkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

6.1.2 Predefined Softkeys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

6.1.3 Database Softkey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6.1.4 LaserLight Softkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6.2 General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

6.2.1 Local/Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

6.3 Regulatory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

6.3.1 Parameters Available in all Regulatory Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

6.4 Passwords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

6.5 Locale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

6.5.1 Default Weigh Mode Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

6.6 Contact Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

6.7 Advanced Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

6.8 View Alibi Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

7.0 Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

7.1 Print Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

7.1.1 Default Print Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

7.1.2 Set Destination 1 and 2 Print Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

7.1.3 Print Format Tokens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

7.2 Strteam Format Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

7.2.1 Stream Format Tokens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

8.0 Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

9.0 Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

9.1 Analog Output Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

10.0 Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

10.1 Select Setpoint for Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

10.2 Setpoint Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

10.2.1 Targets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

10.2.2 Preacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

10.2.3 Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

10.2.4 Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

10.2.5 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

10.3 Batch Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

10.3.1 Batching Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

11.0 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

11.1 Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

11.1.1 Touchscreen Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

12.0 Option Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

12.1 Hardware Serial Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

12.2 Option Card Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

13.0 Importing/Exporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

13.1 Importing Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

13.1.1 Importing Built-in iRite Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

13.1.2 Importing Revolution Files from a Flash Drive or Micro SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Page 6

Product Name

Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars

13.2 Importing iRite™ Programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

13.2.1 Importing Built-in iRite Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

13.2.2 Importing iRite from a Flash Drive or Micro SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

13.2.3 Downloading from Revolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

13.3 Importing Database Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

13.3.1 Importing Databases from a Flash Drive or Micro SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

13.3.2 Downloading Databases to the 1280. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

13.4 Exporting Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

13.4.1 Exporting to Flash Drive or Micro SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

13.4.2 Uploading to Revolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

13.5 Exporting Database Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

13.5.1 Exporting Database to Flash Drive or Micro SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

13.5.2 Saving Databases from the 1280 to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

13.6 Exporting Diagnostic Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

13.7 Connecting to the Indicator from Revolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

13.8 Loading New Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

13.8.1 Check Current Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

13.8.2 Download Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

13.8.3 Upload Firmware to 1280. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

13.8.4 Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

13.9 Scale Card Version Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

13.9.1 Updating Scale Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

13.10 Visual Studio Code – iRite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

13.10.1 Compilation and Deployment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

14.0 Display Editor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

14.1 Configurable Splash Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

14.2 Widgets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

14.2.1 Scale Widgets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

14.2.2 Bitmap Widgets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

14.2.3 Bar Graph Widgets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

14.2.4 Label Widgets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

14.2.5 Symbol Widgets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

14.2.6 Image Widgets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

14.2.7 Chart Widgets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

14.2.8 Line Widgets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

14.2.9 Softkey Widgets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

14.3 Widget Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

15.0 EDP Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

15.1 Key Press Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

15.2 Reporting Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

15.3 Clear and Reset Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

15.4 Parameter Setting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

15.5 1280 Calibration using Serial Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

15.6 Weigh Mode Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

15.7 Batching Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

15.8 Database Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

15.9 iQube2 Configuration Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

16.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

4 Visit our website www.RiceLake.com

Page 7

Introduction

1.0 Introduction

The 1280 Enterprise Series is a color touchscreen, programmable, multi-channel digital weight indicator/controller. Manufactured with industrial-grade components, the 1280 is built to achieve top performance, even in harsh environments. The 1280 features a Freescale i.MX6 microprocessor, Linux-based operating system and 1 GB onboard memory (expandable

with micro SD card). Configuration can be performed using the front panel, serial commands or Revolution For applications using the 1280 indicator as a host device, Version 1.03 or later of the 128 0 indicator software must b e installed.

Custom programs can be written with iRite®, a domain-based programming language based off of Basic, Pascal and Ada— empowering programmers to customize display widgets, store and retrieve data with the onboard datab ase and utilize the 150+ built-in-functions. From tailored basic weighing to complex process automation, the 1280 delivers uncom pro mising speed for today’s most demanding applications as well as vast expandability for future needs.

Manuals can be viewed or downloaded from the Rice Lake Weighing Systems website at Warranty information can be found on the website at www.ricelake.com/warranties

Onboard Features

Features of the 1280 include:

• Support for up to eight scales (combination of analog load cell, total, serial scales or

• Eight programmable Digital I/O bits available on the CPU board (con nector J1) including onboard pulse input pins, with 24 additional per option card

• Two communication ports that support RS-232, RS-485 and RS-422

• T wo USB host ports

• One USB device port

• AC or DC power options

• Ethernet – wired, Wi-Fi and Wi-Fi Direct

•Bluetooth

program scales)

scale software.

www.ricelake.com/manuals

Other Features

• Built in Web Server for remote access to screens

• Configurable print formats can be defined for up to 1000 characters each. Additional print formats can be created with

iRite.

• Truck in/out, recipe batching, counting and checkweighing

• 100 configurable setpoints.

•The 1280 is NTEP, OIML and Measurement Canada certified. See Section 16.0 on page 166 for more information.

iRite programs and source code included.

Three Enclosure Types

•Universal

• Panel Mount with numeric keypad or touch only (7 inch and 12 inch display)

•Wall Mount

Option Cards

The CPU board provides six slots for installing scale or other option cards. Available option cards include:

• Single- and dual-channel scale cards to drive up to sixteen 350 ohmload cells per card. Scale cards support both 4- and 6-

wire load cell connections.

• Single- and dual-channel analog output card for 0–10 VDC, 0–20 mA or 4-20 mA tracking of gross or net weight values.

• 24-channel digital I/O expansion card

• Dual channel serial port card (with RS-232, RS-422 and RS-485)

• Dual channel analog input card for 0–100 mV, 0-10 VDC, 0–20 mA or 4-20 mA

• 4-channel relay card

• CompactCom card that supports EtherNet/IP™, DeviceNet™, ProfiNet, Profibus® DP Modbus TCP, EtherCAT and PowerLink networks.

Page 8

1280 Series Color Touchscreen Indicator

DANGER

WARNING

CAUTION

IMPORTANT

WARNING

1.1 Safety

Safety Signal Definitions:

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided could result in serious injury or death. Includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.

Indicates information about procedures that, if not observed, could result in damage to equipment or corruption to and loss of data.

General Safety

Do not operate or work on this equipment unless this manual has been read and all instructions are understood. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake Weighing Systems dealer for replacement manuals.

Failure to heed may result in serious injury or death. Some procedures described in this manual require work inside the indicator enclosure. These procedures are to be performed by

qualified service personnel only. Do not allow minors (children) or inexperienced persons to operate this unit. Do not operate without enclosure completely assembled. Do not place fingers into slots or possible pinch points. Do not use this product if any of the components are cracked. Do not make alterations or modifications to the unit. Do not remove or obscure warning labels. Do not submerge. Before opening the unit, ensure the power cord is disconnected from the power source.

2 Visit our website www.RiceLake.com

Page 9

1.2 Weigh Mode

9 10

12 13

Note

The display illustrations in this manual are for reference only, they can be different from default illustrations depending on the colors, graphics or programs that have been loaded.

Introduction

Figure 1-1. Weighing Mode Display Screen

Item No. Description

Status Bar 1 Menu key – Press to enter setup menus and audit trail information.

2 3 Current time – Press to set the time.

4 Current date – Press to set the date. 5 Scale arrows – Use to scroll through the attached scales in the current scale area (up to eight scales).

Weight Display Area 7 Current scale – Scale number currently displayed 8 Gross/Net – Current weighing mode 9 Standstill icon – Indicates scale is stable 10 Tare – Weight of tare in system 11 Weight reading for current scale 12 Unit of measure 13 Capacity and division size (values shown are for illustration only) 14 Application area – Contains configuration of widgets (text boxes, bar graphs, icons, etc) 15 Display line for text (messages from an iRite program) 16 System messages or status (batch running, print queued, etc) Softkeys

Virtual keypad button - Press to enter. Zero

keys located on the front panel

Wi-Fi Symbol - Indicates Wi-Fi signal strength. When faded, Wi-Fi is not connected or out of range. Press on the symbol to bring up the

Wi-Fi, Wi-Fi Direct and Bluetooth screen.

Five softkeys can be selected from the default list, or can be user defined custom text and iRite programming functionality. These can be removed for more screen customization.

When a system reset is performed (Version 1.05 and later) the Weigh Mode display is populated with a scale widget and a softkey widget. This gives end users access to softkey setup without having to use EDP commands or revolution.

and the ability to restart all network connections from the network information

, Tare, Gross/Net, Print and Units keys are identical to the physical

Network Information Screen which includes information on Wired Ethernet,

Table 1-1. Weigh Mode Display

Page 10

1280 Series Color Touchscreen Indicator

1.3 Numeric/Alpha Entry

When data entry is required, a keyboard or a numeric keypad will display on the screen. Ad ditionally, the in dicator’s front p anel is equipped with a numeric keypad.

Figure 1-2. 1280 On-screen Full Keyboard for Alphanumeric Entry

Figure 1-3.

Item No. Description

1280 On-screen Numeric Keypad for Numeric Entry

1 Cancel – Press to exit keyboard 2 Done – Press to complete keyboard entry 3 Clear – Delete everything in the prompt line 4 Backspace – Delete one character at a time

Table 1-2. On-screen Keyboard Descriptions

4 Visit our website www.RiceLake.com

Page 11

Introduction

Re-Zero

1.4 Main Menu User Interface

The Main Menu allows the operator access to Configuration, Calibration, Setpoint Values, Audit Trail and Language. From the weigh mode press to enter the main menu.

Item No. Description

Configuration – may be unaccessible to the operator by password protection

Calibration – allows the operator to perform a calibration

Setpoint Values – access to setpoint targets and settings

Audit Trail – view number of configuration and calibration edits, plus the last calibration date

Language – allows scale language to be changed

Table 1-3. Main Menu User Interface

1.4.1 Calibration

Use the following steps to perform a standard calibration on a scale.

1. Select the scale to be calibrated and enter the calibration menu.

2. Press .

3. Select the method of calibration. Press .

4. Select whether or not chains, hooks or other items used for applying weights will be u sed during calibration. Press

5. Remove all weight from the scale except for chains and hooks (if used).

6. Press . The current weight and Zero Calibration Complete displays.

7. Press .

8. Enter Span weight for the value of the calibration test weights that will be used to calibrate the scale. This is required

prior to running the span calibration.

9. With the test weight on the scale platform and the test weight value entered into the calibration weight window, the

corresponding scale span value is ready to be calibrated.

10. Press . The current span weight displays.

11. Press . Calibration results are displayed.

12. Press . Display returns to the Calibration menu.

13. The re-zero function is used to remove a calibration offset when hooks or chains are used to hang the test weights

during both zero and span calibration. If hooks or chains were used during calibration, remove these and the test weights from the scale.

14. With all weight removed, p r ess .

Page 12

1280 Series Color Touchscreen Indicator

Figure 1-4. Audit Trail Screen

1.4.2 Setpoints

Targets are a set of values that when met, cause the setpoint to trip.

Parameter Default Description

Setpoint Value:

Value 0

Source Scale 1 Select Scale 1-8.

Trip Higher

Settings allow the operator to select the mode of the setpoint (batch or free-running). If enabled, it can be accessed by softkey, for defini

ng a name and optional prompt.

Parameter Default Description

Batch Off Specifies whether the setpoint is used as a batch (On) or continuous (Off) setpoint Access Enable On Turns the setpoint on or off

Alias — Enter a name for the setpoint Prompt — Alphanumeric message or prompt that can be displayed in a label widget

Weight-based – specifies the target weight value, 0–9999999 Time-based – specifies time in 0.1 second intervals, range 0–65535 Counter – specifies the number of consecutive batches to run, range 0–65535

Specifies if the setpoint is satisfied when the weight is higher or lower than the setpoint value, within a band established around the value, or outside of that band. In a batch sequence with:

Trip = Higher – the associated digital output is active until the setpoint value is exceeded. Trip = Lower – the output is active until the weight goes below the setpoint value. Trip = Inband – the setpoint is satisfied when the weight is within a band established around the value. Trip = Outband – the setpoint is satisfied when the weight is outside a band established around the value,

excluding the value.

Table 1-4. Target Parameters

On Specifies the access allowed to setpoint parameters shown by pressing the Setpoint softkey in weigh mode.

If set to Off, values can be displayed but not changed. If set to Hide, values do not show.

Table 1-5. Setpoint Parameters

1.4.3 Audit Trail

Audit trail support provides tracking information for configuration and cal ibration events. A separate calibration and configuration counter is provided for each scale; a single system configuration counter tracks all global changes that are applied to multiple scales.

To prevent misuse, unsaved configuration or calibration changes are counted as change events; restoration of the previous

d co

save Select to view the legally relevant version, the configuration

coun

nfiguration or calibration is also counted.

ters and the calibration counters.

1. Press to send the audit trail data

out the configured communications port (default is port 1).

2. Select

to return to the weigh

mode.

6 Visit our website www.RiceLake.com

Page 13

1.4.4 Language

Figure 1-6.

Busy Wheel

The

1280

has 16 language choices, setting the language is only available in weigh mode. Configuration mode remains in English.

Figure 1-5. Language Selections

1. Press to display the list of available languages.

2. Select the desired language.

Introduction

3. Press to save the selection and return to the weigh mode.

1.4.5 Return to Weigh Mode

When settings are complete for Configuration, Calibration or Setpoint Values, press . The Busy Wheel will

display for a few seconds, then the display will go back to the weigh mode.

1.5 Indicator Virtual Keypad Operation

The 1280 comes equipped with a virtual keypad. .The functionality of the Zero, Tare, Gross/Net, Print and Units keys is identical to the physical keys located on the front panel of the keyed 1280.

Figure 1-7. Virtual Keypad Functions

The Keyed Tare key is equivalent to the keyed tare softkey that already exists. By pressing Keyed Tare, an onscreen numeric keypad is displayed so that the user can key in a tared value.

Toggle Gross/Net Mode

Pressing toggles the display mode between gross and net.

• I f a tared value is in the system, Net is d

• I f there is no tare in the system, Gross is displayed

isplayed (net equals gross minus tare)

Page 14

1280 Series Color Touchscreen Indicator

1.5.1 Toggle Units

Pressing toggles between primary, secondary and tertiary units.

1.5.2 Zero Scale

Use the following steps to zero the scale (if it is within the acceptable zero range).

1. In gross mode, remove all weight from the scale

2. Press . When displays, the scale is zeroed.

and wait for to display.

1.5.3 Tare

Use the following instructions to acquire a tare, remove a stored tare and enter a tare using the display softkeys.

Acquire Tare

Used to store the weight currently on the scale as a tare weight and switch to ne t mode.

1. Place a container on the scale and wait for to display.

2. Pres

s . Net displays, indicating the weight has been tared.

Remove Stored Tare Value

Used to remove a stored tare value.

1. Remove all weight from the scale to show gross zero.

2. When

Alternatively, remove a stored tare value using a keyed tare of zero. See Keyed Tare, below.

displays, press (in OIML mode, press ). Gross displays.

Keyed Tare

Used to add a keyed tare.

1. Press the keyed tare virtual key . Enter the value from the on screen numeric keypad and press Done.

1.5.4 Print Ticket

Pressing sends the gross or net ticket format to the configured serial, USB or Ethernet port associated with its ticket format. When displaying the accumulator, it

To print tickets using auxiliary formats (1-20), press the softkey, which is not part of the virtual keypad.

1. Wait for to display.

3. Enter an auxiliary format number (1-20) and press done to sent the date to the serial port.

s .

Pres

prints the accumulator format.

8 Visit our website www.RiceLake.com

Page 15

Introduction

1.5.5 Accumulator Functions Acquiring Weight

If the accumulator is enabled while in configuration, weight is accumulated whenever a print operation is performed by:

•Pressing

ctivating a digital input print

• A

• Receiving a KPRINT serial command

• iRite calling the PRINT () function

• Activating the accumulator with a setpoint

The scale must return to zero be

the next accumulation.

fore

Display or Clear the Accumulator

• A softkey can be programmed for each function

• A Display or Clear Accumulator Digital Input can be activated (ClearAccum0 iRite API, can be cleared with a setpoint)

• A serial command can be sent

Print the Accumulated Value

To print the accumulated value, press while displaying the accumulator.

1.5.6 Peak Hold

Peak hold is used to determine, display and print the greatest weight reading during a weighing cycle.

There are three types of peak hold: automatic, manual and bi-directional.

To use the peak hold function:

1. Tare the scale to put it into net mode.

. Increase the weight. As the weight increases, the indicator will capture and hold the highest weight recorded.

3. Press to see the real live weight (as opposed to the peak hold weight).

4. Press or to clear the peak hold (unless set to automatic mode, in which case it clears automatically).

Indicator Softkey Setup

The standard 7 inch panel mount has front panel ke ys, navigation softkeys and a virtual keypad. The 7 inch and 12 inch keyless panel mounts only support a virtual keypad (Figure 1-7).

1. To enter navigation softkey designations for the 7 inch panel mount, navigate from the 1280 main menu to

Configuration - Features - Softkeys.

2. Add the navigation softkey designation by cli cking . Scroll through the list to select the softkey designation, pressing

3. The softkeys appear on the main menu screen.

Done when complete.

Figure 1-8. Seven Inch Navigation Softkeys

Page 16

1280 Series Color Touchscreen Indicator

Display/Virtual keypad

Numeric Keypad

Navigation Keys

ENTER

1.6 Indicator Keypad Operations

1.6.1 Navigation Keys

Navigation keys are primarily linked to iRite handlers. If no iRite handlers exist, the navigation keys toggle through a selection of displayed scales.

1.6.2 Numeric Keypad

Use the numeric keypad for entering numbers or keyed tares. Press to backspace when entering numbers/letters.

Press to save entries from the numeric keypad.

1.6.3 Toggle Gross/Net Mode

Pressing toggles the display mode between gross and net.

1.6.4 Toggle Units

Pressing toggles between primary, secondary and tertiary units.

1.6.5 Zero Scale

Use the following instructions to zero the scale (if it is within the acceptable zero range).

1. In gross mode, remove all weight from the scale and wait for to display.

Figure 1-9. 1280 Front Panel

•If a tared value is in the system, Net is d

•If there is no tare in the system, Gro

ss is displayed.

isplayed (net equals gross minus tare).

2. Press . When displays, the scale is zeroed.

10 Visit our website www.RiceLake.com

Page 17

1.6.6 Tare

Use the following instructions to acquire a tare, remove a stored tare and enter a tare usi ng the keyboard.

Acquire Tare

Used to store the weight currently on scale as tare weight and switch to net mode.

1. Place container on scale and wait for to display.

Introduction

2. Pres

. Net displays indicating the weight has been tared.

Remove Stored Tare Value

Used to remove a stored tare value.

1. Remove all weight from the scale to show gross zero.

2. Whe

Alternatively, remove a stored tare value using a keyed tare of zero. See “Keyed Tare” below.

n displays, press (in OIML mode, press ). Gross displays.

Keyed Tare

Used to add a keyed tare.

1. Enter a value from the numeric keypad or an attached keyboard.

2. Pres

. Net displays indicating the keyed tare weight is in the system.

1.6.7 Print Ticket

Pressing sends the gross or net ticket format to the configured serial, USB or Ethernet port associated with its ticket format. When displaying the accumulator, it prin To print tickets using auxiliary format

1. Wait for to display.

2. Enter

an auxiliary format (1-20).

s (1-20), enter the format number with the numeric keypad.

ts the accumulator format.

3. Press to send data to the serial port.

1.6.8 Accumulator Functions Printing While in Accumulate

If the accumulator is enabled, weight is accumulated whenever a print operation is performed by:

•Pressing the

• Activating a digital input print

• Receiving a KPRINT serial command

• iRite calling the

• Activating the accumulator setpoint

The scale must return to zero before

Print key

PRINT ( ) function

the next accumulation.

Display or Clear the Accumulator

• A softkey can be programmed for each function

•A Display or Clear Accumulator Digital Input can be activated

• A serial command can be sent

Page 18

1280 Series Color Touchscreen Indicator

Print the Accumulated Value

To print the accumulated value, press while displaying the accumulator.

1.7 Alibi Storage

Alibi storage is a database of past transactions listed by date. This allows previous print transactions to be recalled and reprinted. Alibi storage is enabled using the Features menu in configuration mode. Print transactions can be recalled by assigning a softkey to Alibi.

1. Press the

2. Use the arrows to scroll to the record required.

3. Press

4. Repeat steps 1-3 until all records required have been printed.

5. When all records required have been printed, press

Alibi softkey.

Reprint to print the record.

Done.

1.8 Peak Hold

Peak hold is used to determine, display and print the greatest weight reading during a weighing cycle. There are three types of peak hold: automatic, manual and bi-directional. To use the peak hold function:

1. Tare the scale to put it into net mode.

. Increase the weight. As the weight increases, the indicator will capture and hold the highest weight recorded.

3. Press

4. Press or to clear the peak hold (unless it is set to automatic mode in which case it clears automatically).

to see the real live weight (as opposed to the peak hold weight).

1.9 Rate Of Change

Rate of change is expressed in weight per time unit (weight/time).

Example: lb/sec

To view the rate of change:

1. Press the

2. To return to the live weight, press

Display Rate of Change softkey.

Display Rate of Change again.

1.10 Setpoint Entry

Setpoints can be configured to perform actions or functions based on specified parameter conditions. For more information on setpoints.

To change the setpoint value:

1. Press

2. Press the

3. Press

4. Press the red number of the setpoint in the table. It may be necessary to use the arrows at the bottom of the screen

5. Press

6. Enter the new target value and press

7. Press

8. Press

Setup.

Setpoint Values key in the Main menu or from the black drop down list, or pr ess the Setpoint softkey.

Setpoint 1 to select the setpoint (1-100) for which the target value needs to be changed.

scroll through the setpoints.

Value to bring up the numeric entry keypad.

Done. Settings to toggle between enabled and disabled. Done and Save and Exit.

12 Visit our website www.RiceLake.com

Page 19

Introduction

1.11 Softkey Operations

Softkeys are configured to provide additional operator functions. Softkeys are displayed as digital buttons at the bottom of the touch screen display area. See Figure 1-1 on page 3.

Softkey Description

Blank No softkey available. User Defined 1-10 Up to 10 softkeys can be created using one of the user defined options (22 characters or less available). Time/Date Displays current time and date; allows time and date change. Display Tare Displays tare value in the entry prompt. Display Accumulator Displays accumulator value, if enabled, for the current scale. Display Rate of Change Displays rate-of-change value, if enabled, for the current scale. Setpoint Displays a menu of configured setpoints; allows display and change of some setpoint parameters.

Batch Start Batch Stop Stops an active batch and turns off all associated digital outputs. Requires a Batch Start to resume processing.

Batch Pause

Batch Reset

Select Scale Diagnostics Opens the iQube2 diagnostics screen

Alibi Allows previous print transactions to be recalled and reprinted. Contrast Adjusts the screen backlight intensity. Test Not available in version 1.00. Stop Sends AuxFmt13 out its configured port to display a red light on a LaserLight. Go Sends AuxFmt12 out its configured port to display a green light on a LaserLight. Off Sends AuxFmt14 out its configured port to turn a LaserLight red/green light off. Display Unit ID Displays the Unit ID in the lower left corner of the screen. Zero Zeros the indicator. Gross/Net Toggles between gross and net modes. Tare Tare the scale by using the onscreen numeric keypad Keyed Tare Tare the scale by using the onscreen numeric keypad Units Toggles between primary, secondary and tertiary units. Print Prints the configured print format. Aux Print Auxilliary printing by entering the Auxilary Format number (1-20) using onscreen numeric keypad Screen Display a different screen by entering a value (1-99) and pressing the Screen softkey. Database Accesses the import and export database feature from the weigh mode.

Starts a batch from the current step if a Batch Run digital input is either active or not defined. If a Batch Run digital input is defined and inactive, Batch Start resets the batch to the first step.

Pauses an active batch and turns off all digital outputs except those associated with Concurrent and Timer setpoints. Processing is suspended until the indicator receives a Batch Start signal. Pressing the BATSTRT digital input, BATSTART serial command, Batch Start softkey or the StartBatch function (in iRite) resumes the batch and re-energizes all digital outputs turned off by the Batch Pause.

Stops an active batch and resets the current step to the first batch step. All digital outputs associated with batch setpoints are deactivated. If a batch is stopped or paused, Batch Reset will reset the current step to the first step.

Enter the scale number (using the numeric keypad) to be displayed for multi-scale applications, followed by the select scale softkey.

Table 1-6. Configurable Softkeys

Applications

The 1280 can be used in a variety of applications, including checkweighing, counting, recipe batching and truck in/out. For these frequently used applications, the 1280 includes built-in programs that can be used as-is or customized for specific needs.

1.11.1 Checkweigher Application

The checkweigher application is included with the 1280 standard firmware. This application is a static checkweigher with a stored low and high weight associated with an ID. A di gital output is activated based on the status of the weight. The digital output stores the ID, weight, status (under, accept, or over) and time/date in a database. The print key can be pressed to print the last transaction’s ID, weight, status and time/date. Two softkeys are available:

Item and Setup Menu.

Select an Item

1. Press the Item softkey.

Page 20

1280 Series Color Touchscreen Indicator

Note

ID: 555 Gross: 0.25 lb ACCEPTED

1/1/2015 01:00 PM

2. System prompts Enter ID to Checkweigh. Enter a stored ID with associated low and high weights.

3. The ID, low and high weights are displayed and the system waits for the threshold to be triggered.

Checkweigh

1. When the weight exceeds the threshold weight, the indicator checks that an ID was selected. If an ID has not be selected, the system does nothing. If an ID has been selected, the system waits for standstill and compares the gross or net weight (whichever mode Scale 1 is currently in) against the low and high weights.

• I f the weight is less than the low weight, the system displays Under and turns on the Under output.

• If the weight is more than the high weight, the system displays Over and turns on the Over output.

• If the weight is more than the low weight and less than the high weight, the system displays Accept and turns on the

Accept output.

2. A record will be stored to the database with the ID, the weight, the status (under, accept or over) and time/date.

Status Output

Under 1 Accept 2 Over 3

Table 1-7. Status Output

A database softkey can be used to Import/Export the database from weigh mode.

3. If the auto print feature is enabled (default is disabled), a ticket will print.

Figure 1-10. Checkweigher Ticket

4. When the weight goes under the threshold weight, the display status will clea r; the ID, low and high values will remain ; and all digital outputs will turn off.

Application Setup & Configuration

The Setup Menu softkey is password-protected and offers access to the following:

• Display program name and version

• Display a weight widget

Parameter Default Softkey Description

Allows an operator to change the password that is required for entry into the Setup

System Password “ ” Setup Password

Add/Edit Items -

Delete Items -

Threshold Weight 100 lb Threshold Weight

Auto Print Feature Disabled Auto Print Allows an operator to enable/disable the auto print feature.

Database Setup> Add/Edit Items

Database Setup> Delete Items

Menu. If the password is set to nothing, the system will not prompt for a password when the Setup Menu softkey is pressed.

Allows an operator to add or edit stored IDs with associated low and high weight values.

Allows an operator to delete stored IDs that are no longer used. When the threshold weight is exceeded, the system checks if an ID has been selected.

If an ID has been selected, the system will wait for standstill before reading the weight and categorizing it based on low or high weight. Additionally, if the weight goes below the threshold weight, the system will clear out the last weighment information and turn off the output.

14 Visit our website www.RiceLake.com

Table 1-8. Checkweigher Application Setup and Configuration

Page 21

Introduction

Gross: 10.25 lb APW: .0055 lb Pieces: 1864

1/1/2015 01:00 PM

Parameter Default Softkey Description

Digital I/O Testing -

More-> I/O Test Screen

Table 1-8. Checkweigher Application Setup and Configuration (Continued)

Allows an operator to turn on or off digital outputs.

1.11.2 Counting Application

The 1280 counting application is included with the 1280 standard firmware. This application has two scales, one for sampling and one for counting. Upon startup, the softkeys

Sample Size, Scale Select, APW, Clear Tare and Setup Menu are available.

Select Sample Size

1. Press the Sample Size softkey. The sample size will toggle to five pieces. If pressed again it will toggle to 10 pieces, then 20, then 50, then 100, then 200, then back to five.

2. Press

Sample Size once to enter Sample Size Mode. Press a numeric key followed by the Enter key to enter any

number as the sample size (instead of toggling to one of the choices listed above).

3. Once the correct sample size is displayed in the softkey, press

Enter to calculate the APW based on the current

weight, current scale and current sample size. The number of pieces will display. This number is continuously updated as the weight or scale selected changes.

Select Scale

1. Press the Scale Select softkey to switch between scales.

2. There are two scales available. Typically one is used for sampling (smaller capacity) and one is used for counting (larger capacity). This application works the same for both scales, or if only one scale is used for both sampling and counting. The piece count is always referencing the current scale that is displayed.

Enter APW

Press the APW softkey to enter a new known APW for the current part.

Counting Pieces

The number of pieces will display. This number is continuously updated as the weight, scale selected or mode selected changes. This includes adding pieces or removing pieces, as well as going to a negative net as pieces are removed from a net zero weight. For example, if a full box was placed on the scale,

Tare was pressed to tare off the weight to net zero, and then the

count pieces were removed, the scale would display a negative number.

Figure 1-11. Counting Printed Ticket Example

Application Setup and Configuration

Parameter Default Softkey Description

System Time and Date Current Time/Date Time and Date of that displays on the 1280 .

Allows an operator to change the password that is required for entry into the

System Password “ ” Setup Password

Clear Transactions - Clear Trans Allows an operator to clear the transaction database.

Setup Menu. If the password is set to nothing, the system will not prompt for a password when the Setup Menu softkey is pressed.

Table 1-9. Counting Application Setup and Configuration

Page 22

1280 Series Color Touchscreen Indicator

Note

WARNING

Recipe ID: 1 Recipe Name: Fall Blend

Ingredient Target Actual

--------------------------------Corn 200 lb 192 lb Winter Wheat 300 lb 323 lb Chicory 222 lb 318 lb

Total 722 lb 833 lb

Printed @ 09:36AM 09/15/2014

Figure 1-12. Printed Ticket Example

1.11.3 Recipe Batching Application

The 1280 recipe batching application is included with the 1280 standard firmware. Upon startup, the softkeys Recipe and

Setup Menu are available.

Recall a Recipe

1. Press the Recipe softkey. The system prompts Enter Recipe ID.

2. Enter the recipe ID and press

Enter.

3. If the ID is not found, the system prompts Recipe NOT Found - Retry. If the ID is found, the system recalls all of the recipe information and updates the display.

Process a Batch

• The system will stop the batch if the Emergency Stop switch is turned off while running a batch. The system also turns off

all outputs.

The Emergency Stop Switch is sold separately.

• To restart a batch at a paused step, turn the Emergency Stop switch on and use the Abort-Run-Start switch.

• To abort and exit the batching sequence during a paused ba tch, turn the

Run-Start

switch.

To prevent personal injury and equipment damage, software-based interrupts must always be supplemented by emergency stop switches and other safety devices necessary for the application.

Emergency Stop switch off and use the Abort-

1. Ensure the scale is empty and zeroed.

2. If the displayed recipe is incorrect, perform the recall a recipe procedure described above.

3. Pull out the

Start

Emergency Stop switch and use the Abort-Run-

switch to start.

4. The system will do the following things:

• Verify the weight is below the empty weight value

• Tare the scale

• Activate the output for the first ingredient until its target and

preact weight value is met

• Capture and record the stable weight of the just added

ingredient

• Activate the discharge scale output until the weight drops

below the empty weight value. It will maintain the output for the discharge time. If the discharge time is set to zero, the system will not perform a discharge.

• Print a ticket and return to step 1

16 Visit our website www.RiceLake.com

Page 23

Introduction

Application Setup and Configuration

The Setup Menu softkey is password-protected and offers access to the following:

• Display program name and version

splay a weight widget

• Di

Parameter Default Icon Description

Allows an operator to change the password that is required for entry into the

System Password “ ” Setup Password

Add/Edit Ingredients -

Delete Ingredient -

Add/Edit Recipes -

Delete Recipe Empty Weight 5.0 lb Empty Weight Minimum amount of weight to recognize the scale is empty.

Discharge Time 3.0 Sec Discharge Time Length of time the discharge output remains on after reaching the empty weight. Digital I/O Testing - More-> IO Test Screen Allows operator to turn on/off digital outputs.

Database Setup

-> Add/Edit Ingredients Database Setup

-> Delete Ingredients Database Setup

-> Add/Edit Recipes Database Setup

-> Delete Recipes

Table 1-10. Recipe Batching Application Setup and Configuration

Setup Menu. If the password is set to nothing, the system will not prompt for a password when the Setup Menu softkey is pressed.

Allows an operator to add/edit ingredients from the ingredient database table.

Allows an operator to delete ingredients from the ingredient database table.

Allows an operator to add/edit recipes from the recipe database table.

Allows an operator to delete recipes from the recipe database table.

1.11.4 Truck In/Out Application

The 1280 truck in/out so ftware a pplicatio n is included with the 1280 sta ndard f irmware. See the 1280 Truck In /Out Adde ndum (PN 187311) for complete information on setup and functions.

The Truck In/Out program can control a LaserLight2 Stop/Go program and when the remote display signals green, the truck can pull onto the scale for a transaction. Th

If the scale is equipped with a traffic light, and t The touch widget

Weigh In, Weigh Out, Inbound Trucks, Toggle Light and Setup Menu display on the indicator.

e remote display turns red when the threshold weight is exceeded.

he traffic light turns green, the truck can pull onto the scale for a transaction.

Weigh In

1. Press Weigh In. Enter Truck ID displays.

2. Enter the Truck ID.

3. Press

Enter.

If the ID is found:

•Indicator displays Truc

k Already Weighed In

•Returns to step 2

If the ID is not found, the scale:

•Captures a gross weight from the Scale

•Adds the inbound transaction to the truck register

•Prints a weigh-in ticket, reprint is available until the driver exits the scale

•If a truck exit is required, thetra

•When the weight drops below the Thresh

ht turns green and displays Weigh In Complete - Exit Scale

ffic lig

old Weight, the system returns to Step 1

If the truck Exit is disabled:

•Indicator displays Weigh In

Complete

•Returns back to Step 1

Weigh Out

1. Press Weigh Out. Enter Truck ID displays.

Page 24

1280 Series Color Touchscreen Indicator

2. Enter the truck ID and press Enter. System queries the Inbound database table: If the ID is not found and there is not a keyed tare, the indicator

•Momentarily displays Truck Not Found

•Returns to Enter Truck ID

the ID is found, the system:

•Enter Product ID displ

ays if there are products stored in the database. Enter a stored Product ID and press Enter,

or press Enter to skip. If only one product exists, system goes to customer prompt

•Enter Customer ID d

Enter, or press Enter to skip. If only one customer exists system uses that customer and goes to capturing net

isplays if there are customers stored in the database. Enter a stored Customer ID and press

weight

•Captures a stable GROS

•Does Value Swapping

S weight from the Total Scale.

if enabled in the Setup Menu (not with Keyed Tare)

•Prints a Weigh Out Ticket, reprint is available until the driver exits the scale

•Stores Transaction Record Deletes inbound weight if Stored Tares is disab

led in the Setup Menu (not with Keyed Tare).

Deletes inbound weight if Stored Tares is enabled and Truck ID has a decimal in it.

3. Exit the scale when the light turns green. If the Truck Exit is required:

h Ou

•Indicator displays Weig

•When the weight drops below the Thresh

t Complete - Exit Scale

old Weight system returns to Step 1

If the Truck Exit is disabled:

•Indicator displays Weigh Ou

t Complete and goes back to Step 1

Inbound Trucks

1. Press the Inbound Trucks touch widget. The system prompts for a password if one has previously been set for Inbound Trucks. Enter the password.

2. Up to eight inbound weighments will display with ID, weight and time/date. The touch widget will switch to

Page Down, Delete, Delete ALL and Exit. The top weighment is selected.

3. Press the

Up or Down Arrows to change the selection , or use the Page Up or Page Down touch widget to scroll through

stored inbound weighments (eight at a time).

4. Press the delete, press the

5. Press the press the

Parameter Default Button Description

System Password

Inbound Trucks Password

Stored Tares

Value Swapping

Delete touch widget to delete the selected inbound weighment. The system will prompt Are You Sure. To

Yes touch widget; to cancel, press the No softkey.

Delete All touch widget to delete all inbound weighments. The system will prompt Are You Sure. To delete,

Yes touch widget; to cancel, press the No touch widget.

“ ”

Setup Password

Trucks Password

Stored Tares

Value Swapping

Table 1-11. Truck In/Out Application Setup and Configuration

Change the password that is required for entry into the Setup Menu. Setting the password to nothing will cause the system to not prompt for a password when the Setup Menu touch widget is pressed

Change the password that is required for entry into the Inbound Trucks display. Setting the password to nothing will cause the system to not prompt for a password when the Inbound Trucks touch widget is pressed

When ON, the inbound weight is stored even after weighing out. When OFF, the inbound record is deleted after weighing out.

When ON, the gross weight is always the larger of the gross and tare values, whether the outbound weight was larger or smaller than the inbound weight. When OFF, gross is always the outbound weight.

Page Up,

18 Visit our website www.RiceLake.com

Page 25

Parameter Default Button Description

Threshold Weight

Import/Export Data Import/Export

Add/Edit Products - Add//Edit Product Add/Edit products in the Product database table. Delete Products - Delete Product Delete products in the Product database table. Add/Edit Customers - Add//Edit Customer Add/Edit customers to the Customer database table. Delete Customers - Delete Customer Delete customers in the Customer database table.

Print Report

Truck Exit

5000 lb

Required/

Disabled

Threshold Weight

- Customer by Product Customer by Truck

Truck Exit

Table 1-11. Truck In/Out Application Setup and Configuration (Continued)

Weight that triggers the optional traffic light and is the weight that the scale must go above or below before weighments are allowed.

1280 standard function. Allows the operator to import Products into the Product database table from a USB flash drive using .DB file type; also allows the user to save transactions to the USB flash drive. Reference the 1280 Technical Manual import/Export section for more details.

Print two totals reports (totals only). Allows operator to decide if truck needs to go below the threshold in between

weighments.

Introduction

Page 26

1280 Series Color Touchscreen Indicator

WARNING

Mark and drill holes

Use hardware to mount

Place washers on indicator side studs

Secure with washers and knobs

Note

2.0 Installation

This section describes procedures for connecting power, load cells, digital I/O and data communications cables to the 1280 indicator. Instructions for replacement of the circuit boards are also included, along with assembly drawings and replacement parts lists for the service technician.

• Use a wrist strap to ground yourself and protect components indicator enclosure.

• Procedures requiring work inside the indicator must be performed by qualified service personnel only.

• In the 1280 wall and universal mounts, the supply cord serves as the power disconnect. The power receptacle to the indicator must be easily accessible for these models.

2.1 Unpacking

Immediately after unpacking, visually inspect the 1280 to ensure all components are included and undamaged. The shipping carton should contain the controller, display, CD, parts kit, any options o rdered with the unit and the appropriate manuals. If any parts were damaged in shipment, notify Rice Lake Weighing Sys te m s and the shipper immediately.

2.2 Mounting/Assembly

There are three 1280 enclosure styles: a universal mount, wall mount and panel mount.

rom electrostatic discharge (ESD) when working inside the

2.2.1 Universal Mount Enclosure with Tilt Stand

The universal mount is shipped with a tilt stand and can be mounted on a wall, tabletop or any flat surface.

Figure 2-1. Mounting the 1280 – Universal Enclosure

1. Using the tilt stand as a template, mark the screw locations. See Figure 2-5 on page 22 for dimensions.

The 1280 universal enclosure can mount to the same location where a 920i universal enclosure was mounted; the screw locations for the tilt stand are the same.

2. Drill holes for the screws.

3. Mount the tilt stand using the appropriate hardware (not included).

4. Place one washer on each side stud of the indicator enclosure.

20 Visit our website www.RiceLake.com

Page 27

5. Place the indicator side studs into the holes on the arms of the tilt stand.

Shipping Bracket

Open Door

Note

Loosen Four Screws

Open Door

Figure 2-3. Open Cover – Universal

Note

6. Secure with remaining washers and hand knobs from the hardware kit.

7. Wire the indicator according to Section 2.4 on page 33.

Remove Shipping Bracket

The universal mount is shipped with a shipping bracket inside the enclosure to stabilize it during shipping.

1. Loosen the four screws securing the front door.

Pull the door and fully extend the hinge to swing the door open. See Figure 2-2.

3. The bracket will be loose, remove it from the enclosure.

Installation

Figure 2-2. Remove Shipping Bracket

Retain shipping bracket for future shipping needs.

Controller Disassembly

The controller can be tilted up with the locking tab or it can be completely removed from the enclosure by removing the retaining wire clip.

1. Remove the large fillister screw in the back of the indicator to tilt or

remove the controller. The seal must be broken for this purpose.

2. Loosen the four screws securing the front door.

3. Pull the door and fully extend the hinge to swing the door open.

4. Pull the locking tab to the left to release the controller assembly.

5. Remove the wires connected to the controller assembly.

6. Remove the retaining wire clip connected to the controller assembly.

This only needs to be removed if the controller is being removed from the enclosure.

7. Lift controller assembly from the enclosure.

Reverse this procedure for reassembly. Upon reassembly, ensure

To close the door to the universal enclosure, push the bail in and down so that it does not get caught on the controller assembly.

display and keyboard wires a

re properly connected.

Page 28

1280 Series Color Touchscreen Indicator

Locking Tab

Controller Assembly

Retaining Wire Clip

Bail

BASE AND HOLE PATTERN

IS SYMMETRICAL ABOUT

9.24

6.00

5.25

4.25

1.50

10.86

Dimensions are in inches

IMPORTANT

Figure 2-4. Remove CPU Assembly– Universal

Sealing the Setup Switch

In certain Legal for Trade applications, it may be necessary to seal the indicator to restrict access from the setup switch. Use the following instructions to seal the universal enclosure.

1. Turn off (right position) the audit trail jumper (JP1). See Section 2.7 on page 39 for instructions on how to remove the

2. If not previously installed, install the large fillister screw in the back of the indicator.

3. Wrap the lead wire seal through the large fillister screw and the two smaller fillister screws in order to seal the

22 Visit our website www.RiceLake.com

Figure 2-5. Universal Surface Mount Stand Dimensions

This illustration is not to scale. It is for illustration purposes only. Use the dimensions to mark the holes for the universal mount, or use the bottom of the tilt stand as a template. Do not use Figure 2-5 as a template.

The audit trail jumper (JP1) needs to be disabled, in the off (right) position, in order to seal the setup switch with a lead seal wire. Access is not prevented simply by sealing the setup switch.

CPU board (which is necessary to disable the audit trail jumper). This will restrict access from the configuration menu through the front panel.

indicator. This will restrict access to the setup switch.

Page 29

Installation

Small Fillister Screws

Large Fillister Screw

Small Fillister Screws

Large Screw

Figure 2-6. Seal the Setup Switch (Universal Mount)

Sealing the Front Door

In certain Legal for Trade applications, it may be necessary to seal the indicator to restrict access from the internal hardware of the indicator. To seal the universal enclosure front door, wrap the le ad wire seal through the large bottom right screw securing the front door and the two small fillister screws on the bottom of th e enclosure. Alternatively, the A/ D scale card includ es fillister screws and a bracket that prevent the load cell cable from being di sconnected.

Figure 2-7. Seal the Front Door (Universal Mount)

Page 30

1280 Series Color Touchscreen Indicator

Note

Figure 2-8. 1280 Wall Mount

Screws

Shipping Bracket

Loosen four screws

Open Door

Figure 2-10. Open Door – Wall Mount

When closing the door, tighten screws to 15 in-lb to ensure the enclosure is securely sealed.

Note

2.2.2 Wall Mount Enclosure

1. Using the wall mount as a template, mark the screw locations. See Figure 2-14 on page 26 for dimensions.

The 1280 wall enclosure can mount to the same location where a 920i was mounted; the screw locations are the same.

2.Drill the holes for the screws.

3. Mou

nt the wall mount using the appropriate hardware (not included).

Remove Shipping Bracket

1. Loosen the four screws on the front door. See Figure 2-10.

2. Swing the door open.

3. Remove the four screws securing the bracket in place.

4. Remove bracket from the enclosure.

Figure 2-9. Remove Shipping Bracket – Wall Mount

Controller Disassembly

1. Loosen the four screws on the front door.

2. Swing the door open.

3. Remove the wires connected to the controller assembly.

4. While supporting the controller assembly, use a screwdrive r

to slide the mounting plate down. See Figure 2-11.

5. Lift the controller assembly up to remove it from the DIN rail

and pull it out of the enclosure.

Reverse this procedure for controller assembly installation.

24 Visit our website www.RiceLake.com

Page 31

Installation

Slide Mounting Plate Down

Controller Assembly

IMPORTANT

Enclosure hidden for illustration purposes only. Controller Assembly does not need to be removed from the enclosure to seal the setup switch.

Large Fillister Screw

DIN Rail Clip

Figure 2-11. Remove Controller Assembly - Wall Mount

Sealing the Setup Switch

In certain Legal for Trade applications, it may be necessary to seal the indicator to restrict access from the setup switch. Use the following instructions to seal the wall mount enclosure.

The audit trail jumper (JP1) needs to be disabled, in the off (right) position, in order to seal the setup switch with a lead seal wire. Access is not prevented simply by sealing the setup switch.

1. Turn off (right position) the audit trail jumper (JP1). See Section 2.7 on page 39 for instructions on how to remove the

CPU board (which is necessary to disable the audit trail jumper). This will restrict access from the configuration menu through the front panel.

2. Wrap the lead wire seal through the large fillister screw and the bottom tab of the DIN rail clip to restrict access to the

setup switch.

Figure 2-12. Seal the Setup Switch (Wall Mount)

Page 32

1280 Series Color Touchscreen Indicator

Large Screw

Hole in Door Enclosure

11.00"

18.84"

19.64"

13.00"

14.20"

Ø 0.33"

18.22"

VERTICAL

DIRECTION

IMPORTANT

Sealing the Front Door

In certain Legal for Trade applications, it may be necessary to seal the indicator to restrict access from the internal hardware of the indicator. To seal the wall mount enclosure front door, wrap the lead wire seal through the large screw securing the front door and the hole in the edge of the door enclosure. Alternatively, the A/D scale card includes fillister screws and a bracket that prevent the load cell cable from being disconnected.

Figure 2-13. Seal the Front Door (Wall Mount)

Figure 2-14. Wall Mount Dimensions

This illustration is not to scale. It is for illustration purposes only. Use the dimensions to mark the holes for the wall mount. Do not use Figure 2-14 as a template.

26 Visit our website www.RiceLake.com

Page 33

2.2.3 Panel Mount Enclosure

Figure 2-15. Mark and Drill Holes for Panel

Tape to outside of panel

Display Assembly

DIN Rail Bracket

The 1280 panel mount will ship partially assembled. The display assembly must be removed from the backing plate to allow installation on the existing panel.

1. Tape the panel mount template to the outside of the panel.

See Figure 2-15 and Figure 2-17.

2. Mark and drill holes according to the template.

3. Place the display assembly and the DIN rail bracket on either

side of the panel. Ensure that the DIN rail bracket is horizontal, as shown in Figure 2-16.

4. Use studs, nuts and washers to secure the display assembly to the DIN rail bracket.

Installation

Figure 2-16. Mounting the 1280 – Panel Enclosure

Page 34

1280 Series Color Touchscreen Indicator

161039-TEMPLATE

9.000

FOOT PRINT

OF PANEL

AND BRACKET

9.000

FOOT PRINT

OF PANEL

AND BRACKET

7.440 HOLE

PATTERN

7.440 HOLE

PATTERN

.250

DRILL

1.00

HOLE

4.75

.25

CUT OUT ALONG FOOT PRINT LINES AND TAPE ONTO PANEL TO BE DRILLED TO ASSIST IN LAYOUT OF HOLES

RICE LAKE WEIGHING SYSTEMS

1280 PANEL MOUNT INDICATOR

MOUNTING TEMPLATE

Dimensions are in inches

1.00

Dimensions are in inches

Panel Mount Dimensions

Touch Only 7 Inch Panel Mount Dimensions

Figure 2-17. Panel Mount with Keypad Dimensions

Figure 2-18. 7 Inch Touch Only Panel Mount Dimensions

28 Visit our website www.RiceLake.com

Page 35

Touch Only 12 Inch Panel Mount Dimensions

10.00

1.00

FOOT PRINT OF DISPLAY PANEL ON OUTSIDE OF PANEL

8.44

.78

14.00

12.44

4X .219

Dimensions are in inches

IMPORTANT

Installation

Figure 2-19. 12 Inch Touch Only Panel Mount Dimensions

These illustrations are not to scale. It is for illustration purposes only. Use the dimensions to mark the holes for the panel mount, or use the template provided with the indicator. Do NOT use Figure 2-17, Figure 2-18 and

Figure 2-19 as a template.

Page 36

1280 Series Color Touchscreen Indicator

Note

Hook the bracket of the controller assembly onto the DIN rail.

Installing Grounding Bus Bar

The grounding bus bar is installed on the controller assembly for grou nding purposes on the 1280 panel mount enclosure.

1. Remove the four corner screws from the controller assembly.

Secure grounding bus bar onto controller assembly using screws from step 1.

Figure 2-20. Grounding Bus Bar Installation

Installing the Controller Assembly

The controller assembly can be mounted to a standard DIN rail.

1. Hook the bracket on the back of the controller assembly onto the DIN rail.

The controller assembly can be installed up to 30 inches from the display of the panel mount enclosure.

Figure 2-21. Hook Bracket on DIN Rail

2. Push controller assembly against the DIN rail in order to engage the spring clip. The controller assembly will lock onto

the DIN rail bracket.

3. Connect wiring. See

Section 2.4 on page 33.

Removing Controller Assembly

1. Disconnect wiring.

2. While supporting the controller assembly, use a screwdriver to slide the mounting plate down.

3. Unhook the controller assembly from the DIN rail bracket.

4. Carefully remove the controller assembly from the DIN rail bracket and release the mounting plate.

30 Visit our website www.RiceLake.com

Page 37

Installation

IMPORTANT

Enclosure and grounding bus bar hidden for illustration purposes only. Controller Assembly does not need to be removed from the enclosure to seal the setup switch. Similarly, the grounding bus bar may remain attached if previously installed.

Large Fillister Screw

DIN Rail Clip

Figure 2-22. Remove Controller Assembly from DIN rail

Sealing the Setup Switch

In certain Legal for Trade applications, it may be necessary to seal the indicator to restrict access from the setup switch. Use the following instructions to seal the panel mount enclosure.

The audit trail jumper (JP1) needs to be disabled, in the off (right) position, in order to seal the setup switch with a lead seal wire. Access is not prevented simply by sealing the setup switch.

Wrap the lead wire seal through the large fillister screw and through the bottom tab of the DIN rail clip to restrict access to the setup switch. Alternatively, the A/D scale card includes fillister screws and a bracket that prevent the load cell cable from being disconnected.

Figure 2-23. Seal the Setup Switch (Panel Mount Enclosure)

Page 38

1280 Series Color Touchscreen Indicator

See Figure 2-25 on page 32 for label location.

WARNING

Note

Option Card

Slot Cover Plate

Controller Label Slot 1 on this side.

2.3 Option Card Installation

Use the following instructions to install option cards in the 1280. There are two SPI communication buses for the six option card slots: one for slots 1, 2 and 3 and a second for slots 4, 5 and 6. Communication is faster with less traffic on an SPI bus. For optimal performance, populate slots 1 and 4 first in order to keep card s on their own SPI bus.

Figure 2-24. Label on the Top of the Controller Assembly

• Option cards are not hot-swappable. Disconnect power to the 1280 before installing option cards.

• Use a wrist strap to ground yourself and protect components from electrostatic discharge (ESD) when working inside the indicator enclosure.

• Procedures requiring work inside the indicator must be performed by qualified service personnel only.

•In the

1280 wall and universal enclosures, the supply cord serves as the power disconnect. The power receptacle to the

indicator must be easily accessible for these models.

It may be easier to install option cards in the universal enclosure if the controller assembly is removed from the enclosure. See Section 2.2.1 on page 20.

1.Remove the hardware securing the slot cover plate.

2. Remove the slot cover plate.

3. Slide the option card into place.

4. Secure the card using the hardware that secured the slot cover plate.

5. Attach cables. See

Section 2.4 on page 33.

Figure 2-25. Option Card Installation

32 Visit our website www.RiceLake.com

Page 39

Figure 2-26. Installed Option Card

Installed Option Card

Figure 2-27.

Option Card Seal

Grounding Washer

Ensure contact between the exposed shielding and the tabs of the grounding washer.

Seal the Scale Card

Once an option card has been put into place and cable connections have been made, a seal can be placed over the card and connections to restrict access and keep them from being removed.

1. Align the sealing bracket over the connectors on the option card.

2. Secure

3. Insert the lead wire seal through the holes in the sealing bracket and the large fillister screws as shown in

with two large fillister screws.

Figure 2-27.

Installation

2.4 Cable Connections

The 1280 universal and wall enclosures provide cord grips for cabling into the indicator; one is for the power cord and the rest are to accommodate interfac e cables. Install plugs in a ll unused cord grips to prevent moisture from entering the enclosure. Secure wires after cabling is complete to avoid low voltage circuits contacting high voltage circuits.

2.4.1 Grounding Through Cord Grips

To ground cables to the universal or wall enclosures, route the cable through one of the metal cord grips. Ensure the exposed shielding makes contact with the tabs of the grounding washer inside the cord grip. See Figure 2-28.

Figure 2-28. Universal and Wall Enclosure Grounding

Page 40

1280 Series Color Touchscreen Indicator

Foil Insulated Wire

Silver

side out

Shield wire (cut)

Cut insulation here for foil sheilded cables

Length of foil before folding back on cable insulation

Grounding Clip

Place the shield wire on the grounding clip on the Controller Assembly.

Note

Light pipes and mounting plate removed for clarity.

LED5

JP2

JP1

LED8

FW1

Vx.xx

LED4

LED1

LED2

LED3

JP4

JP3

Micro

USB-AB

Exc1-

Exc1+

Sen-

Sen+

Sig-

Sig+

Exc1-

Exc1+

Sen-

Sen+

Sig-

Sig+

2.4.2 Panel Enclosure Grounding

To ground cables to the panel enclosure, place the shield wire on the grounding clip on the controller assembly.

Figure 2-29. 1280 Panel Enclosure Grounding

The controller assembly must be grounded to the stud and nut that hold the panel enclosure to the backing plate per national electrical code (NEC).

2.4.3 Load Cells

Use the following instructions to attach the cable from a load cell or junction box to an installed A/D scale card channel.

1. Route the cables.

2. Remove connector J1 from the parts kit a

3. Plug the connector into the appropriate channel of the A/D scale card (see Figure 2-30).

4. Wire the load cell cable from the load cell or junction box to connector J1 and/or J2 if using a dual A/D scale card as

34 Visit our website www.RiceLake.com

nd wire the load cell cables to it.

shown in Table 2-1 on page 35.

Channel 2

Channel 1

• If using a 6-wire load cell cable (with sense wires), remove jumpers JP1 and JP2 before reinstalling connector J1. On

dual-channel A/D scale cards, remove jumpers JP3 and JP4 for connections to J2.

• For 4-wire installation, leave jumpers JP1 and JP2 on (or JP3 and JP4 depending on the channel).

Figure 2-30. Single and Dual A/D Scale Cards

Page 41

Installation

IMPORTANT

Note

J17

J10

J11

JP1

J13

U13

JP3

ASSY

PN/Rev

RICE LAKE

CGND1

CGND2

BAT1

LVDS DISPLAY

DIO

ETHERNET

ANTENNA

PCIe

iMX6

KEYBOARD

POWER

CGND

MFGR

PORT#2

PORT#1

SERIAL

MFGR PN# VER. x.xxx

PCIe

WiFi-Blu

RX/B

GND

AUDIT TRAIL

OFF

uUSB-AB

DUAL

USB-A

Micro

SD Card

COM

DIO8

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

GND

PWR

RTS/Y

TX/A

-6V

CTS/Z

RTS/Y

TX/A

GND

+6V

RX/B

CTS/Z

CGND

JTAG

RESET

WD_RST

SIDE UP

INSERT

Light pipes and mounting plate removed for clarity.

Scale Card

Connector Pin

1 2 3 4 5 6

Function

+SIG

–SIG +SENSE –SENSE

+EXC –EXC

Table 2-1. Scale Card Pin Assignments

The A/D scale card must be removed from the controller prior to configuring the sense line jumpers.

The hardware of J2 will not be populated on a single A/D scale card.

2.4.4 Serial Communications

The two communication ports on the 1280 CPU board support full duplex RS-232, RS-422 or RS-485 communications at up to 115200 bps.

Figure 2-31. CPU Board (Top View)

Use the following instructions to attach serial communication cable s.

1. Route the cable through the cord grip and ground the shield wire. See Section 2.4 on page 33.

2. Remove the screw holding the face plate.

3. Use clip to ground the front plate.

4. Wire the cables to the connector (included in the parts kit).

5. Plug the connector into J6 and J7 on the board.

Page 42

1280 Series Color Touchscreen Indicator

Note

Table 2-2 shows the pin assignments for communication ports.

Connector Pin Signal Port

1GND1 2 RS-232 RX/RS-485 B 3 RS-232 TX/RS-485 A 4 RS-232 CTS/RS-485 Z 5 RS-232 RTS/RS-485 Y 1GND2 2 RS-232 RX/RS-485 B 3 RS-232 TX/RS-485 A 4 RS-232 CTS/RS-485 Z 5 RS-232 RTS/RS-485 Y

Table 2-2. Serial Port Pin Assignments

Serial ports are configured using the Serial menu

. See Section 5.1 on page 71 for configuration information.

An optional dual-channel serial communications card, Kit PN 164685, is also available. Each serial option card provides two addi

tional serial ports. Both ports on the option card can support RS-232, RS-422 or RS-485.

All wiring must conform to the NEC or local ordinances.

2.4.5 CPU Digital I/O Wiring

Digital I/O pins are configured using the Digital I/O menu. See Section 8.0 on page 97 for configuration information. An optional 24 I/O bit card (PN 164684) is also available. Each Digital I/O option card provides an additional 24 configurable I/O

ts. Alternatively, a 4 channel Relay card (PN 164689) is also available.

Use the following instructions to wire to

1. Route the cables through the cord grip and ground the shield wire. See Section enclosure, route wires to a Relay Rack if so equipped (skip steps 2 and 3).

2. Remove the screw holding the face plate.

3. Use clip to ground the front plate.

4. Wire the cables to the connector (included in the parts kit).

5. Plug the connector into J1 on the board.

Table 2-3 shows the pin assignments for the Digital I/O connector

the CPU board DIO connector.

Connector Pin Signal

Table 2-3. CPU Digital I/O Pin Assignments

1+5 VDC 2GND 3 DIO 1 4 DIO 2 5 DIO 3 6 DIO 4 7 DIO 5 8 DIO 6 9 DIO 7

10 DIO 8

2.4 on page 33. For a wall mount

36 Visit our website www.RiceLake.com

Page 43

2.5 Wiring Schematics

To Wall Outlet

Overlay

Keypad

To Fan

ASSY

PN/Rev

MH1

R265

MH4

C11

C18

R266

B17

A17

B18

A18

R16

R14

B17

A17

B18

A18

MH3

C13 C12

C10

R12

C15

C16

R21

C20

C23

B17

A17

B18

A18

B17

A17

B18

A18

B17

A17

B18

A18

C14

L10

TH3

B17

A17

B18

A18

B17

A17

B18

A18

B17

A17

B18

A18

C289

RICE LAKE

R37

R29

R34

R24

R28

R35

R36

R23

R26

C22

C17

R22

C21

TH2

C296C290

R39

R30

R32

R38

R40

R31

R33

R25

R27

MH5

MH2

R11

R10

R13

R17

C19

R18

TH1

R20

R19

R15

R41

AUX

J17

J10

J11

JP1

J13

U13

JP3

ASSY

PN/Rev

RICE LAKE

CGND1

CGND2

BAT1

LVDS DISPLAY

DIO

ETHERNET

ANTENNA

PCIe

iMX6

KEYBOARD

POWER

CGND

MFGR

PORT#2

PORT#1

SERIAL

MFGR PN# VER. x.xxx

PCIe

WiFi-Blu

RX/B

GND

AUDIT TRAIL

OFF

uUSB-AB

DUAL

USB-A

Micro

SD Card

COM

DIO8

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

GND

PWR

RTS/Y

TX/A

-6V

CTS/Z

RTS/Y

TX/A

GND

+6V

RX/B

CTS/Z

CGND

JTAG

RESET

WD_RST

SIDE UP

INSERT

Touch Screen

Back Plane

HMI Board

Display

Power Supply

CPU Board

1280 Keyed Version

Installation

Figure 2-32. Wiring Diagram

Page 44

1280 Series Color Touchscreen Indicator

J17

J10

J11

JP1

J13

U13

JP3

ASSY

PN/Rev

RICE LAKE

CGND1

CGND2

BAT1

LVDS DISPLAY

DIO

ETHERNET

ANTENNA

PCIe

iMX6

KEYBOARD

POWER

CGND

MFGR

PORT#2

PORT#1

SERIAL

MFGR PN# VER. x.xxx

PCIe

WiFi-Blu

RX/B

GND

AUDIT TRAIL

OFF

uUSB-AB

DUAL USB-A

Micro

SD Card

COM

DIO8

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

GND

PWR

RTS/Y

TX/A

-6V

CTS/Z

RTS/Y

TX/A

GND

+6V

RX/B

CTS/Z

CGND

JTAG

RESET1WD_RST

SIDE UP

INSERT

J19

(not shown)

J18

(not shown)

To 7 inch

Display (from J9)

To 12 inch

Display

(from J9 & J18)

Touch Screen Overlay Card

CPU Board

Refer to Figure 2-32 for remaining wiring schematic

HMI touch cable (PN 180002) plugs from J2 on the overlay card to J19 (not shown) on backside of CPU board.

Connect CPU to display cable (PN 164995 or 164970) from J9 to 7 inch Display.

Connect CPU to display cable (PN

180001) from J9 and J18 (not shown) back of CPU board to 12 inch Display.

Note: Additional cable lengths are available.

Note

1280 Touch Only Version (Virtual Keypad)

2.6 Configuration Methods

The 1280 indicator can be configured using:

• Front panel keys to navigate through a series of configuration menus (see Section 3.0 on page 53)

• Revolution

• EDP command configuration (see Section 15.0 on page 147)

38 Visit our website www.RiceLake.com

configuration utility (see Section 13.0 on page 119)

Some configuration parameters, such as those used to configure the 1280 display and widgets, cannot be accessed through the configuration menus.

1280. See Section 14.0 on page 135.

the

Figure 2-33. 7 and 12 Inch Panel Mounts - Touch Only

MSI-8000HD provides the most complete and efficient configuration interface for

Page 45

Installation

WARNING

IMPORTANT

Controller Assembly

CPU Board

Face Plate

IMPORTANT

Figure 2-35. Remove CPU Board from the Face Plate

2.7 CPU Board Replacement

• Use a wrist strap for grounding to protect components from electrostatic discharge (ESD) when working inside the indicator enclosure.

• Procedures requiring work inside the indicator must be performed by qualified service personnel only.

•In the

1280 wall and universal enclosures, the supply cord serves as the power disconnect. The power receptacle to the indicator must be

easily accessible for these models.

1. Disconnect all cables from the controller assembly.

2. Remove the two screws securing the face plate to the controller assembly.

3. Remove the face plate from the controller assembly. The CPU board will remain attached to the face plate.

Handle with care. The boards are fragile.

Only remove the CPU board from the face plate if it is being replaced.

4. Remove the nut for the antenna and the two screws securing

the CPU board to the face plate.

5. Remove the CPU board.

Reverse procedure for reassembly.

Figure 2-34. Remove CPU Board

Page 46

1280 Series Color Touchscreen Indicator

WARNING

IMPORTANT

Note

Mounting Bracket removed for illustration purposes only.

Fan Plate

Connector

Power Supply

Fan Plate

Back Plane

Image shown in reverse order from Figure 2-36 for illustration purposes.

2.8 Power Supply Replacement

• Use a wrist strap for grounding to protect components from electrostatic discharge (ESD) when working inside the indicator enclosure.

• Procedures requiring work inside the indicator must be performed by qualified service personnel only.

•In the

Use the following instructions to replace the power supply.

1280 wall and universal enclosures, the supply cord serves as the power disconnect. The power receptacle to the indicator must be

easily accessible for these models.

1. Disconnect all cables from the controller assembly.

2. Re

move the four screws from the fan plate.

3. Carefully remove the fan plate/back plane assembly from the enclosure. Be sure to support the power supply as it is removed from the enclosure; it is only connected to the fan plate/back plane assembly by a connector.

Handle with care. The boards are fragile.

The mounting bracket has been removed for illustration purposes only. It does not need to be removed for disassembly.

4. Disconnect the power supply from the connector.

Reverse procedure for reassembly.

40 Visit our website www.RiceLake.com

Figure 2-36. Remove the Fan Plane

Figure 2-37. Disconnect the Power Supply

Page 47

Installation

WARNING

IMPORTANT

Back Plane

Fan Plate

Note

2.9 Replace Fan Plate and Back Plane

• Use a wrist strap for grounding to protect components from electrostatic discharge (ESD) when working inside the indicator enclosure.

• Procedures requiring work inside the indicator must be performed by qualified service personnel only.

•In the

Use the following instructions to replace the fan plate and back plane.

1280 wall and universal enclosures, the supply cord serves as the power disconnect. The power receptacle to the

indicator must be easily accessible for these models.

If replacing CPU boards in the 1280, a new fan plate is also required.

1. Disconnect the power supply. See Section 2.8 on page 40.

Remove the five screws securing the back plane to the fan plate.

3. Remove the back plane.

Figure 2-38. Remove Backplate from Controller Assembly

Ensure to note the orientation of the fan prior to removal. It is important that the fan is reinstalled in the correct orientation.

4. Remove the four screws securing the fan to the fan plate.

Figure 2-39. Remove Four Screws and Fan from Fan Plate

5. Remove the fan.

Page 48

1280 Series Color Touchscreen Indicator

15 13 12

Inside Bottom of Enclosure

(some items are hidden for clairity)

51 50

Reverse this procedure for reassembly.

2.10 Replacement Parts

Figure 2-40. Replacement Parts Drawing - Universal Enclosure

42 Visit our website www.RiceLake.com

Page 49

Item No. Part No. Description

169926 Door Assembly, Universal (inc. 1-11) 1 165970 Screw, 1/4-20NC x 3/4'' 2 161731 Overlay, Keypad 1280 3 161730 Overlay, Touchscreen 1280 4 166631 Screw, 1/4-20NC x 3/4''

182281 Washer, Washer Cup 1/4"

182246 Washer Gasket, 1/4" 6 169450 Front Door, 1280 Universal 7 166653 Retainer, Pushnut Bolt 1/4'' 8 69898 Washer, Nylon #4 ID = 0.112 9 160759 Board Assembly, 1280 HMI_Int 10 159280 Nut, Lock Nylon Insert 11 172840 Decal, 1280 Start Screen

160383 Universal Display, 500 NITS (inc. 12-15)

160385 Universal Display, 1000 NITS (inc. 12-15) 12 58248 Nut, Lock 6-32 NC HEX Nylon

162272 Mounting Bracket Display (500 Nit)

162271 Mounting Bracket Display (1000 Nit) 14

163467 Cable, CPU to Display (500 Nit)

163444 Cable, CPU to Display (1000 Nit) 15

163400 Display, (500 NITS) 7'' LCD

163399 Display, (1000 NITS) 7'' LCD

169461 Universal Controller Bracket (inc. 16-20) 16 53075 Clamp, Ground Cable Shield 17 168545 Bail, 1280 Controller Retainer Wire 18 14839 Screw, Machine 6-32NC x 1/4'' 19 169462 Bracket Assembly, 1280 Controller 20 168937 Snap Tap, 1280 Controller Support

169927 Universal Cabinet Assembly (inc. 21-39) 21 40672 Wire Assembly, Ground 9'' 22 169410 Hinge Link 23 160379 Gasket, Front Panel 24 124698 Panel Plug, Round Solid 25 167537 Washer, Sealing BarTite #6 26 183663 Tall Flanged Drilled Hex Head Screw 27 169452 Enclosure Shell Assembly, Universal 28 169875 Cord Grip, PG 9 With Nut 29 169876 Cord Grip, PG 13.5 With Nut

30 15626 Cord Grip, Black PG 9 31 15627 Locknut, Black PCN9 32 30375 Seal Ring, Nylon PG9 33 164598 Vent, Breather Sealed 34 88734 Nut, Breather Vent 35 58248 Nut, Lock 6-32 NC Hex Nylon 36 166240 Cable, Antenna Extension 37 168098 Antenna, RP-SMA

182281 Washer, Washer Cup 1/4" 182246 Washer Gasket, 1/4"

39 16892 Label, Ground

Other Items (inc. 40-49) 40 67550 Clamp, Ground Cable Shield 41 166693 Cable, CPU to HMI 1280 42 14626 Nut, Kep 8-32 NC Hex 43 167700 Wire, Ground 9 Inch 44 15134 Washer, Lock NO 8 Type A

182282 Washer Cup #10

182247 Washer Gasket #10 46 183662 Tall Flanged Drilled Hex Head Screw 47 161620 Stand, Tilt Surface Mount

163785 Universal Parts Kit (inc. 50-56) 50 164064 Hand Knob, 4-Arm 5/16-18 51 79024 Washer, Plain 5/16'' Nylon 52 42149 Bumper, Rubber Grommet 53 169879 Grounding Clip, Cord Grip PG 13.5 Cable 54 169878 Grounding Clip, Cord Grip PG 9 Cable 55 19538 Post Plug, Slotted Black

172859 Bracket Assembly (inc. 57-59) 57 172856 Bracket, 1280 Controller 58 15149 Foot, Rubber Bumper 59 172872 Pad, Foam

165108 Cord, US Power

165109 Cord, European Power 62 169676

Controller Assembly (see Figure 2-43 on

page 48)

Item No. Part No. Description

Table 2-4. Universal Parts List

Installation

Page 50

1280 Series Color Touchscreen Indicator

17 18

29 21

Figure 2-41. Replacement Parts Drawing - Panel Enclosure

44 Visit our website www.RiceLake.com

Page 51

Installation

Item

No.

Part No. Description

169930

1280 Panel Enclosure Face Plate

Assembly (Inc 1-7) 1 169929 Face Panel 1280 2 160379 Gasket, Front Panel 3 164120 Overlay, Touchscreen 4 164121 Overlay, Keypad 5 172840 Decal, 1280 Start Screen 6 160759 Board Assembly, HMI-Int 7 69898 Washer, Nylon #4 ID = 0.112 8 159280 Nut, Lock Nylon Insert

166725 500 NIT Display (Inc 9-12) 166726 1000 NIT Display (Inc 9-12)

162272 Mounting Bracket Display (500 Nit) 162271 Mounting Bracket Display (1000 Nit)

163400 Display, (500 Nit) 7'' LCD 163399 Display, (1000 Nit) 7'' LCD

11 58248 Nut, Lock 6-32NC Hex Nylon 12

164995 Cable, CPU to Display (500 Nit)

164970 Cable, CPU to Display (1000 Nit) 13 162309 Backer Bracket 14 166838 Bracket Assembly, DIN Rail

163786 Parts Kit, Panel (Inc. 16-25 and all NS) 16 168872 Wire, 9'' Ground, 1/4'' Eye 17 169023 Ground Bus Bar 18 53075 Clamp, Ground Cable Shield 19 166241 Cable, Antenna Extension 20 168098 Antenna, RP-SMA 21 14877 Screw, Fillister 10-32NF x 3/8'' 22 168629 Ground Strap, 1280 CPU 23 14630 Nut, Lock 10-32NF Hex 24 22062 Washer, Plain No 10 Type A 25 168877 Screw, Set #10-32 x 1'' 26 14621 Nut, Kep 6-32NX Hex NS 15130 Washer, Lock No 6 Type A NS 158207 Screw, Mach 6-32 x 1/4'' Fillister 27 166694 Cable, CPU to HMI 1280 28 169676 Controller Assembly 29 67550 Clamp, Ground Cable Shield NS 14839 Screw, Mach 6-32NC x 1/4''

Item

No.

Part No. Description

Note

If controller is not connected to the panel, ground per NEC.

Table 2-5. Replacement Parts – Panel Enclosure

Page 52

1280 Series Color Touchscreen Indicator

13940

1735 34 42 632 31 1211

15 16

14 16

4645

24 25 261927

910

Cover exploded for clarity

Inside Bottom of Enclosure

(some

items hidden for clarity)

Figure 2-42. Replacement Parts Drawing - Wall Enclosure

46 Visit our website www.RiceLake.com

Page 53

Item

No.

Part No. Description

164680

1280 Indicator Sub-Assembly (includes

1-29) 1 161416 Enclosure Assembly 2 172840 Decal, 1280 Start Screen 3 164120 Overlay, Touchscreen 4 164121 Overlay, Keypad 5 160759 Board Assembly, 1280 HMI Interface 6 159280 Nut, Lock Nylon Insert 7 69898 Washer, Nylon #4 ID 0.112'' 8 14626 Nut, Kep 8-32NC Hex 9 15134 Washer, Lock No 8 Type A 10 40672 Wire Assembly, Ground 9'' 11 43383 Rail, DIN 12.75'' Length 12 164900 Back Plane Panel, 1280 13 68724 Gasket, Cover 14 71447 Screw, Mach 1/4 - 28NF x 3/4'' 15 71455 Screw, Mach 1/4 - 28NF x 3/4'' 16 71739 Clip, Clinching Enclosure 17 14875 Screw, MACH 10-32NF x 3/8'' 18 80590 Mount, Cable tie Arrowhead 19 166241 Cable, Antenna Extension 20 166634 Washer, Sealing Bartite 21 168098 Antenna, RP-SMA 22 88733 Vent, Breather Sealed 23 88734 Nut, Breather Vent 24 124695 Panel Plug, Round Solid 25 169876 Cord Grip, PG13.5 With Nut 26 68600 Cord Grip, PG11 27 68599 Seal Ring, Nylon PG 11 28 68601 Nut, PG 11, Power Cord Cable

29 16892 Label, Ground Protective 31 166838 Bracket Assembly, DIN Rail 32 168629 Ground Strap 33 67550 Clamp, Ground Cable Shield 34 167701 Wire, Ground 24 #8 Eye

173052 Bracket Assembly, 1280 (Includes 35-36) 35 172860 Bracket, 1280 Wallmount 36 173053 Gasket, 1280 Wallmount 37 166694 Cable, CPU to HMI

166725

Universal Display, 500 NITS (Includes 38-

41)

166726

Universal Display, 1000 NITS (Includes 38-41)

164995 Cable, CPU to Display (500 Nit)

164970 Cable, CPU to Display (1000 Nit) 39

163400 Display, (500 Nit) 7'' LCD

163399 Display, (1000 Nit) 7'' LCD 40

162272 Mounting Bracket (500 Nit)

162271 Mounting Bracket (1000 Nit) 41 58248 Nut, Lock 6-32NC Hex Nylon

42 169676

Controller Assembly (see Figure 2-43 on

page 48)

163787

Parts Kit 1280 Wall Mount (Includes items below)

44 169879 Ground Clip, Cord Grip PG13.5

172220 Plug, 3/8 Barb for Tubing 45 165111 Cord, US Power 46 165112 Cord, European Power

Item

No.

Part No. Description

Table 2-6. Replacement Parts - Wall Enclosure

Installation

Page 54

1280 Series Color Touchscreen Indicator

12 3 4

7689

Figure 2-43. Replacement Parts Drawing - Controller Assembly

Item No. Part No. Description

1 169350

2 166745 Fan Assembly, 60 mm x 10 mm DC 3 160758 Board Assembly, Backplate 4 44341 Screw, MACH 6-32 NC x 1/2'' lg 5 168591 Label, ESD Warning 6 169159 Extrusion Assembly 7 167190

162693 AC Power Supply

162694 DC/DC Power Supply 9 169354 Face Plate Assembly 10 160757 Board Assembly, CPU 11 169357 Face Plate, CPU PCB

167476 Label, AC Power

167477 Label, DC Power 13 14822 Screw, Mach 4-40NC x 1/4'' 14 163336 Cable, Antenna Bulkhead 15 168830 Terminal, Tab 1/4'' Push 16 153882 Conn, 5 Pos Screw Terminal 17 164918 Conn, 10 Pos Screw Terminal 18 170492 Battery, Rechargeable

162677 Connector for AC, 2 Pos Screw Terminal

15888 Connector for DC, 3 Pos Screw Terminal

Table 2-7. Replacement Parts - Controller Assembly

48 Visit our website www.RiceLake.com

Fan Mount Plate Assembly

Note: CPU, Rev A, Requires Rev A Fan Plate CPU, Rev B, Requires Rev A Fan Plate CPU, Rev C, Requires Rev B Fan Plate CPU, Rev D, Requires Rev C Fan Plate Note: When upgrading CPU board revisions, the fan plate must also be updated.

1280 Controller

Label,

Page 55

Item No. Part No. Description

20 14621 Nut, Kep 6-32 NC Hex 21 67550 Clamp, Ground Shield, Radius .125 inch 22 53075 Clamp, Ground Shield, Radius .078 inch 24 163327 Screw, Mach 6-32NC x 3/8'' 25 94422 Label, Capacity 26 163408 Blank Plate, Option Card Slot Cover 27 165927 Clip, Locking Load Cell (Kit PN 166957)

Table 2-7. Replacement Parts - Controller Assembly (Continued)

Installation

Page 56

1280 Series Color Touchscreen Indicator

Figure 2-44. Replacement Parts Drawing - 7 Inch Touch Only Panel Enclosure

Item No. Part No. Description

1 182145 Mounting Plate Assembly, 7-inch Panel Mount

176168 Display, Assembly, 7-inch Panel Mount

166725 Display Board (500 Nit)

166726 Display Board (1000 Nit) 3 180002 Cable, CPU to Touchscreen 4 58248 Locknut, 6-32NC Nylon Insert 5 67550 Clamp, Ground Cable Shield 6 55718 Screw, Machine 10-32NF x 1/4 Internal Tooth Washer 7 166838 DIN Rail Mount, 1280 CPU

164995 Cable, CPU to Display (500 Nit)

164970 Cable, CPU to Display (1000 Nit)

Table 2-8. Replacement Parts – 7 Inch Touch Only Enclosure

50 Visit our website www.RiceLake.com

Page 57

Installation

Figure 2-45. Replacement Parts – 12 Inch Touch Only Panel Enclosure

Item No. Part No. Description

1 176167 Panel Mount, Touch Only, 12-inch 2 179554 Mounting Bracket, 1280 3 55718 Screw, Machine 10-32NF x 1/4 pph internal tooth washer 4 165902 Label, 1280 Serial Tag 6 166838 Din Rail Mount 8 180002 Cable, CPU to Touchscreen 9 182992 Display, 12-inch

10 180001 Cable, CPU to Display

Table 2-9. Replacement Parts – 12 Inch Touch Only Panel Enclosure

Page 58

1280 Series Color Touchscreen Indicator

Maximum load (16) 350 Ω per A/D card

not to exceed (32) in this enclosure

Remove large ﬁllister screw in back

to tilt or remove controller

AC Power

DC Power

Class 2

3 4

CONNECTIONS

RELAY INTERFACE

ANALOG

OUTPUT/SINGLE

I+

I-

V+

V-

CHANNEL 1

ANALOG

OUTPUT/DUAL

I+

I-

V+

V-

CHANNEL 1

I+

I-

V+

V-

CHANNEL 2

ANALOG

OUTPUT/DUAL

+5V

GND

DIGITAL I/O

Sg+

Sg-

Sn+

Sn-

EX+

EX-

CHANNEL 1

Sg+

Sg-

Sn+

Sn-

EX+

EX-

CHANNEL 2

DUAL SCALE

Sg+

Sg-

Sn+

Sn-

EX+

EX-

CHANNEL 1

SINGLE SCALE

CHANNEL 1 CHANNEL 2

I+ T- T+

I-

V+

V-

I+ T- T+

I-

V+

V-

ANALOG

INPUT/DUAL

CHANNEL 1 CHANNEL 2

I+ TT+

I-

V+

V-

I+ TT+

I-

V+

V-

CTS/Z

Tx/A

Rx/B

GND

RTS/Y

CHANNEL 1 CHANNEL 2

CTS/Z

Tx/A

Rx/B

GND

RTS/Y

SERIAL COMM

87654321

GND

DIGITAL I/O

Slot 6 Slot 5 Slot 4 Slot 3 Slot 2 Slot 1

RTS CTS TX RX GND RTS CTS TX RX GND

CHANNEL 2 CHANNEL 1

STATUS OF CPU

HOSTDEVICE SD CARD

ETHERNET

10/100

HOSTDEVICE

RTS CTS TX RX GND RTS CTS TX RXGND

CHANNEL 2 CHANNEL 1

87654321

+ 5V

GND

DIGITAL I/O

SD CARD

ETHERNET

10/100

Note

2.11 Label Legend

Numbers 5-12 show position of labels on the option plate.

Figure 2-46. Replacement Parts - Labels

Item No. Part No. Description

1 167190 Label, 1280 Controller 2 168592 Label, Max Load (Universal Only) 3 167476 Label, AC Power 1280 4 167477 Label, DC Power 1280 5 167191 Label, Single Scale Option 6 167192 Label, Dual Scale Option 7 167193 Label, Digital IO Option 8 167194 Label, Serial Option

9 167195 Label, Relay Option 10 167196 Label, Analog Output (Single) Option 11 167197 Label, Analog Output (Dual) Option 12 167198 Label, Analog Input/Thermocouple (Dual) Option

Table 2-10. Replacement Parts - Labels

52 Visit our website www.RiceLake.com

Page 59

Configuration Menu

IMPORTANT

Note

Configuration Screw

Non-conductive Tool

Setup Switch

Panel Mount Enclosure

Setup Switch Configuration Screw

Configuration Screw

Setup Switch

Wall Mount Enclosure

3.0 Configuration Menu

Configuration has a series of menus that allow the parameters of the indicator to be set up. Detailed descriptions of the Scale Configuration, Communications, Features, Formats, Digital I/O, Analog Output, Setpoints and Diagnostics menu s are pr ovided in Section 4.0 through Section 11.0.

The audit trail jumper (JP1) needs to be disabled, in the off (right) position, in order to seal the setup switch with a lead wire seal. Access is not prevented simply by sealing the setup switch.

3.1 Access Setup Parameters

1. Press on the weigh mode screen. The Main Menu will display.

2. Press for access to the Configuration menu. If the Configuration menu does not appear, see the following note.

In order to access Configuration through the front panel (by pressing the button on the touchscreen, jumper JP1 needs to be in the on (left) position. In order to restrict access to Configuration using the front panel, JP1 needs to be in the off (right) position, requiring the setup switch to access Configuration. See Figure 3-3 on page 54.

3. Access to the configuration menu may be restricted with a password. If prompted, enter the password, then press

. The Configuration menu will display. See Section 3.3 on page 55.

See Section 6.4 on page 85 for more information on passwords.

3.2 Access Configuration Menu – Sealed Indicator

If the indicator has been sealed, there is a jumper in pl ace (JP1) that will not allow access to the configuration menu on the touchscreen. Use the following instructions to enter configura tion on a sealed indica tor.

1. Break the wire seal.

2. Re

3. Use a non-conductive tool to press the setup switch inside the indicator.

move the large fillister screw.

Figure 3-1. Setup Switch Location (Universal Enclosure)

Figure 3-2. Setup Switch Locations (Panel/Wall Mount Enclosures)

Page 60

1280 Series Color Touchscreen Indicator

TOP VIEW

1280 CPU Board

J17

J10

J11

JP1

J13

U13

JP3

ASSY

PN/Rev

RICE LAKE

CGND1

CGND2

BAT1

LVDS DISPLAY

DIO

ETHERNET

ANTENNA

PCIe

iMX6

KEYBOARD

POWER

CGND

MFGR

PORT#2

PORT#1

SERIAL

MFGR PN# VER. x.xxx

PCIe

WiFi-Blu

RX/B

GND

AUDIT TRAIL

OFF

uUSB-AB

DUAL

USB-A

Micro

SD Card

COM

DIO8

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

GND

PWR

RTS/Y

TX/A

-6V

CTS/Z

RTS/Y

TX/A

GND

+6V

RX/B

CTS/Z

CGND

JTAG

RESET

WD_RST

SIDE UP

INSERT

Light pipes and mounting plate removed for clarity.

Jumper JP1

Note

4. Access to the configuration menu may be restricted with a password. If prompted, enter the password, then press

. The configuration menu will display, see Section 3.3 on page 55.

Figure 3-3. Jumper Locations

The front door to the indicator may also be sealed to prevent access to the hardware. This may be required in some Legal for Trade applications.

54 Visit our website www.RiceLake.com

Page 61

3.3 Configuration Menu

VX.XX.XX

Configuration Menu

Figure 3-4. Configuration Menu

Item

No.

1 Scales Menu Set the scale parameter, see Section 4.0 on page 57. 2 Communications Menu Set the communication parameters, see Section 5.0 on page 70. 3 Features Menu Set features parameters, see Section 6.0 on page 78. 4 Formats Menu Set the print and stream format parameters, see Section 7.0 on page 89. 5 Digital I/O Menu Assign functions to digital inputs and outputs, see Section 8.0 on page 97. 6 Analog Outputs Menu Used to configure the analog output, see Section 9.0 on page 99. 7 Setpoints Menu Used to configure setpoints, see Section 10.0 on page 101. 8 Diagnostics Menu Recalibrate touchscreen and set the backlight, see Section 11.0 on page 115.

9 Save and Exit Button Press to save settings and return to weigh mode. 10 Import From File Press to import an existing file, see Section 13.0 on page 119. 11 Export to File Press to export files, see Section 13.0 on page 119. 12 Safely Remove USB Storage

Devices

13 Reset to Factory Defaults Press to restore all settings to factory defaults. 14 Partia lly Reset to Factory

Defaults

Selection Description

Press to release the USB connection before removing the flash drive or USB cable to ensure the drive continues to work properly and does not become corrupt.

Press to partially restore settings to factory defaults, this preserves Ethernet and scale settings.

Table 3-1. Configuration Main Menus

Page 62

1280 Series Color Touchscreen Indicator

Setpoint 1-100

Targets Preacts Actions Digital I/O Settings

Setpoints

Devices

Diagnostics

Scale 1-8 Filtering Setup MaintenanceFormat Calibration

Scales

Serial Ethernet Fieldbus

Communications

Analog Output X

Analog Out

Softkeys Locale Alibi StorageGeneral Regulatory Passwords Contact Info

Features

Print Formats Stream Formats

Formats

Slot X

Digital I/O

General

Advanced Printing

See Section 4.0

See Section 5.0

See Section 6.0

See Section 7.0

See Section 8.0

See Section 9.0

See Section 10.0

See Section 11.0

3.3.1 Configuration Menu Map

Figure 3-5 illustrates the menu structure in the configuration menu selections.

Figure 3-5. Configuration Menu Map

56 Visit our website www.RiceLake.com

Page 63

4.0 Scale Configuration

Press to Set Scale KindSelect the scale to configure

Select Scale Kind Being Configured

1 2

3 4 5 6

The Scales menu allows the setup of parameters for the type of scale to be set up.

Scale Configuration

From the Configuration menu, select the parameters have been set, press to return to weigh mode.

Scales icon (circled in Figure 4.1) to enter the Scales menu. Once all

4.1 Scale Kind

Figure 4-1. Select Scale Kind (Type)

Item

No.

1 None A scale kind will not be assigned to the scale number. 2 Analog Load Cell Scale An A/D scale card channel will be used for this scale (single or dual channel). 3

Total Scale

4 Analog Input Scale Version 1.07 – an analog input card 0-10 V, 0-100 mV, 0-20 mA, 4-20 mA will be used for this scale. 5 Legal for Trade Serial Scale A scale receiving a stream of legal for trade weight data over a serial or Ethernet connection. 6

Industrial Serial Scale

7 iQube2 Scale Scale is connected to 1280 via an iQube2 Junction Box, see Section 5.4 on page 77 8 Program Scale iRite program provides the scale data.

Parameter Description

The output of two or more scales can be configured to function as a Total Scale.

NOTES: The scale kind of a source scale cannot be changed once it is associated with a total scale.

A scale receiving a stream of weight data over a serial or Ethernet connection. Parameter values are configurable. Scale functions zero and tare can be used.

Table 4-1. Scale Kinds



Page 64

1280 Series Color Touchscreen Indicator

Associated Hardware is in Slot 1 using Channel 1

Scale Alias Button

Setup a Scale

1. Select the scale (1-8) to be configured from the drop-down menu in Figure 4-1.

2. Press to select the scale kind.

3. If applicable, a screen will open showing available hardware to associate with the selected scale kind (for example, an analog load cell scale will have hardware identified as slot and ch annel). Select the scale hardware to associate with the scale.

4. Press

. The Scale Kind menu displays and the associated hardware is listed to the right of the scal e kind

selected.

Figure 4-2. Scale Kind and Associated Hardware

5. Press .

6. Enter an alias name (optional). See Section 4.1.1.

4.1.1 Scale Alias

An alias (name) can be entered for use in an iRite program or to identify the scale.

Figure 4-3. Scales Alias Setup Screen

1. Press . The keyboard will display on the screen.

2. Use the keyboard to enter the desired alias (up to 16 characters).

3. Press when scale alias is correct.

58 Visit our website www.RiceLake.com

Page 65

Scale Configuration

Note

4.1.2 Scale Format

The Scale Format menu will vary depending on which scale kind is being used. Only settings available for the selected scale kind will display on the screen. Options specific to the scale feature chosen will show in blue font on the screen.

Parameter Default Description

Analog Input Type 0-10 VDC (Only Available in Analog Input Scale) Choose electrical signal type. Full Scale Capacity 10,000 Capacity of the scale in primary units.

Primary Units Enabled Primary Units Pounds (lb) Sets the units displayed or printed along with the scale weight. Primary Decimal Position

Primary Display Divisions

Secondary Units Enabled Secondary Units Kilograms (kg) Sets the units displayed or printed along with the scale weight.

Secondary Decimal Position 888888.8 Number of decimal places or fixed zeros to show for secondary units.

Secondary Display Divisions

Secondary Multiplier (Custom Units Only)

Tertiary Units Enabled Tertiary Units Kilograms (kg) Sets the units displayed or printed along with the scale weight.

Tertiary Decimal Position 888888.8 Number of decimal places or fixed zeros to show for tertiary units.

Tertiary Display Divisions

Tertiary Multiplier (Custom Units Only)

Custom Units One — Custom Units Two — Custom Units Three — Split Mode Off Multi-Range, Multi-Interval Settings; see Section 4.1.3 for more information.

8888888 Number of decimal places or fixed zeros to show for primary units. The default is 8888888

1 The division the scale counts by as the load changes. This setting is associated with the

Off When set to Off, the Units key will not select this unit of measure to perform a weight con-

5 The division the scale counts by as the load changes. This setting is associated with the

1 Use with custom units. It is the conversion factor applied to the primary units to convert

Off When set to Off, the Units key will not select this unit of measure to perform a weight con-

5 The division the scale counts by as the load changes. This setting is associated with the

1 Use with custom units. It is the conversion factor applied to the primary units to convert

The

1280 is calibrated in Primary Units. When set to Off, primary units will not be dis-

played, but are still being evaluated in the background for all conversion functions.

(no decimal places).

Primary Decimal Position. 

Example: If the Decimal Position is set to 88888.8 and the Display Divisions are set to 5, it will count by 0.5 units.

version.

secondary decimal position.

Example: If the Decimal Position is set to 88888.8 and the Display Divisions are set to 5, it will count by 0.5 units.

weight for custom units. Example: If primary units were lb and secondary custom units were gallons, there would be a secondary multiplier of 8 entered to show the relationship between lb and gallons.

version.

tertiary Decimal Position.

Example: If the Decimal Position is set to 88888.8 and the Display Divisions are set to 5, it will count by 0.5 units.

weight for custom units. Available to enter a name for custom units. Maximum length is 8.

Table 4-2. Scale Format

Defaults are shown for NTEP mode.

Page 66

1280 Series Color Touchscreen Indicator

Note

4.1.3 Split Mode

The 1280 supports multi-range and multi-interval scales of either two or three ranges or intervals. To set up Multi-Range or Multi-Interval, select menu. Press

Parameter Description

Multi-Range

Multi-Interval

Low Range Capacity (MRMI) will display once Split Mode is set to either Multi-Range or Multi-Interval.

Parameter Default Description

Low Range Capacity (MRMI)

Low Range Decimal Position 8888888 Number of decimal places or fixed zeros to show for low range.

Low Range Display Division

Mid Range Capacity (MRMI) Mid Range Decimal Position 8888888 Number of decimal places or fixed zeros to show for mid range.

Mid Range Display Division

If two ranges are used, then:

• Low Range Capacity is set for range 1 capacity

• Full Scale capacity is set for range 2 capacity

If three ranges are used, then:

• Low Range Capacity is set for range 1 capacity

• Mid Range Capacity is set for range 2 capacity

• Full Scale Capacity is set for range 3 capacity

Split Mode from the Scales Format menu. Select Off, Multi-Range or Multi-Interval from the Split Mode

Done.

Provides two or three ranges, each extending to the maximum capacity specified for each range. The scale display division changes as the applied weight increases, but does not reset to lower display divisions until the scale returns to center of zero.

Divides the scale capacity into two or three partial weighing intervals, each with different display divisions. The intervals extend to the maximum capacity specified for each interval. The display divisions change with both increasing and decreasing loads.

Table 4-3. Split Mode Parameters

0 Low range capacity of the scale in primary units. This parameter must be set before the

indicator will display Low Range Decimal Position, Low Range Display Division or

Mid Range Capacity (MRMI).

1 The division the scale counts by as the load changes. This setting is associated with the

Low Range Decimal Position. Example: If the decimal position is set to 88888.8 and the display divisions are set to 5, it will count by 0.5 units.

0 Mid range capacity of the scale in primary units. This parameter must be set before the

indicator will display Mid Range Decimal Position or Mid Range Display Division.

1 The division the scale counts by as the load changes. This setting is associated with the

Mid Range Decimal Position. Example: If the decimal position is set to 88888.8 and the display divisions are set to 5, it will count by 0.5 units.

Table 4-4. Split Mode Sub-menus

Configure a Multi-Range or Multi-Interval Scale

1. Select Multi-Range or Multi-Interval.

2. Press . The Low Range Capacity (MRMI) parameter will appear in blue text under Split Mod e.

3. Press Low Range Capacity (MRMI) to set a low range capacity. Setting a low range capacity is the only way to access the Low Range Decimal Position, Low Range Display Division and Mid Range Capacity (MRMI) parameters. These parameters will appear in blue text under Low Range Capacity (MRMI) after a low range capacity has been set.

A Low Range Capacity must be set in order for further parameters to display. The Full Scale Capacity is either the second or third range.

4.Set the Low Range Decimal Position and Low Range Display Divisions as desired.

5. (Optional) If desired, the Mid Range Capacity (MRMI) can be set at this point. A mid range capacity must be set to

60 Visit our website www.RiceLake.com

Page 67

access the Mid Range Decimal Position and Mid Range Display Division parameters. These parameters will appear in

Range 1: Up to 100 lb will count by 1 lb

Range 2: 100 to 500 lb will count by 5 lb

Range 3: 500 lb to capacity will count by 10 lb

Note

blue text under Mid Range Capacity (MRMI) after a mid range capacity has been set.

6. Calibrate scale. See Section 4.2 on page 61.

Scale Configuration

Figure 4-4. Multi-Range Example

When using Multi-Range, the last count-by reached is held until returning to zero, even when descending through other ranges. When using Multi-Interval, count-by change both when ascending and descending through other intervals.

4.2 Scale Calibration

To enter Scale Calibration, press the Scales icon . From the Scales menu, select Calibration. The following parameters are available.

Parameters Defaults Description

Zero Calibration Counts 8386509 Calculated during calibration, it is the number of A/D counts after the zero calibration. Span Calibration Weight Span Calibration Counts 2186044 Calculated during calibration, this is the A/D count captured at the span/WVAL weight.

Capacity Calibration Counts

Linear Point Weight 1-4 Linear Point Counts 1-4 0 The A/D count captured at the linear point weight.

Linear calibration points provide increased scale accuracy by calibrating the indicator at up to four additional points between the zero and span calibrations.

10,000 Display and edit the test weight value. Press Calibrate to calibrate the Span Calibration

Point. See Section 4.2.1 on page 62 for more information on Span Calibration.

2186044 Calculated during calibration, this is the A/D count at full scale capacity.

Note: If the scale is calibrated at full capacity, then Span Calibration Counts = Capacity Calibration Counts.

0 The test weight value for the linear calibration point. Press Calibrate to calibrate the Linear

Calibration Point, or Remove to remove it.

Table 4-5. Calibration Menu

The button begins a step-by step procedure for calibration. See Section 4.2.1.

Page 68

1280 Series Color Touchscreen Indicator

1 2

4.2.1 Standard Calibration

Use the following steps to perform a standard calibration on a scale.

1. Select the scale to be calibrated and enter the calibration menu.

2. Press .

3. Select the method of calibration. Press . For other methods calibration see:

•Section 4.2.2 for multi-point calibration,

•Section 4.2.3 for last zero calibration and

•Section 4.2.4 for temporary zero calibration.

•Section 4.2.5 for Theoretical Calibration

4. Select whether or not chains, hooks or other items used for applying weights will be u sed during calibration. Press

5. Remove all weight from the scale except for chains and hooks (if used).

6. Press . The current weight and Zero Calibration Complete displays.

7. Press .

8. Enter Span weight for the value of the calibration test weights that will be used to calibrate the scale. This is required prior to running the span calibration.

Figure 4-5. Calibrate Span

Item

No.

1 Calibration Weight Window – Displays calibration weight value. 2 123... – Press to enter or edit the calibration weight value. Increments based on scale division size or the expanded resolution. 3 Calibrate Span – Press to calibrate span. 4 Up – Calibration can be adjusted by changing the calibrated weight. Press Up to adjust the calibrated weight value up by one

display division. Use the Expanded Resolution to adjust the calibrated weight value by a 10th of a display division

5 Down – Calibration can be adjusted by changing the calibrated weight. Press Down to adjust the calibrated weight value down

by one display division. Use the Expanded Resolution to adjust the calibrated weight value by a 10th of a display division

6 Expanded Resolution – Increases the resolution by a factor of 10.

Table 4-6. Calibrate Span

Description

62 Visit our website www.RiceLake.com

Page 69

Scale Configuration

Re-Zero

9. With the test weight on the scale platform and the test weight value entered into the calibration weight window, the corresponding scale span value is ready to be calibrated.

10. Press . The current span weight will display.

11. Press . Calibration results are displayed.

12. Press . Display returns to the Calibration menu.

13. The re-zero function is used to remove a calibration offset when hooks or chains are used to hang the test weights during both zero and span calibration. If hooks or chains were used during calibration, remove these and the test weights from the scale.

14. With all weight removed, p r ess .

4.2.2 Multi-Point Calibration

A multi-point calibration is performed by entering up to four additional calibration points.

Figure 4-6. Multi-Point Calibration

Item

No.

1 123... – Press to enter the test weight value. 2 Press to Calibrate – Captures the calibration value for each point. Only available after a test weight value has been entered. Dis-

plays Calibration Complete after the calibration is finished.

Table 4-7. Multi-Point Calibration

Description

Multi-Point Calibration

• If multi-point values have previously been entered, values are reset to zero when the initial zero calibration is performed.

• Zero Calibration and Span Calibration need to be performed before ad ding linearization points.

• Linear values must not duplicate Zero Calibration, Span Calibration or previous linear points.

4.2.3 Last Zero Calibration

This takes the last pushbutton zero in the system (from weigh mode) and uses it as the new zero reference point, after which a new span calibration must be performed. This calibration cannot be performe d when calibrating a scale for the first time.

A last zero calibration is typically used on truck scales to remove the test weights.

allow a scale verification to become a calibration without having to

Page 70

1280 Series Color Touchscreen Indicator

4.2.4 Temporary Zero Calibration

Temporary zero calibration temporarily zeros the displayed weight of a non-e mpty scale. After span calibration, the difference between the temporary zero and the previously calibrated zero value is used as an offset.

A temporary zero calibration is typically used on hopper scales to cal

ibrate the span without losing the original zero calibration.

4.2.5 Theoretical Calibration

Figure 4-7. Calibration Selection Screen

1. Select Theoretical Calibration from the calibration screen. The Calibrate Zero screen displays.

2. Remove all test weights from the scale.

3. Press . The current weight and Zero Calibration Complete displays.

4. Press . The Total Load Cell Build screen displays.

5. Enter the total load cell build in primary units.

6. Press . The Average mV/V screen displays.

7. Enter the average of the mV/V of all the load cells in the scale.

8. Press . The Calibration Results screen will display.

9. Press . The calibration menu displays.

4.3 Scale Filtering

Digital filtering can be used to create a stable scale reading by removing environmental influences. The 1280 has two filtering methods that can be selected; Adaptive Digital and Three Stage Filtering. Three Stage Filtering is selected by default. In addition, the A/D sample rate and damping time constant can be set in this menu.

64 Visit our website www.RiceLake.com

Page 71

Scale Configuration

To enter scale filtering, press the Scales icon . From the Scales menu, select Filtering. The following parameters are available.

Parameter Default Description

30 Hz Selects measurement rate, in samples per second, of the analog-to-digital converter.

Sample Rate

Digital Filter Type Damping Time Constant

(seconds)

Three Stage Filter Sets the filter type to be used. See Section 4.3.1 for more information on the adaptive digi-

0.01 Used for flow control to get a smooth increase in weight. It takes two-thirds of the differ-

The sample rate refers to how many times per second the analog signal is converted to digital. It should be set first. Better stability is achieved with a lower sample rate setting, so

7.5 Hz is more stable than 960 Hz.

tal filter. See Section 4.3.2 for more information on the three stage filter.

ence in weight change in each time period specified.

Table 4-8. Filtering Menu Descriptions

4.3.1 Adaptive Digital Filter

The adaptive digital filter has two parameters to set the response time and observe noise (instability): Filter Sensitivity and Filter Threshold (Display Divisions). These parameters display in blue text after the Digital Filter Type is set to Adaptive Digital Filter.

Parameter Default Description

Light Controls the stability and response time of the scale.

• Heavy – results in an output that is more stable but will settle slowly. Small changes in

Filter Sensitivity

10 Digital filter cutout threshold (in display divisions). A weight change exceeding the threshold

Filter Threshold

weight data (a few grads) on the scale base will not be seen quickly.

• Medium – has a quicker response time than heavy, but more stability than light.

• Light – fastest response to small weight changes, but less stable.

will reset the filtered values. Must be set above the noise disturbances in the system. If set to zero, the filter is disabled.

Table 4-9. Adaptive Digital Filter Menu Descriptions

Filtering Threshold

Digital filtering threshold should be set for the amount of observed noise in the system. This parameter can be set in the range of 0 to 99999 display divisions. When a new sampled weig ht value is acquired, the adaptive digital filter compares the new value to the previous (filtered) output value. If the difference between the new value and the previous output value is greater than the Threshold parameter (displayed division), the adaptive digital filter output is reset. The newly acquired sample value replaces the filtered output. If the difference between the new value and the previous output value is less than the parameter, the two values are averaged together using a weighed average. The weighed average is based on the time the system has been stable and the selected sensitivity setting.

The filter can be set to

Off by entering 0 in the Threshold parameter.

1. To determine the initial setting for the threshold, first set the value to 0.

Example: If a heavy-capacity scale (10000 x 5 lb) produces vibration-related readings of up to 50 lb, with occasional spikes to 75 lb, record 50 lb as the threshold weight value.

2. In weigh mode, determine the amount of instability that is present. Convert this instability to display divisions.

3. Set the threshold to the number of display divisions of instability.

threshold_weight_value / display_divisions

In the example in Step 2, with a threshold weight value of 50 lb and a display divisions value of 5 lb: 50 / 5 = 10. Threshold should be set to 10D for this example.

4. Further tweak this value, along with the sensitivity, to achieve the desired results. Set sensitivity for the desired response for weight changes; light for less stable but quicker responses, heavy for more stable but slower responses.

Threshold



Page 72

1280 Series Color Touchscreen Indicator

4.3.2 Three Stage Filter

The Three Stage Digital filter is a simple rolling average filter with three successive stages. The values assigned to each of the three stages determines the number of A/D readings averaged by that stage. Th e output value of each stage is passed on to the next stage at each A/D update. The overall filtering effect can be expressed by adding the values assigned to the filter stages and subtracting two.

Example: If the filter stages were set to 16, step change on the input would be fully realized on the display in 22 A/D samples. Setting the filters to 1 ((1+1+1)-2=1) effectively disables the Three Stage Filter.

Parameter Default Description

Filter Sensitivity 2 Consecutive Values

Filter Threshold None

Stage One Filter Value 4 Selects the digital filtering rate used to reduce the effects of environmental influences Stage Two Filter Value 4

Stage Three Filter Value 4 RattleTrap Off Enables RattleTrap filtering.

4 and 4, the overall filtering effect is 22 ((16+4+4)-2=22). With this configuratio n, a

Specifies the number of consecutive A/D readings that must fall outside the Filter Threshold before filtering is suspended.

Sets a threshold value, in display divisions. When a number of consecutive A/D readings (Filter Sensitivity) falls outside of this threshold value (when compared to the output of the filter), filtering is suspended and the A/D value is sent straight through the filter. Filtering will not be suspended if the threshold is set to None.

from the immediate area of the scale. Choices indicate the number of A/D conversions per update that are averages to obtain the displayed reading. A higher number gives a more accurate display by minimizing the effect of a few noisy readings, but slows down the response time of the indicator.

Table 4-10. Three Stage Digital Filter

Filter Sensitivity and Threshold

The Three Stage Digital filter can be used by itself to eliminate vibration effects, but heavy filtering also increases response time. Filter Sensitivity and Threshold can be used to temporarily override filter averaging to improve response time.

Setting the Digital Filter Parameters

Use the following procedure to determine vibration effects on the scale and optimize the digital filtering configuration.

1. In setup mode, set the digital filter parameters to 1. Set Filt

er Threshold to None. Return indicator to weigh mode.

2. Remove all weight from the scale. Watch the indicator display to determine the amount of stability of the scale. Record the weight below which all but a few readings fall. This value is used to calculate the Threshold parameter value in Step 4.

Example, if a heavy-capacity scale (10000 x 5 lb) produces vibration-related readings of up to 50 lb, with occasional spikes to 75 lb, record 50 lb as the threshold weight value.



3. Place the indicator in setup mode and set the Stage Filter Value parameters to eliminate the vibration effects on the scale. (Leave Threshold set to NONE.) Find the lowest effective value for the Stage Filter Value parameters.

4. Calculate the Threshold parameter value by converting the weight value recorded in Step 2 to display divisions:

threshold_weight_value / display_divisions

In the example in Step 2, with a threshold weight value of 50 lb and a display divisions value of 5 lb: 50 / 5 = 10. Threshold should be set to 10D for this example.

5. Set the Sensitivity parameter high enough to ignore transient peaks. Longer transients (typically caused by lower vibration frequencies) will cause more consecutive out-of-band readings, so Sensitivity should be set higher to counter low frequency transients. Reconfigure as necessary to find the lowest effective value for the Sensitivity parameter.

RattleTrap

RattleTrap filtering uses a vibration-dampening algorithm to automatically provide the best features of digital filtering. It is particularly effective for eliminating vibration effects or mechanical interference from nearby machinery. Using RattleTrap filtering can automatically eliminate environmental influences, but will usually increase response time over standard digital filtering. If RattleTrap is set to on, sensitivity and threshold parameter settings are ignored.

66 Visit our website www.RiceLake.com

Page 73

Scale Configuration

4.4 Scales Setup

To enter the Scales Setup menu, press the Scales icon . From the Scales menu, select Setup. The following parameters are available.

Parameter Default Description

Tare Function Both Enables or disables push-button and keyed tares.*

1 Sets the level at which scale motion is detected. If motion is not detected for the standstill time

Motion Band (Display Division)

Overload Range Initial Zero Range (% of

Capacity) Zero Track Band (Dis-

play Divisions) Zero Range (% of

Capacity) Minimum Print Weight Standstill Time (Sec-

onds) Accumulator

Peak Hold

Rate of Change Decimal Point

Rate of Change Time Unit

ROC Capture Window (Seconds)

Powerup Mode

Visible On Specifies whether scale data is displayed.

Full Scale + 2% Determines the value, in a percentage/display division above capacity, in which the display

0 When the indicator is turned on and the weight value is between the ± percent range specified

0 For small weight changes around zero, the zero track band is the value that can automatically

1.9

0 The minimum print weight is the weight value that the scale must be above to allow a print.

1.0 Specifies the time (in seconds) that the scale must be out of motion before it is considered to

Off Accumulation can be toggled On/Off. If on, accumulation occurs on print operation; if off, an

Off Used to determine, display and print the greatest weight read during a weighing cycle.

8888888

Seconds

1.0

Go When the indicator is turned on, it performs a display test, then enters a warm up period.

* Maximum legal value of these parameters varies depending on local regulations.

or longer, the standstill icon displays.*

• It is shown in display divisions between 1-100.

• If set to 0, the standstill icon is on at all times and operations including zero, print, and tare will be performed regardless of scale motion. If set to 0, it will not be Legal for Trade certified.

blanks and the out-of-range error message is displayed.*

in Calibrated Zero, the indicator will automatically zero off that weight.*

be tracked off to return the scale to zero. It is entered in display divisions.* Zero range specifies the percent of capacity at which the scale can be zeroed.*

When set to zero, it is disabled.

be at standstill.*

accumulation does not occur.

The weighing cycle ends when a print command is executed (AUTO setting) or when the peak weight is cleared by pressing Zero or Print. Press Gross/Net to display gross weight data when using the peak hold function.

• Off - Peak hold function is off.

• Normal - Positive peak, manual reset. Greatest net weight is held in memory until the weight is removed from the scale when either the Zero or Print key is pressed.

• Bi-directional - Bi-directional peak, manual reset. Same as Normal, but peak value can be either positive or negative, determined by absolute value.

• Automatic - Positive peak, auto print, auto reset. Automatic print occurs when the scale load is 0 ± 10 display divisions and at standstill. Following the print command, the peak value is cleared and reset automatically.

Set decimal position for rate of change. The default is 8888888 (no decimal point).

Time unit to be used in rate of change.

The time over which the rate of change is calculated.

• If no motion is detected during the warm up period, the indicator will become operational when the warm up period ends.

• If motion is detected, the delay timer is reset and the warm up period is repeated.

4-11. Scales General Descriptions

Table

Page 74

1280 Series Color Touchscreen Indicator

Note

4.5 Maintenance

To enter the Scales Maintenance menu, press the Scales icon . From the Scales menu, select Maintenance. The following parameters are available.

Parameter Default Description

Weighment Threshold 100 The amount of weight that, when exceeded, increments the Number of Weighments. Number of Weighments 0 Displays the total number of weighments (read only). Maximum Weighment 0 Displays the maximum weighments allowed (read only). Date of Maximum Weighment — Displays the date the maximum weighment occurred (read only).

Table 4-12. Scales Maintenance Menu

4.6 Serial Scale Type

The Serial Scale type allows other scale indicators to send gross or net weig ht data to the 1280 using a continuous stream of data through a communications port.

4.6.1 Legal for Trade

For a Legal for Trade serial scale, the data must contain the unit of measure, mode of operation and status (in addition to the weight). The configuration of a Legal for Trade serial scale is very limited as it acts similarly to a remote display. For this reason, the scale cannot be tared or zeroed on the 1280 but must be done on the host indicator.

If the data packet for a Legal for Trade serial scale does not contain all the necessary information, or the information is incorrect

, the scale will show an error.

4.6.2 Industrial Scales

For industrial scales, the only data needed is the gross weight. The data can (but does not need to) include the unit of measure, mode or status. If the unit of measure is included, it can be used to change the capacity label on the 1280 display. If not, the 1280 will always assume it is primary units.

If the mode is included, the scale will display an error if anything other than the gross mode is indicated. If the mode is not

ded, the weight is assumed to be gross.

inclu If status is included, it is ignored with the exception of the center of ze ro indicator. The serial scale cannot determine if the

ading is within the center of zero band. The only way to show the ce nter of zero ba nd is to have the h ost indicator include t hat

re information (using the status token) in the data.

Though the 1280 ca

nnot zero an industrial serial scale (zeroing must take place on the host in dicator), it is possible to take a

tare and display the resulting net weight.

Digital filtering is available with the use of an industrial serial scale. If digital filtering is enabled and the display division size of the incoming weight data is greater than the display division size of the industrial serial scale configuration, the displayed weight will count by the smaller division size, due to the averaging nature of the filters.

4.6.3 Configuration

The 1280 supports serial scale data input on any of the RS-232/RS-485 ports, as well as the Ethernet TCP/IP.

1. In the Communications menu, select the desired port.

2. Set the Input Type to either Legal for Trade or Industrial Serial Scale. Set the remaining parameters as necessary to match the parameters of the incoming serial data.

3. In the Scales menu, set the scale kind of the scale to either Legal for Trade Serial Scale or Industrial Serial Scale.

4. Select the communication port to link to the selected scale. Only communications ports that have been configured as serial scales will be displayed.

5. Set the capacity, decimal point, count-by and units to match that of the incoming data. This is done so the capacity label (shown on the display near the weight) is correct. To configure the actual format of the data, go to the Scales/ General tab and select a stream format (1-4).

6. Navigate to the Formats menu, and select Stream Formats.

68 Visit our website www.RiceLake.com

Page 75

Scale Configuration

Note

7. Select the format (1-4) in the left pane. The current stream format will be shown. Either select one of the pre-defined built-in formats, or create a custom format to match the input data format. If necessary, set the token values. See

Section 7.2 on page 93 for more information about configuring the stream format.

If using a Legal for Trade serial scale, there are additional settings under the Scales/General tab; these include enabling the accumulator and visibility. If using an industrial serial scale, there are additional general settings for the tare function, overload and motion determination, as well as filter settings under the Scales/Filtering tab.

The flow of data into the indicator must be continuous – if the flow is interrupted for more than a second, the scale will show an error.

No matter the type, if the data received does not match exactly that which is expected (as defined by the stream format configuration), the data is thrown out and the scale will show an error.

Page 76

1280 Series Color Touchscreen Indicator

Scroll for additional parameters.

5.0 Communications

The Communications menu is used for the setup of communication parameters for the 1280. From the Configuration menu, select the Communications icon

menu. Once all parameters have be

en set, press to return to weigh mode.

(circled in Figure 5-1) to enter the Communications

Figure 5-1. Communications Menu

Item No. Parameter Description

1 Serial To set Serial parameters, see Section 5.1 on page 71. 2 Ethernet To set Ethernet parameters, see Section 5.2 on page 72. 3 Fieldbus To set Fieldbus parameters, see Section 5.3 on page 76 4 Selection Field Allows selection of port or server for items 1, 2 or 3. 5 General General parameters for items 1, 2 or 3. 6 iQube2 Select to enter iQube2 setup, see Section 5.4 on page 77.

Table 5-1. Communication Menu Parameters

70 Visit our website www.RiceLake.com

Page 77

5.1 Serial Menu

Scroll for additional parameters.

Press arrow for complete list of Serial Ports

The Serial menu is used for the setup of communication ports.

Figure 5-2. Serial Menu Screen

Communications

Serial Port 1 Communications port support RS-232, RS-422 and RS-485 (connector J6). Serial Port 2 Communications port support RS-232, RS-422 and RS-485 (connector J7). USB Port (Port 3) Micro USB device port that can be used as a communications port via a micro USB type B connector.

Bluetooth Serial Port 5-16 Dual serial option card ports (if installed). Supports RS-232, RS-422 and RS-485.

Input Type Command Processor Sets the input type. Baud Rate 115200 Selects the transmission speed for the port. Data Bits 8 Selects number of data bits transmitted or received by the port. Parity None Sets parity bit to odd, even or none. Stop Bits 1 Selects the number of stop bits transmitted or received by the port. Handshake Off Specifies if XON/XOFF flow control characters are used.

Port Type

Alias — Allows the serial port to be renamed. Echo

1. Press from the communications screen.

2. Select Serial, to enter the Serial menu.

3. Select the port to be used by pressing the selection list arrow next to the serial port. The parameters in Table 5-2 are available.

4. Set the parameters as needed for the selected port. See Table 5-3. Parameters will vary dependent on which port is being used.

Parameter Description

Port (Port 4) Bluetooth® wireless communication port supporting the Serial Port Protocol (SPP) only.

Table 5-2. Available Ports

Parameter Default Description

RS-232 Designates what Serial Port type is used (RS-232, RS-485, or RS-422).

Note: If RS-485 is selected, prompts are shown to select Duplex (half or full) and RS-485 Network Address.

On Specifies whether characters received by the port are echoed back to the sending

unit.

Table 5-3. Serial Port Parameters

Page 78

1280 Series Color Touchscreen Indicator

Press arrow for complete list of connections

Note

Parameter Default Description

Response On Specifies whether the port transmits replies to serial commands. Outgoing Line Termination CR/LF Selects termination character for data sent from the port.

End of Line Delay (seconds)

iQube2 Sample Rate

0.0 Sets delay period from when a formatted line is terminated to the beginning of the next formatted serial output. Range acceptable is 0.0-25.5 seconds.

30 Hz Sets the rate at which the 1280 polls the iQube2 for weight data. It is only visible

when Input Type is set to iQube2.

Table 5-3. Serial Port Parameters (Continued)

5.2 Ethernet Menu

The Ethernet menu is used for the setup of wired and Wi-Fi Ethernet connections, including Wi-Fi Direct. These are used to connect the 1280 to local area networks (WLAN and LAN). Network information can be found in weigh mode by pressing the Wi-Fi symbol or in the

Ethernet menu in Configuration Mode.

Figure 5-3. Ethernet Screen

1. Press the Communications icon .

2. Select Ethernet.

3. Press the selection field arrow to expand the Ethernet selections.

4. Select the desired Ethernet option (Table 5-4).

5. Set the parameters associated with the Ethernet type selected.

Parameter Description

Wired Adapter General wired Ethernet settings

Wi-Fi

Adapter TCP Command Server Specific settings for the TCP Command Server Stream Server Specific settings for the Stream Server TCP Client 1 Specific settings for TCP Client #1 TCP Client 2 Specific settings for TCP Client #2

Contact the IT department if unsure about the required Ethernet settings for a specific network.

General Wi-Fi settings, Wi-Fi Direct

Table 5-4. Ethernet Selections

72 Visit our website www.RiceLake.com

Page 79

Communications

5.2.1 Using an Internet Browser as a Remote Display

A virtual display can be viewed on a computer or mobile device using an Internet browser that support s HTML 5 and JavaScript, such as Internet Explorer v10 and newer, Chrome v30 and newer or Firefox v32 and newer. In addition to viewing, virtual keypad elements can be activated by clicking on them in the browser window.

To use this feature, the 1280 a

nd computer/mobile device must be connected to the same network. In the browser’s address

bar (URL), type the 1280’s IP address using TCP port 3000.

Example: If the 1280's IP address is 192.168.0.1, then navigate the browser to http://192.168.0.1:3000.

5.2.2 Resetting the Network Connection

If the Network connection needs to be reset for any reason, press . The available network information is displayed.

Figure 5-4. Network Information Options Screen

1. Select Wired Ethernet or either Wi-Fi tab.

2. Press

Network Restart.

3. A prompt is displayed, Do you want to restart all network connections? Select

4. Selecting

Yes connects to a known network connection and will then be restarted.

5.2.3 Wired Adapter

When Wired Adapter is selected, the parameters in Table 5-5 will display.

Parameter Default Description

Enabled

DHCP

IP Address 0.0.0.0 Enter a four field value. The range of each field is 0-255. Subnet Mask 255.255.255.0 Specifies the subnet mask. Primary DNS Server 0.0.0.0 IP address for the server. Secondary DNS Server 0.0.0.0 IP address for the server. Gateway Address 0.0.0.0 Default gateway. MAC Address — View the MAC Address, in hexadecimal base (read only).

Off Enable Wired Ethernet Communications – Off speeds up the booting process

and configuration mode to weigh mode transitions.

On Dynamic Host Configuration Protocal:

On – Dynamic allocation of IP address. Off – Static allocation of IP address.

Table 5-5. Wired Adapter Parameters

Yes or No.

Page 80

1280 Series Color Touchscreen Indicator

Wi-Fi need not be enabled for WiFi Direct to be enabled.

Note

Figure 5-6.

Busy Wheel

5.2.4 Wi-Fi Adapter

When Wi-Fi Adapter is selected, the parameters in Table 5-6 will display.

Parameter Default Description

Enable Service Set ID (SSID) — Name of the wireless local area network (WLAN).

Network Type Infrastructure Type of wireless network. Choose infrastructure for connections to wireless networks. Security Type WPA-Personal Wireless security protocol. Encryption Type TKIP Wireless encryption protocol. Security Key — Password to access a local area network.

DHCP

IP Address 0.0.0.0 Four field value, the range of each field is 0-255. Subnet Mask 255.255.255.0 Specifies the subnet mask. Primary DNS Server 0.0.0.0 IP address for the server. Secondary DNS Server 0.0.0.0 IP address for the server. Gateway Address 0.0.0.0 Default gateway. MAC Address — View the MAC Address, in hexadecimal base (read only).

Wi-Fi Direct Enabled

Off Enable Wi-Fi Ethernet Communications – Off speeds up the booting process and configura-

tion mode to weigh mode transitions.

On Dynamic Host Configuration Protocal

On – Dynamic allocation of IP address Off – Static allocation of IP address

Off Allows wireless connection directly to a PC, phone or tablet without a network or access

point.

Table 5-6. Wi-Fi Adapter Parameters

5.2.5 Wi-Fi® Direct

Wi-Fi Direct is a feature of Wi-Fi that allows wireless connection directly to a PC, phone or tablet.

Figure 5-5. Enable Wi-Fi Direct

1. Select Ethernet.

2. Press the selection field arrow to expand the Ethernet choices.

3. Select the Wi-Fi® Adapter list option.

4. Enable the Wi-Fi Direct option.

5. Press . The Busy Wheel will display for a few seconds, then the display will go back to the weigh mode.

74 Visit our website www.RiceLake.com

Page 81

Communications

Note

6. Press . The available Network Information is displayed.

Figure 5-7. Wi-Fi Options Screen

7. Select the Wi-Fi Direct tab.

8. Press

Initiate Wi-Fi Direct.

9. Wi-Fi Direct will be assigned an SSID and Password. Write these down, they will be required when connecting to another device.

A new SSID and Password will be created each time a Wi-Fi Direct connection is initiated.

Figure 5-8. SSID and Password for Wi-Fi Direct

10. Press . The weigh screen is displayed.

11. Using the PC, mobile phone or iPad /tablet, enter settings, then Wi-Fi selections. The name of the 1280 SSID should be displayed as an option in the Wi-Fi selections.

12. Select the 1280 SSID from the list, a screen will display asking for the Password.

Page 82

1280 Series Color Touchscreen Indicator

Note

13. Enter the Password from Step 9.

14. To disable Wi-Fi Direct, go back to the communications/Ethernet menu to disable.

Using Wi-Fi Direct does not interrupt the use of Wi-Fi. Enabling the Wi-Fi will require Wi-Fi Direct to be re-initiated. Wi-Fi direct can utilize all Ethernet connection types (TCP command server, Stream Server, TCP Client 1 & 2)

5.2.6 TCP Command Server

Parameter Default Description

Input Type Command Processor Sets the input type. Server Port Number 10001 TCP/IP port number. Alias — Allows the server to be renamed. Echo Off Specifies whether characters received by the port are echoed back to the sending unit. Response Off Specifies whether the port transmits replies to serial commands. Outgoing Line Termination CR/LF Selects the termination character for data sent from the port.

Table 5-7. TCP Command Server Parameters

5.2.7 Stream Server

Parameter Default Description

Server Port Number 20001 Stream server port number. Alias — Allows the server to be renamed. Outgoing Line Termination CR/LF Selects termination character for data sent from the port.

Table 5-8. Stream Server Parameters

5.2.8 TCP Client 1 & 2

Parameter Default Description

Input Type Command Processor Sets the input type. Remote Address 0.0.0.0 IP address of the remote unit that will connect to the 1280. Remote Port Number 10001 TCP port number on the remote unit that will connect to the 1280. Alias — Allows the server to be renamed. Outgoing Line Termination CR/LF Selects termination character for data sent from the port. End of Line Delay

(seconds) Echo Response On Specifies whether the port transmits replies to serial commands.

Disconnect Time (seconds) 0 The amount of time an active connection is held before it is dropped. iQube2 Sample Rate

0.0 Sets the delay period, in 0.1 second intervals, from when a formatted line is terminated to the beginning of the next formatted serial output.

On Specifies whether characters received by the port are echoed back to the

sending unit.

30 Hz Sets the rate at which the 1280 polls the iQube2 for weight data. It is only visi-

ble when the Input Type is set to iQube2.

Table 5-9. TCP Client 1 & 2 Parameters

5.3 Fieldbus Menu

The Fieldbus menu allows the selection of the slot (1-6) to be used for one of the CompactComm Options.

1. Press the Communications icon .

2. Select Fieldbus.

76 Visit our website www.RiceLake.com

Page 83

Communications

3. Press the arrow next to the Slot # and select the slot required.

Parameter Default Description

Data Swap None Specifies Byte, Word, Both or none of the data sent and received by the fieldbus card. iRite Fieldbus Data Size

(Bytes) (0=disabled) DeviceNet Address 63 Enter DeviceNet option address 1-64. Profibus Address 126 Enter Profibus option address 1-126.

0 Specifies the data size, in bytes,that the iRite Fieldbus command handler transfers. Values must

be in multiples of four.

Table 5-10. Fieldbus Menu Descriptions

5.3.1 Data Swap

If the values returned from the 1280 do not appear to be correct, change the Data Swap parameter to Byte, Word or Both. These parameters change the order of the data so that it is compat ible with the wa y the de vice hand les the data in its memo ry. It is best to change the data order in the device being used, but if that is not possible, Data Swap is the best alternative.

5.4 iQube2 Scale

This system has a scale connected to the 1280 using an iQube2 junction box. The setup for this system can be found in the iQube2 technical manual (PN 67888).

To enter the setup mode via the 1280:

1. Press to enter the communications menu. .

Select iQube2 as the Input Type of the connected communications port.

3. Press to enter the Scales menu.

4. Select the iQube2 as the scale kind for the desired scale number. See Section 4.1 on page 57.

5. Press iQube2 setup to enter the iQube2 setup mode.

6. A popup asking Enter iQube2 setup mode displays.

7. Press to enter the iQube2 setup mode.

8. Refer to the iQube2 manual (PN 67888) for setu p information.

Page 84

1280 Series Color Touchscreen Indicator

6.0 Features

The Features menu allows the setup of parameters for the menu items listed inTable 6-1. From the Configuration menu, select the

Features icon (circled in Figure 6-1) to enter the Features menu.

Once all parameters have been set, press to return to weigh mode.

Figure 6-1. Features Menu

Item No. Parameter Description

Softkeys Softkeys setup. See Section 6.1 on page 79.

General Setup general indicator settings. See Section 6.2 on page 81.

Regulatory Allows for the selection of the regulatory mode required for the scale. See Section 6.3 on page 82.

Passwords Allows passwords to be set to secure menus. See Section 6.4 on page 85.

Locale Allows the local language, time/date and decimal format to be setup. See Section 6.5 on page 85.

Contact Info Allows the input of company information. See Section 6.6 on page 86.

Advanced Printing Setup printing using optional printers over network/USB. See Section 6.7 on page 87.

View Alibi Storage Shows past transactions and allows them to be reprinted. See Section 6.8 on page 87.

Table 6-1. Features Menu Parameters

78 Visit our website www.RiceLake.com

Page 85

Features

Enabled softkeys

Enable softkey

Rename softkey User Defined only

Disable softkey

Move softkeys UP/DOWN

6.1 Softkeys

Softkeys are available to provide additional operator func tions for specific applications. When enabled they are displayed as digital buttons at the bottom of the display in weigh mode. Press a softkey to use the assigned functions.

To enter the Softkey menu, press the When the Auto-Pop

ulate Softkey is set to on, the default or the last set softkeys display. See Section 6.1.2.

Features icon . From the Features menu, select Softkeys.

6.1.1 Enable/Disable Softkeys

1. In the Softkey menu, press to bring up the list of predefined softkeys. See Section 6.1.2.

2. Select from the list of predefined softkeys or one of the user defined options.

3. Select to enable the softkey or press cancel to quit.

Figure 6-2. Enable/Disable Softkeys

6.1.2 Predefined Softkeys

Example Softkeys

Batch Start Batch Stop Stops an active batch and turns off all associated digital outputs. Requires a Batch Start to resume processing.

Batch Pause

Batch Reset

Select Scale Diagnostics Opens the iQube2 diagnostics screen

Alibi Allows previous print transactions to be recalled and reprinted. Contrast Adjusts the screen backlight intensity.

Softkey Description

Enter the scale number (using the numeric keypad) to be displayed for multi-scale applications, followed by the select scale softkey.

Table 6-2. Configurable Softkeys

Page 86

1280 Series Color Touchscreen Indicator

Note

Figure 6-3. Database Screen in

Weigh Mode

Figure 6-4. LaserLight Softkey Example

Softkey Description

Test Not available in version 1.00. Stop Sends AuxFmt13 out its configured port to display a red light on a LaserLight. Go Sends AuxFmt12 out its configured port to display a green light on a LaserLight. Off Sends AuxFmt14 out its configured port to turn a LaserLight red/green light off. Display Unit ID Displays the Unit ID in the lower left corner of the screen. Zero Zeros the indicator. Gross/Net Toggles between gross and net modes. Tare Tare the scale by using the onscreen numeric keypad Keyed Tare Tare the scale by using the onscreen numeric keypad Units Toggles between primary, secondary and tertiary units. Print Prints the configured print format. Aux Print Auxilliary printing by entering the Auxilary Format number (1-20) using onscreen numeric keypad Screen Display a different screen by entering a value (1-99) and pressing the Screen softkey. Database Accesses the import and export database feature from the weigh mode.

Table 6-2. Configurable Softkeys (Continued)

The Zero, Gross/Net, Tare, Units and Print softkeys are functionally equivalent to the keypad function keys. These softkeys are primarily for web browser remote connections, when a physical keypad is not available.

6.1.3 Database Softkey

User must configure the Database softkey to use the Database Import/Export functionality from weigh mode.

To access the database import or export features from the weigh mode:

1. Press the

2. Select either

Database softkey. The database menu will display for several seconds.

Import Database or Export Database. The Import/Export screen will

display.  See Section 13.3 on page 122 or Section 13.5 on page 123 to complete the database import/export.

6.1.4 LaserLight Softkey

User must configure 1280 softkeys to use Stop/Go. See Table 6-3 to view the pre-populated commands in the print formats.

Table 6-3 lists commands to display the Stop, Go (circle or arrow) and Off elements on a LaserLight. The command information

can be changed. The softkey is coded to send the associated AuxFmt.

Serial

Traffic Light State AuxFmt

Stop AuxFmt13 |00DO3! Green Circle AuxFmt12 |00DO2! Green Arrow AuxFmt12 |00DO1! Off AuxFmt14 |00DO0!

Table 6-3. LaserLight2 Commands

Command

80 Visit our website www.RiceLake.com

Page 87

6.2 General Parameters

Note

To enter the General menu, press . From the Features menu, select General.

1. Press the parameter to be set.

Features

2. If the

Unit Id

Consecutive Number

Consecutive Number Start

Full Keyboard Lock Off Locks entire keyboard if turned on. Virtual Keypad Lock Zero Enabled Keyboard Lock Off Locks keyboard except zero key if turned on. Auto-Populate Softkeys

Locale/Remote Server Address

setting needs data entry, a keypad will appear. Enter data and press .

Parameter Default Description

1 Specifies the unit identification number with an alphanumeric value (up to eight charac-

ters).

0 Value is incremented following each print operation that includes <CN> in the ticket for-

mat. When reset, it is set to a value specified in the Consecutive Numbering Start parameter (up to seven characters).

0 Start value of the next print when it is reset. Range is from 0 to 9999999 (up to seven

characters). Example: If set to 0, the next print will be 1. If set to 47, the next print will be 48.

Off When off, the virtual on-screen keypad closes when any of the buttons is activated auto-

matically. When on, the keypad remains in place, but can be closed manually.

Off When on, all screens are automatically populated with softkeys at the bottom of the

screen. When off, the user can place a softkey widget anywhere on the screen.

127.0.0.1 Specifies the IP address of the remote indicator to show on the display. To display the local indicator, set to the localhost address of 127.0.0.1. If a local/remote application, set this parameter, on the remote indicator only, to the IP address of the local indicator to use its display.

Table 6-4. General Parameters Menu

6.2.1 Local/Remote Operation

Local/remote support provides a function equivalent to that of an indicator via web server with network access. The display on the local indicator is also displayed at the remote unit, and keypad input from the remote unit is treated the same as keypad input on the local indicator.

1. Connect both indicators to the same Ethernet TCP/IP or Wi-Fi network.

2. Look up the local indicator’s IP address by pressing the Wi-Fi symb ol in Weigh mode (to bring up the Network Information screen), or look it up under the Communications menu in Configuration mode.

3. On the remote indicator, use the Features/General menu to change the Local/Remote Server Address to the IP address of the local indicator.

4. When in weigh mode, the remote will display a copy of the local indicator's display. Key presses on the remote indicator are passed back to the local to perfo rm their intended function.

•It is recommended to use static IP addresses (set DHCP to Off) when using the local/remote feature, to avoid connection issues.

• For an indicator to show its own display, the Local/Remote Server Address must be set to 127.0.0.1. The display is treated as a

remote if any other IP address is entered.

• If the configuration switch is pr essed on the remote indicator, the remotes configuration menu is shown on the remote on ly. If the

configuration switch is pressed on the local indicator, the locals configuration menu is shown on both indicators.

• If the local indicator goes off-line, the remote indicator’s display is blank, or has dashes for the weight.

• The remote indicator can only display the local’s display and return key/virtual keypad presses. Weight data is not available at

the remote indicator for functions such as printing, serial data streaming or setpoints.

Page 88

1280 Series Color Touchscreen Indicator

Using an Internet Browser as a Remote Display

A virtual display can be viewed on a computer or mobile device using an Intern et browser that supports HTML 5 a nd Javascript, such as Internet Explorer v10 and newer, Chrome v30 and newer or Firefox v32 and newer. In addition to viewing, virtual keypad elements can be activated by clicking on them in the browser window.

80 a

To use this feature, the 12

nd computer/mobile device must be connected to the same network. In the browser’s address

bar (URL), type the 1280’s IP address, using TCP port 3000. Example: If the 1280's

IP address is 192.168.0.1, then navigate the browser to http://192.168.0.1:3000.

6.3 Regulatory

Specifies the regulatory agency having jurisdiction over the scale site. Regulatory agencies regulate legal metrology procedures for each country’s scale performance.

s t

The selection made for this parameter affect also configurable when the Regulatory mode is set to Industrial to accommodate operations that may not be covered specifically by the general regulatory selections.

1. Press the Features icon , then press Regulatory.

2. Press Regulatory Mode. The options menu displays.

3. Select the required mode.

4. Press .

he function of the front panel Tare and Zero keys. Tare and Zero key functions are

Parameter Description

National Type Evaluation Program (NTEP) NTEP is a regulatory agency that serves most of the United States. International Organization of Legal Metrology (OIML) Measurement Canada Measurement Canada is a regulatory agency that serves Canada.

Industrial Mode Industrial Mode is used for non-Legal for Trade applications. See Table 6-8. None A regulatory mode has not been chosen.

Table 6-5. Regulatory Mode Options Menu

OIML is a global intergovernmental organization that publishes legal metrology recommendations for the regulatory agencies of its members.

82 Visit our website www.RiceLake.com

Page 89

6.3.1 Parameters Available in all Regulatory Modes

Parameters Default Description

Alibi Storage Off Allows previous print transactions to be recalled and reprinted if enabled.

Off Scales must be re-calibrated after changing from Off to On. Specifying the latitude

Gravity Compensation

Origin Latitude

Origin Elevation (meters)

Destination Latitude

Destination Elevation (meters)

Monorail Mode

Enable Screen Saver

Screen Saver Weight Threshold

Screen Saver Activation Time

45 Origin latitude of the scale site in degrees, range 0-90 (only available with Gravity

345 Origin Elevation of the scale site in meters, range -9999 to 9999 (only available with

45 Destination latitude of the scale site in degrees, range 0-90 (only available with Grav-

345 Destination Elevation of the scale site in meters, range -9999 to 9999 (only available

Off Allows preset (keyed) tare values to be of higher precision then the display division

Off Enables screen saver functionality. Screen saver can be triggered by the Screen

30 Time at standstil at which the screensaver activates (only available when Enable

and elevation of the calibration and scale sites provides compensation for gravitational effects. To calibrate with gravity compensation, Origin Latitude and Elevation and Destination Latitude and Elevation must be set.

Compensation set to on).

Gravity Compensation set to on).

ity Compensation set to on).

with Gravity Compensation set to on).

size in Monorail applications. Available in future release.

Saver Weight Threshold or the Screen Saver Activation Time. When the screen saver is triggered, the backlight dims to 10%.

0 The screen saver activates when the weight dips below the Screen Saver Weight

Threshold (only available when Enable Screen Saver is set to on).

Screen Saver is set to on).

Features

Table 6-6. Regulatory Mode Parameters – All Modes

Table 6-7 describes the function of TARE and ZERO for the NTEP, CANADA, OIML, and NONE regulatory modes.

Regulatory

Parameter Value

NTEP

OIML

Measurement Canada

Industrial Mode See Table 6-8

Weight on Scale Tare in System

zero or negative

positive

zero or negative

positive

zero or negative

positive

Table 6-7. Tare/Zero Key Functions for Regulatory Parameter Settings

Tare Zero

no no action yes Clear Tare no Tare yes Tare no no action Zero yes Clear Tare Zero and Clear Tare no Tare Zero

yes Tare no no action

yes Clear Tare no Tare yes no action

Front Panel Key Function

Zero

Zero and Clear Tare if weight is within ZRANGE.

No action if weight is outside of ZRANGE

Zero

Page 90

1280 Series Color Touchscreen Indicator

Regulatory

Parameter Value

NONE

Weight on Scale Tare in System

zero or negative

positive

Table 6-7. Tare/Zero Key Functions for Regulatory Parameter Settings (Continued)

no Tare yes Clear Tare no Tare yes Clear Tare

Tare Zero

Front Panel Key Function

Zero

Industrial Mode Parameters

Industrial mode provides a set of sub-parameters to allow customizatio n of tare, clear and print functions in n on-Legal for Trade scale installations.

Parameter Default Description

Audit Agency

Weight Source for Print

Allow Tare in Display Hold Allow Print in Display Hold Off A demand print may be performed while the scale display is being held. Remove Tare on Zero Always Allow Keyed Tare On Preset (keyed) tares will be allowed at any weight, not just at zero gross.

Multiple Tare Action

Allow Negative Tare Allow CLR key to clear tare/accu-

mulator Clear Source Scales Individually Allow Total Scale to Display Nega-

tive Allow Print in Motion Off Allows a demand print to be performed while the scale is in motion.

Allow PT to Keyed Tare Print

Zero Base for Overload

Use Fine Push-Button Tare

Use Fine Keyed Tare

NTEP Defines how the Audit Trail data is displayed/printed, depending on the require-

ments for the various regulatory agencies.

Synchronized to

Display

Off A semiautomatic (push-button) tare that can be taken while the scale display is

Off A tare will be removed if a semiautomatic (push-button) zero is performed on the

Replace Defines the resulting action if a semiautomatic (push-button) tare is attempted while

Off Allows a semiautomatic (push-button) tare to be taken at a negative gross weight,

On Allows the Clear key to clear the tare or accumulator while the tare or accumulator

Off Allows the clearing of tare values from source scales individually when a total scale

Off Allows the total scale to display a negative value, otherwise the total scale will dis-

Off The letters PT will appear on printed output if the tare value is a preset or keyed

Calibrated Zero Used to determine the point at which the scale will display overload, either (cali-

Off When a semiautomatic (push-button) tare is taken, use internal counts instead of

Off When a preset, or keyed tare is entered, use the exact value entered instead of

Synchronized to the displayed value or the scale internal value.

being held.

scale.

there is already a tare for the scale.

• Replace - replaces the current tare with the new one.

• Remove - clears the current tare.

• No Action - rejects the new tare attempt (the current tare must be cleared

before a new tare can be acquired).

resulting in a negative tare weight.

is being displayed.

is involved.

play an error whenever any source scale is displaying a negative value.

tare.

brated zero + capacity + overload setting), or (current captured zero + capacity + overload setting).

the rounded display value.

rounding the value to the current display division.

Tare in Motion Off Allow a semiautomatic (push-button) tare to be taken while the scale is in motion.

Table 6-8. Industrial Mode Parameters

84 Visit our website www.RiceLake.com

Page 91

Parameter Default Description

Zero in Motion

Underload Limit (Display Divisions) Allow Manual Clear Tare On Allows the clearing of the tare value manually at any gross weight. Auto-Zero Tracking on Net Zero Total Scale Requires Identical

Source Count-By

Off Allow a semiautomatic (push-button) zero to be performed while the scale is in

motion.

9999999 Defines the number of display divisions below gross zero that will be displayed

before the scale shows an underload condition.

Off Allows the scale zero to be automatically adjusted, within the specified zero range,

to track a net zero display.

Off Allows source scales, when a total scale is involved, to have different display divi-

sion sizes.

Table 6-8. Industrial Mode Parameters (Continued)

6.4 Passwords

Passwords can be set to secure the Configuration, Setpoints an d Calibration menus.

1. Ensure the audit jumper (JP1) is in the On po

sition in order to turn on the passwords. See Figure 3-3 on page 54.

Features

2. Press the

Features icon , the press Passwords.

3. Select the Configuration, Setpoints or Calibration. The keyboard displays.

4. Enter the password, then press .

Parameters Parameter

Configuration Password

Setpoints Password

Calibration Password

Allows the configuration parameters to be accessed without the need to press the configuration button. Allows the Enable and Value setpoint parameters to be accessed without the need to press the configuratio n but-

ton. Allows the calibration parameters to be accessed without the need to press the configuration button.

Table 6-9. Menu Passwords

6.5 Locale

Select this parameter to set the desired language, date and time formats, and decimal format.

1. Press , then press Locale.

2. Press the parameter to set.

3. Select the setting desired.

4. Press .

Parameter Default Description

Default Weigh Mode Language

Date Format MMDDYYYY Date Separator Slash (/) Select one of three date separators available, Slash (/), Dash (-), Semi-colon (;).

Time Format 12 Hour Select 12 hour or 24 hour time format. Time Separator Colon (:) Select Colon (:) or Comma (,) as the time separator. Decimal Format Dot (.) Select Dot (.) or Comma (,) as the format for the decimal.

English

Select from 16 languages available for the indicator weigh mode. See Section 6.5.1. Indicator must be rebooted for change to take affect.

Select one of the four formats available: MMDDYYYY, DDMMYYYY, YYYYMMDD, YYYYDDMM.

Table 6-10. Locale Parameters Menu

Page 92

1280 Series Color Touchscreen Indicator

•English

• Spanish

•French

• Portuguese

• Italian

• German

•Dutch

•Danish

•Swedish

• Russian

• Ukrainian

•Hebrew

•Arabic

•Thai

• Chinese

• Turkish

Parameter Default Description

Time/Date Change Restriction

Off

Returns current status, only works in setup mode ON/OFF

Table 6-10. Locale Parameters Menu (Continued)

6.5.1 Default Weigh Mode Languages

There are 16 languages available for the indicator weigh mode.

6.6 Contact Info

Enter the Contact Info menu to setup company information. Press , select Contact Info

1. Press the parameter to be set. A keyboard will display.

2. Enter the information and press .

3. Repeat steps 1 and 2 until all desired entries have been made.

Parameter Description

Company Name Enter the company name (up to 30 characters). Address Line 1-3 Enter the address, three lines available (up to 30 characters per line). Contact Name 1-3 Enter up to three contact names (up to 20 characters per contact). Contact Phone 1-3 Enter up to three contact phone Numbers (up to 20 characters per phone number). Email Address Enter an email address (up to 30 characters). Next Calibration Date Specify the next calibration date. Last Calibration Date Specify the last calibration date.

Table 6-11. Contact Info Parameters

86 Visit our website www.RiceLake.com

Page 93

6.7 Advanced Printing

Note

Allows printing from network/USB sources or by using iR ite.

Enabling USB and advanced printing simultaneously is now supported. This is useful if both local and network printers are used.

Figure 6-5. Advanced Printer Setup Menu

1. Press to enter the printer setup wizard.

Features

2. Select the manufacturer of the printer from the list. Use the scroll bar to view all selections. With the manufacturer selected, press .

3. Using the same process as step 2, select the Model of the printer.

4. Select the connection type to be used to connect to the printer, network or USB.

5. If using a network connection, enter the Network URl.

The 1280 supports Direct Print and Internet Printing Protocol for printing directly to a printer. URI examples include:

socket://<ip-address-of printer>:9100 ipp://<ip-address-of-printer>:631

6. Press to complete the setup. Printer successful installed displays.

6.8 View Alibi Storage

Allows previous print transactions to be recalled and reprinted. Approximately 500,000 alibi messages can be stored. Set the Alibi Storage to On b

1. Press , select View Alib

2. Use the arrows to scroll to the record needed. Alternatively, enter the date range to search for the record.

3. Select the desired record.

4. To print the currently selected record, press

5. Repeat steps 1-4 until all records required have been printed.

y entering the regulatory menu under features. See Section 6.3.1 on page 83.

i Storage.

Reprint.

6. When all records required have been printed, press .

A demand print string is stored in Alibi memory and is assigned an ID number. The token <AN> for the Alibi ID number should be added to the print strings for reference. The

Some data is dependent upon the ti

cket format, see Section 7.0 on page 89 to format a ticket to contain the tokens for weight,

print string is stored with a Checksum to ensure data integrity.

date and time, scale number, alibi ID.

Page 94

1280 Series Color Touchscreen Indicator

1 2 3 4 5

6 7 8

Checksum

The checksum is calculated when the weighment is stored in alibi storage. Wh en the data is retrieved, the checksum is recalibrated and compared to the initial value. If the values match, the data is transmitted. If they do not match, the 1280 will send an Invalid Record response.

The checksum is for internal use only and not retrievable, since all data is stored internally. External Alibi storage is not

orted.

Figure 6-6. Alibi Storage Screen

Item No Parameter

Records – number of records.

Page to beginning.

Page left or right.

Page to the end.

Search by date.

Selected Id for current record.

Reprint current record.

Done – press to return to previous menu.

Table 6-12. Alibi Storage

88 Visit our website www.RiceLake.com

Page 95

7.0 Formats

The Format menu allows the setup of print and stream formats.

Formats

From the Configuration menu, select the

Formats icon (circled in Figure 7-1) to enter th e Formats menu. Once all

parameters have been set, press to return to weigh mode.

Figure 7-1. Format Menu

Item No. Parameter Description

Print Formats

Stream Formats

3 Selection Field Allows selection of print or stream formats.

Used to se the setpoint push-print or truck weigh-in/weigh-out operations are performed. See Section 7.1

The 1280 s one of nine pre-configured formats (see Table 7-2), or the data frame can be customized.

t the printed output when the Print key is pressed, a KPRINT command is received or when

upports four configurable data streaming formats that can be set to outside data frames in

Table 7-1. Format Menu Parameters

7.1 Print Format

The print format used for a given print operation depends on the indicator configuration and the operation performed. Each print format can be customized to include up to 1000 characters of information, such as company name and address, on printed tickets.

Page 96

1280 Series Color Touchscreen Indicator

Figure 7-2. Select Format

Note

Use the Revolution configuration utility, serial commands or the indicator front panel to customize the print formats.

1. Press , then select

Print Format.

2. Press the selection field arrow (circled in Figure 7-2) to select the print format to be configured. The current settings for that format will appear to the right.

3. Press the format to be edited. The format editor displays. Table 7-4 lists print tokens, which are always enclosed in < >. Characters not enclosed in < > will be printed as displayed.

4. When finished editing the print format, press .

5. Set the communications port destination parameters as needed. See Section 7.1.2.

7.1.1 Default Print Formats

Table 7-2 lists all of the default print formats. These are the formats used when the indicator’s configuration is reset.

Print Format Default Format

Gross Format GROSS<G><NL2><TD><NL> Net Format GROSS<G><NL>TARE<SP><T><NL>NET<SP2><N><NL2><TD><NL> Setpoint Format <SCV><SP><SPM><NL> Header 1 COMPANY NAME<NL>STREET ADDRESS<NL>CITY, ST ZIP<NL2> Header 2 COMPANY NAME<NL>STREET ADDRESS<NL>CITY, ST ZIP<NL2> Accumulator Format ACCUM <A><NL><DA> <TI><NL>

Alert Format Audit Trail Format Not Available

Auxiliary Format 1-20

GROSS<G><NL2><TD><NL>

Note: AuxFmt12, AuxFmt13 and AuxFmt14 are specified for the LaserLight only.

Table 7-2. Default Print Formats

7.1.2 Set Destination 1 and 2 Print Format

Up to two communication ports can be defined to allow the same format to be sent out simultaneously.

1. Press Destination 1

2. Repeat for Destination 2 (optional).

Parameter Description

None A destination has not been set for the print format Basic USB Printer Supports only a single printer that uses only ASCII characters Advanced Printer Supports wide range of commercial printers and languages Serial Port 1 Communications port support RS-232, RS-422 and RS-485 (J6) Serial Port 2 Communications port support RS-232, RS-422 and RS-485 (J7) USB Port (Port 3) Micro USB device port that can be used as a communications port (J5)

Bluetooth TCP Client 1 Specific settings for TCP Client 1 TCP Client 2 Specific settings for TCP Client 2

Base destination list will grow with serial ports 5-16 depending on installed option cards.

and select the serial port to be used.

(Port 4) A wireless communications port using the Bluetooth® standard

Table 7-3. Destination Options

90 Visit our website www.RiceLake.com

Page 97

Formats

7.1.3 Print Format Tokens

Token Description Supported Ticket Formats

General Weight Data Tokens

<G> Gross weight, current scale <G#n> Gross weight, scale n <N> Net weight, current scale <N#n> Net weight, scale n <T> Tare weight, current scale <T#n> Tare weight, scale n <S> Current scale number

Notes: Gross, net, tare, accumulator, truck and setpoint weights can be printed in any configured weight unit by adding the following

modifiers to the gross, net, and tare weight tokens: /P (primary units), /D (displayed units), /S (secondary units) or /T (tertiary units). If not specified, the currently displayed unit (/D) is assumed. Example: To format a ticket to show net weight for Scale 3 in secondary units, use the following token: <N#3/S>

Formatted weight strings contain a 10-digit weight field (including sign and decimal point, with leading zeros suppressed), followed by a space and a two-digit unit identifier. Total field length with units identifier is 13 characters.

Accumulator Tokens

<A> Accumulated weight, current scale <A#n> Accumulated weight, scale n <AA> Average accumulation, current scale <AA#n> Average accumulation, scale n <AC> Number of accumulations, current scale <AC#n> Number of accumulations, scale n <AT> Time of last accumulation, current scale <AT#n> Time of last accumulation, scale n <AD> Date of last accumulation, current scale <AD#n> Date of last accumulation, scale n

Setpoint Tokens

<SCV> Setpoint captured value <SN> Setpoint number <SNA> Setpoint name <SPM> Setpoint mode (gross or net label) <SPV> Setpoint preact value <STV> Setpoint target value

Auditing Tokens

<CD> Last calibration date

<NOW> Number of weighments since last calibration

Note: Last calibration date (<CD>) and number of calibrations (<NOC>) are updated anytime a calibration is performed on any of the scales. Number of weighments (<NOW> token) is incremented whenever the scale weight exceeds 10% of scale capacity. Scale must return to gross or net zero before the value can be incremented again.

Table 7-4. Print Format Tokens

GFMT, NFMT, TRWIN. TRWOUT, ACCFMT, AUXFMTxx,

ALERT

GFMT, NFMT, ACCFMT, AUXFMTxx

SPFMT

All<NOC> Number of calibrations

Page 98

1280 Series Color Touchscreen Indicator

Token Description Supported Ticket Formats

Formatting and General-Purpose Tokens

ASCII character (nnn = decimal value of ASCII character).

<nnn>

Used for inserting control characters (STX, for example) in the

print stream. <TI> Time <DA> Date <TD> Time and date <UID> Unit ID number (up to 8 alphanumeric characters) <CN> Consecutive number (up to 7 digits) <H1> Insert header format 1 (HDRFMT1); see Table 7-2 on page 90

All

<H2> Insert header format 2 (HDRFMT2); see Table 7-2 on page 90 <CR> Carriage return character <LF> Line feed character

<NLnn>

New line (nn = number of termination (<CR/LF> or <CR>)

characters)* <SPnn> Space (nn = number of spaces)* <SU> Toggle weight data format (formatted/unformatted)

Note: If nn is not specified, 1 is assumed. Value must be in the range 1–99.

User Program-dependent Tokens

<USnn>

Insert user print text string (from user program, SetPrintText

API)

All

<EVx> Invoke user program print handler x (PrintFmtx)AUXFMTx <AN> Enables the addition of an Allibi ticket number. All Alert Format Tokens <COMP> Company name (up to 30 characters) <COAR1>

<COAR2>

Contact company address, lines 1–3 (up to 30 characters) <COAR3>

Contact names (up to 20 characters)

All

<COPH2>

Contact phone numbers (up to 20 characters) <COPH3>

<COML> Contact e-mail address (up to 30 characters) <ERR> Alert error message (system-generated) ALERT

Table 7-4. Print Format Tokens (Continued)

92 Visit our website www.RiceLake.com

Page 99

7.2 Strteam Format Menu

The four stream formats can each be sent out of one or more of the indicator's communications ports.

Parameters Default Description

Off Select Legal for Trade (stream data updates at the display update rate), Industrial

Output Stream Type

Stream Source None The scale the weight data will be taken from. Stream Destinations

Stream Format

Custom Format

Gross Token

Tare Token

Net Token

Positive Token

Negative Token

Primary Token

Secondary Token

Tertiary Token

Zero Token

Motion Token

Range Token

OK Token

Invalid Token

<2><P><W7.><U><M><S> Used to define a custom stream frame format, if the stream format parameter is

None Defines the communication ports the stream data will be sent to (more than one

RLWS/Condec Specifies the format of the stream frame. Select one of the four available default

G Defines what will be sent in the data frame for the Mode Token when in Gross

T Defines what will be sent in the data frame for the Mode Token when in Tare

N Defines what will be sent in the data frame for the Mode Token when in Net mode

Space From a list, select the character that will be sent in the data frame for the Polarity

Minus Defines the character that will be sent in the data frame for the Polarity Token

L Defines what will be sent in the data frame for the Units Token when displaying

K Defines what will be sent in the data frame for the Units Token when displaying

Z Defines what will be sent in the data frame for the Status Token when weight is at

M Defines what will be sent in the data frame for the Status Token when weight is in

O Defines what will be sent in the data frame for the Status Token when weight is

[blank entry] Defines what will be sent in the data frame for the Status Token when weight is

I Defines what will be sent in the data frame for the Status Token when weight is

(stream data updates at up to the scale sample rate) or Off (disables the stream format). If Legal for Trade or Industrial is selected, the parameters Stream Source and Stream Destinations display.

can be selected).

formats, or select custom and use the Custom Format parameter to build a stream frame. If Custom is selected, the following parameters (in blue) display.

set to custom.

mode (up to eight characters).

(up to eight characters).

Token when displaying a positive weight. The default is a blank space.

when displaying a negative weight.

Primary units (up to eight characters).

Secondary units (up to eight characters).

Tertiary units (up to eight characters).

Center of Zero (up to two characters).

Motion (up to two characters).

Out of Range (up to two characters).

OK (or not in one of the other states) (up to two characters). The default is a blank space.

Invalid (up to two characters).

Formats

Table 7-5. Stream Format Parameters

Stream Format

To set up the stream formats using the indicator front panel:

1. Press , then select Stream Format. See Figure 7-1.

2. Press to select the format to be configured.

Page 100

1280 Series Color Touchscreen Indicator

3. Press Output Stream Type to set Industrial or Legal for Trade.

4. Press .

5. Press Stream Source to set one of the eight scales for the format.

6. Press Stream Format to choose the format to be used and press .

7. If Custom Format was selected in step 6, press select Custom Format. The Custom Format keypad will display. Stream tokens are listed in Table 7-6. Press .

8. Press Stream Destinations to indicate where to stream.

9. Press .

10. Set the values for the Stream Tokens (See Table 7-5) as needed.

94 Visit our website www.RiceLake.com