RHYNO RWC-50 Operator's Manual

[1]

RHYNO 18V 1/2” Impact Wrench

-OPERATOR’S MANUAL - USA

TO REDUCE THE RISK OF INJURY, USERS MUST READ AND UNDERSTAND
OPERATOR’S MANUAL.

Rev A 4/1/2017

Catalog No: RWC

-50

[2]

WARNING! Read all safety warnings

and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.

WARNING! To reduce the risk of

injury, read the instruction manual

If you have any questions or comments
about this or any RHYNO tool, call us toll
free at:

844-25RHYNO (844-257-4966)

RHYNO Windshield Cutter™ is a
Trademark of EnTheos Design Solutions,
LLC.

All rights reserved. Copyright 2017©

SYMBOLOGY

V ………………Volts
Hz ……………. Hertz
C ……………… Celcius
F ……………… Fahrenheit
AWG ……….. American Wire Gage
LED ………….. Light Emitting Diode
min …………. minutes
/min ……….. Per minute
bpm ………. Beats/min
ipm …………. Inches/min
RPM ………… rotations/min
sfpm ………. Surface feet/min
SPM ……….. Strokes/min
A ……………. Amperes
W …………… Watts
AC ………….. Alternating Current
DC ………….. Direct Current

……… Wear eye protection

……… Wear hearing protection

……… Wear respiratory protection

........ safety alert symbol

……… Read Manual

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please
read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided,

may result in property damage.

NOTICE: Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.

[3]

Variable Speed

Trigger Switch

Work Light

Battery Release

Button

Forward

-

Reverse

Button

Anvil

Handle

Battery

Pack

Fuel Gage

Belt Clip

[4]

GENERAL POWER TOOL SAFETY
WARNINGS

WARNING! To reduce the risk of

injury, read the instruction manual.

WARNING! Read all safety warnings

and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and /or serious injury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings
refers to your mains-operated (corded) or
battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust.

Power tools create sparks which may
ignite the dust or fumes.

c)

Keep children and bystanders away

while operating a power tool.

Distractions can cause you to lose
control.

2) ELECTRICAL SAFETY

a)

Power tool plugs must match the

outlet. Never modify the plug in any
way. Do not use any adapter plugs with
earthed (grounded) power tools.

Unmodified plugs and matching outlets
will reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,
radiators, ranges and refrigerators.

There is an increased risk of electric
shock if your body is earthed or
grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power
tool will increase the risk of electric
shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase
the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for
outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric
shock.

f)

If operating the power tool in damp

locations is unavoidable, use a Ground
Fault Circuit Interrupter (GFCI)

1 Housing

18Star Screw

2

2 Screw

49Reversing Lever

1

3 Gear Box

110Switch

1

4 Stator

111Belt Hook

1

5 Rotor 1 12 Star Screw 8

6 Endbell Plate 1 13 Battery Pack 2

7 Back Cover 1 14 Charger 1

Qty.No. Part Name Qty. No. Part Name

[5]

protected supply. Use of a GFCI reduces
the risk of electric shock.

3) PERSONAL SAFETY
a) Stay alert, watch what you are doing

and use common sense when
operating a power tool. Do not use a
power tool while you are tired or under
the influence of drugs, alcohol or
medication. A moment of inattention

while operating power tools may result
in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection.
Protective equipment such as safety
glasses, dust mask, protective gloves or
hearing protection used for appropriate
conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your

finger on the switch or energizing the
power tools that have the switch on
invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A
wrench or a key left attached to a
rotating part of the power tool may
result in personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables
better control of the power tool in
unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long

hair can be caught in moving parts.

g) If devices are provided for the

connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of

dust collection can reduce dust-related
hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job
better and safer at the rate for which it
was designed.

b) Do not use the power tool if the switch

does not turn on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.

c) Disconnect the plug from the power

source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive

safety measures reduce the risk of
starting the power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.

Power tools are dangerous in the hands
of untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many

accidents are caused by poorly
maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.

g) Use the power tool, accessories and

tool bits, etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for

operations different from those
intended could result in a hazardous
situation.

5) BATTERY TOOL USE AND CARE

a)

Recharge only with the charger

specified by the manufacturer. A

[6]

charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects like
paper clips, coins, keys, nails, screws,
or other small metal objects that can
make a connection from one terminal
to another. Shorting the battery

terminals together may cause burns or
a fire.

d) Under abusive conditions, liquid may

be ejected from the battery; avoid
contact. If contact accidentally occurs,
flush with water. If liquid contacts
eyes, additionally seek medical help.

Liquid ejected from the battery may
cause irritation or burns.

6) SERVICE

a)

Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will

ensure that the safety of the power tool
is maintained.

Safety Warnings for Impact
Wrenches/Drivers

• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory

contacting a “live” wire may make
exposed metal parts of the power tool
“live” and could give the operator an
electric shock.

• Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by

hand or against your body is unstable and
may lead to loss of control.

• Wear safety goggles or other eye
protection. Hammering and drilling

operations cause chips to fly. Flying
particles can cause permanent eye
damage.

• Always use the side handle supplied with
the tool. Keep a firm grip on the tool at
all times. Do not attempt to operate this
tool without holding it with both hands.

Operating this tool with one hand will
result in loss of control. Breaking through
or encountering hard materials such as
re-bar may be hazardous as well.

• Accessories and tool may get hot during
operation. Wear gloves when handling

them.

• Do not operate this tool for long periods
of time. Vibration caused by hammer

action may be harmful to your hands and
arms. Use gloves to provide extra cushion
and limit exposure by taking frequent rest
periods.

• Air vents often cover moving parts and
should be avoided. Loose clothes, jewelry

or long hair can be caught in moving
parts.

WARNING! ALWAYS use safety

glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting
operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA

Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory

protection.

WARNING! Some dust created by

power sanding, sawing, grinding, drilling,
and other construction activities contains
chemicals known to the State of California
to cause cancer, birth defects or other

[7]

reproductive harm. Some examples of these
chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement

and other masonry products

• arsenic and chromium from chemically-
treated lumber.

Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.

• Avoid prolonged contact with dust from
power sanding, sawing, grinding, drilling,
and other construction activities. Wear
protective clothing and wash exposed
areas with soap and water. Allowing dust

to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful
chemicals.

WARNING! Use of this tool can generate

and/or disperse dust, which may cause
serious and permanent respiratory or other
injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the
dust exposure. Direct particles away from
face and body.

WARNING! Always wear proper
personal hearing protection that conforms
to ANSI S12.6 (S3.19) during use. Under

some conditions and duration of use, noise
from this product may contribute to hearing
loss.

CAUTION: When not in use, place tool
on its side on a stable surface where it will
not cause a tripping or falling hazard. Some

tools with large battery packs will stand

upright on the battery pack but may be
easily knocked over.

BATTERY PACKS AND CHARGERS

The battery pack is not fully charged out of
the package. Before using the battery pack
and charger, read the safety instructions
below and then follow charging procedures
outlined. When ordering replacement
battery packs, be sure to include the catalog
number and voltage. Your tool uses a
RHYNO charger. Be sure to read all safety
instructions before using your charger.
Consult the chart at the end of this manual
for compatibility of chargers and battery
packs.

READ ALL INSTRUCTIONS

Important Safety Instructions for All
Battery Packs

WARNING! Read all safety warnings
and all instructions for the battery pack,
charger and power tool. Failure to follow
the warnings and instructions may result in
electric shock, fire and/or serious injury.

• Do not charge or use the battery pack in

explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery

pack from the charger may ignite the dust
or fumes.

• NEVER force the battery pack into the

charger. DO NOT modify the battery pack
in any way to fit into a non-compatible
charger as battery pack may rupture
causing serious personal injury. Consult

the chart at the top of page 3 for
compatibility of battery packs and
chargers.

• Charge the battery packs only in

designated RHYNO chargers.

• DO NOT splash or immerse in water or

other liquids.

• Do not store or use the tool and battery

pack in locations where temperatures

[8]

may reach or exceed 104°F (40°C) (such
as outside sheds or metal buildings in
summer. For best life, store battery pack

in a cool, dry location.
NOTE: Do not store the battery packs in a
tool with the trigger switch locked on.
Never tape the trigger switch in the ON
position.

• Do not incinerate the batter pack even if

it is severely damaged or is completely

worn out. The battery pack can explode

in a fire. Toxic fumes and materials are

created when lithium ion battery packs

are burned.

• If battery contents come into contact

with the skin, immediately wash area

with mild soap and water. If battery

liquid gets into the eye, rinse water over

the open eye for 15 minutes or until

irritation ceases. If medical attention is

needed the battery electrolyte is

composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may

cause respiratory irritation. Provide

fresh air. If symptoms persist, seek

medical attention.

WARNING! Burn hazard. Battery liquid

may be flammable if exposed to spark or
flame.

WARNING! Fire hazard. Never attempt

to open the battery pack or any reason. If
the battery pack case is cracked or
damaged, do not insert into the charger. Do
not crush, drop or damage the battery pack.
Do not use a battery pack or charger that
has received a sharp blow, been dropped,
run over or damaged in any way (e.g.,
pierced with nail, hit with a hammer,
stepped on). Damaged battery packs
should be returned to the service center for
recycling.

Transportation

WARNING! Fire hazard. Do not store
or carry the battery pack so that metal
objects can contact exposed battery
terminals. For example, do not place the

batter pack in aprons, pockets, tool boxes,
product kit boxes, drawers, etc., with loose
nails, screws, keys, etc.

WARNING! Transporting battery packs
can possibly cause fires if the battery
terminals inadvertently come into contact
with conductive materials such as keys,
coins, hand tools, etc. The US Department

of Transportation Hazardous Material
Regulations (HMR) actually prohibit
transporting battery packs in commerce or
on airplanes in carry-on baggage UNLESS
they are properly protected from sort
circuits. So when transporting individual
battery packs, make sure that the battery
terminals are protected and well insulated
from materials that could contact them and
cause a short circuit.

Fuel Gage Battery Packs

RHYNO Battery Packs or tools include a fuel
gage which consists of three green LED
lights that indicate the level of charge
remaining in the battery pack.
The fuel gage is an indication of
approximate levels of charge remaining in
the battery pack according to the following
indicators:

[9]

To actuate the fuel gage, press and hold the
fuel gage button. A combination of three
green LED lights will illuminate designating
the level of charge left. When the level of
charge in the battery pack is below the
usable limit, the fuel gage will not illuminate
and the battery pack will need to be
recharged.

NOTE: The fuel gage is only an indication of
the charge left on the battery pack. It does
not indicate tool functionality and is subject
to variation based on product components,
temperature and end-user application.

Important Safety Instructions for
All Battery Chargers

WARNING! Read all safety warnings

and all instructions for the battery pack,
charger and power tool. Failure to follow
the warnings and instructions may result in
electric shock, fire and/or serious injury.

• DO NOT attempt to charge the battery
pack with any charges other than the
ones in this manual. The charger and

battery pack are specifically designed to
work together.

• These chargers are not intended for any
uses other than charging RHYNO
rechargeable battery packs. Any other

uses may result in risk of fire, shock, or
electrocution.

• Do not expose the charger to rain or
snow.

• Pull by the plug rather than the cord
when disconnecting the charger. This

will reduce the risk of damage to the
electric plug and cord.

• Make sure that the cord is located so that
it will not be stepped on, tripped over or
otherwise subjected to damage or stress.

• Do not use an extension cord unless it is
absolutely necessary. Use of a cord

suitable for outdoor use reduces the risk
of electric shock.

• An extension cord must have adequate
wire size or AWG for safety. The smaller

the gage number of the wire, the greater
the capacity of the cable, that is, 16 gage
has more capacity than 18 gage. An
undersized cord will cause a drop in line
voltage resulting in loss of power and
overheating. When using more than one
extension to make up the total length, be
sure each individual extension contains at
least the minimum wire size. The
following table shows the correct size to
use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The lower the
gage number, the heavier the cord.

• Do not place any object on top of the
charger or place the charger on a soft
surface that might block the ventilation
slots and result in excessive internal

25 (7.6) 50 (15.2)

100 (30.5)

150 (45.7)

50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More
Than

Not More

Than

0 6 18 16 16 14

6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not recommended

Minimum Gage for Cord Sets

Volts

120V

220V

Total Length of Cord in Feet (meters)

American Wire Gage

[10]

heat. Place the charger in a position away
from any heat source. The charger is
ventilated through slots in the sides of the
housing.

• Do not operate the charger with a
damaged cord or plug.

• Do not operate the charger if it has
received a sharp blow, been dropped or
otherwise damaged in any way. Take it

to an authorized service center.

• Do not disassemble the charger; take it
to an authorized service center when
service or repair is required. Incorrect

reassembly may result in a risk of electric
shock, electrocution or fire.

• Disconnect the charger from outlet
before attempting any cleaning. This
will reduce the risk of electric shock.

Removing the battery pack will not
reduce this risk.

• NEVER attempt to connect 2 chargers
together.

• The charger is designed to operate on
standard 120V/220V household
electrical power. Do not attempt to use
it on any other voltage.

WARNING! Shock hazard. Do not allow

any liquid to get inside the charger. Electric
shock may result.

WARNING! Burn hazard. Do not

submerge the batter pack in any liquid or
allow any liquid to enter the battery pack.
Never attempt to open the battery pack for
any reason. If the plastic housing of the
battery pack breaks or cracks, return to a
service center for recycling.

CAUTION: Burn hazard. To reduce the

risk of injury, charge only RHYNO
rechargeable battery packs. Other types of
battery packs may overheat and burst
resulting in personal injury and property
damage.
NOTICE: Under certain conditions, with the
charger plugged into the power supply, the

charger can be shorted by foreign material.
Foreign material of a conductive nature,
such as, but not limited to, grinding dust,
metal chips, steel wool, aluminum foil or
any buildup of metallic particles should be
kept away from the charger cavities.
Always unplug the charger from the power
supply when there is not battery pack in the
cavity. Unplug the charger before
attempting to clean.

Charging a Battery Pack

NOTICE: To ensure maximum performance

and life of lithium-ion battery packs, charge
the battery pack fully before first use.

1) WHEN TO CHARGE BATTERY PACK

a. The fuel gage on the battery pack

indicates the current battery capacity.
If battery pack is less than 100% or 3
green bars, battery pack can be charged
to full capacity.

b. Remove the battery pack from the tool

for charging when needed. RHYNO
Lithium-ion battery packs do not
develop “memory” when charged after
only a partial discharge. It is not
necessary to run down the battery pack
before placing it on the charger.

c. You can “top off” each battery pack at

any time or at any level of battery
charge as needed.

d. The only time that it is necessary to

charge a battery pack is if it has reached
the end of its charge. To signal the end
of its charge, power to the tool will stop.

2) CHARGING A BATTERY PACK

a. Align the battery pack with the bay and

slide the battery pack into the charger
as far as possible. The red LED will
indicate charging is ongoing.

[11]

b. After inserting the battery pack fully

into the charger slot, the LED will
indicate RED while charging.

c. When charging is complete, the LED will

indicate GREEN.

d. If the battery pack or charger is out of the

normal temperature range of 32°F-113°F
(0°-45°C) the LED will indicate RED &
GREEN.

e. A fully discharged battery pack with an

internal temperature in the normal
range will charge in about 15-20
minutes. Heavily cycled batteries may
take longer to completely charged.

NOTICE: Hot or cold batteries will take
longer to charge.
NOTICE: Inverters or generators rated to
100 watts or higher can be used to power
charger.

3) CLEANING

Clean out dust and debris from charger
vents and electrical contacts by blowing
with compressed air. Use only mild soap
and a damp cloth to clean the battery pack
and charger, keeping away from the
electrical contacts. Certain cleaning agents
and solvents are harmful to plastics and
other insulted parts. Some of these include
gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents,
ammonia and household detergents
containing ammonia. Never use

flammable or combustible solvents around
batteries, charger or tools.

4) REPAIRS

The charger has no serviceable parts.

Hot/Cold Battery Pack Delay

When the charger detects a battery pack
that is too hot or too cold, it automatically
starts a Hot/Cold Pack Delay, suspending
charging until the batty pack has reached an
appropriate temperature. The charger then
automatically switches to the pack charging
mode. This feature ensures maximum
battery pack life.
A cold battery pack will charge at a slower
rate than a warm battery pack. The battery
pack will charge at that slower rate
throughout the entire charging cycle and
will not return to maximum charge rate
even if the battery pack warms.

Lithium-Ion Battery Pack Only

Li-Ion tools are designed with an Electronic
Protection System that will protect the
battery pack against overloading,
overheating or deep discharge. The tool will
automatically turn off if the Electronic
Protection System engages. If this occurs,
place the Li-Ion battery pack on the charger
until it if fully charged.

ASSEMBLY AND ADJUSTMENTS

WARNING! To reduce the risk of
serious personal injury, turn unit off and
remove the battery pack before making
any adjustments or removing /installing
attachments or accessories. An accidental

start-up can cause injury.

Installing and Removing the
Battery Pack

NOTE: For best results, make sure your

battery pack is fully charged.

[12]

To install the battery pack into the tool
handle, align the battery pack with the rails
inside the tool’s handle and slide it into the
handle until the battery pack is firmly
seated in the tool and ensure that it does
not disengage.

To remove the battery pack from the tool,
press the release button and firmly pull
the battery pack out of the tool handle.
Insert it into the charger as described in
the charger section of this manual.

INTENDED USE

DO NOT use under wet conditions or in

presence of flammable liquids or gases.

This impact wrench is a professional power
tool. DO NOT let children come into
contact with the tool. Supervision is
required when inexperienced operators
use this tool.

Variable Speed Trigger Switch

To turn the tool on, squeeze the variable
speed trigger switch. To turn the tool off,
release the trigger switch. Your tool is
equipped with a brake. The chuck will stop
as soon as the trigger switch is fully
released.

NOTE: Continuous use in variable speed
range is not recommended. It may damage
the switch and should be avoided.

Forward/Reverse Control Button

The forward/reverse control button
determines the direction of the tool and
also serves as a lock-off button.

To select forward rotation, release the
trigger switch and depress the
forward/reverse control button on the
right side of the tool.

To select reverse, release the trigger switch
and depress the forward/ reverse control
button on the left side of the tool.

The center position of the control button
locks the tool in the OFF position. When
changing the position of the control
button, be sure the trigger is released.

NOTE: The first time the tool is run after
changing the direction of rotation, you may
hear a click on start up. This is normal and
does not indicate a problem.

Work Light

The work light is located on the foot of the
tool. The work light is activated when the
trigger switch is depressed.

Speed / Torque Control

Speed and torque can be adjusted with the
Indicator Panel at the base of the tool
above the battery pack.

1) Depress the left Indicator Panel button

to display battery fuel gauge

2) Depress the right button on the

Indicator Panel to adjust SLOW,
MEDIUM or FAST speed/torque.

NOTE: Speed/torque settings will be saved
after 3 seconds and stored even after
replacing battery pack.

[13]

Anvil With Detent Pin

WARNING! Use only impact

accessories. Non-impact accessories may
break and cause a hazardous condition.
Inspect accessories prior to use to ensure
that it contains no cracks.

CAUTION! Inspect anvils, detent pins

and hog rings prior to use. Missing or
damaged items should be replaced before
use. Place the switch in the locked off
(center) position or remove battery pack
before changing accessories.

To install an accessory on the anvil, align
the hole in the side of the accessory with
the detent pin (H) on the anvil (C). Press the
accessory on until
the detent pin
engages in the
hole. Depression
of detent pin may
be necessary to
aid installation of
accessory.

Belt Hook

WARNING! To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making
any adjustments or removing/installing

attachments or accessories. An accidental

start-up can cause injury.

WARNING! To reduce the risk of
serious personal injury, ONLY use the
tool's belt hook to hang the tool from a
work belt. DO NOT use the belt hook for

tethering or securing the tool to a person
or object during use. DO NOT suspend tool
overhead or suspend objects from the belt
hook.

WARNING! To reduce the risk of
serious personal injury, ensure the screw

holding the belt hook is secure.

CAUTION: To reduce the risk of
personal injury or damage, DO NOT use
the belt hook to hang the impact wrench
while using as a spotlight.

IMPORTANT: When attaching or replacing

the belt hook or bit clip, use only the screw
that is provided. Be sure to securely tighten
the screw.

The belt hook can be attached to either
side of the tool using only the screw
provided, to accommodate left- or right­handed users. If the hook is not desired at
all, it can be removed from the tool. To
move belt hook, remove the screw that
holds it in place then reassemble on the
opposite side. Be sure to securely tighten
the screw.

OPERATION

WARNING! To reduce the risk of
serious personal injury, turn unit off and
remove the battery pack before making
any adjustments or removing/ installing
attachments or accessories. An accidental

start-up can cause injury.

[14]

CAUTION: Ensure fastener and/or

system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible personal
injury.

1. Place the accessory on the fastener
head. Keep the tool pointed straight at
the fastener.

2. Press switch to start operation. Release
switch to stop operation. Always check
torque with a torque wrench, as the
fastening torque is affected by many
factors including the following:

• Voltage: Low voltage, due to a nearly

discharged battery, will reduce
fastening torque

• Accessory size: Failure to use the

correct accessory size will cause a
reduction in fastening torque.

• Bolt size: Larger bolt diameters

generally require higher fastening
torque. Fastening torque will also
vary according to length, grade, and
torque coefficient.

• Bolt: Ensure that all threads are free

of rust and other debris to allow
proper fastening torque.

• Material: The type of material and

surface finish of the material will
affect fastening torque.

• Fastening time: Longer fastening

time results in increased fastening
torque. Using a longer fastening time
than recommended could cause the
fasteners to be overstressed,
stripped or damaged.

MAINTENANCE

WARNING!: To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making
any adjustments or removing/installing
attachments or accessories. An accidental

start-up can cause injury. Cleaning

WARNING! Blow dirt and dust out of

all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury,
always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING! Never use solvents or other

harsh chemicals for cleaning the non­metallic parts of the tool. These chemicals
may weaken the plastic materials used in
these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid
get inside the tool; never immerse any part
of the tool into a liquid.

Replacing Carbon Brushes

The carbon motor brushes will wear down
and require replacing. The time intervals
between replacements will vary depending
upon the torques being achieved and the
hours of use. It is recommended that the
brushes be checked after each 10 hours of
use. When the length of the carbon brush
reaches 3/16” (4.76 mm), the brushes
should be replaced.

Both carbon brushes should be replaced at
the same time.

1. Remove the rear cover screws

2. Remove the Brush connector

[15]

3. Remove brush

4. Insert new brush and attach
connector

5. Replace rear cover screws

CHARGER CLEANING
INSTRUCTIONS

WARNING! Shock hazard. Disconnect

the charger from the AC outlet before
cleaning. Dirt and grease may be removed
from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.

ACCESSORIES

WARNING! Since accessories, other

than those offered by RHYNO, have not
been tested with this product, use of such
accessories with this tool could be
hazardous. To reduce the risk of injury,
only RHYNO recommended accessories
should be used with this product.

Recommended accessories for use with
your tool are available at extra cost from
your local distributor. If you need any
assistance in locating any accessory, please
contact RHYNO at 844-25RHYNO (844-257-

4966) or visit www.RHYNO.com.

Repairs

The charger and battery pack are
not serviceable.

WARNING! To assure product SAFETY

and RELIABILITY, repairs, maintenance and
adjustment should be performed by a
RHYNO factory service center or a RHYNO
authorized service center. Always use
identical replacement parts.

Register Online

Thank you for your purchase. Register your
product now for:

• WARRANTY SERVICE: Registering your
product will help you obtain more efficient
warranty service in case there is a problem
with your product.

• CONFIRMATION OF OWNERSHIP: In case
of an insurance loss, such as fire, flood or
theft, your registration of ownership will
serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your
product will allow us to contact you in the
unlikely event a safety notification is
required under the Federal Consumer
Safety Act.

Register online at
www.rhyno.com/warranty-registration/

NOTE: Battery warranty voided if the
battery pack is tampered with in any
way. RHYNO and We Cut The Glass, LLC
are not responsible for any injury caused
by tampering and may prosecute
warranty fraud to the fullest extent
permitted by law.

90 DAY MONEY BACK GUARANTEE If you
are not completely satisfied with the
performance of your RHYNO Power Tool,
for any reason, you can return it within
90 days from the date of purchase with a
receipt for a full refund – no
questions asked.

[16]

We Cut The Glass, LLC.

4960 William Flynn Highway, Suite 6, #350, Allison Park, PA 15101

Toll Free: 844-25RHYNO, Fax [phone], Email: [e-mail]

© Copyright 2017 – We Cut The Glass, LLC.

[17]

LIMITED WARRANTY

Every RHYNO tool including battery and battery charger, is warranted to the original
purchaser only to be free from defects in material and workmanship. Subject to
certain exceptions, We Cut The Glass, LLC will repair or replace any part which after
examination, is determined by We Cut The Glass, LLC to be defective in material or
workmanship for a period of two (2) years after the date of purchase unless otherwise
noted. Return of the tool to a RHYNO factory service center location, freight prepaid
and insured, is required. A copy of the proof of purchase should be included with the
return product. This warranty does not apply to damage that personnel, misuse,
alterations abuse, normal wear and tear, lack of maintenance or accidents. The
manufacturing date of the product will be used to determine the warranty period if no
proof of purchase is provided at the time of warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED
HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY RHYNO
Windshield Cutter™. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT
PURCHASE THE PRODUCT. IN NO EVENT SHALL WE CUT THE GLASS, LLC BE LIABLE FOR
ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY
COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A
CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN
OR ORAL. TO THE EXTENT PERMITTED BY LAW, WE CUT THE GLASS, LLC DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE;
TO THYE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED
WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS
WARRANTY AS LASTS, SO THE ABOVE LIMITATION MAY NO APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE. This warranty applies to product sold in
the USA and Canada Only.

No warrant is provided for any product which has been modified in any way. Check
with your international supplier to determine if internatiional warranties apply. Our
sole liability is to repair or replace covered parts and components. This is the exclusive
remedy for consequential damages.

Obtain from us while this warranty is valid and in-effect, prior authorization for return
or repair of covered parts and companents is required.