Rhymeet R1 User Manual
Table of Content
1 Speaker Setup .................................................................................................................................................................. 2
1.1 Buttons ..................................................................................................................................................................... 2
1.2 Power on the device ............................................................................................................................................ 3
1.3 Install Companion Apps..................................................................................................................................... 3
1.4 Set up the speaker ................................................................................................................................................ 3
2 Debug and Diagnostics ................................................................................................................................................ 3
2.1 Updating software................................................................................................................................................ 3
2.2 Factory Reset ......................................................................................................................................................... 5
2.3 Useful commands ................................................................................................................................................. 5
2.3.1 Check Speaker Software Version ......................................................................................................... 5
2.3.2 Dump Speaker Log File ............................................................................................................................ 5
1 Speaker Setup
Button
Description
Long press to enable WPS
Talk button
Volume Down
1.1 Buttons
The definitions of these buttons are
Volume UP
Disable MIC
Short press to Play/Pause;
Press and hold thebutton 3 seconds to turn ON/OFF
The mode switch
MicroSD card slot
1.2 Power on the device
The indicator turns red under charging and turns off when the speaker is fully charged. The fully
charged speaker can work around.
1.3 Install Companion Apps
Before you start, please make sure you have uninstalled any other Rhymeet Apps, including but not
limited to MUZO, iLuv, Fabriq, MUZO, Edge, GGMM etc.
To install the App, launch the default browser (Safari on iOS and Chrome on Android), type the App
address (found in the release notes) in the address bar to access the link, then follow the instruction
on the page to install (usually an installation link or button).
If you use Android you will need to follow this link to allow unknown sources in the settings. If you
use iOS, you’ll have to trust Rhymeet’s enterprise App after the installation, please follow this link
1.4 Set up the speaker
Launch the App you have just installed, follow the instructions on the App to setup the speaker.
Note: The device only supports 2.4GHz Wi-Fi, please make sure you phone is connected to 2.4G
instead of 5G.
Once the device is set up, it will be shown in the App’s device list. You can start using it.
2 Debug and Diagnostics
2.1 Updating software
You may have to update the speaker firmware, MCU firmware when there is a new release. Please
follow the following step to update the software.
1. In the App, check and write down the device’s IP address by following below steps
-> ->
2. Download and UNZIP the firmware you want to update.
3. On a PC that is connected to the same network, open a browser, type the IP address of the
speaker in the address bar and hit enter. You’ll see the web portal of the speaker, as shown
below.
Then click the “System” table
Notice: You can check the firmware version on this page.
4. In the System table, choose the firmware file, then click the “Apply” button, as shown below
5. Wait until the firmware update is complete
6. Repeat the above steps to update other firmware
2.2 Factory Reset
There are two ways to reset the device into factory settings: use a hardware button or use the
companion App. If you don’t find the factory reset button in section 1.1, you will have to factory
reset the device in the companion App. To do this, go to the speaker settings (refer to section 2.1,
step 1), click on Factory Reset. You will hear a voice prompt before the speaker reboots.
2.3 Useful commands
2.3.1 Check Speaker Software Version
http://Speaker_IP/
2.3.2 Dump Speaker Log File
Use a HTTP command
http://Speaker_IP/httpapi.asp?command=getsyslog
Use the App
In the companion App, click on the “Send feedback” button in the App settings.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.
Loading...