R H Peterson l VR 1 User Manual
ROBERT H. PETERSON CO.
MODEL# VR-1
BASIC VARIABLE REMOTE SYSTEM
RECEIVER & TRANSMITTER KIT
.
4
VR-1 SET COMPRISES OF THE FOLLOWING PARTS:
2
1
3
Item No. Part No. Description
1. 10282 Transmitter
2. 10310 Receiver
3. Valve Connection wiring
4. 4x AA Batteries
INSTALLATION AND OPERATING INSTRUCTIONS
NOTICE T O INSTALLER:
Please leave these instructions with the consumer
RECEIVER INSTALLATION STEPS
Step 1. Attach the supplied wires with female connectors to their
proper mating terminals on the valve (See Figure 1).
Step 2. Attach the open wire ends to the terminal block on the
receiver by connecting the marked wire to the positive (+)
terminal and the unmarked wire to the negative (-) terminal.
Tighten down the retaining screws (See Figure 2).
Step 3. To install batteries into the receiver, squeeze together the
tabs on the battery compartment and lift out (See Figure 3).
Insert the four (4) AA batteries (supplied with your kit) into the
compartment, ensuring they are correctly aligned by referring to the
markings in the compartment. Replace compartment.
NOTE: It is recommended that you replace the batteriesannually
with fresh batteries. Always replace the four batteries at same time.
NOTICE TO CONSUMER:
Please retain for future reference
ATTACH FEMALE
CONNECTORS
TO
CORRECT MALE
SPADES ON
VALVE
Figure 1
INSERT WIRING INTO RECEIVER &
TIGHTEN DOWN SCREWS AT BACK
Step 4. IMPORTANT: ACTIVATE YOUR RECEIVER BY PRESSING
THE RESET (LOCATED ABOVE THE SWITCH, SEE FIGURE 3)
WITH A FINE OBJECT SUCH AS A PAPERCLIP.
Place the receiver not closer than 18" to the log set.
An optional receiver cover (PCDC-1 or WCDC-1) is available
from your Peterson dealer.
Step 5. To activate the handset, remove the white tag from rear of
handset.
TO OPERATE REMOTE SEE PAGE 2
PRESS
RESET
TO
ACTIVATE
RECEIVER
REMOVE
THIS TAG
(PULL OUT)
1
OFF
TABS IN
TOWARDS
REMOTE
CENTER
& LIFT OUT
OFF
Figure 3
Figure 2
PRESS
No. L-A2-16904Rev 1 031004
VR-1 TRANSMITTER/RECEIVER OPERATION
PRESS UP
Increasing flame height using the VR-1
Transmitter and Receiver:
A. Set the receiver switch to the center (REMOTE)
position.
B. With the gas supply turned on and the gas log set lit,
point the handset towards the receiver and press the
"UP" Button (the red indicator light on both handset and
receiver should show). Flame height will increase until the
maximum is reached.
Decreasing flame height using the VR-1 Transmitter
and Receiver:
C. Set the receiver switch to the center (REMOTE)
position.
D . While the main burner is lit, point the handset
towards the receiver and press the "DOWN"
Button (the red indicator light on both handset and
receiver should show). Flame height will decrease.
USING THE RECEIVER TO
TOP
CONTROL LOG SET
TO INCREASE FLAME
To turn off the Remote option
and control the log set
manually, set the receiver
switch to "OFF"
( top or bottom position)
To set the switch for Remote
use, set the receiver switch to
"REMOTE"(center position)
OFF
REMOTE
OFF
PRESS DOWN
TO DECREASE FLAME
FCC ID: RWPVR-1
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
ROBERT H. PETERSON COMPANY
VALVES and SAFETY PILOT ASSEMBLIES
LIMITED WARRANTY
All Peterson Valves and Safety Pilot Assemblies are covered by a one (1) year limited warranty.
Defective or broken parts for replacement must be returned to your dealer or to the factory, freight prepaid. Item will be repaired or replaced
at factory option, and returned to purchaser, freight collect.
This warranty does not cover parts becoming defective by misuse, accidental damage, improper handling and/or installation nor does
it cover labor or labor related charges. Valves and pilot assemblies must be installed in accordance with local code and as outlined in
the enclosed instructions.
This warranty specifically excludes liability for indirect, incidental or consequential damage to property. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty
gives you specified legal rights and you may also have other rights which vary from state to state.
Robert H. Peterson Co. 14724 East Proctor Avenue, City of Industry, California 91746
2
Loading...