RHINO PS Series, PS12-050D, PS24-050D, PS12-075D, PS24-075D Installation Instructions Manual
...
1
RHINO Industrial Power Supplies Installation Instructions Rev: 06/18
www.automationdirect.com
R
hino
P
oweR
S
uPPlieS
– PS S
eRieS
INSTALLATION INSTRUCTIONS
PS Series Industrial Power Supply
* For CE compliance to EN 61000-3-2 (PFHC: Power Factor Harmonic Current) use on 115VAC or with a transformer providing isolation from the
public power mains.
** Adjustable by potentiometer with a screwdriver.
To Install
1. Read and follow Safety and Installation instructions on the back of this page.
2. Hook top of power supply’s DIN rail clip on DIN rail
3. Push down tab on top of power supply to open DIN rail clip.
4. Rotate power supply into DIN rail and release tab.
5. Verify the DIN rail clip is securely fastened on DIN rail.
6. Connect wires as indicated on power supply.
Part Number
AC-Input Voltage
Range
Output Power
max.
Output
** Output Voltage
Adjustment Range
Recommended Circuit
Breaker (Characteristic
C)
PS12-050D
93 - 264V AC
Universal Input
50 Watt
12.0VDC / 3.5A 12.0 - 14.0VDC
5A
PS24-050D
24.0VDC / 2.0A 24.0 - 28.0VDC
PS12-075D
115V AC/230V AC selectable
93 - 132V AC
187 - 264V AC
50 / 60Hz
75 Watt
12.0VDC /6.0A 12.0 - 14.0VDC
PS24-075D
24.0VDC / 3.0A 24.0 - 28.0VDC
PS24-150D*
150 Watt 24.0VDC / 6.0A 24.0 - 28.0VDC 10A
PS24-300D*
300 Watt 24.0VDC / 12.0A 24.0 - 28.0VDC 16A
PS24-600D
600 Watt 24.0VDC / 20.0A 24.0 - 28.0VDC
20A
PS24-500D
115V AC
93 - 132V AC
500 Watt 24.0VDC / 20.0A 24.0 - 28.0VDC
Operating temperature range: Natural Air
Convection Cooling
-25°C - +70°C max -13°F - +158°F max Free Space Requirements: Top and Bottom: 3.15 in (80 mm)
Both Sides: 1.97in (50mm)
Output Power Derating:
above +50°C (122°F) → 2%/°C .................... Ambient air temperature measured 0.39in (10mm) below
power supply
Storage temperature range:
-25°C - +85°C max -13°F - +185°F max
Connections:
Pluggable screw type terminal COMBICON
22-10 AWG (0.5-6.0mm2) wire
Recommended tightening torque 0.5 to 0.7Nm (4.5 to 6.2lb.in.)
Use all terminals.
Use a screwdriver with 0.1378” (3.5 mm) blade width (AutomationDirect part DN-SS3).
Case material:
Aluminum (chassis) and Zinc-plated steel (cover)
Input current: @ Vin=115VAC @ Vin=230VAC Power Consumption @ Vin=115VAC @ Vin=230VAC
PS12-050D 1.2A typ. 0.7A typ. PS12-050D 62 Watt typ. 60 Watt typ.
PS24-050D 1.2A typ. 0.7A typ. PS24-050D 62 Watt typ. 60 Watt typ.
PS12-075D 1.7A typ. 0.9A typ. PS12-075D 87 Watt typ. 86 Watt typ.
PS24-075D 1.7A typ. 0.9A typ. PS24-075D 87 Watt typ. 86 Watt typ.
PS24-150D 3.0A typ. 1.7A typ. PS24-150D 168 Watt typ. 165 Watt typ.
PS24-300D 5.4A typ. 3.3A typ. PS24-300D 338 Watt typ. 330 Watt typ.
PS24-500D 9.5A typ. PS24-500D 545 Watt typ.
PS24-600D 10.5A typ. 6.4A typ. PS24-600D 660 Watt typ. 652 Watt typ.
1-800-633-0405
2
RHINO Industrial Power Supplies Installation
inStallation and Safety inStRuctionS
Safety Instructions:
Before installation read these instructions carefully and
completely. These installation instructions cannot cover every
possible installation, operation or maintenance situation. Further
information can be obtained from the product data sheets, which
can be downloaded, from the Internet at http://www.automationdirect.com.
The power supplies are constructed in accordance with the safety
requirements of IEC/EN60950, UL 1950, UL508 and UL 1604.
They are approved (BG-mark) in accordance with EN60950,
EN50178 and fulfill the requirements of the Low Voltage
Directive (LVD). They are UL and cUL listed in accordance to
UL 1950 (recognized), UL508 (listed) and UL 1604 class I, Div.
2 Groups A, B, C and D hazerdous locations (listed).. Before
any installation, maintenance or modification work ensure that
power source is off and properly secured to remain off. Touching
of any live components or improper handling of this power
supply can result in death, severe personal injury or substantial
property damage. Safe operation is dependent on proper storage,
handling, installation and operation.
Compliance with the relevant national regulations (in the USA,
Europe or other countries) must be ensured. Before operation is
started the following conditions must be ensured:
• Connections to mains supply in compliance with national regulations
(NEC, NEMA, VDE0100 and EN50178).
• Use of stranded wires; all strands must be fastened in the terminal
blocks (Potential danger of contact with the case).
• Power supply and mains cables must be sufficiently fused.
• Degree of protection I to IEC536. The non-fused protective earth
connection must be connected to the FG terminal.
• All output wires must be rated for the power supply output current and
must be connected with the correct polarity.
• Sufficient cooling must be ensured.
Never work on the power supply if power is applied! Risk of
electric arcs and electrical shock, which can cause death, severe
personal injury or substantial property damage.
Warning: Hazardous voltages and components storing a very
substantial amount of energy are present in this power supply
during normal operating conditions. However, these are inaccessible. Improper handling may result in an electric shock
or serious burns! Do not open the power supply until at least
5 minutes after it has been disconnected from the mains on all
poles.
• Only trained personnel may open the power supply.
• Do not introduce any objects into the power supply. The output
voltage adjustment potentiometer may only be actuated using an
insulated screwdriver.
• Keep away from fire and water
Installation Instructions:
This power supply is designed for professional indoor systems.
In operation the power supply must not be accessible. It may be
installed and put into service by qualified personnel only.
Do not operate without Protective Earth (PE) connection! To
comply with EMC and safety standards (CE mark, approvals) the
power supply must be operated only if PE terminal is connected
to the non-fused earth conductor.
These power supplies are designed for DIN-rail mounting
upright on horizontally mounted DIN-rail on a flat vertical
surface, as shown. Do not cover any ventilation holes. Observe
free space requirements and power derating for temperatures
above 122°F (50° C).
The internal fuse is not accessible, as it is not intended user
replace it. If this internal fuse has blown, the power supply has
an internal defect and, for safety reasons, must be discarded or, if
under warranty, returned. For continued protection against risk
of fire, do not replace internal fuse with a fuse of different type
or rating.
Recycling: The unit contains elements that are suitable for
recycling, and components that need special disposal. You are
therefore requested to make sure that the power supply will be
recycled at the end of its service life.
WARNING: To minimize the risk of potential safety problems,
follow all applicable local and national codes that regulate the
installation and operation of your equipment. These codes vary
from area to area and it is your responsibility to determine which
codes should be followed, and to verify that the equipment,
installation, and operation are in compliance with the latest revision of these codes.
• Equipment damage or serious injury to personnel can result from the
failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your
particular application, nor do we assume any responsibility for your
product design, installation, or operation.
• If you have any questions concerning the installation or operation of
this equipment, or if you need additional information, please call us at
770-844-4200.
• This publication is based on information that was available at the
time it was printed. At Automationdirect.com , we constantly strive
to improve our products and services, so we reserve the right to make
changes to the products and/or publications at any time without notice
and without any obligation. This publication may also discuss features
that may not be available in certain revisions of the product.
Loading...