RHINO FM60A, FM72A Parts Manual

FM60A/72A

Rear Discharge

60A & 72A Rotary Mowers

Rev 11-12 Effective S/N FM60A-14000 to Current Part No. 00778236P

FM72A-15800 to Current

P ART'S MANUAL

An Operator's Manual was shipped with the equipment in the
Manual Canister. This Operator's Manual is an integral part of
the safe operation of this machine and must be maintained
with the unit at all times.
the Safety and Operation Instructions contained in this manual
before operating the equipment. If the Operator's Manual is
not with the equipment, contact your dealer or Servis-Rhino
(800-446-5158) to obtain a Free copy before operating the
equipment.

READ, UNDERSTAND, and FOLLOW

RHINO

1020 S. Sangamon Ave.
Gibson City , IL 60936
800-446-5158
Email: [e-mail]

®

© 2005 Alamo Group Inc.

TO THE OWNER/OPERATOR/DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.

Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.

PARTS

SECTION

Parts Section – 1

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the proper

Part Number when ordering Replacement Safety Decals.

For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:

RHINO

®

1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: [e-mail]

©2005 Alamo Group Inc.

Parts Section – 2

PART NAME INDEX

BELT ASSEMBLY 60" .......................................................................................................................................................... 14

BELT ASSEMBLY 72" .......................................................................................................................................................... 15

BLADE AND SPINDLE ASSEMBLY ..................................................................................................................... 9

CASTER WHEEL ASSEMBLY .......................................................................................................................... 12

DRIVELINE ASSEMBLY......................................................................................................................................................... 5

GEARBOX ASSEMBLY.......................................................................................................................................................... 6

OPTIONAL QUICK ATTACH HITCH KIT Rev 07-04 ........................................................................................................... 16

ROLLER- FRONT (EXTRA EQUIPMENT)........................................................................................................................... 11

SAFETY DECAL SHEETS ................................................................................................................................................... 17

SHIELD ASSEMBLY Rev 09-05............................................................................................................................................. 8

SPINDLE ASSEMBLY .......................................................................................................................................................... 10

3-POINT LIFT ASSEMBLY..................................................................................................................................................... 4

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 3

3-POINT LIFT ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

1 00757949 1 BAR TOP LINK BD80
2 00768320 4 BAR, HITCH
3 00769453 2 BAR-A-FRAME
4 00769549 2 BAR-REAR LIFT STRAP FM60A

00768319 2 BAR, REAR LIFT STRAP FM72A
5 00761724 4 BUSHING HITCH
6 00762082 6 BUSHING HITCH
7 00757953 1 BUSHING 1-1/4X7/32X3 A-FRAME
8 00603500 2 PIN, HITCH CAT I
9 37107B12 1 PIN TOP LINK CAT 1(PLATED)
10 37107B13 1 CLIP-X HAIR PIN
11 00037200 3 LOCKNUT
12 00748598 1 HEXB 3/4-10UNC 5-1/2 PL5
13 02929200 2 HHCS 3/4-10UNC 1-1/2 PL5
14 2196 2 CLIP (LYNCH PIN), 13/32 DIA.
15 02793900 4 HHCS 7/8-9UNC 2-1/2 GR 5
16 5JRC1490 4 NUT TOPLOCK 7/8 NC PLB
17 00750952 2 HEXB,5/8NC X 2-1/2,ZP,GRD5
18 00695100 4 LOCKNUT
19 00001400 4 FLATWASHER
20 00008300 2 BOLT
21 00778212 1 WDMT,DECK - FM60A

00778203 1 WDMT,DECK - FM72A

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 4

DRIVELINE ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00768041A - DRIVELINE

1 00764500A 2 COMPLETE COLLAR YOKE
2 00756231 2 CROSS & BEARING KIT SERIES 40
3 00759169 1 PIN ROLL 8mm X 60mm
4 00759165 1 PIN ROLL INNER TUBE
5 00764506 1 COLLAR-GUARD-RETAINER
6 00754330 6 BOLT, NYLON - SAFETY SHIELD]
7 00764507 1 COLLAR-GUARD-RETAINER
8 00768168 1 SHIELD, ASY, CMPLT
9 00768165 1 DRIVELINE, HALF ASY, OUTER
10 00768164 1 DRIVELINE, ASY, INNER HALF
11 00774079 2 KIT,SLIDE COLLAR REPAIR

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 5

GEARBOX ASSEMBLY

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 6

GEARBOX ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00777688 - ASY,GEARBOX

1 00778239 1 HOUSING GEARBOX
2 2716532 2 SNAP RING
3 2716540 1 CAP PLUG
4 00564800 1 BEARING, BALL
5 00754761 2 SHIM
6 2716564 1 SHIM KIT
7 00755615 2 BEARING
8 2716656 1 LOCKNUT
9 00778240 1 SEAL OUTPUT
10 00778241 1 SHAFT INPUT
11 00763206 1 SEAL, INPUT SHAFT
12 00754757 1 BEARING
13 00778242 1 COVER GEARBOX
14 00778243 1 SHIM
15 00755633 1 PLUG,3/8"
16 00756649 1 SNAP RING
17 00778244 1 GEAR ,CROWN
18 00772980 1 PLATE
19 00771879 1 SHIM
20 00778245 1 SHAFT, PINION
21 00778246 1 WASHER, EXTERNAL TOOTH
22 4840 1 NUT, CASTLE
23 00771856 4 BOLT METRIC
24 00778187 1 PLUG,BREATHER DIPSTICK
25 70497 1 COTTER PIN

00765444 1qt QT,ALAMO 000 GEAR LUBE

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 7

SHIELD ASSEMBLY Rev 09-05

ITEM PART NO. QTY. DESCRIPTION

1 00774843 1 PLATE GEARBOX MOUNT
2 00777538 1 SHIELD,RH MOLDED BELT FM60A

00777540 1 SHIELD,RH MOLDED BELT FM72A
3 00777539 1 SHIELD,LH MOLDED BELT FM60A

00777541 1 SHIELD,LH MOLDED BELT FM72A
4 00769933 1 NUT-PLASTIC KNOB 3/8 NC PL
5 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5
6 00777688 1 ASY,GEARBOX
7 00001800 8 LOCKNUT
8 00002700 4 FLATWASHER
9 26168 6 CRG-BLT 3/8 X 1 GR5
10 00695100 4 LOCKNUT
11 00008300 4 BOLT
12 00769451 1 PLATE-GEARBOX SLIDE
13 02886900 4 CARR 1/2-13UNC 1-1/2 PL5
14 00769446 1 PLATE-GEARBOX ADJUSTMENT
15 00013901 2 NUT
16 00769898 1 BOLT 3/8 NC 4-1/2 PL2
17 02961255 6 PUSHNUT, BOLT RETAINER, 3/8
18 00758582 1 SHIELD,IMPLEMENT
19 00011700 4 LOCKWASHER
20 00023500 4 FLATWASHER
21 02958784 4 BOLT METRIC 8-P1.25- 20MM PL5
22 02030700 4 HHCS 1/2-13UNC 1-1/4 PL5
23 00011100 1 FLATWASHER 3/8 PL STD

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 8

BLADE AND SPINDLE ASSEMBLY Rev 07-05

ITEM PART NO. QTY. DESCRIPTION

1 00778152 3 FM60A STD BLADE 2 1/2 X 1/4 X 20 7/16 CCW

00766811 3 FM60 OPT HD BLADE 3 X 3/8 X 20 7/16 CCW

00778178 3 FM72A STD BLADE 2 1/2 X 1/4 X 24 1/2 CCW

00765445 3 FM72A OPT HD BLADE 3 X 3/8 X 24 1/2 CCW

2 00766480 3 BOLT,BLADE 5/8-18 X 1-1/2 LH
3 00756077 3 WASHER,5/8 HARDENED
4 00753642 12 HHCS,3/8NC X 1-1/4,ZP,GRD5
5 03101646 12 LOCKWASHER,3/8,MEDIUM-ZP
6 00777699 3 ASY,SPINDLE

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 9

00778223 3 FM72A OPT UPDRAFT BLADE 2-1/4 X 1/4 X 24-1/4 CCW

SPINDLE ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00777699 - ASY,SPINDLE HOUSING

1 00776434 1 SPINDLE,SHAFT
2 00765411 1 SEAL,PROTECTOR
3 00778161 1 HOUSING, SPINDLE
4 00777723 1 NUT,SPECIAL ADJUSTING
5 5312314 2 BEARING CONE LM48548
6 70044 2 BEARING CUP LM48510
7 00766549 2 SEAL
8 15B1200 1 WASHER
9 00777722 1 NUT,HEX TOPLOCK JAM
10 00003500 1 ZERK FITTING 1/8 STRAIGHT
11 00765813 1 KEY-SQ 1/4 X 3/4 LG
12 02957080 1 SETSCREW

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 10

ROLLER- FRONT (EXTRA EQUIPMENT)

ITEM PART NO. QTY. DESCRIPTION

1 00001400 2 FLATWASHER
2 00002000 4 BOLT
3 00755153 1 PIN-COTTER 3/16 X 1-1/2 PLATED
4 4528 4 NUT, LOCK 3/8-16 FLG WHIZ
5 4860 1 WLDMT, AXLE
6 00765317 1 PLATE-BRACKET-LH
7 00765316 1 PLATE-BRACKET-RH
8 4909 1 ROLLER-FRONT

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 11

CASTER WHEEL ASSEMBLY Rev 08-05

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 12

CASTER WHEEL ASSEMBLY Rev 08-05

ITEM PART NO. QTY. DESCRIPTION

1 00761503 8 SPACER 1-1/2 OD X1ID X 1/2LG
2 00766954 4 FORK
3 00778248 4 ASSY- SOLID TIRE WHL

00778247 4 ASSY- PNEUMATIC TIRE WHL (OPTIONAL)
3A 00767637 8 BUSHING-1 FOR WHL #00769862
4 00002700 4 FLATWASHER
5 00778145 4 AXLE PIN
6 00774839 2 AXLE ARM FM60A/FM72A
7 00767637 8 BUSHING-1 FOR WHL #00769862
8 00761504 16 SPACER 1-1/2 OD X 1ID X1LG
9 4805 4 PIN, SNAPPER 1/4 X 2
10 00761453 8 BEARING FLANGE
11 4720 4 GREASE FITTING 1/8 SELF TAP
12 02957009 4 HHCS 3/8 NC 3-1/2 PL5
13 00761961 8 WASHER FM60A

00761961 8 WASHER FM72A
13A 00774848 2 BACKING PLATE (FM72A ONLY)
14 4528 4 NUT, LOCK 3/8-16 FLG WHIZ
15 00765338 8 SPACER 1-1/2OD X 1ID X 1/4LG
16 00763662A 4 TIRE/WHEEL/COMP. (PNEUMATIC)

00769862 4 SOLID TIRE COMPT 10X3.25 RIB
16A 00763703 4 BEARING-ROLLER-1
16B 00763704 4 BEARING-END-CAP-PLAIN
16C 00763705 4 BEARING-END-CAP-NOTCHED
17 00750959 4 HEXB,1/2NC X 1,ZP,GRD5

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 13

BELT ASSEMBLY 60"

ITEM PART NO. QTY. DESCRIPTION

1 00778151 3 SHEAVE,DBL GR,5.0 OD
2 00778150 1 SHEAVE,DBL GR,10.55 OD
3 00777722 3 NUT,HEX TOPLOCK JAM 3/4-10 PLB
4 15B1200 3 WASHER 3/4 P SAE
5 00765813 4 KEY-SQ 1/4 X 3/4 LG
6 00778228 1 BELT (MATCHED SET OF 2)

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 14

BELT ASSEMBLY 72"

ITEM PART NO. QTY. DESCRIPTION

1 00777382 3 SHEAVE,DBL GR,5.9 OD
2 00778150 1 SHEAVE,DBL GR,10.55 OD
3 00777722 3 NUT,HEX TOPLOCK JAM 3/4-10 PLB
4 15B1200 3 WASHER 3/4 P SAE
5 00765813 4 KEY-SQ 1/4 X 3/4 LG
6 00778229 1 BELT (MATCHED SET OF 2)

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 15

OPTIONAL QUICK ATTACH HITCH KIT Rev 07-04

ITEM PART NO. QTY. DESCRIPTION

00777570 - KIT, QUICK ATTACH HITCH

1 00757949 1 TOP LINK
3 00768320 4 BAR, HITCH
4 00769453 2 BAR-A-FRAME
5 00769549 2 BAR-REAR LIFT STRAP
7 00762082 6 BUSHING HITCH
8 00603500 2 ASY,CAT.1 HITCH PIN W/LW & NUT
9 37107B12 1 PIN TOP LINK CAT 1(PLATED)
10 37107B13 1 CLIP-X HAIR PIN
12 00777564 2* BUSHING LOWER OUTSIDE HITCH PIN
13 00777563 2* BAR, FRONT HITCH
14 00777566 1* BUSHING, UPPER INSIDE HITCH PIN
15 00777567 1* BUSHING, UPPER OUTER HITCH PIN
16 00777569 2* BAR, TOGGLE
17 00777565 4* BUSHING, REAR TOGGLE
18 00002701 2* FLATWASHER,3/4,TYPE AW,ZP
19 00002700 10* FLATWASHER 1/2 PL STD
20 00749130 4* HHCS 1/2-13UNC 1-3/4 PL5
21 314018H5C 1* HEX CAP 1/2-13 X 4 1/2 GR.5
22 00001800 5* LOCKNUT TLM 1/2 NC PLB
23 00777568 2* SPACER, 2.50 OD X 1.69 ID X 1/4"
24 2196 2 CLIP (LYNCH PIN), 13/32 DIA.

* INCLUDED IN KIT # 00777570

NOTE: Hitch frame bars must be in position as shown for hitch to work properly

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 16

SAFETY DECAL SHEETS

ITEM PART NO. QTY. DESCRIPTION

2 00777532 1 SHEET,FM60A DECAL
3 00777533 1 SHEET,FM72A DECAL
4 2738332 1 DECAL, RED OBLONG REFLECTOR (NOT SHOWN)

FM60A/72A (Sep-03) Rev 09-05

©2007 Alamo Group Inc. Parts Section – 17

SERVIS-RHINO

LIMITED WARRANTY

1. LIMITED WARRANTIES

1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)
that the goods purchased are free from defects in material or workmanship.

1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.

1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.

1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.

2. REMEDIES AND PROCEDURES.

2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.

2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.

2.03.Purchaser is responsible for returning the goods in question to the Dealer.

2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a ) Repair or replace the defective goods or part(s) or
(b ) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)

if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.

The choice of remedy shall belong to Manufacturer.

2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans­portation cost for the goods or part(s) from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.

3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES

WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.

3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR

USE OF THE GOODS.

3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO

PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM

THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE

ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.

3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS

OCCURRED.

4. MISCELLANEOUS.

4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,

Texas.

4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall

be deemed to be a waiver of any other term.

4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the

invalidity of such provision shall not invalidate any other provisions herein.

4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.

Servis-Rhino Implement Model _______________________________ Serial Number ________________________________

Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION:
READ YOUR OPERATOR'S MANUAL

RHINO

®

1020 S. Sangamon A ve.
Gibson City, IL 60936
800-446-5158
Email: [e-mail]

R

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily
find the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and

2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and

3. Ensure that each employee uses such Seatbelt while the tractor is moving; and

4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected
area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.

2. Where possible, avoid operating the tractor near ditches, embankments, and holes.

3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.

4. Stay off slopes too steep for safe operation.

5. Watch where you are going - especially at row ends, on roads, and around trees.

6. Do not permit others to ride.

7. Operate the tractor smoothly - no jerky turns, starts, or stops.

8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.

9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machinery
guards in place...

Please work, drive, play and live each day with care and concern for
your safety and that of your family and fellow citizens.

Printed U.S.A.

P/N 00778236PFM60A/FM72A