RHINO DIGITAL VIDEO RECORDER, ANX-470, ANX-870, ANX-1670 User Manual
DIGITAL VIDEO RECORDER
1
W
ARNING
This symbol is intended to alert the user to the presence of unprotected
“Dangerous voltage" within the product's enclosure that may be strong
enough to cause a risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
NOTE: This equipment has been tested and found to comply with the limits for a class
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate
collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling
of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The recycling of materials will
help to conserve natural resources. For more detailed information about recycling of this product,
please contact your local city office , your household waste disposal service or the shop where you
purchased the product.
USER’S MANUAL
2
PRECAUTION
• Make sure to switch the power off before you install the DVR.
• There is the danger of an electric shock if the DVR is opened by an unqualified service
engineer or installer.
• Avoid using the DVR outside of the reference temperature and humidity indicated in the
specification.
• Avoid exposing the DVR to violent movement or vibration.
• Do not use or store the DVR in direct sunlight or near to any source of heat.
• Do not place any object into the holes used for air circulation.
• Always use the DVR in a well ventilated location to prevent overheating.
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• When the cooling fan is stopped, the below warning message will be displayed
at the monitor.
“ COOLING FAN IS STOPPED, TURN THE POWER OFF AND CHECK COOLING FAN”
In this case, do the power off right away and check the cooling fan working.
• The HDD is recommended to use enhanced IDE Hard Disc Drive type made by
Western Digital, Seagate, Hitachi and IBM, Samsung Electronics.
EXTERNAL HDD BAY (If specified as an accessory)
• Always attach the joining cable lead between the DVR and the HDD Bay for correct system
management. (Refer to the section describing the installation procedure for the EXTERNAL
HDD BAY)
• While the EXTERNAL HDD BAY is in operation never disconnect the power or connecting
cable. Before opening the top cover, you must turn off the power by the switch on the front
panel of the DVR. And then disconnect the power cord and other cables. Failure to follow
this procedure will result in lost data or malfunction of the system.
• When replacing any HDD always make certain that the replacement part is fitted in the same
place and with the same connections as the original.
All the safety and operating instructions must be read before the unit is operated.
DIGITAL VIDEO RECORDER
3
CONTENTS
TABLE OF CONTENTS
1. FEATURE LIST ----------------------------------------------------------------------------------
2. PACKING DETAIL ------------------------------------------------------------------------------------------
3. LOCATION AND CONTROL -----------------------------------------------------------------
3.1 FRONT PANEL CONTROLS -------------------------------------------------------------------------------
3.2 REAR PANEL CONNECTORS -----------------------------------------------------------------------------
4. INSTALLATION ---------------------------------------------------------------------------------------------
4.1 TOTAL CONNECTION LAY-OUT -------------------------------------------------------------------------
4.2 INDIVIDUAL CONNECTION --------------------------------------------------------------------------------
4.2.1 CAMERA ------------------------------------------------------------------------------------------
4.2.2 AUDIO ---------------------------------------------------------------------------------------------
4.2.3 MONITOR -----------------------------------------------------------------------------------------------
4.2.4 EXTERNAL HDD BAY--------------------------------------------------------------------------
4.2.5 USB 2.0 Ports -----------------------------------------------------------------------------------
5. OPERATION --------------------------------------------------------------------------------------
5.1 FACTORY DEFAULT ------------------------------------------------------------------------------
5.2 FRONT PANEL CONTROLS ------------------------------------------------------------------------
5.2.1 POWER ON / OFF --------------------------------------------------------------------------
5.2.2 SCREEN DISPLAY ------------------------------------------------------------------------------
5.2.3 RECORD ---------------------------------------------------------------------------------------
5.2.4 SEARCH & PLAYBACK ------------------------------------------------------------------
5.2.5 PLAY BUTTON INFORMATION ------------------------------------------------------------
5.2.6 DIGITAL ZOOM------------------------------------------------------------------------------------
5.2.7 SCREEN SELECT (LV/PB)----------------------------------------------------------------------
5.2.8 SPOT MONITOR-----------------------------------------------------------------------------------
5.2.9 COPY ----------------------------------------------------------------------------------------------
5.2.10 DVR STATUS ------------------------------------------------------------------------------------
5.2.11 PTZ CONTROL------------------------------------------------------------------------------------
5.2.12 FUNCTION BUTTON ---------------------------------------------------------------------------
5.2 REMOTE CONTROLLER-------------------------------------------------------------------------
5.3 MOUSE CONTROL --------------------------------------------------------------------------------
6. MENU SETUP ----------------------------------------------------------------------------------------------------
6.1 QUICK SETUP -----------------------------------------------------------------------------------------------
6.2 SCREEN ------------------------------------------------------------------------------------------------------
6.3 RECORD ----------------------------------------------------------------------------------------------------
6.4 EVENT ---------------------------------------------------------------------------------------------------------
6.5 SYSTEM ------------------------------------------------------------------------------------------------------
6.6 LINK -------------------------------------------------------------------------------------------------------------
6.7 SEARCH ------------------------------------------------------------------------------------------------------
6.8 COPY -------------------------------------------------------------------------------------------------------------
6.9 EXIT -------------------------------------------------------------------------------------------------------------
5
7
8
8
9
10
10
11
11
11
12
13
14
15
15
18
18
18
20
20
24
25
25
26
27
31
31
32
33
34
34
34
36
44
50
54
62
64
65
65
USER’S MANUAL
4
CONTENTS
7. EXTERNAL TERMINAL INFORMATION ---------------------------------------------------
7.1~2 RS-485 / T.ADJ-----------------------------------------------------------------------------------------
7.3~4 RELAYOUT / ALARM --------------------------------------------------------------------------------------
7.5~6 VGA / SERIAL ----------------------------------------------------------------------------------------------
7.7~8 ETHERNET/USB / REMOTE -----------------------------------------------------------------------------
8. SPECIFICATIONS ----------------------------------------------------------------------------
9. 256 CAMERA INTEGRATION SYSTEM --------------------------------------------------
10. HDD INSTALLATION ------------------------------------------------------------------------
10.1 INTERNAL HDD INSTALLATION -------------------------------------------------------------------
10.2 DVD±RW(or CD-RW) installation-------------------------------------------------------------------
11. NETWORK CLIENT VIEWER MANUAL----------------------------------------------
11.1 INSTALLATION OF NETWORK VIWER SOFTWARE ------------------------------------------
11.1.1 SYSTEM REQUIREMENT ---------------------------------------------------------------------
11.1.2 NETWORK ENVIRONMENT ------------------------------------------------------------------
11.1.3 INSTALLATION -----------------------------------------------------------------------------------
11.2 CONNECTING TO DVR ---------------------------------------------------------------------------------
11.2.1 ADD A NEW SITE INFORMATION --------------------------------------------------------
11.2.2 CHANGE THE SITE INFORMATION ------------------------------------------------------
11.2.3 DELETE THE SITE INFORMATION -------------------------------------------------------
11.2.4 CONNECT TO A DVR -----------------------------------------------------------------------
11.3 DVR SEARCH ---------------------------------------------------------------------------------------------
11.4 HDD SEARCH ---------------------------------------------------------------------------------------------
11.5 FILE SEARCH -----------------------------------------------------------------------------------------------
11.6 ARRANGE THE SCREEN ------------------------------------------------------------------------------
11.7 OPTION -------------------------------------------------------------------------------------------------------------
11.8 CONTROL---------------------------------------------------------------------------------------------------
11.8.1 SCREEN DISPLAY-----------------------------------------------------------------------
11.8.2 CONTROLLER----------------------------------------------------------------------------
11.8.3 PTZ-------------------------------------------------------------------------------------------
11.8.4 SETUP--------------------------------------------------------------------------------------
11.8.5 STATUS-------------------------------------------------------------------------------------
11.8.6 PRINT---------------------------------------------------------------------------------------------
11.8.7 COPY----------------------------------------------------------------------------------------------
11.8.8 AUDIO IN-----------------------------------------------------------------------------------------
11.8.9 AUDIO OUT--------------------------------------------------------------------------------------
11.8.10 TIME SEARCH------------------------------------------------------------------------------------
11.8.11 EVENT SEARCH--------------------------------------------------------------------------------
11.8.12 BLOCK SEARCH------------------------------------------------------------------------------
11.8.13 LOG SEARCH----------------------------------------------------------------------------
11.9 KEY INFORMATION ------------------------------------------------------------------------------------
66
66
67
68
69
70
73
74
74
77
79
79
79
79
79
79
80
80
80
80
81
81
82
82
83
84
84
84
85
85
86
86
87
87
87
88
88
89
89
90
DIGITAL VIDEO RECORDER
5
FEATURES
Chapter 1 Features
Operation
Playback, recording, backup and transmission simultaneously
Real time single or multi-screen display
Pan & Tilt, 2X digital zoom and PIP display
Easy operation by IR remote controller, external keypad controller and USB 2.0 Mouse
Hidden camera option (covert)
User-friendly setup menu and operation
Playback
Multi-screen playback (Full/4/6/7/9/10/13/16 split)
Search by date, time and camera
Preview window on event search mode
Playback mode(frame/ field) setup
Recording
Select of the recording quality grade for each channel
Individual camera frame rate can be set by user
The recording speed of max. 120 images per second (NTSC)
Manual, schedule and event recording
Pre & Post-alarm recording
Select of the recording image size for each channel
4 channels audio recording
Select of the event mode for each channel
Network
Live and playback viewing
Remote control on a networked PC with the exclusive client viewer
(The viewer software is supplied for free.)
Flexible connections - 10/ 100 Mbps Ethernet/ ADSL
Up to 16 network users access simultaneously
Audio transmission between DVR and Client
Dynamic IP is available
USER’S MANUAL
6
FEATURES
External storage
Automatic backup to selected backup HDD (Event backup/ Mirroring)
Own external storage device to extend the HDD capacity
You can install 10 HDDs in 1 external HDD Bay and connect up to 4 Bay with this DVR.
(250GB X 40HDDs = 10TB, 500GB X 40HDD = 20TB, 1TB X 40HDD = 40TB)
Audio
4 channels audio recording in real time
Audio channel select for each channel
Copy
USB 2.0 external HDD
USB 2.0 memory stick
External CD-RW/ DVD±RW (optional)
General
Software downloading facility via network and USB memory stick
Auto detection of PAL / NTSC
Built-in hardware Watchdog
Automatic time adjustment through Network
VGA output for PC monitor(Optional)
Optional external CDRW or DVD±RW
Loop-through connections
Support of multiple Languages
Graphic User Interface for the MENU screen
Analog Spot
DIGITAL VIDEO RECORDER
7
PACKING DETAIL
Chapter 2 Packing Detail
1. DVR
2. Network Viewer Program CD
3. User’s Manual
4. Remote Controller
5. R-HDD Rack Key
6. Rack Mounts
7. AC Adaptor & Power Cord
8. Batteries (For Remote Controller)
9. HDD Screws
4. Remote controller
3. User’s Manual
1. DVR
2. Network Viewer Program CD
5. R-HDD Rack Key
7. AC Adaptor & Power Cord
6 Rack Mounts
9. HDD Screws
8. Batteries
USER’S MANUAL
8
LOCATION AND CONTROL
Chapter 3 Location and Control
3.1 FRONT PANEL CONTROLS
○
5
○19 ○6○20○27○21○18○4 ○8○12 ○14○10○16○9 ○7 ○2 ○1
○
11○26
○25 ○24○25○22○23 ○15 ○17
Control keys
Description
○1 CD-RW / HDD Rack
Removable HDD rack (Option: Built-in CD-RW or DVD±RW)
○2 USB port USB 2.0 port to use a USB Pen-Driver, Mouse or USB external devices
○3 Remote Sensor
IR receiver for the remote controller
○4 FUNCTION
Audio select (FUNCTION + channel)/ Relay4 User action(FUNCTION + “+” / “-“)
○5 CHANNEL SELECT
Buttons to select the camera or input the password
⑥ MULTI Multi-channel select button
○7 LED Indicator
Display of the status of power(STANDBY), HDD(HDD) and network(RX / TX)
○8 SPOT / ESC
Button to control spot monitor/ ( exit & return ) during the menu setting
○9 LV / PB
Button to convert the Display between real view mode and playback mode
○10 MENU
Button to Menu setup / move to the upper direction
○11 COPY(AF)
Button to data-copy menu/ automatically focus in PTZ mode
○12 ALARM RESET
Button to release the event signal/ move the left direction/ PAN left in PTZ mode
○13 AUTO / F(-)
Button to the auto sequence mode/ decrease the value/ focus in PTZ mode
○14 STATUS/ ( enter )
Button to enter the next step/ display the status/ return to home position in PTZ mode
⑮ PIP /
Button to the PIP display mode / move to the Down direction
○
16
D-ZOOM /
Button to control the digital zoom/ move to the right direction/ PAN right in PTZ mode
○17 FREEZE / F(+)
Button to freeze image / increase the value/ focus in PTZ mode
○18 REC( )
Button to enable and stop recording
○19 SLOW( )
Button to control the slow motion of playback speed
○20 PB / PAUSE( )
Button to the playback m ode . If press again, a still picture is displayed during
playback.
○21 FAST( )
Button to speed up the playback speed
○22 DIRECTION( )
Button to change the direction of playback
○23 SEARCH(PRESET)
Button to the search menu / preset in PTZ mode
○24 PTZ Button to control PTZ camera
○25 PTZ Zoom
Button to adjust PTZ Zoom increase/decrease (+/-)
○26 PTZ IRIS
Button to adjust PTZ Lens iris increase/decrease (+/-)
○27 AUDIO SELECT
Button to choose Audio channels
○
3
DIGITAL VIDEO RECORDER
9
LOCATION AND CONTROL
3.2 REAR PANEL CONNECTORS
Port Name Description
○1 CAMERA IN
BNC input ports for cameras
○2 CAMERA OUT
BNC output(looping) ports for cameras
○3 SPOT
BNC output port for spot monitor
○
4
VIDEO OUT
BNC output port for the main monitor
(Same as the RCA video output of the front panel)
○5 AUDIO IN
RCA input ports for an audio signal(4CH Line input)
○6 AUDIO OUT
RCA output port for an audio signal
○7 ETHERNET
Port for 10/ 100Mbps Ethernet/ xDSL
○8 USB1 / USB2
USB 2.0 ports to use USB memory stick, Mouse or the external devices
○9 VGA OUT
Output port for the VGA monitor
This DVR is compatible with TFT LCD monitor in PAL mode.
○10 SERIAL
Connector for debugging. This DVR can be controlled by the other device
through this connector(RS-232C).
○11 S-VIDEO OUT
Output port for the S-video output
○12 GROUND
Earth ground port to connect with the external devices
○13 RS-422 / 485
Terminal blocks of RS-422 or RS-485
○14 T-ADJ
Input and output terminal blocks for time synchronization among DVRs
○15 RELAY OUT
4 relay output terminal blocks
○16 ALARM IN
Input terminal blocks for alarm signals
○17 POWER IN
Socket for a 12V/5A power cord
○
4
○
7
○
8
○
10
○
9
○17 ○14 ○16
○
6
○
12
○
13
○11 ○15
○
1
○
2
○
3
○5 ○16
USER’S MANUAL
10
INSTALLATION
Chapter 4 Installation
4.1 TOTAL CONNECTION LAY-OUT
DIGITAL VIDEO RECORDER
11
INSTALLATION
4.2 INDIVIDUAL CONNECTION
4.2.1 Camera
* Connect a female BNC connector of each camera to a male BNC connector, “CAMERA IN” port.
* Connect the looping BNC output to other inputs as required
4.2.2 Audio (*Refer to the specification)
USER’S MANUAL
12
INSTALLATION
Audio Input
- AUDIO IN : Connect the RCA Line Jack of the relevant equipment (for example, a camera with
a built-in microphone) to the AUDIO IN port
Audio Output
- AUDIO OUT : Connect the RCA Line output to a monitor with a built-in speaker
4.2.3 Monitor
- Connect the female BNC for monitor output.
- Connect the male Y/C cable socket for S-VIDEO monitor output.
NOTE
This DVR can be connected only with a line audio and not support a microphone for audio input and output.
To record audio should be enable in the AUDIO setup at the MENU setup.
As the audio is linked to a camera, it is required that linked camera viewed, either in multi-screen view during
playback to hear the audio.
DIGITAL VIDEO RECORDER
13
INSTALLATION
4.2.4 External HDD Bay (XHD-10U)
(USB output)
INSTALLATION PROCESS.
1) Turn off the power of DVR.
2) Connect the grounding conductor between DVR and external HDD bay.
3) Connect the USB cable between DVR and external HDD bay.
4) Connect the power cord of DVR and external HDD bay.
5) Plug the power cord of DVR and external HDD bay.
6) Turn the power of DVR on.
7) After booting the system automatically, press the STATUS button and check the system
information of setting the HDD. (If the HDD is not recognized properly, turn the power of
DVR off first and check the cable connections referring to user’s manual of XHD-10U.)
CAUTION - Do not disjoint the external HDD Bay from DVR in normal operating condition.
NOTE - Please refer to the XHD-10U user’s manual for more information.
USER’S MANUAL
14
INSTALLATION
4.2.5 USB 2.0 ports
○
1
Three USB ports are provided to connect a USB memory stick, One USB port is on the front
panel and the other two are on the rear panel.
○
2
A USB mouse can be connected to one of the ports. You can use the mouse to navigate
through the screens and menus much like you work on a computer.
INSTALLATION PROCESS.
Connect the desired device with DVR as the above pictures.
(For example, USB memory stick, mouse, external storage device etc.)
DIGITAL VIDEO RECORDER
15
OPERATION
Chapter 5 Operation
5.1 FACTORY DEFAULT
MENU Setup>
QUICK SETUP>
QUICK SETUP…………………….….…….…..…..……….OFF
IMAGE SIZE……………………….………………...…….…720x240
RECORD FRAME……………………….……….…….……60
EVENT……….…………………………...…………..……...ALL
PRE RECORD TIME……….…………...….……..………..5SEC
POST RECORD TIME………………….…...…….…..…..10SEC
IMAGE QUALITY…..…………………………….….………FINE
AUDIO RECORD…………………………….………..…….OFF
REMOTE CONTROL ID…………….…..………..………..ALL
SCREEN>
AUTO SEQUENCE
QUAD-A~E/ NINE-A~B/ SIXTEEN………...…....3SEC
ADD AUTO SINGLE….………………..….……...OFF
AUTO-SINGLE CH1~16………………..….…..…3SEC
VIDEO LOSS SKIP..…………………….……..….ON
DISPLAY
HDD FREE SPACE.……………….……….……..ON
HDD FREE SPACE MODE..…...…………..…….PERCENT
RECORD STATUS..………………………....…...ON
CLOCK DISPLAY…………………..…….….….…ON
DATE & TIME MODE..…………….……..…...….NUMBER
TITLE DISPLAY………………………....…….….ON
TITLE MODE…………………………..….….…...TEXT
BORDER COLOR.………………………..….……WHITE
REMOTE CONTROL ID..………….…….….……OFF
TITLE
CH 1~CH 16………………………….…………....CH 1~CH16
MULTI SCREEN
LIVE 4E………………………………….………....2/ 4/ 6/ 8
LIVE 9B…………………………………………....10/11/12/13/14/15/16/1/2
COVERT
CH 1~16………………………….….….………....OFF
SELECT……………………………….………..…..LV&PB&NW
SPOT
SPOT MODE……………………….……………..MANUAL
SPOT SEQ. TIME….……………..….….….…....3SEC
RECORD>
RECORD SETUP
RECORD PROGRAM..………………………......6
RECORD PROGRAM (Refer to page 51)
USER’S MANUAL
16
OPERATION
IMAGE QUALITY
RECORD QUALITY……………………….…….....FINE
AUDIO RECORD
AUDIO 1………………..…………………….…......OFF
AUDIO 2………………..…………………….…......OFF
AUDIO 3………………..…………………….…......OFF
AUDIO 4……………..……………………….…......OFF
REPEAT RECORD
REPEAT RECORD..………………………………..ON
REPEAT RECORD ALARM.…………………..…..5%
PLAY MODE.…………………………………….……........FRAME
BACKUP MODE..……………………………….……........OFF
HOLIDAY
HOLIDAY RECORD…………………………….….OFF
HOLIDAY SETUP(MM/DD) ………………..……..00/00
EVENT>
MOTION DETECTION
CHANNEL…………………………………….……..1
SENSITIVITY…………………………...….……….5
EVENT SCREEN MODE…………………...…….…….…SCREEN HOLD
EVENT CHECK.………………………………..….………OFF
EVENT MESSAGE..…………………………….………....OFF
EVENT MESSAGE RESET……………….……...…..…..5SEC
EVENT BUZZER..…………………………………….…...OFF
SENSOR INPUT
SENSOR 01~16 INPUT TYPE..…………………..NOT USED
RELAY OUTPUT
CH 1~16: ALARM/ V-LOSS/ MOTION..……….…1/ 2/ 3
RELAY 1~3 OUTPUT TIME..………………..……1SEC
RELAY 4 SELECT.….………………….……..……POWER
SYSTEM>
HDD
HDD CONFIGURATION
REC HDD INITIALIZE…..………………….………NO
BACKUP HDD INITIALIZE…………………………NO
CLOCK
TIME ADJUST
INTERNET TIME ADJUST...………………OFF
DAYLIGHT SAVING TIME..…….………....OFF
PASSWORD
MASTER PASSWORD…..…………….…………..11111111
SUPERVISOR PASSWORD.………….…………..22222222
MENU DISPLAY CHECK.……………….…………OFF
REC/PLAY CHECK…..………………….……….…OFF
VIDEO STANDARD…………….…………………………..AUTO
LANGUAGE……………….………..………………….…….ENGLISH
REMOTE CONTROL ID.…………….………..………….. ALL
KEY ECHO…..………………….……………….…………..ON
DVR INITIALIZE.………………….………..…….…………NO
FIRMWARE UPGRADE………………….……….………..NO
LINK>
NETWORK
DHCP……..………………………………….………OFF
PORT……………………………………….………..5200
DIGITAL VIDEO RECORDER
17
OPERATION
RS232C
BAUD RATE..………………….…………….……..115200
DATA BIT……..……………………………….…….8
PARITY BIT….……..……………………….………NONE
STOP BIT……..…………………………….……….1
RS485
SYSTEM ID……..…………………………….…….1
BAUD RATE..………………….……………….…..115200
DATA BIT……..………………………………….….8
PARITY BIT….……..………………………….……NONE
STOP BIT……..……………………………….…….1
PTZ
CH 1~16: MODEL/SPEED/ID….…………………..NONE/9600/1
E-MAIL
SEND E-MAIL………………………………..OFF
SEARCH>
CALENDER SEARCH
SEARCH & COPY
TIME SEARCH
HDD ID…………………………………………..…..NORMAL
CHANNEL…………………..……………………….ALL
EVENT SEARCH
HDD ID……………………………………………....NORMAL
CHANNEL…………………..…………….………....ALL
EVENT…………………..……………….…..………ALL
BLOCK SEARCH
HDD ID………………………………………………..NORMAL
FILE SEARCH
MEDIA………………………………………...……...FRONT USB
BOOKMARK SEARCH
LOG SEARCH
COPY>
COPY STATUS
COPY START/ END/ CUR TIME.………….………2000/00/00 00:00:00
MEDIA FORMAT
FORMAT MEDIA..……………………….…………..USB FRONT
EXIT>………………………………………………………...…….….SAVE ONLY
USER’S MANUAL
18
OPERATION
5.2 FRONT PANEL CONTROLS
5.2.1 POWER ON /OFF
After the connection of power cord and other devices with this DVR, turn the power on.
a. The video signal system (NTSC or PAL) is automatically
detected.
b. Power Failure Recovery
This DVR automatically reverts back to programmed record
parameters upon power restoration.
5.2.2 SCREEN DISPLAY
5.2.2.1 Multi-Display & Full Screen display
a. Multi display
To change a single camera display to the multi camera, press the MULTI button.
b. Full screen display
Press the desired camera number button to display on the monitor.
• If there is no video signal, the video signal system is set to NTSC. Do not input the PAL type video signal or it may
cause the DVR’s malfunction. In this case, turn off and on again.
Use the +10 Button when you select two digit camera numbers.
EX) Camera Number 12 = Press the +10 Button, and then press the No. 2 Button.
CAMERA/NUMBER INPUT buttons are used to input the password in the password lock function.
DIGITAL VIDEO RECORDER
19
OPERATION
5.2.2.2 Auto Sequence Display
<ADD AUTO SINGLE : ON>
- Press the AUTO button, each screen display will be automatically switching according to the AUTO
SEQUENCE setup.
- If you set up “ADD AUTO SINGLE : OFF” in the AUTO SEQUENCE setup menu, the single display
will be skipped.
- To view the single display, set up “ADD AUTO SINGLE : ON” in the AUTO SEQUENCE setup
menu and the single display will be included in the auto sequence display.
- Press the AUTO button again to exit the AUTO mode.
5.2.2.3 Freeze
MULTI SCREEN MODE
At the Multi display mode, press the FREEZE button and then select the desired camera number.
Press the FREEZE button again to release the FREEZE mode.
SINGLE SCREEN MODE
Press the FREEZE button after the desired channel is selected.
Press the FREEZE button again to release the FREEZE mode.
- If you press the MULTI button after pressing the FREEZE button, all the channels will display
still images.
- FREEZE function is not available, when auto mode is selected.
(Refer to AUTO SEQUENCE in the SCREEN menu for further information)
If an event takes place, the AUTO SEQUENCE mode will be cancelled.
Please refer to the AUTO SEQUENCE of Chapter 6 MENU setup for more information.(Page 37)
USER’S MANUAL
20
OPERATION
5.2.3 RECORD
Press the REC button and the following message will be displayed as below;
MANUAL MODE
Press the REC button to begin recording.
To stop recording, press the REC button again. The screen will be turned into real time display
mode.
SCHEDULE MODE
When Schedule mode is selected, the recording will be automatically executed according to the
recording schedule. (Please refer to the SCHEDULE SETUP in the RECORD setup, page 44.)
5.2.4 SEARCH & PLAYBACK
Press the SEARCH button, the SEARCH menu screen appears.
TIME SEARCH
The color of record indication ( NNNNNNNN ) on the screen will be changed according to the type of
recording and refer to the following.
- “ N ” : Manual recording status.
- “ S ” : Schedule recording status.
- “ E ” : Event recording status. (Motion detection/ Video loss/ Sensor)
- “ - ” : Not recording.
If you press the PLAY button in the real time screen mode, playback will be executed from the end of
the previous time search and press the desired channel select button.
To exit the playback mode and see the live screen again, press LV/PB button.
All channels will be displayed by “E” even if an event happened just on one channel.
“E” will be displayed because this unit enters the event record mode when event happened.
If a channel has an event, all channels will be recorded by event recording frame rate to be set
in RECORD PROGRAM menu.
DIGITAL VIDEO RECORDER
21
OPERATION
5.2.4.1 SEARCH & COPY
At the SEARCH menu;
① Move the cursor to TIME SEARCH using or button.
② Press the ENTER button and TIME SEARCH screen appears.
③ Select the desired HDD ID using the (-) or (+) button.
④ Move the cursor to CHANNEL using the or button and select the desired channel using the
(-) or (+) button.
⑤ Move the cursor to the desired position of SEARCH TIME using the , , , buttons, and
then set up the desired time using the(-), (+) buttons.
⑥ Press the ENTER button and you can playback.
⑦ Move the cursor to START COPY and then press the ENTER button to copy.
⑧ Press the ESC button to exit this menu.
5.2.4.2 TIME SEARCH
At the SEARCH menu;
① Move the cursor to TIME SEARCH using or button.
② Press the ENTER button and TIME SEARCH screen appears.
③ Select the desired HDD ID using the (-) or (+) button.
④ Move the cursor to CHANNEL using the or button and select the desired channel using the
(-) or (+) button.
⑤ Move the cursor to the desired position of SEARCH TIME using the , , , buttons, and
then set up the desired time using the(-), (+) buttons to set the search time.
⑥ Press the ENTER button and you can playback.
⑦ Press the ESC button to exit this menu.
USER’S MANUAL
22
OPERATION
5.2.4.3 EVENT SEARCH
At the SEARCH menu;
① Move the cursor to EVENT SEARCH using or button.
② Press the ENTER button and the EVENT SEARCH menu screen appears.
③ Select the desired HDD ID using the (-) or (+) button.
④ Move the cursor to CHANNEL using the or button and select the desired channel using the
(-) or (+) button.
⑤ Move the cursor to EVENT using the or button and select the event type to search using
the (-) or (+) button.
⑥ Move the cursor to the desired position of SEARCH TIME using the , , , buttons, and
then set up the desired time using the(-), (+) buttons.
⑦ Press the ENTER button, and the event list searched appears.
⑧ When the event list appears on the screen, select the desired list using , buttons and
press the ENTER button for the playback.
5.2.4.4 BLOCK SEARCH
At the SEARCH menu;
① Move the cursor to BLOCK SEARCH using or button.
② Press the ENTER button and the BLOCK SEARCH menu screen appears.
- When video loss is detected, up to five seconds of pre-recording data is stored on the HDD and the
details will be listed in the EVENT LIST. The beep sounds and the LED of the ALARM RESET button will
flicker. Press the ALARM RESET button to remove this signal.
- When the unit receives a signal from the sensor input, DVR begins to record the input data according
to the PRE/POST TIME in the RECORD setup and the details will be listed in the EVENT LIST.
CAUTION
ⓐ If the internal HDD(s) is initialized, all of the event images will be deleted.
ⓑ When the unit is in normal recording status, the pre-recording will not be executed.
-
DIGITAL VIDEO RECORDER
23
OPERATION
③ Select the desired HDD ID using the (-) or (+) button.
④ Move the cursor to the desired position of SEARCH TIME using the , , , buttons, and
then set up the desired time using the(-), (+) buttons.
⑤ Press the ENTER, and the list searched appears.
⑥ When the list appears on the screen, select the desired list using , buttons and press the
ENTER button for the playback.
5.2.4.5 FILE SEARCH
At the SEARCH menu;
① Move the cursor to FILE SEARCH using or button.
② Press the ENTER button and the FILE SEARCH screen appears.
③ Select the desired type of MEDIA using the (-) or (+) button.
④ Press the ENTER button, and the list searched appears.
⑤ When the list appears on the screen, select the desired list using , buttons.
⑥ Press the ENTER button for the playback.
5.2.4.6 BOOKMARK SEARCH
At the SEARCH menu;
① Move the cursor to BOOKMARK SEARCH using or button.
② Press the ENTER button and the BOOKMARK SEARCH screen appears.
③ Press the ENTER button, and the list searched appears.
④ When the list appears on the screen, select the desired list using , buttons.
⑤ Press the ENTER button for the playback.
⑤ Press the ENTER, and the list searched appears.
USER’S MANUAL
24
PRECAUTION
<How to make Bookmark list>
① Press the “PB/PAUSE” button to playback.
② Find the desired image using the (-), (+) buttons.
③ Press the “PB/PAUSE” button to see the still picture of the desired image.
④ Press the “PTZ” button to add the BOOKMARK list.
5.2.4.7 LOG FILE SEARCH
At the SEARCH menu;
① Move the cursor to LOG FILE SEARCH using or button.
② Press the ENTER button and the LOG FILE SEARCH screen appears.
③ Move the cursor to the desired position of SEARCH TIME using the , , , buttons,
and then set up the desired time using the(-), (+) buttons.
④ Press the ENTER button, and the list searched appears.
⑤ When the list appears on the screen, select the desired list using , buttons.
5.2.5 PLAY BUTTON INFORMATION
5.2.5.1 SLOW ( )
Press this button to make the speed level which is slower than normal speed (X1) and displayed it at
the upper left side of screen as below;
(If you press this button again, the playback speed will be changed in the order of the below seven
speed level)
i. 1/2 - 2 times slower than normal playback speed
ii. 1/4 - 4 times slower than normal playback speed
iii. 1/8 - 8 times slower than normal playback speed
iv. 1/16 - 16 times slower than normal playback speed
v. 1/32 - 32 times slower than normal playback speed
vi. 1/64 - 64 times slower than normal playback speed
vii. 1/128 - 128 times slower than normal playback speed
-
DIGITAL VIDEO RECORDER
25
OPERATION
5.2.5.2 PB / PAUSE ( )
Press this button to begin playback at normal speed (X1).
Press this button again to pause the playback.
<How to playback a section repeatedly>
① Press the “PAUSE” button at the position to start to playback.
② And then press the “AUTO” button to set up the A position(starting position).
③ Press the “PB” button and playback to find the ending position.
④ Press the “PAUSE” button at the position to end to playback.
⑤ And then press the “FREEZE” button to set up the B position(ending position).
⑥ Press the “PB” button to playback between A to B repeatedly.
<How to release the section repetition playback>
① Press the “PAUSE” button.
② Press the “AUTO” button and then press the “FREEZE” button to exit the section repetition
playback mode.
5.2.5.3 FAST ( )
Press this button to make faster the speed level which is higher than normal speed (X1) and
displayed at the upper left side of screen as below:
i. 2 - 2 times faster than normal playback speed
ii. 4 - 4 times faster than normal playback speed
iii. 8 - 8 times faster than normal playback speed
iv. 16 - 16 times faster than normal playback speed
v. 32 - 32 times faster than normal playback speed
vi. 64 - 64 times faster than normal playback speed
vii. 128 - 128 times faster than normal playback speed
(However much data may be recorded can be searched in 3 seconds)
5.2.5.4 DIRECTION ( )
Press this button to change direction to forward ( )or backward ( ) in playback mode.
5.2.6 DIGITAL ZOOM
NOTE
Press DIR button to make a reversed playback from the end of recorded or played images
during the real time display mode.
NOTE
If you press the “PB” button to playback, it will playback from the end of played final image.
USER’S MANUAL
26
PRECAUTION
① Press the desired camera number button you wish to display on the monitor.
② Press the D-ZOOM button. The indication screen appears on the main screen.
③ Press the , , , buttons to select the desired location.
④ Press the ESC button to exit this screen.
5.2.7 SCREEN SELECT(LV/PB) _8CH
During the playback, press the LV/PB button to convert the screen into real time display mode.
(Press this button again to return to the playback mode.)
5.2.8 SPOT MONITOR
Set up the desired mode in “SPOT” of “SCREEN MENU” before executing the SPOT mode.
5.2.8.1 MANUAL MODE
① Press the “SPOT” button on the front panel to toggle “SPOT” mode indicated on the main monitor.
② Press a camera button to display that camera on the spot monitor.
③ OSD of the selected channel will be indicated at the upper left of screen in live mode.
5.2.8.2 EVENT MODE
Press the “SPOT” button and the Spot monitor will display the channel which an event happened.
5.2.8.3 SEQUENCE MODE
Press the “SPOT” button and each channel and split channel will be displayed on the Spot monitor
in sequence.
** Please refer to 6.2.7 SPOT of SCREEN, page 44.
Spot Monitor
1 2
3 4
5 6
7 8
9 10
11 12 13 14 15 16
-
DIGITAL VIDEO RECORDER
27
OPERATION
5.2.9 COPY
Press the COPY button to copy the recorded images into other media and the COPY MENU screen
appears.
5.2.9.1 COPY
5.2.9.1-1 COPY TO EXTERNAL HDD
At the COPY menu,
① Move the cursor to COPY using the , buttons.
② Press the ENTER button and the following screen appears.
③ Select the desired MEDIA(HDD) (-), (+) buttons.
④ Move the cursor to HDD ID using the , buttons and select the desired HDD to copy among
HDD IDs using the (-), (+) buttons.
⑤ Move the cursor to the desired position of COPY START TIME/ COPY END TIME using
the , , , buttons and press the (-) or (+) button to set up the time to set up the COPY
START TIME and COPY END TIME.
** Scroll bar - It can operate with just Mouse click.
⑥ Press the ENTER button to copy.
NOTE
When the copy is in process, the copying status (ex. “COPY 30%” ) will be displayed on the right side of
the monitor.
You can search and playback the copied images in HDD with DVR itself
(Please refer to 5.1.4.4 FILE SEARCH, page 22.)
Loading...