How it Works
Rheem
Loading...
*HC-TST412MDMS Series
Quick Setup Manual
14 pgs6.67 Mb0

Rheem *HC-TST305UNMS Series, *HC-TST314UNMSSeries, *HC-TST412MDMS Series, *HC-TST422DFMS Series, *HC-TST501CMMS Series Quick Setup Manual

Download
Quick Set-up Thermostat Guide
Touchscreen Programmable Thermostats
*HC-TST305UNMS • *HC-TST314UNMS • *HC-TST412MDMS • *HC-TST422DFMS *HC-TST501CMMS (programming section only)
for MODELS:
Programming ....................................................................................................................................................................... 10
Operating ............................................................................................................................................................................. 11
Table of Contents
Quick Set-Up Guide for Touchscreen Thermostat 1
Installation Instructions for models:
*HC-TST305UNMS
*HC-TST314UNMS
*HC-TST412MDMS
*HC-TST422DFMS
*HC-TST501CMMS(programming section only)
Quick Set-Up Guide for Touchscreen Thermostats
+HDW 3XPS &RS\ 6\VWHP2Q &RRO6DYLQJV (0+HDW0RGH &DOO)RU6HUYLFH
'H+XP2Q
&KDQJH
$XWR
6FKHGXOH
+XPLGLW\
0RUQLQJ 'D\ (YHQLQJ 1LJKW )LOWHU 3DG 89/DPS
0RQWK <HDU
+XPLGLW\
2XWGRRU5HPRWH
+ROG8QWLO+XPLGLW\
NOTE:
These instructions are to be used for very basic installation only; they are intended to help the installer to
quickly set-up for basic operation and not set-up special features.
2 Quick Set-Up Guide for Touchscreen Thermostats
Quick Set-Up Guide for Touchscreen Thermostat 3
Installer, please perform the following steps.
1. Press the touch key.
2. Press and hold for 5 seconds the touch
key.
3. This displays Menu Reference number 1 from
the Installer Conguration Menu. The default is MS2 (Multi-stage selection). Use the or
touch keys to select to make a selection
of system type.
4. Press once to continue to Menu
Reference number 2 (GAS or ELE).
5. The default is GAS (gas furnace selection.
Use the or touch keys to select ELE (Electric furnace selection).
6. Press repeatedly to change to the
Remote sensor screen.
Menu Reference item no. 25 for:
*HC-TST314UNMS *HC-TST412MDMS *HC-TST422DFMS
Menu Reference item no. 27 for:
*HC-TST305UNMS
SYSTEM/REMOTE SENSOR CONFIGURATION
press repeatedly
or
default
default
Configuration Menu Reference no. 1
Configuration Menu Reference no. 2
or
or
or
or
Quick Set-Up Guide for Touchscreen Thermostat 3
7. The default is Remote OFF for (remote
sensor disabled). If no change is required,
then press
once to move to the next
Menu Reference number; otherwise, use the
or touch keys to select Remote On
(enables the remote sensor).
8. Press once to move to Menu sub-
selection for setting remote sensor location. The default is Remote In (Indoor remote
sensor). Use
or touch keys if Outdoor
Remote (Outdoor remote sensor) is desired.
9. Press once. If Remote In sub-selection
will change to choose local sensor. Default is Ls On – Local sensor enabled. Use
or
touch keys to change to LS OFF – Local
sensor disabled.
SYSTEM/REMOTE SENSOR CONFIGURATION
5HPRWH
2XWGRRU5HPRWH
Menu remote sensor has sub-selections that will appear if installer selects the Remote (On) setting.
Selecting this setting will enable Dual Fuel (dF) feature using outdoor remote sensor (see page 5)
Dual Fuel (dF) feature using software logic (see next page)
5HPRWH
5HPRWH
or
or
or
default
default
default
NOTES
A. Menu selection will skip Dual Fuel setup if Menu Reference number 1 was not changed to HP1 or HP2. If HP1 or HP2 was selected, then Menu selection
for Dual Fuel using software logic or Dual Fuel using outdoor remote sensor will appear on the display depending on the remote sensor selection.
B. Press
touch key to exit the Installer Conguration Menu.
4 Quick Set-Up Guide for Touchscreen Thermostats
Quick Set-Up Guide for Touchscreen Thermostat 5
Dual Fuel Using Software Logic (No outdoor sensor)
or
Configuration Menu
Reference no. 26
1. With Remote sensor OFF, press to display
Menu Reference item dF (Dual Fuel feature using software logic).
2. The default is dF OFF for Dual Fuel feature
disabled. Use the
or touch keys to
select dF On to enable the Dual Fuel feature using the software logic.
3. Press once to move to sub-selection: dF
05. Use the
or touch keys to set the
dual fuel setpoint.
4. Press once to set Cd (Compressor delay).
After the Auxiliary heat is turned on, the compressor shutdown is delayed for the time selected (default is 60 seconds).
DUAL FUEL CONFIGURATION
or
default
dF is congured
5. Press once to move to the next menu
item, dF is congured.
6. Press the touch key to exit the Installer
Conguration Menu.
Menu Reference item no. 26 for: *HC-TST314UNMS *HC-TST412MDMS *HC-TST422DFMS Menu Reference item no. 28 for:
*HC-TST305UNMS
Quick Set-Up Guide for Touchscreen Thermostat 5
Dual Fuel Using Outdoor Remote Sensor
Dual Fuel (dF) On
1. In Menu Reference number 26, use the or
touch keys to select Remote On. This
enables the remote sensor.
2. Press once to move to sub-selection:
Remote In. Use the or touch keys to select Outdoor Remote, this sets the sensor to outdoor.
3. Press to move to Menu Reference number
item dF.
4. The default is dF OFF. Use the or touch
keys to select dF On; this enables the dual fuel feature using the outdoor remote sensor.
5. Press once to move to sub-selection dF
35. Use the or touch keys to change
the dual fuel setpoint above or below 35oF; the thermostat will change the system over to gas heat from heat pump when the temperature falls below the setpoint.
DUAL FUEL CONFIGURATION
Menu Reference item no. 29 for:
*HC-TST305UNMS
or
default
dF is congured
6 Quick Set-Up Guide for Touchscreen Thermostats
Quick Set-Up Guide for Touchscreen Thermostat 7
6. Press once to set Cd (Compressor delay).
After the Auxiliary heat is turned on, the compressor shutdown is delayed for the time selected (default is 60 seconds).
7. Touch once to display Auxiliary
Off (AO). Using
or touch keys set the temperature to 80o. As long as the outdoor temperature is above the selected temperature, the auxiliary heat will not turn on.
8. Pressing once will enable the Blower
Balance Point (bP). Toggle
or to
set the bP to 80o, this feature de-energizes the DHM terminal to operate the blower at a slower speed for rst stage heat when the outdoor temperature is below the temperature selected.
9. Press once to move to next menu item.
Dual Fuel (dF) is congured.
10. Press the touch key to exit the Installer
Conguration Menu.
Dual Fuel (dF) OFF
1. With remote sensor enabled and dF(OFF),
pressing
once will change to Auxiliary
Off (AO). As long as the outdoor temperature is above the selected temperature, the
auxiliary heat will not turn on. Using
or
touch keys, set the temperature, default is 80o.
2. Pressing once will enable the Blower
Balance Point (bP). Toggle
or to set the bP. This feature de-energizes the DHM terminal to operate the blower at a slower speed for rst stage heat when the outdoor temperature is below the temperature selected. Default is 80o.
3. Press once to move to next menu item.
Dual Fuel (dF) is congured.
4. Press the touch key to exit the Installer
Conguration Menu.
DUAL FUEL CONFIGURATION
Quick Set-Up Guide for Touchscreen Thermostat 7
1. Press the touch key.
2. Press the touch key.
3. Press the touch key to select “Heat”
programming.
NOTE: You can switch to “Cool” mode by
pressing the System touch key at a time.
PROGRAMMING YOUR THERMOSTAT
press to adjust temperature
3.1. Press or touch keys to
change the temperature to your
selected temperature for the 1st heating period.
3.2. Press
or touch keys to adjust to start time for the period. The time will change in 15 minute increments.
4. Press the touch key to advance to the
next program period and repeat steps until all the program times and temperatures are set for all program periods on that day.
5. Press the touch key to advance
to the next program period and repeat steps until all the program times and temperatures are set for all program periods on that day.
8 Quick Set-Up Guide for Touchscreen Thermostats
PROGRAMMING YOUR THERMOSTAT
When programming your thermostat, you may copy the program from one day to another day or group of days using
the
key. In 7-day programming mode, a day can be copied to another day or all six other days. In 5/1/1 day programming mode the weekday (Mon­Fri) program can be copied into Sat and Sun or either Sat or Sun.
To Copy a Program from day to another
1. In Set Schedule mode, enter the program for
the day or select the day you wish to copy by pressing Advance key.
2. Press . The display will show “Copy”
next to the SYSTEM key and the day of the week that will be copied.
3. Press . The day being copied will be
indicated and the other days will be ashing.
4. If you wish to copy to all days skip to next step
or press
until the day you wish to
copy to is ashing.
5. Press . “Copy” will disappear, the day
you copied from will disappear and the day(s) you copied to will be on.
6. If you wish to copy this same program into
other day, press
and repeat steps 3, 4,
and 5.
7. Press touch key to return to normal
operation.
Quick Set-Up Guide for Touchscreen Thermostat 9
SET CURRENT TIME AND DAY
On Home Screen display, touch the key to display additional key choices.
1. Touch once to display hour and AM or
PM designation in clock display.
2. Touch either the or key until you reach
the correct hour and AM or PM designation.
Then touch
again to display minutes only
in clock display.
3. Touch and hold either the or keys until
you reach the correct minutes. Then touch
once again to display the day of the
week.
4. Touch either the or key until you reach
the correct day.
Touch
to save the Time and Day settings
and return to the Home Screen display.
2
1
2
1
2
1
10 Quick Set-Up Guide for Touchscreen Thermostats
OPERATING
Touch the SYSTEM key to select:
Cool:
Thermostat controls only the cooling system.
Off:
Heating and Cooling systems are off.
Heat:
Thermostat controls only the heating system.
Em:
Thermostat controls emergency heating only.
Auto:
Auto Changeover is used where both heating and
cooling may be required during the same day. Auto allows the thermostat to automatically select heating or cooling depending on the indoor temperature and the selected heat and cool setpoints. This thermostat will not allow you to program a conict between Heating and Cooling setpoints.
Choose the System Setting (Cool, Off, Heat, Em, Auto)
Quick Set-Up Guide for Touchscreen Thermostat 11
Factory Pre-Programmed heating and cooling Schedule for all days of the week
Program Wake Up
(Morning)
Leave For Work
(Day)
Return Home
(Evening)
Go To Bed
(Night)
Heating Program
6:00 AM 70
o
F 8:00 AM 62oF 5:00 PM 70oF 10:00 PM 62oF
Cooling Program
6:00 AM 75
o
F 8:00 AM 83oF 5:00 PM 75oF 10:00 PM 78oF
This touchscreen thermostat is programmed with the energy saving settings shown in the table below for all days of the week. If this program suits
your customer’s needs, simply touch the
key.
OPERATING
Energy Saving Factory Pre-Program
R-4316
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use