![](/html/ec/ec59/ec59b1f7bc10a4944bfbfc8838ba864764e8b6bc98cae61fc6e575ad2c02f9df/bg1.png)
120, 208, 240,
277 and 480
voltages
P oint-Of-UseElectric Commercial Water Heaters
Available in Sizes Ranging From 2-1/2 – 30 Gallon Tank-Type Models
1440 Watts thru 6000 Watts
Rheem-Ruud point-of-use electric commercial water heaters are designed to
provide hot water at the consumption point, eliminating costly temperature
loss in long piping runs.Well suited for a wide variety of applications, point-ofuse heaters are small enough for installation in limited spaces under counters, mop sinks, cabinets, or any remote area where modest quantities of hot
water are required.They are ideally suited for applications in retail stores,
public restrooms, office washrooms, kitchen and mop or bar sinks.
Construction Features:
•
Long life tank design –
proprietary steel formulation with a
unique coat of high temperature
porcelain enamel to maximize
corrosion resistance resulting in a
superior tank design. A patented
R-Tech anode rod provides
advanced technology; equalizing
aggressive water action while
prolonging the effective life of
the anode rod and in turn the
life of the tank.
•
Long life heating elements –
Our patented resistor elements
are designed with a specially
treated, double layer of magnesium oxide and copper to
resist corrosion.
•
Efficient design –
Rigid polyurethane foam insulation
provides superior insulating
qualities resulting in reduced
operating costs.
•
Optional wall mounting kit –
The wall mounting kit provides an
easy way to mount the unit off the
floor, out of the way for more useable floor space in a small area.
Each kit is designed to be used on
walls with 16" stud centers.All
necessary par ts are included in
this easy to install kit. (Note: The
2-1/2 gallon model comes standard with a wall mounting kit.)
•
Automatic temperature
control –
A surface mounted thermostat
automatically cycles on and off to
maintain the water temperature at
a desired preset level.
•
Temperature limiting control –
Automatically and safely cuts off
the power in the unlikely event that
the water temperature exceeds
190°F.
•
Temperature and pressure
relief valve –
AGA/ASME rated and factory
installed.
Certifications and Ratings:
• Efficiency – these models meet or exceed thermal efficiency and standby
loss requirements of current ASHRAE standards. (Part of the Federally
mandated Energy Policy Act (EPact)). Also exceeds energy efficiency codes
of all states including California Energy Commission (CEC).
• Safety and construction – these products are design certified by
Underwriters Laboratories (UL) to meet UL standard 174 as electric storage
tank water heaters.All models are North Carolina Code compliant.
CERTIFIED FOR A 150 PSI MAXIMUM WORKING PRESSURE.
Continued on reverse.
N
T
E
L
D
A
N
B
E
O
P
R
E
A
D
T
N
O
I
N
A
•
T
E
S
R
Y
•
®
Y
T
T
E
I
F
N
A
G
S
F
C
O
I
L
R
B
P
U
![](/html/ec/ec59/ec59b1f7bc10a4944bfbfc8838ba864764e8b6bc98cae61fc6e575ad2c02f9df/bg2.png)
Rheem Water Heating • 101 Bell Road, Montgomery, Alabama 36117-4305 • www.rheem.com
Rheem Canada Ltd./Ltée,128 Barton Street West, Hamilton, Ontario L8N 3P3
PRINTED IN U.S.A 10/06 WP FORM NO. RR102CE-4 Rev. 9
In keeping with its policy of continuous progress and product improvement, Rheem-Ruud reserves the right to make changes without notice .
Recommended Specifications:
Water heater(s) shall be model ______________, manufactured by RHEEM-RUUD, having electrical input of
__________ kW and a recovery rate of _____________
GPH at a 100°F temperature rise.Water heater(s) shall
have a storage capacity of ________ gallons.Water
heater(s) shall have the UL seal of certification and be
factory equipped with an AGA /ASME rated temperature
and pressure relief valve.Tank(s) inter ior shall be coated
with a high temperature porcelain enamel and furnished
with an R-Tech resistored magnesium anode rod rigidly
supported. Water heater(s) shall meet or exceed the
energy factor requirements of ASHRAE.Tanks shall have
a working pressure rating of 150 psi, and shall be completely assembled.Water heater(s) shall be equipped
with a copper, resistored, “screw-in” type element.Tank
shall be insulated with rigid polyurethane foam
insulation.Water heater(s) shall be equipped with a
surface mounted thermostat with an integral, manual
reset, high limit control.Water heater(s) shall be covered
by a three year limited warranty against tank leaks.
Limited Warranty:
This product features a three year limited warranty
against tank leaks. Please refer to Commercial Warranty
Information brochure for complete warranty infor mation.
DIMENSIONAL INFORMATION (All dimensions shown in English and Metric)
TANK
APPROXIMATE
MODEL MIN MAX
CAPACITY
ABCD
E
SHIPPING WEIGHT
NUMBER WATTS WATTS
GALLONS LITERS
inches mm inches mm inches mm inches mm inches mm LBS. KGS.
EGSP2 1,440 1,500 2.5 9 14 356 9-3/4 248 -——-———— 18 8
EGSP6 1,500 6,000 6 23 15-1/8 384 15-3/4 400 12-5/8 321 11-5/8 295 4-1/4 108 41 19
EGSP10 1,500 6,000 10 38 22-7/8 581 15-3/4 400 20-3/8 518 19-3/8 492 4-1/4 108 53 24
EGSP15 1,500 6,000 15 57 24-1/4 616 17-3/4 451 21-7/8 556 19-3/8 492 4-5/8 117 65 29
EGSP20 1,500 6,000 19.9 75 25-1/8 638 19-3/4 502 22-5/8 575 19-3/8 492 5-1/8 130 76 34
EGSP30 1,500 6,000 30 114 30 762 21-3/4 533 23 584 23 584 2-3/4 70 115 52
ELECTRICAL CHARACTERISTICS
ELEMENT SINGLE PHASE OPERATION ONLY – AMPS
WATTA GE 120 V 208 V 240 V 277 V 480 V
1,440 12.0 NA NA NA NA
1,500 12.5 7.2 6.3 N/A N/A
2,000 16.7 9.6 8.3 7.2 4.2
2,500 20.8 12.0 10.4 NA NA
3,000 25.0 14.4 12.5 10.8 6.3
4,500 NA 21.6 18.8 16.2 9.4
6,000 NA 28.8 25.0 21.7 12.5
All models employ 1 heating element resulting in a 2-wire outlet
(single phase) electrical configuration.
RECOVERY CAPACITIES
Recovery in U.S. Gallons/Hr. (GPH) and Liters/Hr. (LPH)
at Various Temperature Rises
40°F 60°F80°F 100°F 120°F
ELEMENT (22°C) (33°C) (45°C) (56°C) (67°C)
WATTAGE
GPH LPH GPH LPH GPH LPH GPH LPH GPH LPH
1,440 15 55 10 37 7 28 6 22 5 18
1,500
15 58 10 38 8 29 6 23 5 19
2,000
20 77 14 51 10 38 8 31 7 26
2,500 25 96 17 64 13 48 10 38 8 32
3,000
30 115 20 77 15 58 12 46 10 38
4,500 46 173 30 115 23 86 18 69 15 58
6,000
61 230 41 153 30 115 24 92 20 77
Water
Temperature
Ratings:
Thermostat
Type:
Surface Mounted
Minimum
Temperature:
110
°F (43.3°C)
Maximum
Temperature:
170
°F (76.7°C)
High Temperature
Limit:
190
°F (87.8°C)
MODELS:
EGSP6
EGSP10
EGSP15
EGSP20
EGSP30
Water
Connections
3/4" NPT
MODEL:
EGSP2
Water
Connections
1/2" NPT
NOTE: Basic model numbers are listed.When ordering, specify electrical input and kW to determine specific model number.
PRODUCT AVAILABILITY
ELEMENT SINGLE PHASE OPERATION ONLY
WATTA GE 120 V 208 V 240 V 277 V 480 V
1,440 Y** NA NA NA NA
1,500 Y Y Y** N/A N/A
2,000 Y Y Y Y Y
2,500 Y Y Y NA NA
3,000 Y Y Y Y Y
4,500 NA Y Y* Y* Y*
6,000 NA Y Y Y Y
*Not available in EGSP6 & EGSP10
**EGSP2 available only in these configurations
HOT WATER
CONNECTION
COLD WATER
CONNECTION
3/4" T&P
3-1/2" (89mm)
HOT
WATER
OUTLET
B
C
D
A
E
COLD
WATER
INLET
3/4" T&P