RF-Link WHD-5001 User Manual
Contents
1.Important Safety Information....................................... 1
2.Package Content........................................................2
3.Panel Control And Function......................................... 3
4.Setup Guide...............................................................4
5.Optimizing System Performance 5..................................
1.Important Safety Information
Model: WHD-5001
Wireless HD A/V sender
To prevent fire or shock hazard, do not expose this product to rain and
moisture. For example: do not use near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or nearby a swimming pool. To
avo id elec tric sho ck, do not t ake apar t t his pro duct, p rovid ed as an
accessory. This product should be operated only under power supply.
Do not overload wall outlets and extension outlets as this can result in
the risk of f ire or elect ric shock.
FCC Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note:
This equipment has been tested and found to comply with the limits regulated
by FCC and CE. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to
radio communications. The change or modifcations not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment. To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements
and void user’s authority to operate the device.
2.Package Contents
Check to make sure that all units shown as below are enclosed.
If something missed, please contact your dealer.
1. 5.0GHz Transmitter x1
UHF:433.92MHz
2. 5.0GHz Receiver x1
1
2.Package Contents3.Panel Control and Function
List of functions
Transm itter unit
Receive r unit
1
1
2
3. IR Blaster x1
5.Power Adapters x2
USA Type
4. HDMI Cable x1
6. Antenna x6
2
1.
Dipole antenna
2.
Power/Link LED indicator
3.
IR windows
4.
On/Off switch
5.
IR Blaster jack(Transmitter only)
6.
HDMI connector
7.
Power adapter jack
3
4 5 6 7
2
3
2.Package Contents4.Setup Guide
2.Package Contents5.Optimizing System Performance
Transmitter
1. Connect HDMI cable
between transmitter and
your source device (Set top
box, Blue Ray DVD
player....).
2. Connect USB plug of power
adapter to transmitter, then
plug in power to an outlet.
3. Place IR Blaster in close
proximity to IR sensor of
your source device.
Receiver
1. Connect HDMI cable
between receiver and your
receiving device (TV,
Monitor, Speaker....).
2. Connect USB plug of power
adapter to receiver, then
plug in power to an outlet.
IR Blas ter
Tra ns mi tt er (T X)
To AV Equipment
Receiver(RX)
To TV
Like all wirel ess e lectronic product s, the syste m's
performance may be affected by any obstruction
between transmitter and receiver. Please follow below
recommendations in order to create an optimal
environment, and a proper placement of the system will
ensure a strong connection for superior performance.
1. Avoi d m ul ti pl e s y st em s i n t h e s a me r oo m i f p os si bl e.
2. Avo i d having 5 . 0 GHz WLAN or cordle s s phone i n the
same room if possible.
3. Do not place either transmitter or receiver on a metallic
rack.
4. Place transmitter as high as possible.
5 . M ax im um op er at in g d is ta nc e i s a pp ro xi ma t el y 2 0
m et e rs or 65 fe et wi t h c lea r l i ne of si ght , a n d a ctu al
performance may vary depends on user’s environment.
6. Pl eas e k e ep in mi n d t he s yst em m ay be aff ect e d b y
interference from other wireless products as well as ,
signal attenuation (weakening) due to the proximity
o f c ert ain ob jec t s/ m ate ria ls s uch a s wa lls fl oor s, ,
doors and other construction materials that contain ,
m et a l. L arg e ho me a ppl ian ces m ay a lso aff e ct
p er f or man ce s uch as r efr ige rat ors w a sh e rs a nd ,
dryers.
4
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should
not be treated as household or general waste. It
should be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.
5
TTD-B50 01T
TTD-B50 01R
6
408-000 660-00
Loading...