User's Manual
HDMI Extender over CAT5
with IR, Ethernet & Serial Extending
RoHS
PP5-HEM257Z-000
Package Contents
● Transmitter Unit x 1
● Receiver Unit x 1
● Power Adapter Set x 1
Power Adapter with necessary AC Cord
or
Plug-in Power Adapter
● User’s Manual x 1
● Foot Pad Set x 2
● CAT5 Cable x 1
● Grounding Wire x 2
Optional:
● IR External Sensor Kit
● Serial Cable ● HDMI Cable
Connection Pattern
Operation
The LEDs on the Extender Units show the real-time status indicating the
linking and com munication between th e Transmitter Unit and Receive r
Unit. Users can identify the present status through the LED indicat or on
the top.
The q uality of the ou tput signal will depend lar gely upon the qu ality of
video source, cable and display device used. Low quality cables degrade
output signal causing elevated noise levels. Please use the proper cable
and mak e sure t he display device is capable of handling the resolution
and refresh rate selected.
NOTE:
1. The system will disable the video outp ut signal when it detects nonHDCP compliant display(s) on playing the HDCP video source. All the
connected output displays MUST be HDCP compliant, when the video
source is HDCP compliant.
2. If there’ s no sign al de tected from HDM I por t, t he ba ud r ate will
automatically speed down to 9,600 bps.
Specications
Users can connect the video source to t he Trans mitter Unit, connect
the monitor to the Re ceiver Unit. Connect to Ethernet device s to the
Transmitter and the Re ceiver Units (LAN ports) and use CAT5e/6 cable
(EIA / TIA 568B industry standard compliant) for the connection between
the Transmitter (Link Port) and Receiver Unit (Link Port) . After all device
connec tions a re com pleted, connect the provided power cord into an
appro priate power sour ce an d plu g the oppo site end i nto the p ower
connector* on the Unit to power up.
CAUTION: The CAT5e/6 cables that connect the Transmitter and Receiver
Units car ry e lectric al c urrent and shou ld no t be plu gged in t o ot her
devices, as they may cause damage. We strongly recommend marking the
CAT5e/6 cables you are using with this product at both locations for easy
identication.
The nal specication is the actual product based.
Features and functions may be added or changed
after the man ual was writte n. P lease visi t ou r
website to download the latest version of manual
for reference.
◘
◘
● Prior to installation, ensure to power off all devices that will be
connected to this system.
● Ensure that all devices you will connect are properly grounded.
● Place cables away from uorescent lights, air conditioners, and
machines that are likely to generate electrical noise.
Rextron
Features
● Compatible with HDBaseTTM PoH standard
● Send HDMI signal to multimedia display over CAT5e/6 cable of up to
100 meters
● Uses HDBaseTTM Technology
● Low cost standard CAT5e/6 LAN cable; advanced and inexpensive
all-in-one connectivity technology
● HDCP compliant and Blu-ray ready
● Support Deep Color, HD-3D video and HD Audio formats
● Support resolution up to Full HD 1080p / 2048 x 1152
● Bi-directional LAN & Serial
● Compact size; easy to set up; simple to install
● I deal for h ospitali ty (h otels, confer ence rooms), digit al si gnage
(ai rpor ts, shop ping ma lls) , s urve illan ce came ras, wh ole- home
networking and point-to-point consumer applications
Exclusive 5PlayTM Feature
● Transmit full uncompressed HD video and audio over CAT5e/6 cable
● Support LPCM 7.1 Audio, Dolby® TrueHD and DTS-HD Master
Audio™ pass-through
● 100BaseT Ethernet Pass-Thru; simultaneously distribute HDMI and
Ethernet streaming video from source to display
● Multiple interface options allow controlling the unit by Hotkey control
and Serial control
● Transmitter Unit deliver DC power to Receiver Unit over CAT5e/6
cable
Installation Product Description
EVBMN-M210
(EVBMN-210L + EVBMN-210R)
Rear Panel
Front Panel
La Ls
Tx / Rx
La LAN LED Yellow: LAN status (Data communication)
Ls Status LED
[Tx] Blue: Link status; Green: Power on;
Flashing Blue+Green: Power-saving mode
[Rx] Blue: Link status; Red: Power on;
Flashing Blue+Red: Power-saving mode
T1 R1
RJ-45
Connector
Connect to Ethernet devices
T2 R2
HDMI
Connector
[T2] Connect to an HDMI video source
[R2] Connect to an HDMI disply
T3 R3
RJ-45
Connector
Use CAT5e/6 for connection between two units.
T4 R4 Serial Port
[T4] (DCE) Connect to a computer
[R4] (DTE) Connect to a serial device
T5 R5 Slide Switch* Please set on the same position for Tx and Rx
IR1(in)
IR Remote
Jack
Connect to an IR Receiver
IR1(out) Connect to an IR Transceiver
IR2(in) Connect to an IR Receiver
IR2(out) Connect to an IR Transceiver
P Power Supply** Apply power to the unit.
*Please set both of slide switches on the same position to reach the goal.
Normal: The extension distance of HDMI signal over CAT5/6 is up to 100M
for 1080p and 70M for 4Kx2K.
Long Reach: The extension distance of HDMI signal over CAT5/6 will
be increased up to 150M for 1080p, but the unit can not transmit 4Kx2K
resolution.
Auto power saving: The extension distance of HDMI signal over CAT5/6
is the same as "Nornal", but the unit can automatically save energy for
increasing efciency use.
**Power over HDBaseT
TM
(PoH): Only Transmitter Unit is required to
connect to power adapter and power the entire system. The PoE standard
is based on the IEEE 802.3at standard.
Cabling Requirements
HDM I t ransm issio n r unnin g a long th e E thern et cabli ng is parti cula rly
susceptib le to EMI (elec tro magne tic inter ference) o r RFI (radio f requency
interfere nce). It can be caused by being in close to fluor escent l ighting o r
power cabling. Th e following are s ome conside rations tha t you should pay
attention to.
1. Place cables away from uorescent lights, air conditioners, and machines
that are likely to generate electrical noise.
2. The shielded ca bles (FTP, STP) are suggested for they can reduc e the
interference, and work better to EMI or RFI than UTP cables.
3. For superior video quality, unbu ndled cabl es work better than bundl ed
ones. Bundled cable of greater than 3 ft. diameter will have minor effect on
the cable length.
4. The solid cable will work better than stranded cable. It may shorten the
transmission distance if you use stranded cabling or other cables thinner
than 24AWG . Tha t is , so lid c able of larger than 24AWG is stro ngly
suggested. Additionally, CAT6 is more recommended.
5. Jo ined cables can resul t in signa l los s an d sho rtening tran smissio n
distance. Therefore, for the optimal transmission distance, we recommend
using only o ne piece of cable (w ithout a ny immedi ate join ts) betw een
transmitter and receiver units.
Other Notices
1. Due to EMI or RFI, some certain brands/type s of displays, like monitors
and TVs, may result fuzzy or snowing on screens. In this case, please try
to restart the displays.
2. As the system transmits massive data, temperature rises on the unit is a
normal ph enomenon, so please do not open any components inside by
yourself.
3. The unit is a sea led structure ; should not be tampered w ith by anyone
other than registered installer.
EVBMN-M210
Transmitter Unit (Tx) Receiver Unit (Rx)
EVBMN-210L EVBMN-210R
Input → Output HDMI → RJ-45 RJ-45 → HDMI
Power over HDBaseT
TM
**
PSE (
Power Source
Equipment)
PD (
Powered Device)
LED
Status LED Dual Color x 1 Dual Color x 1
LAN LED Single Color x 3 Single Color x 3
Video Resolution (Max.) UHD (3840 x 2160 @ 30Hz)
Extension Distance*
Full HD 1920 x 1080 @ 100M
UHD 3840 x 2160 @ 70M
Ethernet Port
RJ-45 x 3 RJ-45 x 3
10/100 Mbps
Serial Port
DCE, DB9-F DTE, DB9-M
115kbps (max.)
IR Extension
x 1, IR Transceiver
x 1, IR Receiver
x 1, IR Transceiver
x 1, IR Receiver
Slide Switch Auto Power Saving / Normal / Long Reach
Power Supply DC 12V
Enclosure Metal
H x W x D (mm) 140 x 85 x 34
Weight (g) 1195 (each unit)
*Above video r esolution and exten sion dist ance are based on a single C AT5e/6
24AWG solid cable without cascade. STP cabling is recommended for environments
with high EMI or RFI. For the best perform ance results, using stranded cabling or
other thinner cables, and coiling of excess cable lengths should be avoided.
NOTE:
Rextron EVBMN-M210, Transmitter Unit (PSE) and Receiver Unit (PD) is compatible
with HDB aseT
TM
PoH standard. It only need to connect powe r adapter to Tx and
it will automatically transmit power to Rx. If user may want to use other brand's Tx
or Rx, please make sure whether it is compatible with HDBaseTTM PoH standard.
Moreover, Transmitter Unit should be PSE and Receiver Unit should be PD, or it may
not work. It is highly recommended use Rextron's Tx connecting to Rextron's Rx for
optimal transmission quality.
T4P
T1
T2T3
Grounding
IR1(in)
Tx
IR2(out)
T5
Grounding
R1
R2R3
R4P
Rx
IR1(out)IR2(in)
R5
(Power over HDBaseTTM)
CAT5 100M
IR Transceiver
Switch Hub
To Serial Terminal
IR Receiver
ADSL
Serial Devices
Tx
Rx
IR Transceiver
IR Receiver
DC 12V
DC 12V
(optional)
(PD)
(PSE)
Power over HDBaseT
TM
Loading...