REX N30P, N30S, N42P, N42S, N67P Operating Instructions Manual

Operating Instructions

4V440-E2

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Specifications

Instructions

Coated and Nude Copper Pipes

External Diam. 5 - 34 mm

350g

φ32

625ZZ

424237

Blade for Thin wall Stainless Steel Pipes

(Code No.424233, 424284)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

・

・

・

・
・

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For Coated and Nude Copper Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Fig.1

Fig.2

Fig.3

Rotate

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

RB Tube Cutter
Model N30P

Code No.

427830

Operating Instructions

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Specifications

Instructions

Thin wall Stainless Steel Pipes

External Diam. 5 - 34 mm

350g

φ30

625ZZ

424233, 424284

Blade for Coated and Nude Copper pipes

(Code No. 424237)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

・

・

・

・
・

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For Thin wall Stainless Steel Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Fig.1

Fig.2

Fig.3

Rotate

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

4V410-E1

RB Tube Cutter
Model N30S

Code No.

427630

1304D01000

0808D01000

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Instructions

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

・

・

・

・
・

Fig.1

Fig.2

Fig.3

Rotate

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

Operating Instructions

4V420-E1
0901D01000

RB Tube Cutter
Model N42S

Code No.

427642

Specifications

Thin wall Stainless Steel Pipes

External Diam. 6 - 42 mm

400g

φ30

625ZZ

424233, 424284

Blade for Coated and Nude Copper pipes

(Code No. 424237)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Specifications

Coated and Nude Copper Pipes

External Diam. 6 - 42 mm

400g

φ32

625ZZ

424237

Blade for Thin wall Stainless Steel Pipes

(Code No.424233, 424284)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

4V450-E3
1304D01000

Operating Instructions

Instructions

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For Coated and Nude Copper Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

・

・

・

・
・

Fig.1

Fig.3

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

Fig.2

Rotate

RB Tube Cutter
Model N42P

Code No.

427842

For Thin wall Stainless Steel Pipes