REX N30P, N30S, N42P, N42S, N67P Operating Instructions Manual

Operating Instructions

4V440-E2

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Specifications

Instructions

Coated and Nude Copper Pipes

External Diam. 5 - 34 mm

350g

φ32

625ZZ

424237

Blade for Thin wall Stainless Steel Pipes

(Code No.424233, 424284)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

・

・

・

・
・

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For Coated and Nude Copper Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Fig.1

Fig.2

Fig.3

Rotate

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

RB Tube Cutter
Model N30P

Code No.

427830

Operating Instructions

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Specifications

Instructions

Thin wall Stainless Steel Pipes

External Diam. 5 - 34 mm

350g

φ30

625ZZ

424233, 424284

Blade for Coated and Nude Copper pipes

(Code No. 424237)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

・

・

・

・
・

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For Thin wall Stainless Steel Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Fig.1

Fig.2

Fig.3

Rotate

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

4V410-E1

RB Tube Cutter
Model N30S

Code No.

427630

1304D01000

0808D01000

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Instructions

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

・

・

・

・
・

Fig.1

Fig.2

Fig.3

Rotate

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

Operating Instructions

4V420-E1
0901D01000

RB Tube Cutter
Model N42S

Code No.

427642

Specifications

Thin wall Stainless Steel Pipes

External Diam. 6 - 42 mm

400g

φ30

625ZZ

424233, 424284

Blade for Coated and Nude Copper pipes

(Code No. 424237)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

Specifications

Coated and Nude Copper Pipes

External Diam. 6 - 42 mm

400g

φ32

625ZZ

424237

Blade for Thin wall Stainless Steel Pipes

(Code No.424233, 424284)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

4V450-E3
1304D01000

Operating Instructions

Instructions

①

Pipe

Grip

Rollers

Place the pipe on the cutter between
the rollers and the blade as shown in
Fig. 1. When doing so, make sure the
end of the pipe protrudes further than
the width of the rollers. Once the blade
engages the pipe, turn the grip clockwise
again

1

/4

of a turn.

Rotate the cutter back and forth 2 or 3
times through 90゜ (see Fig.4 on reverse
side) then fully one time to make a cutting
guideline.

Then turn the grip slowly, (

1

/8

of a turn for
every 3 or 4 rotations of the cutter) and
keep rotating the cutter as you gradually
cut deeper into the pipe.

Avoid cutting too quickly or the pipe may
become distorted and the life of the blades
reduced.
By attaching a special blade (sold separately)
you can also cut copper (annealed or
unannealed) and brass pipes.

・

・

Blade

For Coated and Nude Copper Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these
instructions in a safe place so that you can refer to them at any time.

Use the cutter only for the types of tubes described in these
instructions. Use with other pipes, or for purposes other than the
intended use, may result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong,
do not use until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do

so could result in the bearings becoming rusty and malfunctioning.

・

・

・

・
・

Fig.1

Fig.3

Turn grip approx.1/8 of 3 or 4 turn

Rotate cutter once

Turn

Fig.2

Rotate

RB Tube Cutter
Model N42P

Code No.

427842

For Thin wall Stainless Steel Pipes

Code No.

427667

RB Tube Cutter
Model N67S

①

Push in

Fig.4

②

Pipe

Grip

Blade

Turn

Rollers

Place the pipe on the cutter as shown in Fig.1,
making sure the end of the pipe protrudes further
than the width of the rollers. Push in the grip until
the rollers and blade lightly contact the pipe.

At that point, turn the grip clockwise again 1/4
of a turn.Rotate the cutter back and forth 2 or
3 times through 90゜(see Fig. 5 on reverse side)
then once more through one complete rotation
to make a cutting guideline.

Then turn the grip slowly, (1/8 of a turn for every
3 or 4 rotations of the cutter) and keep rotating the
cutter as you gradually cut deeper into the pipe.

Avoid cutting too quickly or the pipe may become
distorted and the life of the blades reduced.

Press the lever on the underside of the cutter
(see Fig. 4) to release the blade.

When you release the blade, the grip springs
back quite forcefully.
To avoid injury, hold the cutter away from your
face or other parts of your body.

By attaching a special blade (sold separately)
you can also cut copper

(annealed or unannealed)

and brass pipes

Rotate

Fig.2

Springs out

Specifications

Instructions

Thin Wall Stainless Steel Pipes

External Diam. 12 - 67 mm

870g

φ30

625ZZ

424233, 424284

Blade for Coated and Nude Copper Pipes
(Code No. 424237)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

Use the cutter only for the types of tubes described in these instructions.
Use with other pipes, or for purposes other than the intended use, may
result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong, do not use
until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do so could

result in the bearings becoming rusty and malfunctioning.

・

・

・

・
・

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

For Thin wall Stainless Steel Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these instructions
in a safe place so that you can refer to them at any time.

・

・

Fig.3

Turn grip approx.1/8 of a 3 or 4 turn

Rotate cutter fully once

Press

Fig.1

Operating Instructions

4V430-E2

①

Push in

Fig.4

②

Pipe

Grip

Blade

Turn

Rollers

Place the pipe on the cutter as shown in Fig.1,
making sure the end of the pipe protrudes further
than the width of the rollers. Push in the grip until
the rollers and blade lightly contact the pipe.

At that point, turn the grip clockwise again 1/4
of a turn.Rotate the cutter back and forth 2 or
3 times through 90゜(see Fig. 5 on reverse side)
then once more through one complete rotation
to make a cutting guideline.

Then turn the grip slowly, (1/8 of a turn for every
3 or 4 rotations of the cutter) and keep rotating the
cutter as you gradually cut deeper into the pipe.

Avoid cutting too quickly or the pipe may become
distorted and the life of the blades reduced.

Press the lever on the underside of the cutter
(see Fig. 4) to release the blade.

When you release the blade, the grip springs
back quite forcefully.
To avoid injury, hold the cutter away from your
face or other parts of your body.

By attaching a special blade (sold separately)
you can also cut copper

(annealed or unannealed)

and brass pipes

Rotate

Fig.2

Springs out

Specifications

Instructions

Coated and Nude Copper Pipes

External Diam. 12 ~ 67 mm

870g

φ32

625ZZ

424237

Blade for Thin Wall Stainless Steel Pipes
(Code No.424233, 424284)

Application

Cutting capacity

Weight (main unit)

Blade diameter

Rollers

Spare Blade Code No.

Optional Extras

Use the cutter only for the types of tubes described in these instructions.
Use with other pipes, or for purposes other than the intended use, may
result in an accident or damage to the cutter.

Always inspect the cutter before use. If you find anything wrong, do not use
until repairs have been made.

When cutting pipes, make sure the blade doesn't touch your hand.
Never place your fingers between the blade and the pipe.

Avoid dropping the cutter either when using or carrying it.
Be sure to remove any water or flux from the cutter. Failure to do so could

result in the bearings becoming rusty and malfunctioning.

・

・

・

・
・

1-9-3, Hishiya-Higashi, Higashi-Osaka 578-0948 Japan

Tel. [phone] Fax [phone]

www.rexind.co.jp

For Coated and Nude Copper Pipes

For safe, efficient use, read these instructions carefully before use.
Use the device correctly and for its intended use only. Keep these instructions
in a safe place so that you can refer to them at any time.

・

・

Fig.

3

Tur

n

gr

ip

app

r

o

x.

1

/

8

o

f

a

3

or

4

t

u

r

n

Rotate

c

ut

ter

fully

o

nce

Press

Fig.1

Operating Instructions

4V460-E1

RB Tube Cutter
Model N67P

Code No.

427867

0808D01000

1107D01000