Page 1
SSP6 Multiducer
®
REVOLUTION ACOUSTICS SSP6 MULTIDUCER™
The SSP6™ Multiducer™ (multifunctional transducer)
miraculously transforms nearly any panel structure into
an audio speaker. Revolutionary thinking has created
one of the most compact and powerful “invisible” audio
systems available today. Embedding the SSP6 Multiducer™ into walls, ceilings, glass, furniture, vehicles and
other products transforms non-acoustic materials and
devices into high fidelity audio speakers. Using an
entirely different subset of acoustical physics, the SPP6
is able to “ergonomically” project sound unlike any other
conventional speaker filling the space with rich audio
content in ways never before tought possible.
Fast and easy installation using the Rev-Loc™ mounting
plate (included). Water and dust resistant coupled with
solid-state construction for consistent and reliable
service over many years. A true lifestyle solution, the
SSP6 Multiducer™ delivers true full frequency audio,
ease of installation, and value unlike anything in its class
or all others. It is simply magical. Invisible audio, which is,
literally out of sight with performance to match.
TECHNICAL SPECIFICATION
• Next generation and new level of sophistication in invis-
ible embedded audio technology
• SSP6 with new Rev-Loc™ universal screw on mounting
plate for unparalleled ease of installation to virtually all
substrates in less then 5 minutes.
• Incredible class leading acoustic fidelity while driving all
materials including glass, drywall, wood, fiberglass,
metal, or….
• Highest power density, best sounding transducers available using high energy neodymium magnet structures
• Proprietary cooling technologies for better efficiency
and reliability
• Frequency range full bandwidth: (unequalized) 45Hz –
20KHz (recommend high pass filter at 60Hz)
• Subwoofer not required
• Compact 2.7” Ø X 2.1” high (69mmØ X 53.5mm high)
• Weight (Individual): 0.68 Kg / 1.5 Lbs.
• Impedance: 6Ω
• Mounted in free air (not enclosed) at 20C ambient:
Maximum long-term-average signal level 15.5 Vrms, high
passed at 60Hz 12dB/octave
• Measured maximum average power 40W.
• Derate amp for higher ambient or enclosure:
Enclosed transducer at 22C ambient
• Maximum long-term-average signal level 9.4 Vrms
high passed at 60Hz 12dB/octave,
• Measured maximum average power 14.7W.
• ANSI/CEA 426B recommend amplifier power 80W
• IP65 Ingress protection certified - water and dust proof
• Transducer heat test: fully enclosed passes EIA 426B
at 9.4V(nominal power rating of 30W) 8 hour test 23C
ambient
• Packaging: 2 per box
• Package weight: 1.58 Kg / 3.5 Lbs.
INSTALLATION INSTRUCTIONS (please read)
Your SSP6 Multiducers™ can transform many materials
into high fidelity audio emitters. Drywall panels (plaster
board), glass panels, wood, MDF, fiberglass, and even
some steel sheet can become large acoustic radiators
using your SSP6 Multiducers™. If possible, pre-test
your installation by handholding a Multiducer™ to the
material in which you wish to install to and sound-check.
Check surrounding surfaces and material as well and
install to the most desirable surface. The SSP6 Multiducers™ will not function on brick, stone or cinderblock,
or materials lamented to them. Walls, wood floors, quality build and framed windows, fiberglass, and some
furniture are typically good choices.
The Rev-Loc™ mounting plate ensures a fast and easy
installation. The Rev-Loc™ must always be firmly
glued to the material being driven by the SSP6 Multiducers™. Quick setting glue is to be applied essentially
over the entire bottom surface of the Rev-Loc™. Then
firmly press the Rev-Loc™ to the surface and let glue
set before screwing on SSP6 Multiducer™. Exceptions
are intra-wall retrofits where the Rev-Loc™ and SSP6
Multiducer™ are typically installed together during the
gluing process.
Glues
One of 3 glues will cover all installations. In ALL cases,
once glues are set and hardened simply screw on the
SSP6 giving it a final screw torque by twisting the
black metal base of the Multiducer™ only hand tight,
not the plastic housing. This will activate the Loctite®
thread locking glue on the Rev-loc™ stud portion.
INSTALLATION MANUAL
Page 2
PATENTED and numerous patents pending
© REVOLUTION ACOUSTICS LTD. All rights reserved
Revolution Acoustics®, SSP6™, Multiducer™ as well as all
graphical trademarks herein are property of Revolution
Acoustics Limited.
Additonnal information, including warranty see:
revolutionacoustics.com
GLASS OR OTHER SMOOTH NONPOROUS SURFACES
UHB Tape (ultra high bond): Make sure the Rev-
Loc™ is clean and dry. a) Apply UHB tape in the
middle of he Rev-Loc™ and b) burnish it onto the
Rev-Loc™ from the center out so as not to entrap
any air bubbles. Ensure window surface is clean.
Rubbing alcohol is a good cleaning agent prior to
installation. c) Screw Rev- Loc™ onto the SSP6
noting cable down orientation (make small pencil
mark to top of Rev-Loc™), so as to ensure the
speaker wire faces down, and then unscrew SSP6
Multiducer™. Peel tape backing off and firmly press
Rev-Loc™ onto glass with the pencil mark up as
contact pressure activates the adhesive. Allow glue
to cure ½ hour if able and then screw on the SSP6
Multiducer™ as stated in “Glues” on the previous
page. d) Space the SSP6 Multiducer™ at lease 8”
(20cm) from the glass frame.
DRYWALL (PLASTERBOARD)
Super Glue (cyanoacrylate). Choose a quality
brand in a medium to light viscosity cyanoacrylate
(super glue) and apply in a tight zigzag pattern no
further than ¼” (6mm) spacing covering the surface,
and immediately press firmly on to a dust free clean
and dry surface. If placing in a wall stud bay, offset
from the center by 2”. Allow glue to set and then
apply the SSP6 Multiducer™ as stated in “Glues” on
the previous page.
ROUGH SURFACES
5 Minute Epoxy glue or Methacrylate. Fiberglass
and rougher finished wood and the like surfaces
should be clean, dry and dust free. If applying to
rough fiberglass, sand high points down slightly.
Apply glue to entire bottom surface of Rev-loc™
mounting plate as well as the surface to be glued to
in a thin layer. Apply to surface and twist back and
forth very slightly to squeeze out excess glue and
seat the Rev-Loc™ well. Tape in place, let glue set
and then apply the SSP6 Multiducer™ as stated in
“Glues” on the previous page.
Speaker
Cable
Mark
A
B
C
D
8” (20cm) min
8” (20cm) min
Apply glue
to entire
surface
®
2” (5cm) minimum oset from center
Plaster drywall
cavity
Loading...