Revo REVDN650-1 User Manual
2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated ''dangerous
voltage'' within the product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
PRECAUTIONS
WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Safety
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by
qualified personnel before operating it any further.
Unplug the unit from the wall outlet if it is not going to
be used for several days or more.
To disconnect the cord, pull it out by the plug. Never
pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on soft surfaces (rugs,
carpets, sofas, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.
Height and vertical linearity controls located on the
rear panel are for special adjustments by qualified
personnel only.
Installation
Do not install the unit in an extremely hot or humid place
or in a place subject to excessive dust, mechanical
vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Cleaning
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzine as they might
damage the finish of the unit.
Retain the original carton and packing materials for safe
transport of this unit in the future.
3
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED
AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE,
PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED
TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL
ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED
BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.
WARNING: This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the m
DQXIDFWXUHU¶VLQVWUXFWLRQV
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plu
g. A polarized plug has two blades with one wider than the other. A gro
unding type plug has two blades and a third grounding prong. The wid
e blade or the third prong are provided for your safety. If the provided p
lug does not fit into your outlet, consult an electrician for replacement o
f the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from th
e apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use cau
tion when moving the cart/apparatus combination to avoid injury from ti
p-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-su
pply cord or plug is damaged, liquid has been moisture, does not oper
ate normally, or has been dropped.
15. CAUTION ± THESE SERVICING INSTRUCTIONS ARE FOR USE B
Y QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RIS
K OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OT
HER THAN THAT CONTAINED IN THE OPERATING INSTRUCTION
S UNLESS YOU QRE QUALIFIED TO DO SO.
16. Use Certified/Listed Class 2 power source only.
5
CONTENTS OF PACKAGE
The package contains the following
Camera in Housing ------------------------------------------------------------------1
Instruction Manual (This Document) --------------------------------------------1
Accessory Kit for Installing ---------------------------------------------------------1
Drilling guide label -------------------------------------------------------------------1
TABLE OF CONTENTS
INTRODUCTION --------------------------------------------------------------------------------------- 4
CAMERA CONNECTIONS -------------------------------------------------------------------------- 5
INSTALLATION ----------------------------------------------------------------------------------------- 6
LENS ADJUSTMENT --------------------------------------------------------------------------------- 7
DC AUTO IRIS LENS --------------------------------------------------------------------------------- 8
OPERATING CAMERA ------------------------------------------------------------------------------- 8
CAMERA ADJUSTMENT ---------------------------------------------------------------------------- 9
EXTERNAL DIMENSION----------------------------------------------------------------------------- 16
SPECIFICATIONS ------------------------------------------------------------------------------------- 17
6
INTRODUCTION
The camera provided high-quality image using SONY Wide Dynamic 1/3´ CCD and
digital signal processing LSIs.
Features:
ˍ 1/3´ Super- HADII PS 960H CCD
ˍ Super high-resolution of 650TV lines
ˍ 0.4 lux(Color), 0.04 lux(B/W), 0.001 lux(Low-Shutter) @ F1.4 Sensitivity
ˍ Auto Electronic Shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter
modes [1/60(1/50) ~ 1/10,000]
ˍ On Screen Display (OSD)
ˍ Auto and Manual white balance modes
ˍ Support Line-Lock external synchronization
ˍ Digital PTZ
ˍ Digital Effect (H/V reverse, 180 degree rotate, inverse, freeze)
ˍ 2D-NR, 3D-NR (DNR Demo)
ˍ Back Light Compensation
ˍ Back Light Masking (MAX. 15 area)
ˍ Excessive High-Light Compensation
ˍ Wide Dynamic Range (~x512)
ˍ Various Detection Method (zone detection, motion trace, face trace, mine area,
absent detection, cross object counting, entrance counting)
ˍ Day & Night(Auto, Manual, External, Filter delay)
ˍ Various Alarm Method (Period, Snooze, Polarity Select)
ˍ Privacy Mask or Mosaic (MAX. 15 area/4-point polygonal/transparency)
ˍ Scene Change Detection
ˍ Sens-Up (~x32)
ˍ White Pixel Remove
ˍ Frame Control (Auto, 1~7 sec)
ˍ System Lock (4-Digit password)
ˍ RS-485 Remote camera control
ˍ F1.4 D&N DC iris vari-focal lens
ˍ Operates in 12VDC or 24VAC
ˍ User Certified / Listed Class 2 power source only
7
CAMERA CONNECTIONS
Connection Cable Description
COLOR
Description
RED
AC24V/DC12V
WHITE
AC24V/DC12V
ORANGE
ADKEY
BROWN
GND
BLUE
RS485(-)
GREEN
RS485(+)
YELLOW
ALARM OUT
GRAY
DN EXT-IN
BLACK&WHITE
DN EXT-OUT
BLACK
GND
SKY BLUE
UTP+(optional)
PINK
UTP- (optional)
1) External Day/Night Control : To select Day/Night mode using external equipment,
by connecting control lines to the appropriate terminals.
¾ DAY&NIGHT OUTPUT (Black&White)
Is the camera function that can turn on an external IR LED Lamp by detecting
the sensitivity on the AGC level when the D&N mode is set "AUTO" on the
OSD menu of the camera
¾ DAY&NIGHT EXTERNAL INPUT (Gray)
Is the camera function that can be switched to DAY Mode or NIGHT mode by
receiving the D&N on/off signal from external light sensor or IR LED LAMP.
This needs the D&N Mode to be set to "External" on the OSD menu of the
camera to work
2) Alarm Out
¾ Motion detection signals are output through this port. (YELLOW AND GND)
¾ Active state is configurable.
3) Power Input Terminal
¾ RED & WHITE : DC Power is recommended to use the DC power supply that can
support inrush current over 0.75A
4) Camera Control
¾ GREEN : RS 485+
¾ BLUE : RS 485-
5) UTP (optional)
¾ Video signal through out the UTP Cable (SKY BLUE(+) & PINK(-) )
DAY&NIGHT INPUT
Gray
GND
Black
Close contact: NIGHT
Open contact: DAY
GND
Black
DAY&NIG
Black&White
5V/10mA : IR LED ON (NIGHT)
0V : IR LED OFF (DAY)
Loading...