Page 1
RT 3000
( Beer Tower )
User’s Manual
Page 2
ReverseTap
Beer Tower
Silicone Cap
Model RT-3000 ( Plastic food container )
Dimensions
( Weight )
200 * 200 * 785 mm ( 1.6 kg WT )
Capacity
Optimal Volume : 3000 mL ( 100 oz )
Maximum Volume : 4512 mL (152 oz.)
Material
( Operating
Temperature )
Tower : Tritan, Acryl, ABS
-10 ~ 80℃
Silicone cap : Silicone
Manufacturer NPC Co., Ltd. ( South Korea )
* Tritan is an eco-friendly material in which bisphenol-A(BPA), an
environmental hormone, has not been detected from.
- Be careful no to let any foreign substance get in between parts.
- Do not apply excessive force to the product. It may result in leakage or scratch to the
product.
- Do not use ReverseTap Beer Tower for anything other than its intended use.
- Do not boil the product in boiling water nor heat directly in the flame.
- Do not stretch the cap with excessive force. It may result in product failure.
- We will not be held responsible or accept any liability for any damage to the product
caused due to customer’s carelessness.
- Actual product may look different from pictures on the manual.
- This user’s manual may be downloaded from ReverseTap website. ( www.reversetap.com )
Caution
Specification
Page 3
Product Components
①
②
⑩
⑨
⑧
⑦
⑥
⑤
④
③
⑤
No. 부 품 명 Assembly
① Ice Pipe Cover
Ice Pipe Assembly② Beer Pipe Cover
③ Ice Pipe
④ Beer Pipe
Beer Pipe Assembly
⑤ Silicone / O-ring
⑥ Cap Body
⑦ Silicone Cap
⑧ Plastic Tap
Tap Assembly⑨ Tap Body
⑩ Base Body
※ The O-ring and the silicone part of plastic tap
are for water sealing. Please be careful not to
damage them since it may cause leakage.
Page 4
How to disassemble ReverseTap Beer Tower
② Pull out beer pipe cover and take out ice pipe assembly.
③ Twist the cap body and disassemble from beer pipe.
⑥ Twist the plastic tap을 90˚ and pull out
④ Pucker and push the silicone cap into the cap body.
① Pull out Ice pipe cover and disassemble ice pipe assembly.
⑤ Pull down the tap body and disassemble from the cap body.
※ The assembling shall be the reverse process of the above.
※ You can disassemble the beer pipe assembly
more easily by pushing the upper end of beer
pipe back, while the plastic tap body is anchored.
Page 5
- It may cause a lack of watertightness if the cap is folded or overlapped as shown
in the picture.
2.
3.
- Ensure the cap assembly is the same as the picture shown.
- The top and the bottom of the cap must be seated on the inner and the bottom surface
of the cap body, respectively.
※ Be careful not to let any foreign substance get in between the cap and the cap body.
How to assemble Silicone Cap
1.
- Place the silicone cap on the bottom hole of the cap body and push the cap in to
assemble.
※ Put on sanitary gloves before assembling.
Page 6
- Fill the ice pipe with ice before using the ReverseTap Tower with
dispenser.
- Ensure the ice pipe and beer pipe is aligned parallel as the picture
shown.
- Close beer pipe cover and ice pipe cover tightly.
1.
2.
- To assemble Beer Tower to the dispenser, grab the
beer pipe assembly with two hands and press the
Beer Tower with the center of cap and nozzle is
properly aligned.
- Ensure the bottom of the cap body is horizontally
aligned.
Ice
Ice pipe
assembly
- You can fill ice in the ice pipe by opening ice pipe cover.
※ Please fill the ice pipe with ice prior to beverage injection or dispense with ice pipe
disassembled. The ice pipe assembly may float if beer is dispensed while the ice pipe is
empty.
※ Do not freeze ice pipe with water filled. It may damage the ice pipe.
How to use the Ice Pipe
※ The insertion may be hard due to friction
between the cap and the nozzle if they are
dry, so rinse the Fit or the nozzle with clean
water beforehand for an easy use.
How to use ReverseTap Beer Tower
Page 7
- You can pour beverage by pulling or pushing the plastic tap back and
forth.
5.
※ After ReverseTap Beer Tower is used, it is recommended to
disassemble each part and wash them in clean water.
- To assemble the beer pipe assembly to the tap assembly, align the center of silicone cap and
the extruded pin of the tap body and press the beer pipe assembly down to the tap assembly
to the end.
4.
- We recommend users to disassemble, wash in clean water, and keep ReverseTap Beer
Tower after its use. ( Refer to “
How to disassemble ReverseTap Beer Tower
” )
- ReverseTap Beer Tower is dishwashable within 80℃ water temperature.
- Do not use scrubs of polishing powders with rough surfaces for washing.
※ How to wash RA CR1 (silicone cap)
- Rub silicone cap softly in a diluted neutral detergent with warm water and then rinse
with clean water.
- Use of dishwasher is possible with good drainage tools such as net shaped container.
- After washing, gently shake off or tap onto a clean dry towel to dry.
- For more detailed demonstration, watch uploaded video clip on ReverseTap website.
How to wash ReverseTap Beer Tower
3.
- After the beverage filling is complete, disassemble the Tower from the
dispenser safely.
- It is easier to disassemble if you grab the upper part of the beer pipe
and disassemble in a manner of pulling or pushing it back and forth.
How to use ReverseTap Beer Tower
Loading...