REVELL 4217, '68 Dodge Dart Hemi 2'N1 Instructions Manual

The 1968 Dodge Dart was hot with the

440 engine, but Chrysler also made an
even hotter limited number of ultra high
performance Darts equipped with a HEMI
engine. These were light weight Dart GTS
hardtops and Chrysler noted they were
"intended for use in supervised acceleration
trials and not intended for general highway
use" and were delivered with no warranty.
Your Revell model features an option­al 426 cubic inch HEMI
two carbs or a 440 cubic inch engine
with a single carburator, a stock inte­rior, hood, wheels and suspension or
racing version interior, suspension, hood
with air scoop and drag slicks. Decals
with factory stock markings plus colorful
drag racing graphics are also included.

®

engine with

KIT 4217 85421700200

'68 DODGE DART HEMI ® 2'N1

®

* REPEAT SEVERAL TIMES

* A REPETER PLUSIEURS FOIS

READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER

* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be

marked by a star (★) to indicate chrome
plated plastic.

* For better paint and decal adhesion, wash

the plastic parts in a mild detergent solution.
Rinse and let air dry.

* Check the fit of each piece before

cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas

to be cemented.
* Allow paint to dry thoroughly before

handling parts.
* Any unused parts may be discarded.

DECAL APPLICATION INSTRUCTIONS

1. Cut desired decal from sheet.

2. Dip decal in water for a few seconds.

3. Place wet decal on paper towel.

4. Wait until decal is movable on paper backing.

5. Place decal in position on model, face up and

slide backing away.

6. Press out air bubbles with a soft damp cloth.

7. Milkiness that may appear is for better decal

adhesion and will dry clear. Wipe away any

excess adhesive.

8. Do not touch decal until fully dry.

9. Allow the decals 48 hours to dry before

applying clear coat.

NOTE: Decals are compatible with

setting solutions or solvents.

* REPEAT PROCEDURE

* R E PE T EZ L E P R OC E DE

* OPTIONAL PARTS

`` ` ` ` `

* PIECES EN OPTION

* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont

marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.

* Pour une meilleure prise de la peinture et des autocollants,

laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.

* Vérifier que chaque pièce s'ajuste bien avant

de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.

DIRECTIVES D'APPLICATION DES AUTOCOLLANTS

1. Découper l'autocollant désiré de la feuille.

2. Tremper l'autocollant dans de l'eau pendant quelques secondes.

3. Placer l'autocollant mouillé sur une serviette en papier.

4. Attendez que l'autocollant puisse être déplacé sur son

support en papier.

5. Mettre l'autocollant en position sur le modèle face sur

le dessus et faire glisser le support pour l'enlever.

6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.

7. La substance laiteuse qui peut apparaître est destinée à

améliorer l'adhésion de l'autocollant et devient incolore au

séchage. Essuyer pour enlever tout excédent d'adhésif.

8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.

9. Laisser l'autocollant sécher pendant 48 heures avant

d'appliquer une couche transparente.

REMARQUE: Les autocollants sont compatibles avec

* DECAL

* DECAL COMANIE

les solutions de fixage ou les solvants.

*ATTENTION D ASSEMBLEE

* ASSEMBLY CAUTION

* CEMENT TOGETHER

* A COLLER

This paint guide is provided to complete this kit

Ce guide de peintures est fourni pour reproduire le modèle

Gloss White

Semi Gloss Black

Silver

Aluminum

Steel

Gloss Orange

Chrysler Engine Red

Transparent Red

Turn Signal Amber

Gold

Tan

* REMOVE AND THROW AWAY

* A RETIRER ET JETER

as shown on the box.

réduit qui apparaît sur la boîte.

Blanc brillant

Noir Satiné

Argent

Aluminium

Acier

Orange brillant

Rouge moteur Chrysler

Rouge transparent

Ambre

Or

Havane

* DO NOT CEMENT

* NE PAS COLLER

If you have any questions or comments, call our hotline at: [phone]

Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007

Be sure to include the plan number (85421700200), part number, description, your return address and phone number.

Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.

or, please write to:

Visit our website: www.revell.com

1

426 HEMI

ENGINE ASSEMBLY

ASSEMBLE HEADERS TO ALLOW CLEAR-

ANCE FOR #44 - FRONT SUSPENSION

SHOWN IN STEP 8

A

★121

RIGHT

ROCKER

COVER

CHROME

109
WATER PUMP /
TIMING COVER

CHRYSLER ENGINE RED

RIGHT ENGINE HALF

CHRYSLER ENGINE RED

440 MAGNUM

101

103

CYLINDER

HEAD

CHRYSLER

ENGINE RED

LEFT ENGINE HALF

CHRYSLER ENGINE RED

CYLINDER

ENGINE RED

108

OIL PAN

CHRYSLER

ENGINE RED

(SHADED AREA

100

103

HEAD

CHRYSLER

ALUMINUM)

★120
LEFT

ROCKER

COVER

CHROME

B

111

IGNITION

COIL

SEMI

GLOSS BLACK

112

DISTRIBUTOR

ALUMINUM

(SHADED AREA

SEMI GLOSS

BLACK)

119

RIGHT

EXHAUST

HEADER

STEEL

107

FAN

SEMI GLOSS BLACK

★124

ALTERNATOR

CHROME

(ALUMINUM)

106

FAN BELT

SEMI GLOSS BLACK

★123

VELOCITY STACKS

CHROME

★122

CARBURETORS

CHROME

105

INTAKE MANIFOLD

ALUMINUM

110

STARTER

SEMI GLOSS

BLACK

118

LEFT EXHAUST

HEADER

STEEL

A

★57

RIGHT

ROCKER COVER

CHROME

55

CYLINDER

HEAD

CHRYSLER

ENGINE RED

ENGINE FRONT

CHRYSLER ENGINE RED

MANIFOLD

ENGINE RED

62

54

RIGHT

ENGINE HALF

CHRYSLER ENGINE RED

★59

CARBURETOR

CHROME

58

INTAKE

CHRYSLER

(GOLD)

(SHADED AREA

ALUMINUM)

53

LEFT ENGINE HALF

CHRYSLER ENGINE RED

55

CYLINDER

HEAD

CHRYSLER

ENGINE RED

TRANSMISSION PAN

OIL PAN

CHRYSLER ENGINE RED

61

ALUMINUM

60

★56

LEFT

ROCKER

COVER

CHROME

B

67

DISTRIBUTOR

TAN

(SHADED AREA

ALUMINUM)

70

RIGHT

EXHAUST MANIFOLD

STEEL

★94

ALTERNATOR

BACK

CHROME

(ALUMINUM)

★64

ALTERNATOR

CHROME

(ALUMINUM)

BELT / PULLEYS

SEMI GLOSS

20

FAN

SEMI GLOSS

BLACK

66

IGNITION COIL

SEMI GLOSS BLACK

(SHADED AREA

STEEL)

63

BLACK)

65

STARTER

SEMI GLOSS BLACK

DECAL

68

AIR

CLEANER

SEMI GLOSS

BLACK

20

*

6

DECAL

69

LEFT

EXHAUST MANIFOLD

STEEL

Kit 4217 - Page 2

2

INTERIOR ASSEMBLY

426 HEMI

13

DECAL

★126

HURST

SHIFTER

CHROME
(SEMI GLOSS BLACK BOOT &
GLOSS WHITE SHIFTER BALL

30

RIGHT

DOOR PANEL

SEMI GLOSS BLACK

(SILVER DETAILS)

*

115

ROLL BAR

SEMI GLOSS BLACK

(SHADED AREAS FLAT BLACK)

141

ROLL BAR

SUPPORTS

SEMI GLOSS BLACK

29

LEFT DOOR PANEL

SEMI GLOSS BLACK

(SILVER DETAILS)

DECAL

2

DECAL

1

37

DASH FRONT

SEMI GLOSS BLACK

36

DASH TOP

SEMI GLOSS BLACK

SEAT

FRONT

SEMI GLOSS

BLACK

TACHOMETER

39

4

DECAL

★35

CHROME

33

STEERING WHEEL

SEMI GLOSS BLACK

(SHADED AREA

SILVER)

STEERING COLUMN

34

SEMI GLOSS BLACK

40

SEAT BACK

SEMI GLOSS

BLACK

113

HEMI INTERIOR

SEMI GLOSS BLACK

440 MAGNUM

★32

SHIFTER

CHROME

30

RIGHT

DOOR PANEL

SEMI GLOSS BLACK

(SILVER DETAILS)

3

DECAL

*

★31

CONSOLE

CHROME

(RECESSED AREAS

ALUMINUM)

DECAL

2

DECAL

4

1

37

DASH FRONT

SEMI GLOSS BLACK

36

DASH TOP

SEMI GLOSS BLACK

39

SEAT

FRONT

SEMI GLOSS

BLACK

DECAL

★35

TACHOMETER

CHROME

STEERING COLUMN

SEMI GLOSS BLACK

33

STEERING WHEEL

SEMI GLOSS BLACK

(SHADED AREA

SILVER)

34

40

SEAT BACK

SEMI GLOSS

BLACK

28

INTERIOR

SEMI GLOSS BLACK

LEFT DOOR PANEL

SEMI GLOSS BLACK

29

(SILVER DETAILS)

Kit 4217 - Page 3

3

BODY WORK ASSEMBLY

426 HEMI

*

1

BODY

BODY COLOR

(WINDOW TRIM SILVER)

11

DECAL

NOTE: CAREFULLY SAND OFF THE GTS LOGO.

NOTE: CAREFULLY SAND OFF THE FRONT TURNSIGNAL
MARKERS AND GTS LOGOS.

440 MAGNUM

1

BODY

BODY COLOR

(WINDOW TRIM SILVER)

Kit 4217 - Page 4

NOTE: FOLLOWING THE CHANNELED LINE ON THE INSIDE OF
THE BODY CAREFULLY REMOVE THE WHEEL OPENING.