REVELL H.M.S Campbeltown, 3016 Assembly Instructions Manual

World War II, March 28, 1942, it was a pitch black

night at the docks of St. Nazaire, France. Alarm
sirens screamed, searchlight beams pierced the
darkness searching for an intruder. Under full
steam, the battle-scarred Campbeltown, stacks
belching smoke, bore down on the dry docks.
Gallant British seamen manned the forward
gun, warding off the enemy fire. Campbeltown's
mission, ram the dock which was to be used to
repair the dreaded German battleship, Tirptz. Once
into the dock, a cache of explosives hidden deep
within the ship would put the German repair depot
permanently out of commission. But the explosives
failed to ignite, and the Campbeltown and part of
her crew were captured by the puzzled but elated
Germans. Nine hours later as the captors were
showing off their prize, the venerable Campbeltown,
the world war II version of the Trojan Horse,
inexplicably exploded killing all aboard and
rendering the dock inoperable for the rest of the war.
Your Revell model features a detailed bridge,
deck, four stacks, antennas, life boats and
depth charge racks, armament including four
4" guns, one 3" gun, 12 21" torpedo tubes
and authentic world was II decal markings.

KIT 3016 85301600200

H.M.S. CAMPBELTOWN

* REPEAT SEVERAL TIMES

* A REPETER PLUSIEURS FOIS

READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER

* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be

marked by a star (★) to indicate chrome
plated plastic.

* For better paint and decal adhesion, wash

the plastic parts in a mild detergent solution.
Rinse and let air dry.

* Check the fit of each piece before

cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas

to be cemented.
* Allow paint to dry thoroughly before

handling parts.
* Any unused parts may be discarded.

DECAL APPLICATION INSTRUCTIONS

1. Cut desired decal from sheet.

2. Dip decal in water for a few seconds.

3. Place wet decal on paper towel.

4. Wait until decal is movable on paper backing.

5. Place decal in position on model, face up and

slide backing away.

6. Press out air bubbles with a soft damp cloth.

7. Milkiness that may appear is for better decal

adhesion and will dry clear. Wipe away any

excess adhesive.

8. Do not touch decal until fully dry.

9. Allow the decals 48 hours to dry before

applying clear coat.

NOTE: Decals are compatible with

setting solutions or solvents.

* REPEAT PROCEDURE

* R E P E T E Z L E P R O C E D E

* OPTIONAL PARTS

* PIECES EN OPTION

* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont

marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.

* Pour une meilleure prise de la peinture et des autocollants,

laver les pièces en plastique avec une solution détergente
peu concentrée. Les rincer et les laisser sécher à l'air.

* Vérifier que chaque pièce s'ajuste bien avant

de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.

DIRECTIVES D'APPLICATION DES AUTOCOLLANTS

1. Découper l'autocollant désiré de la feuille.

2. Tremper l'autocollant dans de l'eau pendant quelques secondes.

3. Placer l'autocollant mouillé sur une serviette en papier.

4. Attendez que l'autocollant puisse être déplacé sur son support

en papier.

5. Mettre l'autocollant en position sur le modèle face sur

le dessus et faire glisser le support pour l'enlever.

6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.

7. La substance laiteuse qui peut apparaître est destinée à

améliorer l'adhésion de l'autocollant et devient incolore au

séchage. Essuyer pour enlever tout excédent d'adhésif.

8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.

9. Laisser l'autocollant sécher pendant 48 heures avant

d'appliquer une couche transparente.

REMARQUE: Les autocollants sont compatibles avec

* DECAL

* DECAL COMANIE

les solutions de fixage ou les solvants.

*ATTENTION D ASSEMBLEE

* ASSEMBLY CAUTION

* CEMENT TOGETHER

* A COLLER

This paint guide is provided to complete this kit

Ce guide de peintures est fourni pour reproduire le modèle

Aluminum

Brass

Dark Red

Gray

Light Gray

Semi Gloss black

Tan

* REMOVE AND THROW AWAY

* A RETIRER ET JETER

as shown on the box.

réduit qui apparaît sur la boîte.

Aluminium

Laiton

Rouge foncé

Gris

Gris clair

Noir satiné

Havane

* DO NOT CEMENT

* NE PAS COLLER

If you have any questions or comments, call our hotline at: [phone]

Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007

Be sure to include the plan number (85301600200), part number, description, your return address and phone number.

Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.

or, please write to:

Visit our website: www.revell.com

1

FORE DECK ASSEMBLY

3

STEERING

STATION FRONT

LIGHT GRAY

1

LARGE GUN

GRAY

SEMI GLOSS BLACK

STEERING STATION

4

LEFT SIDE

LIGHT GRAY

FORE DECK AMMUNITION

10

ALUMINUM

STEERING STATION

5

RIGHT SIDE

LIGHT GRAY

RIGHT

AMMUNITION

LIGHT GRAY

12

BOX

9

HELM

GRAY

6

BRIDGE

LIGHT GRAY

TORPEDO DIRECTOR

8

(SHOWN IN PLACE)

ALUMINUM

TORPEDO DIRECTOR

8

ALUMINUM

7

PELORUS

(SHOWN IN PLACE)

ALUMINUM

7

PELORUS

ALUMINUM

TAN

(DECK)

11

LEFT

AMMUNITION

BOX

LIGHT GRAY

ALUMINUM

Kit 3016 - Page 2

ALUMINUM

ALUMINUM

2

FORE DECK

TAN

2

AFT DECK ASSEMBLY

14

AFT DECK

TAN

ALUMINUM

13

TORPEDO TUBES

(SHOWN IN PLACE)

GRAY

SHADED AREA ALUMINUM

13

TORPEDO TUBES

GRAY

TORPEDO TUBE

RETAINERS

19

DECK HOUSE

FORE WALL

LIGHT GRAY

ALUMINUM

15

16

DECK HOUSE

RIGHT SIDE

LIGHT GRAY

DECK HOUSE LEFT SIDE

LIGHT GRAY

17

DECK HOUSE

AFT WALL

LIGHT GRAY

18

3

26

SIGNAL BRIDGE

LIGHT GRAY

1ST

COMPLETED FORE

DECK ASSEMBLY

HULL / STAND ASSEMBLY

RIGHT EMERGENCY

24

CABIN RT. SIDE

LIGHT GRAY

25

LEFT EMERGENCY

CABIN LT. SIDE

LIGHT GRAY

A B

DECKS

HULL HULL

STAND STAND

COMPLETED AFT
DECK ASSEMBLY

SPRING OUTWARD

2ND

20

RIGHT HULL HALF

LIGHT GRAY

DARK RED

SEMI GLOSS

BLACK

21

LEFT HULL HALF

LIGHT GRAY

22

STAND

SEMI GLOSS BLACK

23

RUDDER

DARK RED

Kit 3016 - Page 3