Revel M Stand User Manual

M Stand Assembly Instructions

NOTE: All of the parts shown in the following illustrations are supplied

with the M-Stands.

1. Attach the stand base to the stand riser as shown in the illustration below.

Large
Allen Wrench

Black M6 x 50mm
Fine-Thread Bolt

Washer

2. Spin the clamping rings onto the spikes and insert the spikes into the bases
as shown in the illustration below. You can install the spikes with either the
pointed end or rounded end protruding from the base.

3. Attach the stand top to the stand riser as shown in the illustration below.

Large
Allen Wrench

Black M6 x 30mm
Fine-Thread Bolt

Washer

4. Attach the speaker to the stand as shown in the illustration below. Only
Revel Performa3 M106 and M105 speakers can be attached to the M-Stand.
Use the VELCRO

®

strap on the rear of the stand for wire management.

Spike and

Locking Ring

Washer

Pointed end out

(carpeted floors)

Rounded end out
(wood or tile floors)

• If the stands are to be placed on a carpeted oor, install the spikes with the

pointed ends protruding from the stand base.

• I f the stands are to be placed on a wood or tile oor, install the spikes with

the round ends protruding from the stand base.

After determining the final locations for the speakers you can place coins under

the spikes to protect the oor surface from damage.

NOTE: If you wish you can install the spikes with the pointed ends
protruding from the stands for placement on wood or tile oors. In this

case you must place coins or similar items under the spikes to avoid

damaging the oor surface.

Rotate the locking ring clockwise to firmly secure the spike to the cabinet.
Make sure to thread the locking rings of all four spikes to achieve a level

balance when the stand is placed rightsideup on the oor.

Washer
3/4" 1/4 x 20

Coarse-Thread Bolt

Small
Allen Wrench

C Stand Assembly Instructions

NOTE: All of the parts shown in the following illustrations are supplied

with the C-Stands.

1. Attach the stand base to the stand riser as shown in the illustration below.

Large
Allen Wrench

Black M6 x 50mm
Fine-Thread Bolt

Washer

2. Spin the clamping rings onto the spikes and insert the spikes into the bases
as shown in the illustration below. You can install the spikes with either the
pointed end or rounded end protruding from the base.

Spike and
Locking Ring

Washer

Pointed end out
(carpeted floors)

Rounded end out

(wood or tile floors)

• If the stand is to be placed on a carpeted oor, install the spikes with the

pointed ends protruding from the stand base.

• If the stand is to be placed on a wood or tile oor, install the spikes with

the round ends protruding from the stand base.

After determining the final locations for the speakers you can place coins under

the spikes to protect the oor surface from damage.

3. Attach the stand top to the stand riser as shown in the illustration below.

Large Allen Wrench
Black M6 x 30mm

Fine-Thread Bolt
Washer

4. Attach the speaker to the stand as shown in the illustration below. Only
Revel Performa3 C208 and C205 speakers can be attached to the C-Stand.

Washer
Black M8 x 30mm

Fine-Thread Bolt
Small

Allen Wrench

IMPORTANT: If you are attaching the C208 or C205 to the C-Stand
you cannot use the adjustable feet that were included with the
speaker. The C-Stand places the speaker at the proper angle for
seated listeners without requiring additional adjustments.

NOTE: If you wish you can install the spikes with the pointed ends

protruding from the stands for placement on wood or tile oors. In this

case you must place coins or similar items under the spikes to avoid

damaging the oor surface.

Rotate the locking ring clockwise to firmly secure the spike to the cabinet.
Make sure to thread the locking rings of all four spikes to achieve a level

balance when the stand is placed rightsideup on the oor.

HARMAN International Industries, Incorporated
8500 Balboa Boulevard, Northridge, CA 91329 USA

© 2012 HARMAN International Industries, Incorporated. All rights reserved.

Revel and the Revel logo are trademarks of HARMAN International Industries, Incorporated, registered in the United

States and/or other countries.

VELCRO is a registered trademark of Velcro Industries B. V.

Features, specications and appearance are subject to change without notice.

For questions, assistance or additional information concerning any of our products, call us at: [phone] or (888)
691-4171. For technical support, submit your detailed inquiry to:[e-mail].

Part No. REVP4838 Rev: A www.revelspeakers.com