Revel IC6T2 User Manual

Revel

®

IW65/IW80 In-Wall Loudspeakers

IC65/IC80/IC6T2 In-Ceiling Loudspeakers

Owner’s Manual

2

Revel Concerta IW65/IW80&IC65/IC80/IC6T2

Owner’s Manual

DOCUMENTATION CONVENTIONS

This document contains general safety,installation and operation instructions for the Revel®Concerta™IW65/IW80 in-wall
loudspeakers and the IC65/IC80/IC6T2 in-ceiling loudspeakers.It is important to read this document before attempting to use
these products.Pay particular attention to safety instructions.

WARNING!

Calls attention to a procedure, practice, condition or the like that,
if not correctly performed or adhered to, could result in injury
or death.

CAUTION!

Calls attention to a procedure, practice, condition or the like that,
if not correctly performed or adhered to, could result in damage
to or destruction of part or all of the product.

Note:
Calls attention to information that is essential to highlight.

3

Revel Concerta IW65/IW80&IC65/IC80/IC6T2
Owner’s Manual

ABOUT THE REVEL

®

CONCERTA

™

IW65/IW80 IN-WALL
AND IC65/IC80/IC6T2
IN-CEILING
LOUDSPEAKERS

Since 1996,the Revel name has stood for the best in
loudspeaker design and performance.Backed by
Harman International’s extensive research and design
facilities,Revel loudspeakers benefit from cutting-edge
development tools such as:

•a multichannel listening lab for double-blind,
position-independent listening tests

•a laser interferometer, which enables detailed driver
and baffle/frame analysis

• multiple large anechoic chambers, which allow for
precise tests and measurements

• finite element analysis, utilized for advanced
loudspeaker modeling

•a stereo lithography apparatus, which helps achieve
extraordinarily tight tolerances

The Revel Concerta IW65/IW80 in-wall and IC65/IC80/
IC6T2 in-ceiling loudspeakers draw upon the same
research, resources and unique perspectives that put all
Revel loudspeakers in a class by themselves.Revel
Concerta Series loudspeakers provide unparalleled
value and are known for their standard-setting low
coloration and freedom from distortion over an
extraordinarily wide dynamic range.

The Revel Concerta IW65/IW80 in-wall and IC65/IC80/
IC6T2 in-ceiling loudspeakers provide audibly superior
performance, validated by our state-of-the-art listening
facilities, that far outclasses comparable products from
our competitors.

HIGHLIGHTS

•

6-1/2" (165mm) or 8" (200mm) woofer with a Micro
Ceramic Composite (MCC) cone for high output with
low distortion.

• 1" (25mm) angle-adjustable tweeter with Micro
Ceramic Composite (MCC) dome and integrated
waveguide provide optimized response both on­and off-axis.

• High-order crossover network with premium-quality
components for exceptionally accurate timbre
reproduction.

• Boundary Compensation switch maintains accuracy
when placed near a secondary boundary (wall or
ceiling).

• Three-position Tweeter-Level control provides
optimum response, whether used with or without
grilles.

PRODUCT REGISTRATION

Please register your IW65/IW80 in-wall or IC65/IC80/IC6T2
in-ceiling loudspeakers within 15 days of purchase.
To do so,register online at www.revelspeakers.com.
Retain the original dated sales receipt as proof of
warranty coverage.

4

Revel Concerta IW65/IW80&IC65/IC80/IC6T2

Owner’s Manual

INSTALLATION
CONSIDERATIONS

Loudspeaker fidelity depends on the following factors:

• Loudspeaker accuracy and placement

• Listening-room acoustics
But not all listening spaces can accommodate the ideal

conditions for these two factors.Therefore, careful
attention to the placement of your Revel in-wall and
in-ceiling loudspeakers will have the most significant
impact on the general performance of the loudspeakers.

The advanced design features of Revel loudspeakers
allow the Concerta in-wall and in-ceiling loudspeakers
to achieve the best possible sound quality in any listening
space. Revel loudspeakers also provide a level of control
not usually available over the sound of the speaker.The
Boundary Compensation switch and the High-Frequency­Level control provide fine-tuning ability,even after the
speaker has been installed.

Boundary Compensation Control

The Boundary Compensation switch controls the level
of bass output of the speaker to accommodate for
the greater reflection of bass caused by a close
secondary wall.

Figure 1: IW65/IW80 control locations

When possible, avoid placing the loudspeakers within
two feet of an adjacent wall or ceiling. If the loudspeaker
must be placed less than two feet from a secondary
boundary (wall or ceiling), turn the Boundary
Compensation switch to the “On”position.

High-Frequency-Level Control

The High-Frequency-Level control allows for the fine-tuning
of the tweeter output level.This three-position switch
provides the listener with the ability to adjust the high­frequency range for various acoustical environments.

Figure 2: IC65/IC80 control locations

The High-Frequency-Level control has three positions:

• Set the High-Frequency-Level control to the center
“0” position if the speaker will be used with the grille
on.This is the normal setting.

• Set the High-Frequency-Level control to the lower “–”
position if the speaker will be used without a grille.

• Set the High-Frequency-Level control to the upper
“+” position if an increased high-frequency level
is desired.

Figure 3: IC6T2 control locations

High-Frequency-Level

Boundary Compensation Control

Control

High-Frequency-Level

Boundary
Compensation Control

High-Frequency-Level

Control

High­Frequency­Level
Control

Boundary
Compensation Control

5

Revel Concerta IW65/IW80&IC65/IC80/IC6T2
Owner’s Manual

LOUDSPEAKER
PLACEMENT

The following general placement suggestions
are accompanied by diagrams for recommended
loudspeaker locations.

IW65/IW80 IN-WALL
LOUDSPEAKER PLACEMENT –
2-CHANNEL STEREO

Before installing the loudspeakers, survey the listening
area, keeping the following points in mind and using
Figure 4 as a guide:

• Place the left and right loudspeakers as close to the
same distance from the primary listening area as
possible, and also at an equal distance from the
side walls.

Ideally,the distance between the left and right
loudspeakers should be slightly less than their
distance from the primary listening area.The
distance between the left and right loudspeakers
should also be the same distance as from the
loudspeakers to the side walls.

• When installing in the wall, position each speaker so
that the tweeter is as close to ear level as possible.

Note:
Avoid placing the woofers at the 1/4, 1/2 or
3/4 wall height positions to prevent low­frequency cancellation.

• Refer to the following “Home Theater”placement
section if you also plan to use the speakers in a
home theater system.

Figure 4: IW65/IW80 in-wall loudspeaker
placement – 2-channel stereo

IW65/IW80 IN-WALL
LOUDSPEAKER PLACEMENT –
HOME THEATER

Before installing the loudspeakers, survey the listening
area, keeping the following points in mind and using
Figures 5 and 6 as guides:

• For front-channel use,place one speaker on the left
and another on the right along either side of the
video screen.

Left and right front loudspeakers should be relatively
close to the sides of the video screen.For example,
left and right loudspeakers used with a 50-inch
video screen should generally not be more than
80 inches apart.

• A center channel speaker should go directly above or
below the video screen and can be an in-wall, on-wall,
in-ceiling or freestanding center channel.

• When installing in the wall, position each speaker so
that the tweeter is as close to ear level as possible.

Note:
Avoid placing the woofers at the 1/4, 1/2 or
3/4 wall-height positions to prevent low­frequency cancellation.

Figure 5: IW65/IW80 in-wall loudspeaker
placement – 5.1-channel system

Channel

Channel

Right Front

Subwoofer

(optional)

Couch

Left Front

Couch

Center Channel

(above or below video screen)

Subwoofer

(optional)

Right Front

Channel

Channel

Left Front

Channel

Surround

Left

Channel

Surround

Right

6

Revel Concerta IW65/IW80&IC65/IC80/IC6T2

Owner’s Manual

Figure 6: IW65/IW80 in-wall loudspeaker
placement – 6- or 7.1-channel system

IC65/IC80 IN-CEILING
LOUDSPEAKER PLACEMENT

The placement of the in-ceiling loudspeakers depends
upon the intended application. Please refer to the section
below that best describes your application.

Distributed Sound – General
Sound Throughout an Area

• Place the loudspeakers as uniformly as possible
throughout the area.

• Place the left and right loudspeakers roughly the
same distance from the primary listener locations.

• To avoid “hot spots,”plan to use more loudspeakers,
each set to a lower volume.

2-Channel Stereo Sound

• Place the left and right loudspeakers as close to
the same distance from the primary listening area
as possible, and also at an equal distance from the
side walls.

Ideally,the distance between the left and right
loudspeakers should be slightly less than their
distance from the primary listening area.The
distance between the left and right loudspeakers
should also be the same distance as from the
loudspeakers to the side walls.

Home Theater Sound

• Left, center and right front loudspeakers should be
centered relative to the video screen.

• Left, center,and right front loudspeakers should not
be dramatically closer to the main listening area
than the video screen is. For example, if the video
screen is 10 feet from the main listening area, the
loudspeakers should not be less than 6 feet from
the main listening area.

• Left and right front loudspeakers should be relatively
close to the sides of the video screen.For example,
left and right loudspeakers used with a 50-inch
video screen should generally not be more than
80 inches apart.

• The center front loudspeaker should go directly
above or below the video screen and can be an
in-wall, in-ceiling or freestanding center channel.

• Left and right side surround loudspeakers should
be as far from the main listening area as possible,
while keeping them at least 2 feet from side and
rear walls.

• In a 5-, 6- or 7.1-channel system, in-ceiling side
surround loudspeakers should be located to the
sides of (directly to the sides of or up to 10 degrees
behind) the primary listening area.

• In a 7.1-channel system, left and right rear surround
loudspeakers should be equidistant from the primary
listening area and generally as far away as possible,
while keeping them at least 2 feet from the side and
rear walls.

IC6T2 IN-CEILING
LOUDSPEAKER PLACEMENT

The placement of the in-ceiling loudspeakers depends
upon the intended application. Please refer to the section
below that best describes your application.

Distributed Sound – General
Sound Throughout an Area

• Place the loudspeakers as uniformly as possible
throughout the area.

• Place the left and right loudspeakers roughly the
same distance from the primary listener locations.

• To avoid “hot spots,” plan to use more loudspeakers,
each set to a lower volume.

Left Front

Channel

Center Channel

(above or below video screen)

Couch

Left
Surround
Channel

Left Rear
Channel

Center Rear

Channel

Right Front

Channel

Subwoofer

(optional)

Surround

Channel

Right Rear

Channel

Right

7

Revel Concerta IW65/IW80&IC65/IC80/IC6T2
Owner’s Manual

2-Channel Stereo Sound

• Place the left and right loudspeakers as close to
the same distance from the primary listening area
as possible, and also at an equal distance from the
side walls.

Ideally,the distance between the left and right
loudspeakers should be slightly less than their
distance from the primary listening area.The
distance between the left and right loudspeakers
should also be the same distance as from the
loudspeakers to the side walls.

MOUNTING
INSTRUCTIONS

The Concerta Series in-wall and in-ceiling speakers
were designed to be simple to install. However,if you
are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your
ability to properly install these loudspeakers, please
contact your Revel dealer or a qualified installer.

Each loudspeaker comes with an integral wall/ceiling
mounting system, designed for installation into the
wallboard between the studs or rafters using the
supplied hardware.

WARNING!

Harman International Industries,
Incorporated, assumes no
responsibility for improper
installation of hardware or for
any personal injuries or product
damage resulting from improper
installation or a loudspeaker
that has fallen.

CAUTION!

Do not substitute mounting
hardware! The supplied
hardware is part of a factory­tested mounting system that
works on wallboard only. To
obtain additional hardware,
contact your authorized
Revel dealer.

The tools required to properly install the in-wall or in-ceiling
speakers are:

• Pencil

• Measuring tape

• Carpenter’s level

• Phillips-head #2 screwdriver – DO NOT use a powered
screwdriver of any kind

• Utility knife

• Awl

• Level

REMOVE POWER

The speaker wires must be connected before the speaker
is fully installed.To protect the audio system and the
installer from accidental electrical shorting and surges
during installation, turn all audio system power off before
starting the speaker installation.

SPEAKER WIRES

Using high-quality speaker wire will maintain the
best sound quality from your Revel in-wall or in-ceiling
speakers. For distances of 100 feet or less, use at
least #16-gauge speaker wire with polarity coding.
For distances of greater than 100 feet, use a t least
#12-gauge wire or heavier.The side of the wire with a
ridge or other coding is usually considered positive (+)
polarity.Also consult the owner’s manuals that were
included with your amplifier or receiver to confirm
proper connection procedures.

Observe polarities when making speaker connections.
Connect each positive terminal on the back of the
amplifier or receiver to the respective positive or “+”
(red) terminal on each speaker.Connect the negative
or “–”(black) terminals in the same way.

CAUTION!

Do not reverse polarities
(i.e., + to – , or – to +) when
making connections. Doing so
will cause poor imaging and
diminished bass response.
Be certain that positive and
negative wire strands are
completely isolated to avoid
short circuits that may
damage your equipment.

Use high-quality loudspeaker cable with a maximum
total loop resistance of 0.07 ohms or less (for each wire
run). Refer to the table on the next page to determine
the appropriate maximum wire gauge.

All in-wall speaker wires must be UL-listed for use with
in-wall applications.

Paint Shield

8

Revel Concerta IW65/IW80&IC65/IC80/IC6T2

Owner’s Manual

CAUTION!

Be sure to comply with
local wiring codes. Harman
International Industries,
Incorporated, is not responsible
for any damages or injuries
that may result from faulty
wiring.

MAXIMUM WIRE GAUGE

Gauge Length Length
(AWG) (Feet) (Meters)

68727

76921

85818

94313

10 34 10

11 27 8

12 22 7

13 17 5

14 14 4

15 11 3

16 9 3

17 7 2

18 5 2

NEW CONSTRUCTION

If you wish to preinstall a rough-in bracket before the
drywall is installed, you will need to purchase the correct
rough-in bracket kit for your loudspeaker model. Detailed
instructions are supplied with the rough-in kit.

INSTALLATION

IW65/IW80 IN-WALL

To add the IW65/IW80 in-wall loudspeakers to finished
construction, proceed with the following instructions.

CAUTION!

Ensure that all audio-system
power is off before beginning
the installation.

1. Remove the plastic

paint shield from the
speaker frame.

2. Determine the correct

speaker location and
use the template
included in the packing
materials and a level
to mark the drywall.

Always allow at least
a 1/2" between the
wall stud and the
speaker cutout or the locking tabs will not have the
space to swivel into place.

3. Ensure that the drywall, plywood or other appropria te

wallboard is at least a 1/2" thick and capable of
withstanding the weight of the speaker being installed.

Cut the drywall along the speaker template marks
made in Step 2.

Level

Template

≥1/2"

≥1/2"

≥1/2"

Paint Shield

9

Revel Concerta IW65/IW80&IC65/IC80/IC6T2
Owner’s Manual

4. Connect the speaker wires to the speaker.Ensure
that the polarity of each connection is correct.

5. Ensure that all four locking tabs are properly
positioned against the locking-tab stops, located on
the speaker frame.

Carefully place the frame assembly into the wall,
ensuring that there is no more than 1/8" play
between the frame and the wall cutout.

After positioning the speaker into the mounting location,
back each screw out one full turn counterclockwise.

6. Screw down each of
the four Phillips-head
screws, alternating
between the four
screws.

The locking tabs will
swivel into place
and secure the unit
to the rear surface
of the wall panel.
Hand-tighten with a nonpowered, straight-handle
Phillips-head screwdriver only.Ensure that the
speaker is securely held in place and that all four
locking tabs are firmly resting against the wall panel.

Note:
Do not use a socket wrench, powered
screwdriver, drill or any other powered tool.

7. Attach the metal grille
and logo.

INSTALLATION

IC65/IC80/IC6T2 IN-CEILING

To add the IC65/IC80/IC6T2 in-ceiling loudspeakers
to finished construction, proceed with the following
instructions.

CAUTION!

Ensure that all audio-system
power is off before beginning
the installation.

1. Remove the plastic
paint shield from the
speaker frame.

2. Determine the correct
speaker location and use
the template included in
the packing materials to
mark the ceiling.

Always allow at least a
1/2" between the ceiling
rafters and the speaker
cutout, or the locking tabs will not have the space to
swivel into place.

3. Ensure that the drywall, plywood or other appropria te
ceiling material is at least a 1/2" thick and capable of
withstanding the weight of the speaker being installed.

Locking Tab

Template

≥1/2"

≥1/2"

≥1/2"

10

Revel Concerta IW65/IW80&IC65/IC80/IC6T2

Owner’s Manual

Cut the drywall
along the speaker
template marks
made in Step 2.

4. Connect the speaker wires to the speaker.Ensure
that the polarity of each connection is correct.

5. Ensure that all four locking tabs are properly
positioned against the locking-tab stops, located on
the speaker frame.

Carefully place the frame assembly into the ceiling,
ensuring that there is no more than 1/8" play
between the frame and the ceiling cutout.

After positioning the speaker into the mounting
location, back each screw out one full turn
counterclockwise.

6. Screw down each of the four Phillips-head screws,
alternating between the four screws.

The locking tabs will swivel into place and secure
the unit to the rear surface of the ceiling panel.
Hand-tighten with a nonpowered, straight-handle
Phillips-head screwdriver only.Ensure that the
speaker is securely held in place and that all four
locking tabs are firmly resting against the ceiling
material.

Note:
Do not use a socket wrench, powered
screwdriver, drill or any other
powered tool.

7. Attach the metal grille
and logo.

Locking Tab

11

Revel Concerta IW65/IW80&IC65/IC80/IC6T2
Owner’s Manual

Painting the Speaker Frame
and Grille

The Revel IW65/80, IC6T2 and IC65/80 loudspeakers
can be painted to match any décor.If you wish to
change their color,the satin finish on the grille and
frame will function as a primer coat. Follow these
instructions for proper painting procedure:

1. Before beginning, carefully remove the grille (if installed),
and install the supplied plastic paint shield securely
into the recess in the baffle.The paint shield will
protect the speaker components and baffle from
paint residue.

2. Gently remove the scrim cloth from the grille
before painting.

3. Use a high-quality spray paint and apply a thin
coat of color.

CAUTION!

Ensure that the grille
perforations remain free
of paint. Filling them with
paint will diminish the
sound quality.

4. A replacement scrim cloth is supplied.After the paint
has dried, apply a light coat of spray adhesive to
the inside of the perforated grille and attach a new
scrim cloth.

5. Remove the paint shield from the baffle and
attach the grille.

LOUDSPEAKER
OUTPUT LEVELS

High-order filters result in steep cutoffs to reduce potential
damage from “out-of-band”frequencies. Combined
with custom-designed transducers and high-quality
filter network components, this approach helps the
IW65/80, IC6T2 and IC65/80 loudspeakers to maintain
their performance under extreme operating conditions.
However,all loudspeakers ha ve limits when it comes
to continuous playback.To extend these limits, avoid
playback at volume levels that result in distorted or
strained sound.

If a subwoofer is in use in the system, the in-wall or
in-ceiling loudspeakers should have crossovers at 80Hz
or above. Some A/V receivers or processors are set by
identifying the loudspeakers as “small.”

OBTAINING SERVICE

To obtain warranty or nonwarranty service,contact an
authorized Revel dealer.Refer to the included Revel
warranty card for warranty information.

12

Revel Concerta IW65/IW80&IC65/IC80/IC6T2

Owner’s Manual

Specification IW65 IW80 IC65 IC80 IC6T2

Frequency Response 50Hz to 40kHz, ±3dB 40 Hz to 40 kHz, ±3dB 50Hz to 40kHz, ±3dB 45Hz to 40kHz, ±3dB 55 Hz to 22 kHz, ±3dB
(2π anechoic)

Recommended Amplifier 10 – 125 Watts 10 – 135 Watts 10 – 125 Watts 10 – 135 Watts 10 – 125 Watts
Power Range (Total)

Sensitivity 89dB 89dB 89dB 89dB 88dB
(2.83V ,2π anechoic) (Both channels driven)

Nominal Impedance 8 Ohms 8 Ohms 8 Ohms 8 Ohms 6 Ohms
Crossover Frequency 3,000Hz; 24dB/Octave 2,400Hz; 18dB/Octave 2,500Hz; 18dB/Octave 2,500Hz;18dB/Octave 2000Hz; 24dB/Octave
Low-Frequency Driver 6-1/2" (165mm) Micro 8" (200mm) Micro 6-1/2" (165mm) Micro 8" (200mm) Micro 6-1/2" (165mm) Micro

Ceramic Composite Ceramic Composite Ceramic Composite Ceramic Composite Ceramic Composite

(MCC) cone (MCC) cone (MCC) cone (MCC) cone (MCC) cone

High-Frequency Driver 1" (25mm) Micro 1" (25mm) Micro 1" (25mm) Micro 1" (25mm) Micro Dual 3/4" (19mm) Micro

Ceramic Composite Ceramic Composite Ceramic Composite Ceramic Composite Ceramic Composite

(MCC) dome (MCC) dome (MCC) dome (MCC) dome (MCC) domes

External Dimensions 8-1/2" x 11" 10-1/4" x 13-7/16" Diameter: 9-1/4" Diameter:10-7/8" Diameter: 9-1/4"
(W x H) (216mm x 280mm) (259mm x 341mm) (235mm) (275mm) (235mm)

Mounting Cutout Size 7" x 9-1/2" 8-3/4" x 11-3/4" Diameter: 7-7/8" Diameter: 9-1/2" Diameter:7-7/8"
(W x H) (178mm x 241mm) (221mm x 297mm) (200mm) (241mm) (200 mm)

Mounting Depth 3-1/2" (89mm) 4" (102mm) 4-1/8" (104mm) 4-3/4" (121mm) 4-1/8" (104mm)
Recommended Optimum Infinite Baffle 88 liters Infinite Baffle 88 liters Infinite Baffle

Enclosure Volume (full stud bay) (full stud bay) (full stud bay)
Weight (Net) 3.5 lb (1.6kg) 5.9 lb (2.7kg) 3.5 lb (1.6kg) 5.8 lb (2.6kg) 3.5 lb (1.6kg)

SPECIFICATIONS

Specifications are subject to change without notice.

Declaration of Conformity

We, Harman Consumer Group, Inc.

2, route de Tours
72500 Ch

â

teau du Loir

France

declare in own responsibility that the products described

in this owner’s manual are in compliance with technical

standards:

EN 61000-6-3:2001

EN 61000-6-1:2001

Laurent Rault

Harman Consumer Group, Inc.

Ch

â

teau du Loir, France 7/08

13

Revel Concerta IW65/IW80&IC65/IC80/IC6T2
Owner’s Manual

A valid serial number is required for warranty coverage.This
Revel warranty protects the original retail purchaser for a
period of five (5) years (parts and labor) from any failure as
a result of original manufacturing defects, so long as:

1.The Revel products were purchased within the 50 United

States, its territories or Canada.

2.The dealer from whom the Revel products were

purchased was authorized to sell such products at the
time of the original purchase.

3.The original, dated Bill of Sale is presented whenever

service is required during the warranty period.

The balance of this warranty is transferable only if the used
product is purchased from an authorized Revel dealer.This
warranty is only valid for service within the United States, its
territories and Canada; please contact an authorized Revel
dealer for warranty and service information.

Any Revel product not performing satisfactorily may be
returned to the factory for evaluation. Return authorization
must first be obtained by either calling or writing Customer
Service prior to shipping the product.The customer is
responsible for shipping charges to the factory.Customer

Service will pay return shipping charges within the United
States only in the event that the product is found to be
defective, as mentioned above. There are other stipulations
that may apply to shipping charges.

There is no other express warranty on this product. Neither
this warranty nor any other warranty,express or implied,
including implied warranties of merchantability and fitness,
shall extend beyond the warranty period. No responsibility is
assumed for any incidental or consequential damages, so
that the above exclusion or limitation may not apply.

This warranty provides specific legal rights. Other states may
provide additional rights.This warranty is applicable in the
United States, its territories and Canada. Outside of the
United States, its territories and Canada, please contact an
authorized Revel dealer for warranty and service information.
The information this document contains is subject to change
without notice. In the event that there are differences between
this warranty and the provisions of any advertisements,
documentation, product brochures or packaging cartons,
the terms of this warranty will prevail.

For customer service and product shipment information,
go to www.revelspeakers.com.

LIMITED WARRANTY

For customer service and product shipment information,
go to www.revelspeakers.com.

Part No.406-000-05627-E Rev 2
©2008 Harman International Industries, Incorporated.

All rights reserved.

Revel, the Revel logo and Concerta are trademarks
of Harman International Industries, Incorporated, in
the United States and/or other countries.

Features, specifications and appearance are subject
to change without notice.