B112/B110 Subwoofer
Quick Start Guide
TABlE Of CONTENTS
About Revel Performa3 Subwoofers........................................................................................................................................ 2
B112/B110 Overview ............................................................................................................................................................... 3
Subwoofer Placement Considerations..................................................................................................................................... 4
Placing Four Subwoofers, Placing Two Subwoofers, Placing a Single Subwoofer
Making Connections ................................................................................................................................................................ 6
Connecting to a Surround Processor with an Internal Crossover, Connecting to a Stereo Preamplifier,
Connecting Multiple Subwoofers, Trigger and Power Connections
Caring for Your Subwoofer.....................................................................................................................................................10
Specifications ......................................................................................................................................................................... 10
Warranty ................................................................................................................................................................................ 11
ABOUT THIS DOCUMENT
This quick-start guide contains all the information you will need to
unpack and initially place your Revel Performa3 subwoofer, connect it to
the rest of your audio system, turn it on and have a first listen. To take
full advantage of all the performance your new subwoofer is capable of
delivering, please go to the Revel Web site (www.revelspeakers.com)
and download the free Revel Performa3 Subwoofer User Guide and the
Revel LFO (Low-Frequency Optimization) software. The User Guide and
software provide you with an extremely sophisticated way to optimize
your subwoofer’s performance for your particular installation.
ABOUT REvEl PERfORMA3 SUBwOOfERS
Thank you for purchasing a Revel Performa3 subwoofer. The B112
and B110 are powered by a 1,000-watt RMS (2,000-watt peak)
internal amplifier and feature a custom-designed transducer that
combines a new level of low frequency nuance and refinement with
unprecedented brute-force capabilities in a unit designed for use in the
home. Combined with the internal amplifier’s large power capability,
and the extensive programming and room equalization capability of
the companion Revel LFO (Low-Frequency Optimization) programming
software, the result is a new standard of superb bass performance and
adaptability for home entertainment systems.
The B112 and B110 feature 12-inch and 10-inch versions, respectively, of
a brand-new low-frequency transducer that has been designed specifically
for use in these two subwoofer models. The primary design goal for this
new driver was to produce very low frequencies at extremely high SPL
(sound-pressure levels) while at the same time maintaining extremely low
distortion – requirements that usually remain mutually exclusive. This new
unit maintains a precise engineering balance between the voice coil, spider
and surround that produces linear motion of all three for lower distortion by
incorporating CAD/FEA optimized high-linearity motor geometry:
• The extremely long (50mm) two-layer copper voice coil gives this
transducer a very high Xmax, dramatically increasing output.
A fiberglass voice coil former helps the voice coil withstand
high temperatures, reducing power compression and helping
increase output. A spacer added at the top of the voice coil former
maintains motor geometry, creates a solid attachment joint and
prevents deformation of the voice coil at high outputs. The spacer
also eliminates the typical single fulcrum point between the spider
and cone on the voice coil former, minimizing voice coil rocking
modes during hi-power operation.
• A high-temperature Nomex
design that evenly distributes mechanical stress, helping keep the
cone’s motion linear during high-excursion operation.
• A nitril/butylene rubber surround uses patented Plus One
technology that increases the transducer’s radiating area (Sd),
increasing volume displacement and output.
®
spider features a progressive roll
®
The coated cellulose/pulp cone and dustcap assembly is vented under
the dustcap to aid in the exchange of air, which reduces acoustic losses
and increases output.
The transducer’s massive magnet assembly (30.6 lb in the B112; 24.3
lb in the B110) features a triple-stacked vented ceramic 5 magnet with
flared vents that reduce turbulence, which improves airflow, increases
output and reduces distortion. Dual symmetrical magnet shorting rings
and an extended top pole create a symmetrical magnetic gap field that
increases power handling and reduces power compression further
increasing output. A 15mm-thick top plate improves heat and flux
distribution for lower distortion.
The cast aluminum frame is fully vented to minimize acoustic losses
caused by excessive back pressure. This frame also maintains
dimensional stability and precise mechanical tolerances, allowing the
transducer to be manufactured and assembled to a high degree of
precision.
The B112 and B110 enclosures are formed with contiguous wood layers
that prevent splitting. They feature strategically-oriented bracing that
eliminates the possibility of enclosure-induced coloration. The beautiful,
modern enclosure is finished in high-gloss piano black or genuine
American walnut in a process (developed and overseen by Italian luxury
cabinet makers) that exceeds automotive finish quality.
Your Revel Performa3 subwoofer is designed to be used along with our
Revel LFO programming software, which is available as a free download
at www.revelspeakers.com. The software configures the DSP processor
inside your Performa3 subwoofer, which provides up to ten independent
equalization points, each with user-determined frequency, amount of
gain/cut and filter Q (bandwidth). This provides you with an extremely
sophisticated way to optimize the subwoofer’s performance for your
particular installation, listening room and seating arrangement. In
addition, the software also provides programming for the subwoofer’s
internal crossover system, as well as speaker delay and polarity
settings. All of these processing options can also be independently
applied to the subwoofer’s left and right high-pass outputs.
During development, every Revel loudspeaker model is compared to
competitive models in our unique position-independent double-blind
listening lab. This process utilizes the latest psychoacoustic research
to assure that these listening tests are valid, enabling us to verify that
all Revel loudspeakers are superior to their competitors before they are
allowed to go into production.
2
B112/B110 Subwoofer
Quick Start Guide
B112/B110 OvERvIEw
(Note: B112 and B110 rear panels are identical.)
Power Switch
Power Cord Connector
Subwoofer Out Connector (Balanced)
Subwoofer Out Connector (Unbalanced)
High-Pass Out Connectors (Balanced)
High-Pass Out Connectors (Unbalanced)
Input Connectors (Unbalanced)
Input Connectors (Balanced)
12V Trigger In/Out Connectors
USB Connector
Subwoofer Gain Control
Power Mode Switch
Subwoofer Out connectors: If you are using more than one Performa3
subwoofer in the system, connect the Subwoofer Out connector to
the additional Performa3 subwoofer’s Input Connector. Balanced (XLR)
and unbalanced (RCA) connectors are available. Both outputs are 0dBv
(nominal)/+20dBv (maximum). The XLR output is pin 2 high.
High-Pass Out connectors: Use these connectors to send a high-pass
filtered signal to the main (left/right) amplifier’s inputs. Balanced (XLR)
and unbalanced (RCA) connectors are available. Both outputs are 0dBv
(nominal)/+20dBv (maximum). The XLR output is pin 2 high. NOTE: The
factory-default high-pass crossover setting is at 80Hz with a 24dB/octave
(4th-order) slope. You can change these settings using the Revel LFO
programming software. See the Revel Performa3 Subwoofer User Guide
for more information.
Input connectors: Connect these to the outputs of a stereo preamp or
connect a surround processor's subwoofer output to either the left or right
input. Balanced (XLR) and unbalanced (RCA) connectors are available. Both
inputs are 0dBv (nominal)/+20dBv (maximum). The XLR input is pin 2 high.
12V Trigger In/Out connectors: When the subwoofer’s Power Mode
Switch is set to “Trigger,” the subwoofer will automatically turn on when
5V – 12V is present at the 12V Trigger In connection and will turn off when
the voltage at this connection is removed. Whenever the subwoofer is on,
a 12V trigger signal is available at its 12V Trigger Out connector for use
with additional Performa3 subwoofers, or another triggerable device.
USB connector: To program the subwoofer’s room equalization and
high-pass and low-pass crossover characteristics, connect this USB Type
B receptacle to the USB receptacle of a computer that is running the Revel
LFO programming software.
Subwoofer Gain control: Use this control to adjust the volume of the
subwoofer relative to the system’s other speakers. (The Gain control can
be disabled using the Revel LFO programming software.)
Power Mode switch: This switch determines how the subwoofer will
turn on and off:
• When this switch is set in the “Auto” position and the Power switch
is set to “On,” the subwoofer will automatically turn on when it first
detects an audio signal at any of its inputs, and will automatically
enter the standby mode after it has received no audio signal for a
period of time (30 seconds to 120 minutes) you can set using the
Revel LFO programming software.
• When this switch is set in the “On” position, the subwoofer will turn
on when the Power switch is set to “On” and will remain on until the
Power switch is set to “Off.”
• When this switch is set in the “Trigger” position and the Power
switch is set to “On,” the subwoofer will automatically turn on when
a voltage is present at the 12V Trigger In connection and will remain
on as long as the voltage is present. When the voltage at the 12V
Trigger In connection is removed the subwoofer will automatically
turn off.
Power switch: When this switch is set to “On,” the subwoofer’s on/off
status is dependent on the setting of the Power Mode switch (see above).
When the Power switch is set to “Off” the subwoofer is turned off and
cannot turn on automatically.
We suggest setting the Power switch in the “Off” position if you will not
be using the subwoofer for a long period of time, such as when you’re on
vacation.
Power Cord connector: Plug the supplied power cord into this
connector and into a working unswitched AC power outlet.
B112/B110 Subwoofer
Quick Start Guide
3
SUBwOOfER PlACEMENT
CONSIDERATIONS
When using subwoofers within the limited confines of a typical home
theater room, the reflections, standing waves and absorptions generated
within the room will create peaks and dips in the bass response that
can vary greatly depending on where the listeners are located in the
room – a listener seated in one location may hear an overabundance of
bass created by a response peak at that location, while another listener
only a few feet away may hear a considerable lack of bass created by a
response dip at that location.
The subwoofers’ locations within the room (along with the room’s
dimensions) also have a profound effect on the creation of these bass
response peaks and dips. Careful subwoofer placement alone cannot
compensate for all bass response peaks and dips throughout a room, but
careful subwoofer placement can eliminate or significantly reduce the
largest response dips.
It is important to reduce response dips throughout the room as much as
possible via proper subwoofer placement because equalization cannot
be used to compensate for large response dips. For example, using
equalization in an attempt to restore a 13dB response dip requires
that the subwoofer amplifier delivers twenty times the power at that
frequency. This can quickly overdrive the subwoofer amplifier into
clipping, which will significantly degrade audio quality.
In almost any room, placing the subwoofers in corners will produce the
fewest large bass response dips and will also produce the most large
bass response peaks. With the subwoofers so placed, you can then use
the Revel LFO programming software’s sophisticated room equalization
capability to compensate for the response peaks, resulting in superb
bass performance.
We strongly recommend that you install multiple subwoofers regardless
of the room’s size. Even after using the Revel LFO programming
software’s room equalization to remove the response peaks, installing
a single subwoofer will result in the least consistent bass performance
throughout the room. Using multiple subwoofers can cancel some
room modes at the various listening locations, resulting in much
more consistent low frequency sound quality throughout the listening
area. Additionally, it is often impossible to locate a single subwoofer
such that large response dips, which cannot usually be corrected via
equalization, are not present. The use of two or more properly placed
subwoofers can almost always eliminate such dips in response.
PlACINg fOUR SUBwOOfERS
When installing four subwoofers, place each one in a room corner. In
rooms with more than four corners, use the four corners closest to the
listening area.
Video Screen
PlACINg TwO SUBwOOfERS
Placement of two subwoofers will be determined by your room’s seating
arrangement.
Rooms with a single row of seating
Placing the subwoofers in the two front corners will produce the most
consistent bass performance throughout a single row of seating.
Video Screen
4
B112/B110 Subwoofer
Quick Start Guide
Rooms with multiple seating rows
Placing one subwoofer in a front corner and the other subwoofer in the
rear corner on the same side will produce the most consistent bass
performance throughout multiple seating rows.
Video Screen
PlACINg A SINglE SUBwOOfER
When installing a single subwoofer, be prepared to experiment with
different locations to find the one that produces the best results
throughout your room’s seating area. As in the previous examples,
placing the subwoofer in a corner will produce the fewest number of
deep response dips, which cannot be corrected with equalization.
Video Screen
We strongly suggest performing measurements (beginning by
performing measurements with at least 1/12th-octave resolution)
with the subwoofer in each of the room’s corners to find the one that
produces the most consistent results at the various listening positions
in your room. Please see the Revel Performa3 Subwoofer User Guide for
information about performing in-room measurements.
Since wall construction is almost never perfectly identical on opposite
walls, common formulas such as placing the subs at 1/4 points
rarely work in practice. The best solution is to make high-resolution
measurements from the primary listening area while experimenting with
speaker placement.
B112/B110 Subwoofer
Quick Start Guide
5
MAkINg CONNECTIONS
CAUTION: Never make or break connections unless all
system components are powered off.
CONNECTINg TO A SURROUND PROCESSOR wITH AN
INTERNAl CROSSOvER (fACTORy-DEfAUlT)
If you are connecting to a surround processor with a low-pass filtered
subwoofer output, connect the subwoofer as shown below. You can
make either a balanced (XLR) or unbalanced (RCA) connection to
either the subwoofer’s left or right input connector. To accommodate
connection to surround processors with internal crossovers, the B112
and B110 are factory-programmed with their low-pass and high-pass
crossover circuits disabled.
B112/B110
Connectors
Surround Processor
Line Outputs
Use either
connector
OR
Use either
connector
6
B112/B110 Subwoofer
Quick Start Guide
CONNECTINg TO A STEREO PREAMPlIfIER
If you are connecting to a stereo preamplifier, connect the subwoofer as
shown below. You can make either balanced (XLR) or unbalanced (RCA)
connections between the preamp and subwoofer, and between the
subwoofer and the left/right power amplifier.
Using this connection method, you must use the Revel LFO programming
software to enable the subwoofer’s internal crossover circuits, which
can provide a high-pass filtered signal to the power amplifier for the
left/right speakers via the subwoofer’s left/right High-Pass outputs.
The Revel LFO programming software provides the same sophisticated
room equalization capability for the subwoofer’s left and right High-Pass
outputs as it does for the subwoofer itself, allowing you to optimize your
system’s performance to an unprecedented degree.
Stereo Power Amplifier
B112/B110
Connectors
OR
OR
OR
Stereo Preamplifier
OR
To
Left and Right
Speakers
B112/B110 Subwoofer
Quick Start Guide
7
CONNECTINg MUlTIPlE SUBwOOfERS
When installing more than one Performa3 subwoofer, connect the
first one as shown in the appropriate example above. Connect the
additional subwoofers in “daisy-chain” fashion, using the Subwoofer
Out connectors and Input connectors, as shown below.
First
B112/B110
B112/B110
Connectors
NOTE: Read the Revel Performa3 Subwoofer User Guide for
information about settings in the Revel LFO programming software
that are required when using multiple subwoofers.
OR
From Surround
OR
Processor or
Preamplifier
Additional
B112/B110
B112/B110
Connectors
Use either
connector
OR
Use either
connector
8
B112/B110 Subwoofer
Quick Start Guide
TRIggER AND POwER CONNECTIONS
Trigger In/Out Connectors
If you want your subwoofer(s) to turn on along with another component
that supplies a trigger voltage, use a mono 3.5mm cable (not supplied)
to connect the 12V DC Trigger In connector to the trigger voltage out
connector of the other component.
To supply a trigger signal to an additional Performa3 subwoofer (or
other triggerable device), use a mono 3.5mm cable (not supplied)
to connect the 12V DC Trigger Out connector of the first Performa3
subwoofer to the 12V DC Trigger In connector of the next Performa3
subwoofer. Connect additional Performa3 subwoofers this way, in
“daisy-chain” fashion.
NOTE: When using the 12V DC Trigger connectors, set the
subwoofers’ Power Mode switches in the “Trigger” position.
Power Cord
After you have ensured that all connections have been correctly made,
plug the supplied power cord into the subwoofer’s Power Cord connector
and into a working unswitched AC power outlet.
Power Cord
Connector
AC Power
Outlet
B112/B110
Connectors
B112/B110
B112/B110 Subwoofer
Quick Start Guide
Power Cord
(supplied)
To 5V – 12V
Trigger Source
To “Trigger In”
Connector on Additional
Performa3 Subwoofer
9
CARINg fOR yOUR SUBwOOfER
The cabinet’s wood veneer finish does not require routine maintenance.
Cabinet surfaces that have been marked with dust, fingerprints, or other
dirt can be cleaned using a soft cloth – preferably microfiber, and highquality auto wax. Take care not to come in contact with the transducer.
• Use caution to avoid contacting the rubberized trim on the top of
the loudspeaker with auto wax. If necessary, the rubberized trim
can be cleaned with denatured alcohol on a microfiber cloth.
To clean the grille, gently vacuum it using a soft-bristled brush vacuum
attachment with the vacuum cleaner set to the lowest possible suction.
CAUTION: To prevent cabinet damage, do not use metal
polish or a cloth made with steel wool to clean the
cabinet. To prevent possible transducer damage, do not
apply furniture polish directly to the cabinet.
SPECIfICATIONS
B112/B110
Type: Powered subwoofer
Low-frequency transducer: Coated paper/pulp cone (12” – B112; 10” – B110) with 50mm two-layer copper voice coil,
Amplifier power: 1,000 watts (RMS), 2,000 watts (peak)
Input sensitivity/impedance: 400mV (full power)/20k ohms (balanced); 14k ohms (unbalanced)
Crossover frequency: 50Hz – 200Hz, independent low-pass and high-pass 1st-, 2nd-, 4th-, 8th-order Butterworth,
Enclosure type: Sealed
Inputs: Balanced (XLR); unbalanced (RCA)
Available finishes: Piano black; high-gloss genuine American walnut veneer
Dimensions (H x W x D):
B112:
B110:
Weight:
B112:
B110:
vented triple-stacked ceramic 5 magnet assembly and vented die-cast aluminum frame
4th- or 8th-order Linkwitz-Riley (factory-disabled, user-programmable with Revel LFO
programming software)
18-7/16" x 15-15/16" x 16-9/16" (468mm x 404mm x 420mm), with grille
16-7/8" x 14-5/16" x 13-7/16" (428mm x 364mm x 342mm), with grille
70.4 lb (31.9kg)
56 lb (25.4kg)
10
B112/B110 Subwoofer
Quick Start Guide
wARRANTy
Revel Series speakers are warranted against defects. The duration of the speaker’s warranty depends on the laws in the country in which it was
purchased. Your local Revel retailer can help you determine the length of your warranty.
HARMAN International Industries, Incorporated
8500 Balboa Boulevard, Northridge, CA 91329 USA
© 2013 HARMAN International Industries, Incorporated. All rights reserved.
Revel and the Revel logo are trademarks of HARMAN International Industries, Incorporated,
registered in the United States and/or other countries.
Nomex is a registered trademark of E. I. du Pont de Nemours and Company.
Features, specifications and appearance are subject to change without notice.
For questions, assistance or additional information concerning any of our products,
call us at: (516) 594-0300 or (888) 691-4171. For technical support, submit your
detailed inquiry to: csupport@harman.com.
Part No. REVP5250 Rev: A
www.revelspeakers.com
Loading...