Quick Start Guide
Wirefree Remote Monitoring/
Communicating Intruder Alarm System
GSM/SMS/RFID/Touch Control
G5
Technical Support Helpline:
0845 373 1353
lines open 0900 to 1700 Monday to Friday
Congratulations on your purchase of the miGuard G5
Remote Monitoring/Communicating Intruder Alarm System
CONTROL PANEL SIM CARD
IMPORTANT NOTES
to be read prior to system set-up
1. Prior to setting up your G5 system you must:
a. Have available a mobile phone together with either a PAYG or Contract
regular size SIM Card, on the network of your choice
(important: check with your network provider that the SIM Card is 2G enabled)
b. Know the SIM Card telephone number
c. Ensure the SIM Card has available credit
d. Turn off/disable the voicemail function and PIN request
NOTE:
A SIM Card is required to program the alarm panel from your mobile phone (This may take
as many as 25 text inputs and a further 25 text replies). Once programmed, the SIM Card can
be removed from the alarm panel if the remote phone functions are not required.
Please consider that most mobile tariffs include free texts or a generous monthly allowance
(you will not need any data allowance).
I. Installing the Control Panel
1. Carefully remove the battery cover at the back
of the unit using a flat-bladed screwdriver.
2. Plug the power socket into the unit and Power
Supply/plug into a suitable 13 amp socket.
3. Insert a standard size SIM Card (with credit) into the SIM
Card holder.
4. Set the unit’s ‘ON/OFF’ Switch to ‘ON’.
5. Refit the battery cover, ensuring the power supply cable
sits within the channel and exits through the top of the
battery compartment.
6. The GSM indicator (LED) will flash once every second for a short period and
will then flash once every two seconds indicating that the GSM signal has
been found. You can now register your mobile phone to the Control Panel.
If the LED flashes every second (GSM signal not found) power down the
Control Panel, remove the SIM Card and wait 30 seconds. Insert the SIM
Card again and allow 1 minute for the signal to be found, indicated by
a flash once every 2 seconds.
7. Follow steps II to IV to install/set-up the accessories.
1 x Control Panel
1 x PIR Motion Detector
1 x Door/Window Contact
2 x Remote Controls
2 x RFID Tags
1 x AC/DC Adapter
All Batteries & Fittings
Instruction Manual
Kit Contents:
a. Read the instructions thoroughly
b. Remove all the contents from their packaging
c. Have a flat-bladed screwdriver to hand
d. Consider the most appropriate positioning of
the Control Panel and each Accessory
Note: The Accessories are pre-programmed to
the Control Panel for ease of installation
Prior to setting up your System:
OFF
ON
MiGuard is a trademark of Response Electronics Limited
Refer to the system’s full instruction manual for detailed programming
1. Open the battery compartment cover using a flat-bladed screwdriver and
remove the activation strip.
2. Self-testing will commence once the battery activation strip is removed.
Flashing continuously = self testing state. Flashing once indicates that
movement is detected.
3. Fit the detector in a position that will cover your desired protection area,
orientation as per diagram opposite.
4. To test, walk in front of the detector - the LED should illuminate.
When in its working state, if the detector is triggered more than twice in
3 minutes, it will enter into power saving (sleep mode). If no movement
is detected within the next 3 minutes, the detector will return to normal
working mode.
1. Slide down the battery compartment cover using a flat-bladed
screwdriver and remove the activation strip.
2. Remove one side of the double-sided tape and fix the tapes to the
back of the Magnet and Transmitter.
3. Remove the paper strips and mount the magnet on the door and the
transmitter on the door jamb (small triangles adjacent to each other)
with less than a 6 mm separation between the two. When opening the
door a small red indicator lights up briefly, this indicates that the
Transmitter has sent the signal to the Control Panel.
The system can be quickly disarmed by holding the RFID Tag to the RFID
reader.
II. Installing a Door/Window Contact
III. Installing a Wireless PIR
IV. Remote Control Operation
V. RFID Tag Operation
1. Press the Arm Button on the Remote Control
2. The Control Panel will sound every 2 seconds to indicate that it is armed,
allowing 30 seconds to exit the premises.
3. The sound will intensify in tempo for the last 15 seconds to warn that
system activation is imminent.
www.responseelectronics.com
Response Electronics Ltd., Roman House, Lysons Avenue, Ash Vale, Surrey, GU12 5QF
email: info@responseelectronis.com
Loading...