Respironics REMstar Pro M Series User Manual
10164 44
JH 2/ 14/0
6
USE R M ANU AL
e REMstar® Pro M Series with C-Flex™ system is covered by one or more of the following patents:
5,148,802; 5,313,937; 5,433,193; 5,632,269; 5,803,065; 6,029,664; 6,305,374; 6,539,940, 5,535,738;
5,794,615; 6,105,575; 6,609,517; 6,629,527; 6,622,724; 6,564,797; 6,427,689, and 6,932,084. Other
patents pending. REMstar, Whisper Swivel, Encore Pro, and Encore Pro SmartCard are trademarks of
Respironics, Inc. NOTE: e C-Flex mark is used under license.
© 2006 Respironics, Inc. All rights reserved.
IMPORTANT! Fill in the information below when you receive the REMstar
®
Pro M Series system.
Serial No.: _______________________________ (located on the bottom of the device)
System Prescribed for: __________________________________________
Date of Purchase or Rental: ______________________________________
Pressure Setting: _____ cm H
2
O
Mask Ty
pe: __________________________________________________
Mask Size: ___________________________________________________
If you have any questions
concerning the system, contact:
• Home Care Company: _______________________________________
Telephone Number: _________________________________________
• Health Care Professional: _____________________________________
Telephone Number: _________________________________________
• Respironics, Inc.
1001 Murry
Ridge Lane
Murrysville, Pennsylvania
15668-8550 USA
Customer Service
Telephone Number: 1-724-387-4000
Name
Address
City State Zip
Phone ( )
E-mail
Where did you first hear about your M Series device?
Homecare Provider Sleep Lab Internet/Website Tradeshow
Friend/Colleague
Other (please specify)
Would you like to receive information regarding new products from Respironics?
Yes No
Product Identification Information
(Numbers located on the bottom
of the device)
Model #:
Serial #:
Please complete the following or register online at:
www.mseries.respironics.com
®
If Yes, Preferred Method?
Direct Mail
Phone
Email
C
M
Y
CM
MY
CY
CMY
K
reply_card2.pdf 9/19/05 11:22:20 AMreply_card2.pdf 9/19/05 11:22:20 AM
PO BOX 7014
GRAND RAPIDS MN 55744-8029
FIRST-CLASS MAIL PERMIT NO. 231 GRAND RAPIDS MN
C
M
Y
CM
MY
CY
CMY
K
reply_card1.pdf 9/19/05 10:52:10 AMreply_card1.pdf 9/19/05 10:52:10 AM
An application to join the American Sleep Apnea Association should be attached here.
If it is not, you can contact the American Sleep Apnea Association at 1-202-293-3650.
Name ______________________________________________ Phone No. ( ) ___________________________
Address _________________________________ City ____________________ State _________ Zip ___________
Please check: _____$1000 _____$500 _____$250 _____$100 _____$50 _____$25 annual membership*
All memberships include a one year subscription to the newsletter. Membership and contributions are deductible for income tax
purposes within IRS rules.
Respironics, Inc. provided a grant to and is recognized as a founding sponsor of the American Sleep Apnea Association. As a
non-profit organization, the American Sleep Apnea Association does not endorse or recommend any company or product.
Membership includes a free medical alert necklace or bracelet.
_____I would like to become a member of the ASAA.
Please send me a free medical alert _____bracelet or _____necklace.
_____I am undecided, but please send me a free copy of the newsletter.
_____I would like to know if there is an A.W.A.K.E. group near me.
PLEASE SEND TO:
American Sleep Apnea Association
1424 K Street NW, Suite 302, W
ashington D.C. 20005
*For addresses outside the United States, the minimum contribution is U.S. $50.00.
Join the American Sleep Apnea Association
As a member of the American Sleep Apnea Association, you will receive a newsletter, WAKE-UP CALL,
six times each year. This newsletter will inform you about the latest in medical advances, new technology,
human interest stories of individual accomplishment, home care tips, and legislative affairs. Also, you will
receive a medical alert identification bracelet.
You are also invited to participate in the A.W.A.K.E. (Alert, Well And Keeping Energetic) Network, which
is a nationwide system of local mutual help/support groups. A.W.A.K.E. meetings provide the opportunity
to share information and support with others who have been affected by sleep apnea.
G O A L S
To reduce disability and
death from Sleep
Apnea and other
breathing disorders
during sleep.
To improve the clinical
care of Sleep Apnea by
educating the public and
medical profession
about the disorder.
To provide Sleep
Apnea sufferers with
information about new
advances in the treatment
of Sleep Apnea.
To establish and
nurture mutual
help/support groups
for apnea sufferers
and their families.
To raise money for
and to sponsor
research on the
causes and treatment
of Sleep Apnea.
iREMSTAR PRO M SERIES USER MANUAL
TABLE OF CONTENTS
Chapter 1: Introduction ..................................................................................................................1-1
1.1 System Contents ........................................................................................................1-1
1.2 Intended Use ...............................................................................................................1-2
1.3 Warnings, Cautions, and Contraindications .....................................................1-2
1.3.1 Warnings ...........................................................................................................1-2
1.3.2 Cautions ............................................................................................................1-4
1.3.3 Contraindications ..........................................................................................
1-4
1.4 System Overview ....................................................................................................... 1-5
1.4.1 Breathing Circuit Overview ........................................................................1-7
1.5 Glossary .........................................................................................................................1-8
1.6 Symbol Key ..................................................................................................................
1-9
1.7 How to Contact Respironics ............................................................................... 1-10
Chapter 2: Device Controls and Displays .................................................................................2-1
2.1 Controls and Displays ..............................................................................................2-1
2.1.1 Control Panel Inactivity ...............................................................................2-3
2.2 Rear Panel .....................................................................................................................2-3
Chapter 3: Setup ................................................................................................................................
3-1
3.1 Installing the Air Filters ............................................................................................3-1
3.2 Where to Place the Device ......................................................................................3-2
3.3 Connecting the Breathing Circuit .......................................................................
3-2
3.4 Supplying Power to the Device ............................................................................3-5
3.4.1 Using AC Power .............................................................................................3-5
3.4.2 Using DC Power .............................................................................................
3-6
3.5 Complete Assembly Example ...............................................................................3-7
Chapter 4: Device Operation ........................................................................................................
4-1
4.2 Using the Ramp and C-Flex Features .................................................................4-3
4.2.1 Ramp Feature ..................................................................................................4-3
4.2.2 C-Flex Comfort Feature ...............................................................................
4-4
4.2.2.1 C-Flex Enabled ....................................................................................4-4
4.2.2.2 C-Flex Disabled ..................................................................................4-4
ii REMSTAR PRO M SERIES USER MANUAL
4.3 Changing the Device Settings ..............................................................................4-5
4.3.1 Navigating the Display Screens ...............................................................4-6
4.3.1.1 Viewing Data on the Patient Data Screens ...............................4-6
4.3.1.2 Viewing and Modifying Patient Setup Screens ......................4-8
4.4 Completing the FOSQ Questionnaire ..............................................................4-11
4.5 Patient Reminder Screen ......................................................................................4-12
Chapter 5: Device Alerts and Troubleshooting ......................................................................
5-1
5.1 Device Alerts ...............................................................................................................5-1
5.2 Troubleshooting .........................................................................................................5-4
Chapter 6: Accessories ....................................................................................................................6-1
6.1 Adding a Humidifier .................................................................................................
6-1
6.2 Using the SmartCard ..............................................................................................6-2
6.3 Adding Supplemental Oxygen ............................................................................. 6-2
Chapter 7: Cleaning and Maintenance .....................................................................................7-1
7.1 Cleaning the Device .................................................................................................7-1
7.2 Cleaning or Replacing the Filters .........................................................................7-1
7.3 Cleaning the Tubing .................................................................................................
7-3
7.4 Service ...........................................................................................................................7-3
7.5 Traveling with the System ......................................................................................7-4
7.5.1 International Travel ....................................................................................... 7-4
Chapter 8: Specifications ................................................................................................................
8-1
Appendix A: EMC Information .....................................................................................................A-1
1-1REMSTAR PRO M SERIES USER MANUAL
CHAPTER 1: INTRODUCTION
is chapter provides information on:
• REMstar Pro M Series system contents
• Intended Use
• Warnings, cautions, and contraindications
• System overview
• Glossary and symbol key
• How to contact Respironics
1.1 SYSTEM CONTENTS
Your REMstar Pro M Series system includes the following items:
REMstarPro M Series Device
Flexible Tubing
Reusable Gray Foam
Filter
Disposable Ultra-fine
Filter
Power Supply
AC Power Cord
Carrying Case
User Manual
Quickstart Guide
C
-F
le
x
FIGURE 1–1 SYSTEM CONTENTS
Note: If your system includes a humidifier, you will receive additional items with your
package. See the instructions included with your humidifier for more information.
Note: If any of the above items are missing, contact your home care provider.
1-2 REMSTAR PRO M SERIES USER MANUAL
1.2 INTENDED USE
e Respironics REMstar Pro M Series system is a CPAP (Continuous Positive Airway Pressure)
device designed for the treatment of Obstructive Sleep Apnea only in spontaneously breathing
patients weighing >66 lbs (30 kg).
e device is to be used only on the instruction of a licensed physician. Your home care provider
will make the correct pressure settings according to your health care professional’s prescription.
Several accessories are available to make your OSA treatment with the REMstar Pro M Series
system as convenient and comfortable as possible. To ensure that you receive the safe,
effective therapy prescribed for you, use only Respironics accessories.
1.3 WARNINGS, CAUTIONS, AND CONTRAINDICATIONS
Caution: U.S. federal law restricts this device to sale by or on the order of a physician.
1.3.1 WARNINGS
A warning indicates the possibility of injury to the user or the operator.
• is manual serves as a reference. e instructions in this manual are not intended to supersede the health care professional’s instructions regarding the use of the device.
• The operator should read and understand this entire manual before using the device.
• is device is not intended for life support.
• e device should be used only with masks and connectors recommended by Respironics
or with those recommended by the health care professional or respiratory therapist. A mask
should not be used unless the device is turned on and operating properly. e exhalation
port(s) associated with the mask should never be blocked.
Explanation of the Warning: e device is intended to be used with special masks or connectors that have exhalation ports to allow continuous flow of air out of the mask. When the
device is turned on and functioning properly, new air from the device flushes the exhaled air
out through the mask exhalation port. However, when the device is not operating, enough
fresh air will not be provided through the mask, and exhaled air may be rebreathed. Rebreathing of exhaled air for longer than several minutes can in some circumstances lead to
suffocation.
• If oxygen is used with the device, the oxygen flow must be turned off when the device is not
in use.
Explanation of the Warning: When the device is not in operation and the oxygen flow is left
on, oxygen delivered into the tubing may accumulate within the device’s enclosure. Oxygen
accumulated in the device enclosure will create a risk of fire.
1-3REMSTAR PRO M SERIES USER MANUAL
• Oxygen supports combustion. Oxygen should not be used while smoking or in the presence
of an open flame.
• When using oxygen with this system, a Respironics Pressure Valve (Part Number 302418)
must be placed in-line with the patient circuit. Failure to use the pressure valve could result
in a fire hazard.
• Do not use the device in the presence of a flammable anaesthetic mixture in combination
with oxygen or air, or in the presence of nitrous oxide.
• Do not use this device if the room temperature is warmer than 95° F (35° C). If the device is
used at room temperatures warmer than 95° F (35° C), the temperature of the airflow may
exceed 106° F (41° C). is could cause irritation or injury to your airway.
• Do not operate the device in direct sunlight or near a heating appliance because these conditions can increase the temperature of the air coming out of the device.
• Contact your health care professional if symptoms of sleep apnea recur.
• If you notice any unexplained changes in the performance of this device, if it is making unusual or harsh sounds, if the device or the power supply are dropped or mishandled, if water
is spilled into the enclosure, or if the enclosure is broken, discontinue use and contact your
home care provider.
• Repairs and adjustments must be performed by Respironics-authorized service personnel
only. Unauthorized service could cause injury, invalidate the warranty, or result in costly
damage.
• Periodically inspect electrical cords, cables, and the power supply for damage or signs of wear.
Discontinue use and replace if damaged.
• To avoid electric shock, unplug the device before cleaning it. DO NOT immerse the device
in any fluids.
• Pins of connectors identified with the ESD warning symbol ( )should not be touched.
Connections should not be made to these connectors unless ESD precautionary procedures
are used. Precautionary procedures include methods to prevent build-up of electrostatic
discharge (e.g., air conditioning, humidification, conductive floor coverings, non-synthetic
clothing), discharging one’s body to the frame of the equipment or system or to earth or a
large metal object, and bonding oneself by means of a wrist strap to the equipment or system
or to earth.
1-4 REMSTAR PRO M SERIES USER MANUAL
1.3.2 CAUTIONS
A Caution indicates the possibility of damage to the device.
• e device may only be operated at temperatures between 41° F (5° C) and 95° F (35° C).
• If this device has been exposed to either very hot or very cold temperatures, allow it to adjust
to room temperature before starting therapy. Condensation may damage the device.
• Do not immerse the device or allow any liquid to enter the enclosure or the inlet filter.
• A properly installed, undamaged reusable foam inlet filter is required for proper operation.
• Tobacco smoke may cause tar build-up within the device, which may result in the device
malfunctioning.
Note: Additional warnings, cautions, and notes are located throughout this manual.
1.3.3 CONTRAINDICATIONS
When assessing the relative risks and benefits of using this equipment, the clinician should
understand that this device can deliver pressures up to 20 cm H2O. In the event of certain fault
conditions, a maximum pressure of 30 cm H2O is possible. Studies have shown that the following
pre-existing conditions may contraindicate the use of CPAP therapy for some patients:
• Bullous Lung Disease
• Pathologically Low Blood Pressure
• Bypassed Upper Airway
• Pneumothorax
• Pneumocephalus has been reported in a patient using nasal Continuous Positive Airway Pressure. Caution should be used when prescribing CPAP for susceptible patients such as those
with: cerebral spinal fluid (CSF) leaks, abnormalities of the cribriform plate, prior history of
head trauma, and/or pneumocephalus. (Chest 1989; 96:1425-1426)
e use of positive airway pressure therapy may be temporarily contraindicated if you exhibit
signs of a sinus or middle ear infection. Not for use with patients whose upper airways are by
-
passed. Contact your physician if you have any questions concerning your therapy.
1-5REMSTAR PRO M SERIES USER MANUAL
1.4 SYSTEM OVERVIEW
e REMstar Pro M Series device, shown in Figure 1–2, is a sleep apnea system that
delivers Continuous Positive Airway Pressure (CPAP). CPAP maintains a constant level of pressure throughout the breathing cycle.
When prescribed for you, the device provides several special features to help make your therapy
more comfortable. e ramp function allows you to lower the pressure when you are trying to fall
asleep. e air pressure will gradually increase until your prescription pressure is reached. You also
have the option of not using the ramp feature at all.
Additionally, the C-Flex comfort feature provides you with pressure relief during the expiratory
phase of breathing
.
Several accessories are also available for use with your REMstar Pro M Series device. Contact your
home care provider to purchase any accessories not included with your system.
FIGURE 1–2 REMSTAR PRO M SERIES DEVICE
1-6 REMSTAR PRO M SERIES USER MANUAL
Figure 1–3 illustrates many of the device features, described in the table below.
Ramp Button
Start/Stop
Button
C-Flex
Button
Power Inlet
Filter Area
Air Outlet
Accessory
Module
Medical
Equipment Note
(on bottom)
Display Screen
(under door)
le
x
FIGURE 1–3 REMSTAR PRO M SERIES SYSTEM OVERVIEW
DEVICE FEATURE DESCRIPTION
Accessory Module If applicable, insert the optional accessory card here.
Air Outlet Connect the flexible tubing here.
C-Flex Button This button allows you to change the C-Flex comfort
setting, if C-Flex is prescribed for you. See Chapter 4
for more information about C-Flex.
Display Screen Shows therapy settings, patient data, instructions,
and error messages.
Filter Area A reusable, gray foam filter must be placed in the
filter area to screen out normal household dust and
pollens. An optional, white ultra-fine filter can also
be used for more complete filtration of very fine
particles.
Medical Equipment Note For ease at airport security stations, there is a note
on the bottom of the device stating that it is medical
equipment. It may help if you also take this manual
with you when you travel.
Power Inlet Connect the power cord here.
Ramp Button This button starts or restarts the ramp cycle.
Start/Stop Button This button starts or stops the airflow.
1-7REMSTAR PRO M SERIES USER MANUAL
1.4.1 BREATHING CIRCUIT OVERVIEW
e patient breathing circuit, shown in Figure 1–4, consists of the following:
• Circuit tubing to deliver air from the device to your interface (e.g., mask)
• A mask or other patient interface device to deliver the prescribed pressure to your nose or
nose and mouth, depending on which interface has been prescribed for you
• An exhalation device to vent exhaled air from the circuit
Circuit
Tubing
Exhalation
Device
Patient Interface
Circuit with Separate
Exhalation Device
Circuit with Mask with
Integrated Exhalation Port
Flexible
Tubing
Connector
Mask's
Connector
Exhalation
Port
FIGURE 1–4 TYPICAL BREATHING CIRCUITS
Note: The exhalation port may be part of the interface or may be part of a separate
exhalation device, but is required to minimize the potential for CO
2
rebreathing.
1-8 REMSTAR PRO M SERIES USER MANUAL
1.5 GLOSSARY
e following terms and acronyms appear throughout this manual:
TERM/ACRONYM DEFINITION
Active State The state of the device when power is applied, the airflow is on, and
the device is providing therapy.
Apnea A condition marked by the cessation of spontaneous breathing.
Auto-Off When this feature is enabled, the device automatically discontinues
therapy whenever the mask is removed.
Auto-On With this feature, the device automatically initiates therapy when you
begin breathing on the device. This feature is always enabled.
BPM Breaths Per Minute
C-Flex A therapy feature that provides pressure relief during exhalation, if
enabled by your home care provider.
CPAP Continuous Positive Airway Pressure
FOSQ Functional Outcomes of Sleep Questionnaire – A “quality of life” ques-
tionnaire designed specifically for people with sleep disorders. The
results allow health care professionals to assess how CPAP therapy has
improved the quality of their patients’ lives.
LPM Liters Per Minute
OSA Obstructive Sleep Apnea
Patient Data Menu The display mode in which you can view certain stored information,
such as therapy usage hours.
Patient Setup Menu The display mode in which you can change patient-adjustable device
settings, such as the ramp starting pressure.
Ramp A feature that may increase patient comfort when therapy is started.
The ramp feature reduces pressure and then gradually increases the
pressure to the prescription setting so you can fall asleep more comfortably.
Safe State The state in which the device does not provide therapy. The device
enters this state if an error is detected.
Standby State The state of the device when power is applied but the airflow is
turned off.
1-9REMSTAR PRO M SERIES USER MANUAL
1.6 SYMBOL KEY
e following symbols appear on the device and power supply:
SYMBOL DEFINITION
Consult accompanying instructions for use.
DC Power
Type BF Applied Part
Class II (Double Insulated)
IPX1
Drip Proof Equipment
Electrostatic Discharge
European Declaration of Conformity
Canadian/US Certification
Notified Body Approval for Standards Compliance
TUV Safety Standard Compliance
UL Recognized for Canada and the United States
No User Serviceable Parts
1-10 REMSTAR PRO M SERIES USER MANUAL
1.7 HOW TO CONTACT RESPIRONICS
To have your device serviced, contact your home care provider. If you need to contact Respironics
directly, call the Respironics Customer Service department at 1-800-345-6443 or 1-724-387-
4000. You can also use the following address:
Visit Respironics web site at: www.respironics.com
2-1REMSTAR PRO M SERIES USER MANUAL
CHAPTER 2: DEVICE CONTROLS AND DISPLAYS
is chapter describes the device’s control buttons and displays, patient circuit connections, and
rear panel connections.
2.1 CONTROLS AND DISPLAYS
Figure 2–1 shows the three primary control buttons on the REMstar Pro M Series device.
C-Flex
FIGURE 2–1 PRIMARY CONTROL BUTTONS
ese buttons are described below.
BUTTON DESCRIPTION
Ramp – When the airflow is on, this button allows you to
activate or restart the ramp function. Ramp lowers the
airflow pressure and then gradually increases it, allowing
you to fall asleep more easily.
Start/Stop – This button starts the device’s airflow and
places the device in the Active state, or stops the airflow,
and places the device in Standby. You can also press this
button to exit any setting screen.
C-Flex
C-Flex – This button adjusts the C-Flex comfort setting.
If you do not want to modify the settings that your home care provider has set for you, you only
need these three buttons to start and stop therapy and do not need to use the display buttons located under the device cover door.
Figure 2–2 shows the device display and navigation buttons that are under the cover door.
– FOSQ
+
Setup
FIGURE 2–2 DISPLAY BUTTONS
2-2 REMSTAR PRO M SERIES USER MANUAL
e display buttons are described below:
BUTTON DESCRIPTION
Allows you to access the Data screens. Also allows you
to navigate to the previous screen when in the Data or
Setup menu.
Allows you to access the Data screens. Also allows you
to navigate to the next screen when in the Data or
Setup menu.
Allows you to enter the FOSQ screens, and also allows
you to decrease the settings on the setup screens.
Allows you to enter the Setup screens. Also allows you
to increase the settings on the setup screens.
e device’s display screen shows the set pressure, patient data, instructions, and error messages.
See Chapter 4 for instructions on navigating the display screens.
Figure 2–3 provides a view of the entire device control panel, with the cover door open.
Cover Door
Previous
Screen
Button
Next
Screen
Button
Decrease
Button
Increase
Button
Ramp
Button
Start/Stop
Button
C-Flex
Button
C-Flex
Placement Area
for Optional Quick
Reference Label
FIGURE 2–3 DEVICE CONTROL PANEL
Loading...