Page 1
Quick guide
– GETTING STARTED
GETTING STARTED
(Charge the Micro Mic and pair to aids before use)
1. Turn on the Micro Mic: Push and hold the power buttonAon
the top of the Micro Mic until the status light
B
blinks green.
2. Connect your hearing aids to the Micro Mic: Push and hold
the program button/toggle button on your hearing aids until
you hear a melody.
Check the connection by blowing or tapping on the Micro Mic.
This sound should be audible in your hearing aids. If this is not
the case, see troubleshooting guide on the reverse page.
3. To exit the Micro Mic streaming program: Push the program
button/toggle button on your hearing aids. Your hearing aids will
return to the most recent hearing aid program indicated by one
or more beeps.
4. Turn off the Micro Mic: Push and hold the power button until the
status light turns red and then off.
B
STATUS LIGHT
• Will blink green every other second when
the Micro Mic is turned on and charged.
• Will blink orange every second when there
are less than 30 minutes of battery left.
C
VOLUME CONTROL
Use the volume buttons on the side of the
Micro Mic to adjust the volume. Press ‘+’ to
increase the volume and ‘-’ to decrease the
volume. The mute/volume light
E
will blink
each time the volume is
adjusted.
Mute
Mute/Volume light
USB charger
Volume control
Power button
Status light
A
D
E
C
F
B
F
CHARGING
• Insert the charger in the micro USB plug in
the bottom of the Micro Mic.
• Status light indications when charging:
Power/Charging Charging Fully charged
Powered Of f
Powered On
D
MUTE
To mute the Micro Mic press the mute button.
Now the mute/volume status light
E
will blink
orange every second. To unmute press the
mute button again, the mute/volume light will
stop blinking.
400669011-US-16.07-Rev.A.indd 1 05-07-2016 11:06:47
Page 2
For further instructions, please refer to the full
user guide provided with your Micro Mic
(Your dispenser will usually do this for you)
1. Push the power button on the Micro Mic and
hold until the status light turns green.
The Micro Mic is now turned on.
2. Find the pairing button placed below the pairing
icon
on the back side of the Micro Mic. If
you cannot find this icon, try rotating the clip.
3. Push the pairing button (use a pen or similiar).
The status light will now blink orange.
4. Open and close the battery doors on the
hearing aids. This must be done within 20
seconds of pushing the pairing button.
A successful pairing will be indicated by a melody
playing in the hearing aids and the status light will
stop blinking and be solid orange for 2 seconds
before resuming blinking.
Note: Remember that the hearing aids need
to be switched into the Micro Mic streaming
program to listen to the Micro Mic
TO PAIR YOUR HEARING AIDS AND MICRO MIC
400 6690 11-US -16.07-Re v.A
Manufacturer according
to FDA:
ReSound North America
8001 Bloomington Freeway
Bloomington, MN 55420
1-888-735-4327
resound.com
ReSound Government
Services
8001 Bloomington Freeway
Bloomington, MN 55420
1-8 00 -3 92-9932
resound.com/veterans
Manufacturer according
to Health Canada:
GN Hearing A/S
Lautrupbjerg 7
DK-2750 Ballerup
Distributor in Canada:
ReSound Canada
303 Super test Road
Toronto, Ontario
M3J 2M4
1-888-737-6863
resound.com
1. Check the status light. It should blink green
every 2 seconds. If it is not blinking, try pushing
and holding the power button until you see
a green light. If the status light turns red and
off the Micro Mic needs to be charged. If the
power status light blinks orange, this indicates
that the Micro Mic needs to be charged.
2. Check the Mute/Volume light, if it is blinking
orange this indicates that the Micro Mic is
muted. No sound is being sent to the hearing
aids. Push the mute button to unmute.
3. Check hearing aid battery status: Change
the battery in your hearing aids. Hearing aids
sometimes need new batteries to receive a
streamed signal, even if they are fine for normal
hearing aid use.
TROUBLESHOOTING GUIDE – NO CONNECTION
4. If Multiple Streaming Devices are
connected: If you have a TV streamer or more
than one Micro Mic
• Try pushing the hearing aid program button/
toggle button and holding until you hear a
melody
• Repeat this step (two long presses) (Micro
Mic can be placed in ‘channel’ 1, 2 or 3.)
5. Re-pair the Micro Mic to the hearing aids:
Directions on how to pair your hearing aids
and the Micro Mic can be found above.
The Micro Mic sends speech directly to your
hearing aids. It can be clipped to the desired
talker’s clothes, hung on a lanyard or be placed
on the table.
Speech understanding is easier when using the
Micro Mic because the microphone is closer to
the speaker’s mouth than your hearing aids are.
400669011-US-16.07-Rev.A.indd 2 05-07-2016 11:06:47
Loading...