Resolution RE311 User Manual

Wireless

Run

a light coat of

wipe it down

Remove

Align

Position

Antenna free and clear of sensor;

DON’T MOUNT

A.

Fasten with paste glue, as above.

D.

Drill hole and

C.

Route into trim gaps or

2.

½ inch or less

magnet gap

3.

O

pen

(Alarm) the

Sensor sends

Battery

Reed Switch

Antenna

Battery

Security
Solutions

RE311 Mighty Mouse™ DSC-Compatible Micro Door Sensor

Features

• Smallest Door/Window Sensor & Magnet in the Industry.

• Full-sized transmit range, AND…

• 4-6 year battery life on CR1632 battery.

• Invisible external antenna – gives great range and long life

• Low Battery indication.

Mounting

1.

High Bond
tape liners

4.

with finger

permanent paste
glue on the
underside of the

centering marks

not inside cover or under sensor.

Antenna Routing Options

B. Or let it lay on surface, nearly invisibly.

Enrolling in Panel

.

1. Pull out the red tab to power the sensor.

2. Put DSC panel in Wireless Enrollment Mode.

3. Open (alarm) the DWS that you want to enroll.

4. Confirm ESN, Enter Zone # and Zone Type on DSC Panel.

5. May also be enrolled via entering ESN.

Sensor

enrollment

signal

Internal Picture

contacts

Minus side up

ON METAL,
It will severely
reduce transmit
range and
magnetic gap

RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 1 of 4

along side of trim

13-May-12

www.ResolutionProducts.com

thread antenna down

RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 2 of 4

13-May-12

www.ResolutionProducts.com

Opening Cover

TO CLOSE

Insert

Tilt cover open.

Insert Screwdriver

Note small

Screwdriver

in slot

Hinge is in back away

from antenna

slide cover jaw into hinge.

Tilt closed.

Replacing Battery

in slot.

Twist.

retention post

Specifications

Magnet trip distance: 1 inch nominal
Supervisories: Hourly
Battery Life: 4+ years
Mounting fastener: 3M VHB (Very High Bond) Tape
Replacement Battery: CR1632
Temperature Range: 0F to 120F
Housing dimensions: 1.75 x 0.75 x 0.2 inches
Antenna dimension: 2 inches

Specifications subject to change without notice.

Notices

“GE”, “Honeywell”, “DSC” and “Napco” are trademarks owned by General Electric Company,
Honeywell International Inc., Tyco Safety Products Canada LTD, and NAPCO Security Systems,
Inc., respectively.

Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco
systems. However, no Resolution product is produced by, endorsed by, nor is officially associated
with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.

Warranty
Resolution Products, Inc. will replace products that are defective in their first year.

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:

This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could
void the user's authority to operate this equipment.

FCC ID: U5X-RE311

IC Notice

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may
cause undesired operation of the device.

Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:

1. Ce dispositif ne peut causer des interférences, et

2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.

IC: 8310A-RE311

RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 3 of 4

13-May-12

www.ResolutionProducts.com

RE311_DSC-Compat_Micro-DWS_Instructions.doc Page 4 of 4

13-May-12

www.ResolutionProducts.com