Resolution RE259, RE159, RE359 User Manual

360 Degree PIR Motion Sensor
I
360 PIR Motion Sensor alarms when motion is sensed.
It is a commercial battery-powered ceiling mount sensor with a 360 degree detection range.
Features
• 360° detection range with 62 distinct detection zones
• Range up to 40 feet in diameter
• Selectable pulse count 2 or 4
• 5 year warranty
Enroll by placing the panel into wireless enrollment mode
and tripping the sensor’s enrollment sequence. Interlogix® , DSC®, Qolsys® and Cryptix™ variants can be enrolled by pulling the battery tab or by tampering the unit. Honeywell ® and 2GIG™ variants can be enrolled by tripping the unit three times (tamper or motion) or by holding the tamper down and powering the unit up by pulling the battery tab. Honeywell and 2GIG sensors must be enrolled as a “Loop1” sensor. Alternatively, all variants of the motion sensor can be enrolled by entering its serial number into the panel.
A
T
S
L
L
N
I
G
E
U
D
I
Install by screwing two #8 screws into the ceiling, leaving 1/4
inch of thread exposed. Next, slide the back plate over the screws and rotate the back plate. Screw the third #8 screw through the wall tamper into the ceiling, ensuring that the wall tamper screw is attached to something solid. Tighten all screws until snug. Then, insert the square nut into the square slit of the cover and start threading the #4 screw into the side of the cover. Close the cover and conduct a walk test. After walk testing, take the unit out of walk test mode and
close the cover again. Finally, nish threading the #4 screw
until it is snug.
Mounting Tips
• Avoid direct sunlight
• Avoid facing directly to AC or heating vents
• Avoid vapor or high humidity
• Avoid curtains, screens, etc. from blocking detection
• Do not install outdoors
Use your panel’s installation guide to verify proper system setup.
Sensor functions
Alarm LED can be switched either “ON” or “OFF”. Pulse Count can be switched to either “2” or “4” mode
depending on the environmental conditions of the installation.
Pulse Count
• Select “2” for normal applications.
• Select “4” for use in areas where there may be movement by small animals or other objects, such as fax machines or curtains.
Walk Test Switch LED lights up when the unit has
detected motion. An alarm signal is outputted whenever detection occurs.
Normal Operation (Battery Saving Mode)
LED lights up when the unit has detected if “LED ON” is selected. Once alarm is outputted, it does not output alarm again for 2 minutes. It goes back after 2 minutes and outputs alarm again when receiving detection signal.
Detection Range
Troubleshooting
Problem Probable Cause Remedy
Alarm is not activated although someone is walking in detection area
Alarm is activated with nobody in the area
LED does not light up at the time of the walk test
LED does not light up in normal operation
Detection area is improper, battery is dead, Walk Test switch is OFF and 2 minute delay is active
Moving object within detection area, temperature of object within area is changing rapidly
Walk test switch is OFF, battery is dead
LED switch is OFF, battery is dead
Conduct a walk test, change the battery
Remove the object from the detection area, remove the heat sources from the detection area or relocate the detector
Turn the walk test switch ON, change the battery
Turn LED switch ON, change battery
Pro Tips
Save battery life by taking unit out of walk test mode after
completing walk test. There is no 2 minute delay when in walk test mode. Leaving in walk test mode will severely decrease battery unit life.
Light changes will cause the sensor to trip. Ensure that the
detector is not placed near windows.
Sudden temperature changes will cause the sensor to trip.
Ensure the motion detector is not placed near heating and cooling vents.
High humidity environments can cause condensation of
the detection lens. Ensure the motion detector is not installed in these kinds of environments.
Protective lm should be removed from the lens after
installation.
Sensor Specications: The table below displays the
functional frequencies of each compatible sensor.
Part Number Frequency Compatible
RE159 319.5 Interlogix/Qolsys
RE259 345 Honeywell
RE259T 345 2GIG
RE359 433 DSC
RE659 433 Cryptix
Specications
Physical
Housing Dimensions Weight with Battery Mounting Fasteners
Environmental
Operating Temperature Maximum Humidity
Sensor Specications
Frequencies Replacement Battery Nominal Battery Life
Battery Voltage Current Draw Detection Length
Detectable Speed Transmitted Indications
Certication
RE159, RE259, RE259T, RE359, RE659
4.72 x 1.57 inches (40 x 120 mm)
4.2oz (120g) (3) #8 screws, (1) square nut, (1) #4 screw (All provided)
32°F to 120°F (0°C to 49°C) 85% non-condensing relative humidity
433.92 MHz, 319.5 MHz, 345 MHz One Panasonic CR123A Lithium Battery 3 years (assuming 720 trips/day), 7 years (assuming 240 trips/ day)
3.3 VDC (Nominal), 2.4 VDC (Low) 21 mA (Maximum), 4.7 uA (Standby), 30 mA (Max in walk test) Default: 16.5 feet (5m), Optional: 6.5 feet (2m)
1 to 5 feet per second (0.3 to 1.5 meters per second)Motion, Tamper (Cover/Wall), Low Battery, Supervision
UL639, ULC-S306-03, ETL, FCC, IC
Specications subject to change without notice
WARRANTY
Resolution Products, Inc. will replace all non-portable products
that are defective in their rst ve (5) years, and all portable products that are defective in their rst two (2) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC: 8310A-RE159, 8310A-RE259, 8310A-RE359
47-0047-00 • RevA • 2018-01-18
Tech Support Line (877) 260-5578
www.ResolutionProducts.com
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. (2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Resolution
Products, Inc. could void the user’s authority to operate this equipment.
FCC ID: U5X-RE159, U5X-RE259, U5X-RE359
TRADEMARKS
INTERLOGIX, HONEYWELL, 2GIG, QOLSYS, AND DSC ARE TRADEMARKS OWNED BY UNITED TECHNOLOGIES ELECTRONIC CONTROLS INC., HONEYWELL INTERNATIONAL INC., TYCO SAFETY PRODUCTS CANADA LTD, QOLSYS INC. AND NORTEK SECURITY & CONTROL LLC, RESPECTIVELY. RESOLUTION PRODUCTS, INC. PRODUCTS WILL FUNCTION WITH ONE OF EITHER INTERLOGIX (FORMERLY GE), HONEYWELL, DSC, OR 2GIG SYSTEMS. HOWEVER, NO RESOLUTION PRODUCT IS PRODUCED BY, ENDORSED BY, NOR IS OFFICIALLY ASSOCIATED WITH INTERLOGIX (FORMERLY GE), HONEYWELL, DSC OR 2GIG. RESOLUTION RECOMMENDS VERIFYING PROPER ENROLLMENT AND OPERATION, PER CONTROL PANEL INSTALLATION INSTRUCTIONS, AT INSTALLATION.
Loading...