Resolution RE252T2GIG User Manual

RE252T_2GIG-Compat_PIN-Pad Page 1 of 3 16-May-14

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

RE252T 2GIG-Compatible PINpad™

Features

• Secure, 4-digit Code to disarm

• 1-button arming

• Red/Green LED arming feedback

• Small, yet comfortable keypad

• Mounts on wall via VHB® tape, or screws

• Secure for carrying in purse or mounting on car visor

• 4-6 year battery life on CR2032 battery.

Key Instructions

• Program as a RF Key Fob, NOT a RF Keypad

• PIN Code programming

Default access code is “1234”.
To change access code: Do these steps within 4 seconds

1. Enter current 4-digit access code.

2. Press and hold the “1” and “3” keys simultaneously.
(after 3 seconds, Red LED will be lit)

3. Enter new 4-digit access code.

(the Green LED will be lit)

Note new access code . BAD GUY CANNOT RESET CODE.
So it must be recorded and remembered!

2GIG Go! Panel:

Question

Answer

Q3:

Select fob # (1-8)

[1] keyfob one

Select fob 1 used (0

-1)

[1] used

Select fob 1 equipment code

[0000] other

Enter fob 1 other equipment code (0

-

9999) 252 (RE252)

Enter fob 1 serial number

Go! Panel: Shi

ft+Learn

PINpad Keypad: STAY

Select fob 1 equipment age

[0] new

Select fob 1 emergency key (0

-4)

[2] audible alarm

Construct RF Keypad Voice Descriptor

keypad one

Operation

PINpad

Button

Panel Action LED

Stay ARM STAY

flashes double red

Away ARM AWAY

flashes double red twice

PIN Code

DISARM flash

es double green

Stay + Away

PANIC ALARM

flashes red 8 times

RE252T_2GIG-Compat_PIN-Pad Page 2 of 3 16-May-14

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

Pictures

Battery Replacement

CR2032 Battery

+ Terminal up

Insert Screwdriver

here

to open

Stay + Away

Sends Panic

Loop 2+3

Entering

Code

Sends Disarm

Loop 2

Away

Loop 3

Stay

Loop 4

TO CHANGE PIN CODE:

Current 4-digit access code, and then…

1 + 3  Red LED,and then…

Enter New Code

Red/Green

Status LED
Shows command sent

RE252T_2GIG-Compat_PIN-Pad Page 3 of 3 16-May-14

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

Specifications

Replaces 2GIG-PAD1, but smaller and lower cost
Not supervised.
Replacement Battery: CR2032 Lithium / Manganese Dioxide
Temperature Range: 0F to 120F
Housing dimensions: 2x2.25x0.33 inches
1-way RF: Does not receive panel status

Specifications subject to change without notice.

Notices

“GE”, “Honeywell”, “DSC”, “2GIG” and “Napco” are trademarks owned by General Electric
Company, Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies
Inc., and NAPCO Security Systems, Inc., respectively.

Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or
Napco systems. However, no Resolution product is produced by, endorsed by, nor is officially
associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper
enrollment and operation, per control panel installation instructions, at installation.

Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.

FCC Notice

This device complies with Part 15 of the FCC rules. Operat ion is subject to the
following two conditions:

This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could
void the user's authority to operate this equipment.

FCC ID: U5X-RE252

IC Notice

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux ap pareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC: 8310A-RE252