Resolution RE213 User Manual

Situation

Sounder

LED Wireless Signal

to Panel

Recovery

Actual CO

Temporal 3

RED

Wireless CO

When CO is no longer

sensor for 4 minutes.

Press & hold Test

2 Temporal 4

RED, Green,

Sensor Alarm

Sensor:

Release button.

Removing Sensor

1 Beep

once every minute

Yellow

Tamper/Trouble

to panel.

Restore by remounting.

Low Battery

1 beep (loud)

Yellow

Low battery

Hourly Check

Supervisories,

every hour

Maintenance

1 Chirp every

Yellow flash

Supervisories

Replace Unit

Low Sensitivity

1 Chirp every

Yellow flash

Supervisories

Re

place Unit

End Of Life

1 Chirp every

Yellow flashes

Supervisories

Replace Unit

Wireless

Solutions

Available for…

Honeywell

2GIG

GE

DSC

Battery

CO Sensing

Tamper

Mounting

LED's

Battery

Security

RE213 Honeywell-Compatible Carbon Monoxide Alarm

Features

• Senses and alarms to Carbon Monoxide per UL2034

• Sleek design

• Cover tamper.

• Strong, reliable RF signal.

• 3-5 year battery life on 3 Panasonic LR6-AA batteries.

• Low Battery indication.

Key Instructions

1. Attach the mounting plate
Locate on ceiling, or wall in or near sleeping areas.
Some local codes have specifications on CO detectors.
Mounting plate removes counter-clockwise

2. Insert batteries making sure of polarity. Close battery door.

3. Enroll sensor in panel:
a) Enter Zone Programming Mode (e.g. *56)
b) Zone Type = 14
c) Input type = Supervised RF Transmitter.
d) When asked for a serial number, press Tamper button
e) Select Loop 1 for CO

4. Testing:

a) Place panel in Sensor Test mode.
b) Press & hold TEST button until you the sounder beep.
c) Panel will indicate the sensor is open, and alarm will sound.

NOTE: Using CO-in-a-Can will cause an actual CO alarm.

Operation

Specifications

CO Sensitivity: (UL2034)
70ppm 60-120 minutes
150ppm 10-50 minutes
400ppm 4-15 minutes

(EN50291)
50ppm 60-90 minutes
100ppm 10-40 minutes
150ppm 3 minutes or less

CO Sensing Technology: Electrochemical

Heat Alarm Point: 135 – 149 F (UL 521)

Alarm Sound: Temporal Three
Replacement Battery: 3 Panasonic LR6-AA
Temperature Range: 40 to 100 F (Long Term)
Humidity: 0 – 95% Relative Humidity
Housing dimensions: 4.9 inch diameter, 1.4 inch high

Specifications subject to change without notice.

Tabs

Button

from Mount

Needed

RE213_Honeywell-Compat_CO_Instructions Page 1 of 4 15-May-14

(Loud) every 8
seconds

Beeps
(Loud)

(Loud)

every 60 seconds

minute

minute

minute

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

(pulsing)

& Yellow
(pulsing)

(steady)

(pulsing)

every minute

twice a
minute

4 times a
minute

Alarm Signal
sent to panel

signal to panel

signal to be sent

Not Sent

Not Sent

Not Sent

present.
TEST button will silence

Panel: Clear alarm
condition.

Pictures

Element

RED GREEN YELLOW

TEST Button

Bucket

Door

Release

Button

RE213_Honeywell-Compat_CO_Instructions Page 2 of 4 15-May-14

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

Opening Cover

1. Press Down

3. Notice

2. Slide

Battery

Door

Down

On

Release

Button

Battery

Polarity

Notices

Verify proper enrollment and operation, per control panel installation instructions, at installation.

CARBON MONOXIDE ALARM M330 USER’S MANUAL, which is included in device box, is an integral part
of the operating information of the RE213 device.

Approved as a self-contained carbon monoxide alarm per UL2034. This represents the ability of each
individual sensor to sound locally upon sensed carbon monoxide conditions.

“GE”, “Interlogix”, “Honeywell”, “2GIG”, “DSC”, “Napco” are trademarks owned by General Electric
Company, UTC Fire & Security Americas Corporation, Inc., Honeywell International Inc., 2GIG
Technologies Inc., Tyco Safety Products Canada LTD, Napco Security Systems respectively.

Resolution Products, Inc. products will function with one of either GE/Interlogix, Honeywell and
2GIG, DSC or Napco. However, no Resolution product is produced by, endorsed by, nor is officially
associated with any of these other manufacturers. Resolution recommends verifying proper
enrollment and operation, per control panel installation instructions, at installation.

Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:

(1)This device may not cause harmful interference.
(2)This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.

FCC ID: U5X-RE213

IC Notice

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC: 8310A-RE213

RE213_Honeywell-Compat_CO_Instructions Page 3 of 4 15-May-14

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

RE213_Honeywell-Compat_CO_Instructions Page 4 of 4 15-May-14

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com