Resolution RE212T Instructions Manual

RE212T_2GIG-Compat_Smoke_Instructions Page 1 of 4 22-Feb-16

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

RE212T 2GIG-Compatible Smoke & Heat Alarm

Features

• UL217 Self-Contained Fire Alarm Device

• Senses and alarms to Smoke per UL217

• Heat alarm at 144 degrees.

• Sleek design.

• Cover tamper.

• Strong, reliable RF signal.

• 3-5 year battery life on Panasonic CR123A battery.

• Low Battery indication.

Key Instructions

1. Attach the mounting plate
Locate on ceiling, as close to center as possible, away from corners.
Some local codes may allow wall mounting.
Mounting plate removes counter-clockwise

2. Insert battery with MINUS towards the RED lever. Close battery door.

3. Enroll sensor in panel:

Q1:

Select RF sensor # (01-48)

Zone number of your choice

Select RF sensor type [09] 24-Hour Fire, or [16] 24-Hour Fire w/

Verification

(See Control Panel Installation

Manual)

Select RF sensor equip type [1] Contact

Select RF sensor equip code [0872] SMKE1-345 smoke detector

Select RF sensor serial number Press Shift, Press Learn

Press and hold the TEST Button for 5 seconds

Select RF sensor Age [1] New

Select RF sensor Loop number [1] Motion

4. Testing:

a) Place panel in Sensor Test mode
b) Press & hold TEST button until you hear the sounder beep.
c) Panel will go into alarm.

NOTE: Using Smoke-in-a-Can will cause an actual Fire Alarm.

Available for…

GE

Honeywell

2GIG

DSC

Answer

Question

RE212T_2GIG-Compat_Smoke_Instructions Page 2 of 4 22-Feb-16

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

Operation

Situation

Sounder

LED Wireless Signal

to Panel

Recovery

Actual smoke

Temporal 3

(Loud)

RED

(pulsing)

Wireless Fire

Alarm Signal sent
to panel

Silence an actual

alarm with the TEST
button. Sensor will
return to alarm if
smoke is still

present.

Pre

ss & hold

Test Button

Temporal 3

(Loud)

RED

(pulsing)

Sensor Alarm

signal to panel

Sensor: Release

button.
Panel: Restores after

alarm is cancled

Removing

Sensor from

Mount

Temporal 3

(Loud)

Yellow

(steady)

Tamper/Trouble

signal to be sent

to panel.

Rest

ore by

remounting.

Low Battery

Yellow

(pulsing)

Hourly Check

Supervisories,

every hour

Maintenance

Needed

Temporal 3

(Loud)

Yellow

(Pulsing)

Supervisories Not

Sent

Replace Unit

Specifications
Approval: UL217 Self-Contained Fire Alarm Device

Smoke Sensitivity: 1.31 – 2.28 %/ft (UL 217)

0.11 – 0.165 dB/m (EN54-7)
Smoke Sensing Technology: Photoelectric

Heat Alarm Point: 135 – 149 F (UL 521)

Alarm Sound: Temporal Three
Replacement Battery: Panasonic CR123A
Temperature Range: 32 to 120 F (Long Term)
Humidity: 10 – 85% Relative Humidity
Housing dimensions: 4.7 inch diameter, 2.1 inch high

Design & Manufacture: Resolution Products, Inc.

Specifications subject to change without notice.

RE212T_2GIG-Compat_Smoke_Instructions Page 3 of 4 22-Feb-16

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

Pictures

Battery

+

Smoke Sensing

Element

Mounting

Tabs

Tamper

Heat Sensor

TEST Button

LED

RE212T_2GIG-Compat_Smoke_Instructions Page 4 of 4 22-Feb-16

24-Hour Tech Support Line: [phone]

www.ResolutionProducts.com

Notices

Verify proper enrollment and operation, per control panel installation instructions, at installation.

PHOTOELECTRIC SMOKE & HEAT USER'S MANUAL, which is included in device box, is an integral pa rt
of the operating information of the RE212T device. However, this is NOT a heat device.

Loop 2 Maintenance is only supported on c ommercial control panels. See Honeywell Installation Manual.

Approved as a self-contained fire alarm device per UL217. This represents the ability of each
individual sensor to sound locally upon sensed fire conditions.

“GE”, “Interlogix”, “Honeywell”, “2GIG”, “DSC”, “Napco” are trademarks owned by General Electric
Company, UTC Fire & Security Americas Corporation, Inc., Honeywell International Inc., 2GIG
Technologies Inc., Tyco Safety Products Canada LTD, Napco Security Systems respectively.

Resolution Products, Inc. products will function with one of either GE/Interlogix, Honeywell and
2GIG, DSC or Napco. However, no Resolution product is produced by, endorsed by, nor is officially
associated with any of these other manufacturers. Resolution recommends verifying proper
enrollment and operation, per control panel installation instructions, at installation.

Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.

FCC Notice

This device complies with Part 15 of the FCC rules. Operat ion is subject to the following two
conditions:

(1)This device may not cause harmful interference.
(2)This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.

FCC ID: U5X-RE212

IC Notice

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux ap pareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC: 8310A-RE212