Resolution RE202 User Manual

Wall mount

Battery

Magnet

Reed

Wireless
Security
Solutions

RE202 Honeywell-Compatible Pencil Door / Window

Features

• Senses opening or separation. Narrow mounting locations.

• ½ width of competitive products. Great for casements!

• Magnet and Internal reed switch operation.

• Magnet can mount beside or over sensor housing.

• Strong, reliable RF signal.

• 8-10 year battery life on 2-AAA batteries.

Key Instructions

• Battery “+” faces towards white “+” on circuit board.

• Install batteries: rear batt – tail in first, front battery – nose in first.

• Board goes in and out of housing without batteries (not with).

• Reed switch is at the top of the housing, near the push button hole.

• Reed switch = Loop 2

• (Inserting battery will send a Loop 4 Tamper, but Sensor does not

actually have a tamper)

• Enrolling:

 Place Panel in RF Learning mode.
 Input Type = RF
 Lynx *56 “E I” mode:

To enroll any particular loop: cause the loop to fault…
restore… (panel should beep to indicate ID capture)…
fault… restore… [panel will confirm enrollment].

 Vista *56 “10 INPUT S/N: L” mode:

Transmit two open/close sequences (using magnet).
Press * (to check for duplicate serial/loop number).
Press * (to continue to confirmation screen).
Press * if you wish to skip confirmation; or “Yes” and
activate the loop to confirm.

Operation

• Magnetic reed switch:

• Supervisories, every hour.

Specifications

Internal Picture

Alarm, when…

… magnet is pulled away from reed switch.

Magnet trip distance: 0.75 inch nominal
Mounting hardware: # 4 or #6 screws
Replacement Battery: 2 AAA Alkaline
Temperature Range: 0F to 120F
Housing dimensions: 4 x 0.6 x 0.9 inches.

Specifications subject to change without notice.

position

Switch

ID Barcode

Positive

plate

RE202_Honeywell-Compat_Pencil_DWS_Instructions.doc Page 1 of 3 28-Jul-11

www.ResolutionProducts.com

RE202_Honeywell-Compat_Pencil_DWS_Instructions.doc Page 2 of 3 28-Jul-11

www.ResolutionProducts.com

Notices

“GE”, “Honeywell”, and “DSC” are trademarks owned by General Electric Company, Honeywell
International Inc., and Tyco Safety Products Canada LTD, respectively.

Resolution Products, Inc. products will function with one of either GE, DSC or Honeywell
systems. However, no Resolution product is produced by, endorsed by, nor is officially
associated with GE, Honeywell or DSC. Resolution recommends verifying proper enrollment
and operation, per control panel installation instructions, at installation.

Warranty
Resolution Products, Inc. will replace products that are defective in their first year.

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:

This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could
void the user's authority to operate this equipment.

FCC ID: U5X-RE202

IC Notice

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may
cause undesired operation of the device.

Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence.
Son fonctionnement est soumis aux deux conditions suivantes:

1. Ce dispositif ne peut causer des interférences, et

2. Ce dispositif doit accepter toute interférence, y compris les interférences
qui peuvent causer un mauvais fonctionnement du dispositif.

IC: 8310A-RE202

RE202_Honeywell-Compat_Pencil_DWS_Instructions.doc Page 3 of 3 28-Jul-11

www.ResolutionProducts.com