Resolution RE115 User Manual
A
I
CARBON
MONOXIDE
ALARM
ALARM
FAULT
POWER
Red
Light
Amber
Light
Green
Light
Test
Button
T
S
L
L
N
I
G
U
D
I
CO Alarm
CO Alarm is a life-safety device that
alarms when it detects carbon
monoxide.
Features
• UL2034 and CSA 6.19-01 listings
• Detects carbon monoxide
• 5 year warranty
Key Instructions
1. Review sections 1 and 2 for
information regarding the CO alarm.
2. Determine where to place the CO
alarms per Section 3.
3. Install per Section 4.
Cryptix Enrolment:
4. Enroll the CO alarm into the panel:
• Place panel in enrollment mode
• Press and hold TEST button until you
hear the sounder beep
• The panel will learn the CO alarm
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will indicate a CO Test by
sounding temporal 4 siren one time
Interlogix Compatible Enrollment
• Place panel in enrollment mode
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will learn the CO alarm-
recommended group 34
• Test that the CO alarm is enrolled in
the panel:
• Put panel into test mode
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will indicate a CO sensor has
tripped
This manual should be read prior to use and retained for further information.
Use the Helix installation guide to verify proper system setup.
Attention
E
Honeywell Compatible Enrollment
• Place panel in enrollment mode
• Zone type= Carbon Monoxide
• Input type= Supervised RF
Transmitter
• When asked for a serial number:
trip tamper twice
• To tamper, turn base counter-
clockwise. Wait for two seconds
and restore the base. Wait for
three seconds and repeat steps.
• Select Loop 1 for CO
• Put panel into test mode
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will indicate a CO sensor
has tripped
2GIG Compatible Enrollment
• Place panel in enrollment mode
• Q1: Select RF sensor number
(01-48) zone number of your
choice
• Select RF sensor type [14] 24
hour carbon monoxide (see
control panel installation manual)
• Select RF sensor equip type [1]
• Select RF sensor equip code
[0860] CO1-345 CO detector
• Select RF sensor serial number
and press shift, press learn trip
sensor
• Select RF sensor age [1] New
• Select RF sensor Loop number
[1]
• Put panel into test mode
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will indicate a CO sensor
has tripped
DSC Compatible Enrollment
• Place panel in enrollment mode
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will learn the CO alarm
• Recommended group is 81
• Test that the CO alarm is
enrolled in the panel
• Put panel into test mode
• Press and hold TEST button until
sounder is done sounding beeps
• Panel will indicate a CO sensor
has tripped
5. Test that the CO alarm is enrolled
in the panel.
6. Review Section 5 for CO alarm
testing and maintenance.
• Test the functionality of the CO
alarm weekly.
7. Review Sections 6 and 7 for
information regarding what to
do when the alarm sounds and
information regarding how to
protect your family.
8. Review how to have your alarm
serviced per Section 8.
9. For troubleshooting information,
refer to Section 9.
1. Read This First
Congratulations on becoming the owner
of a carbon monoxide alarm. This will
help protect you and your household
from the dangerous effects of carbon
monoxide - the silent killer.
• Wait 15 seconds after connecting
the power before button testing. We
recommend you:
• Install a CO alarm in every room that
contains a fuel burning appliance,
particularly rooms where people spend
a lot of time, such as bedrooms,
kitchens, etc.
• In rooms with an appliance, install
(preferably) on the ceiling (300mm
from walls) and between 1.5m to 3m
horizontally away from the appliance.
In rooms remote from the appliance,
install at ‘head height’, where the light
indicators can be seen.
2
• Test the alarm weekly by pressing the
test/hush button. The horn will sound at
a diminished sound output level initially
and then quickly reach maximum sound
output level.
• Replace alarm after approximately 10
years operation (see ‘replace by’ date
on label).
• Do not install alarm until all building work
is completed to avoid contamination.
• Individuals with medical problems may
consider warning devices which provide
audible and visual signals for carbon
monoxide concentrations under 30ppm.
2. Carbon Monoxide - The
Silent Killer
2.1 What is carbon monoxide?
Many people are killed each year, and
many more suffer ill health from carbon
monoxide (CO) poisoning. CO is an
invisible, odorless, tasteless and extremely
toxic gas. It is produced by appliances and
vehicles burning fuels, such as coal, oil,
natural/bottled gas, paraffin, wood, petrol,
diesel, charcoal, etc. CO is absorbed by
red blood cells in the lungs in preference
to oxygen - this results in rapid damage
to the heart and brain from oxygen
starvation.
High levels of CO in a house can be
caused by:
• Incorrectly or poorly installed fuel-burning
appliances
• Blocked or cracked chimneys/flues
• Blocked vents or draft-proofing
which makes areas with fuel-burning
appliances or fireplaces airtight
• Engines of cars, lawnmowers, etc. left
running in confined spaces
• Portable paraffin or gas heaters in badly
ventilated rooms
2.2 What happens when your CO Alarm
detects Carbon Monoxide?
When the Alarm detects potentially
dangerous levels of CO, it flashes the red
alarm light immediately and then sounds
a loud alarm if the CO persists. Table
B shows how the CO Alarm reacts to
different levels of CO gas and exposure
time. At higher levels of CO the alarm
turns on sooner. The rate of flashing of
the red light indicates the level of CO.
If your CO Alarm sounds, follow the
instructions in Section 6. NEVER IGNORE
THE ALARM!
2.3 Symptoms of CO Poisoning
CO in
PPM
35 The maximum allowable
concentration exposure
in any 8 hour period
according to OSHA
150 Slight headache after 1.5
hours
200 Slight headache, fatigue,
dizziness, nausea after 2-3
hours
400 Frontal headaches
within 1-2 hours, life
threatening after 3 hours,
also maximum parts per
million in ue gas (on an
air free basis) according
to US Environmental
Protection Agency.
800 Dizziness, nausea and
convulsions within 45
minutes. Unconsciousness
within 2 hours. Death within
2-3 hours.
1600 Headache, dizziness, and
nausea within 20 minutes.
Death within 1 hour.
3200 Headache, dizziness and
nausea within 5-10 minutes.
Death within 25-30 minutes.
6400 Headache, dizziness and
nausea within 1-2 minutes.
Death within 10-15 minutes.
12800 Death within 1-3 minutes
The following symptoms may be related
to Carbon Monoxide Poisoning and
should be discussed with all members of
the household:
Mild exposure: Headaches, running
nose, sore eyes, often described as “flu
like symptoms”
Medium Exposure: Dizziness,
drowsiness, vomiting
Extreme Exposure: Unconsciousness,
brain damage, death
Many cases of reported carbon
monoxide poisoning indicate that while
victims are aware they are not well, they
become so disoriented they are unable
to save themselves by either exiting the
building or calling for assistance.
3
Symptoms
*OSHA Occupational Safety and
Health Association
Alarm Indicators
Condition Indicator
Pre Alarm Red LED flash only
CO Alarm Red LED flash + sounder
Faults Yellow LED flash + beeps
Table B: CO Alarm Response
CO
Red Light Horn/
Gas
Level
0 - 30
ppm
>50
ppm
>110
ppm
>250
ppm
Off (unless
it has
alarmed
previously)
1 flash
every 3
seconds
2 flashes
every 3
seconds
3 flashes
every 3
seconds
Sounder
Off
On within
60-240
minutes
(typically 90
minutes)
On within
10-50
minutes
(typically 30
minutes)
On within
4-15 minutes
(typically 9
minutes)
Pre-Alarm (before horn sounds): When
the Alarm detects over 50 ppm CO, the
red light flashes in accordance with Table
B. This helps locate CO leaks as the unit
gives an indication straight away.(Without
this feature the CO level would need to
be at 50 ppm CO for typically 72 minutes
for an alarm sound to be given). Note: the
pre-alarm signal may be triggered by CO
coming for example, from cooking with
gas, from car engines, or from nearby
barbecues. This is usually not a concern,
unless the pre-alarm signal persists until
the alarm sounds and the CO source is
unknown.
NOTE: The CO Alarm may sound if
cigarette smoke is blown into it, or
aerosols are released nearby.
CO ALARM MEMORY
The CO Alarm memory is an important
feature of the CO Alarm where even if
the house is unoccupied during an alarm
condition, it warns the homeowner that
the unit has previously detected CO gas
and been in alarm. The memory feature
has two operation modes:
- memory indication for 24 hour period
after alarm
- memory recall on demand
24 hour memory indicators: After
alarm, the RED light will flash at different
rates every 50 seconds depending on
the level of CO detected - see the CO
Response Table.
Memory recall on demand: To review
the memory status after initial 24 hours,
press and hold the test button. The red
4
Loading...