Resolution RE112 User Manual

Wireless

DSC

Security
Solutions

RE112 GE-Compatible Smoke Sensor

Features

• UL217 Self-Contained Fire Alarm Device

• Senses Smoke per UL217

• Sleek design

• Cover tamper.

• Strong, reliable RF signal.

• 3-5 year battery life on Panasonic CR123A battery.

• Low Battery indication.

Key Instructions

1. Attach the mounting plate
Locate on ceiling, as close to center as possible, away from corners.
Some local codes may allow wall mounting.
Mounting plate removes counter-clockwise

2. Insert battery with MINUS towards the RED lever. Close battery door.

3. Enroll sensor in panel:
a) Place panel in Learn Sensor mode
b) Press & release the black tamper switch

Sounder will continue beeping 3 times, until sensor is mounted.

4. Testing:
a) Place panel in Sensor Test mode
b) Press & hold TEST button until you hear the sounder beep.
c) Panel will indicate the sensor is open, but Fire Alarm will not sound.
NOTE: Using Smoke-in-a-Can will cause an actual Fire Alarm.

Specifications

Approval: UL217 Self-Contained Fire Alarm Device
Smoke Sensitivity: 1.31 – 2.28 %/ft (UL 217)

Smoke Sensing Technology: Photoelectric

Heat Alarm Point: 135 – 149 F (UL 521)

Alarm Sound: Temporal Three
Replacement Battery: Panasonic CR123A
Temperature Range: 32 to 120 F (Long Term)
Humidity: 10 – 85% Relative Humidity
Housing dimensions: 4.7 inch diameter, 2.1 inch high

Desing & Manufacture: Resolution Products, Inc.

Specifications subject to change without notice.

Pictures

Smoke Sensing

Element

0.11 – 0.165 dB/m (EN54-7)

Tamper

Mounting

Tabs

Operation

Situation Sounder LED Wireless Signal

Actual smoke Temporal 3

Press & hold
Test Button

Removing
Sensor from
Mount
Low Battery Yellow

Hourly Check Supervisories,

RE112_GE-Compat_Smoke_Instructions.doc Page 1 of 3 30-Jul-13

(Loud)

Temporal 3
(Loud)

Temporal 3
(Loud)

RED
(pulsing)

RED
(pulsing)

Orange
(steady)

(pulsing)

www.ResolutionProducts.com

to Panel

Wireless Fire
Alarm Signal sent
to panel

Sensor Open
signal to panel

Tamper/Trouble
signal to be sent
to panel.

every hour

Recovery

Silence an actual
alarm with the TEST
button. Sensor will
return to alarm if
smoke is still
present.
Sensor: Release
button.
Panel: Wait one
hour, or unmount &
mount sensor.
Restore by
remounting.

TEST Button

LED

RE112_GE-Compat_Smoke_Instructions.doc Page 2 of 3 30-Jul-13

www.ResolutionProducts.com

Battery

+

Notices

Verify proper enrollment and operation, per control panel installation instructions, at installation.

PHOTOELECTRIC SMOKE & HEAT USER'S MANUAL, which is included in device box, is an integral part
of the operating information of the RE112 device. However, this is NOT a heat device.

Approved as a self-contained fire alarm device per UL217. This represents the ability of each
individual sensor to sound locally upon sensed fire conditions.

“GE”, “Interlogix”, “Honeywell”, “2GIG”, “DSC”, “Napco” are trademarks owned by General Electric
Company, UTC Fire & Security Americas Corporation, Inc., Honeywell International Inc., 2GIG
Technologies Inc., Tyco Safety Products Canada LTD, Napco Security Systems respectively.

Resolution Products, Inc. products will function with one of either GE/Interlogix, Honeywell and
2GIG, DSC or Napco. However, no Resolution product is produced by, endorsed by, nor is officially
associated with any of these other manufacturers. Resolution recommends verifying proper
enrollment and operation, per control panel installation instructions, at installation.

Warranty
Resolution Products, Inc. will replace products that are defective in their first 5 years.

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:

This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.

FCC ID: U5X-RE112

IC Notice

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause
undesired operation of the device.

Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:

1. Ce dispositif ne peut causer des interférences, et

2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.

IC: 8310A-RE112

RE112_GE-Compat_Smoke_Instructions.doc Page 3 of 3 30-Jul-13

www.ResolutionProducts.com