Resolution RE111 User Manual
Wireless
Run
a light coat of
wipe it down
Remove
Align
Position
Antenna free and clear of sensor;
DON’T MOUNT
magnetic gap
A.
Fasten with paste glue, as above.
D.
Drill hole and
C.
Route into trim gaps or
1.
2.
½ inch or less
magnet gap
3.
4.
Pull Tab to send
Open/Close 5 times
Sensor sends
Battery
Reed Switch
Antenna
Battery
Security
Solutions
RE111 Mighty Mouse™ GE-Compatible Micro Door Sensor
Features
• Smallest Door/Window Sensor & Magnet in the Industry.
• Full-sized transmit range, AND…
• 4-6 year battery life on CR1632 battery.
• Invisible external antenna – gives great range and long life
• Low Battery indication.
Mounting
High Bond
tape liners
with finger
permanent paste
glue on the
underside of the
centering marks
not inside cover or under sensor.
Antenna Routing Options
B. Or let it lay on surface, nearly invisibly.
Enrolling in Panel
.
1. Put GE panel in enrollment mode.
2. Pull out the red tab to trip the sensor. This powers the sensor and it sends
a tamper enrollment signal.
3. The tamper enrollment signal can be re-sent by touching a magnet to the
sensor 5 times within 5 seconds.
in 5 seconds
Tamper-Enroll signal
Internal Picture
Minus side up
tamper
enrollment
signal
contacts
ON METAL,
It will severely
reduce transmit
range and
RE111_GE-Compat_Micro-DWS_Instructions.docPage 1 of 4 9-Apr-12
along side of trim
www.ResolutionProducts.com
thread antenna down
RE111_GE-Compat_Micro-DWS_Instructions.docPage 2 of 4 9-Apr-12
www.ResolutionProducts.com
Opening Cover
TO CLOSE
Insert
Tilt cover open.
Insert Screwdriver
Note small
Screwdriver
in slot
Hinge is in back away
from antenna
slide cover jaw into hinge.
Tilt closed.
Replacing Battery
in slot.
Twist.
retention post
Specifications
Magnet trip distance: 1 inch nominal
Supervisories: Hourly
Battery Life: 4+ years
Mounting fastener: 3M VHB (Very High Bond) Tape
Replacement Battery: CR1632
Temperature Range: 0F to 120F
Housing dimensions: 1.75 x 0.75 x 0.2 inches
Antenna dimension: 2 inches
Specifications subject to change without notice.
Notices
“GE”, “Honeywell”, “DSC” and “Napco” are trademarks owned by General Electric Company,
Honeywell International Inc., Tyco Safety Products Canada LTD, and NAPCO Security Systems,
Inc., respectively.
Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco
systems. However, no Resolution product is produced by, endorsed by, nor is officially associated
with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first year.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could
void the user's authority to operate this equipment.
FCC ID: U5X-RE111
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences, et
2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
IC: 8310A-RE111
RE111_GE-Compat_Micro-DWS_Instructions.docPage 3 of 4 9-Apr-12
www.ResolutionProducts.com
RE111_GE-Compat_Micro-DWS_Instructions.docPage 4 of 4 9-Apr-12
www.ResolutionProducts.com
Loading...