Resolution Opus 21 XS extra sources Owner's Manual

Opus 21

XS extra sources

Owner's Manual

r e s o l u t i o n

From all of us at Resolution Audio, thank you for choosing the Opus 21 XS. In conjuction with the Opus 21
compact disc player, the XS creates a complete 2-channel high performance audio system.

Unpacking

After unpacking your Opus 21 XS, inspect it for any shipping damage and contact us immediately if any is found.
Do not connect to the Opus 21 system if you find any shipping damage.

Please keep all packing materials for future transport. Shipping the Opus 21 in anything other than its original
crate may result in damage that is not covered by warranty. If you require a replacement crate or packing
materials, please contact Resolution Audio.

Should you need to repack the unit, be certain to place it between the supplied foam sheets,
with the accessory box on top.

The accessory box contains the following items:
Remote control
(2) AAA batteries
Digital cable for connection to Opus 21 cd player
AM loop antenna

To install the batteries in the remote control, open the cover on the back of the remote. Insert the batteries in
the orientation shown in the compartment, and replace the cover.

Installation

The XS must be used in conjuction with your Opus 21 cd player and Power Centre.

Your Power Centre may require a software update for use with the XS. Contact your dealer or Resolution Audio
directly for assistance.

Turn off the power to the Opus 21 at the rear of the Power Centre.

Prior to installation, all equipment should be turned off using the main power switch.

The XS must be located directly underneath your Opus 21 cd player.

First, remove the dust cover from the connector located on the bottom of your Opus 21 cd player. Next, position
the cd player directly on top of the XS, ensuring the connectors are aligned. Press the connectors firmly
together to secure the connection.

Using the XS with an Opus 21 series amplifier

The XS must be located directly above your amplifier.

Remove the dust cover from the connector located on the bottom of your Opus 21 XS. Next, position
the XS directly on top of the amplifier, and install it as the cd player was installed above.

Using the XS with another preamplifer or amplifier

Turn off all of your components prior to connecting the Opus 21.

This minimizes the chance of momentary electrical surges disturbing your system.

When using a preamp or integrated amplifier, use the fixed outputs.

With all of your equipment turned off, connect the analog outputs labeled FIXED to any line-level input of
your preamp or integrated amp.

When using a power amplifer, use the variable outputs.

With all of your equipment turned off, connect the analog outputs labeled VAR to the inputs of your amplifier.

Turn on the main power switch of the Opus 21 Power Centre.

The ON position is selected when the | symbol on the switch is depressed. The Opus 21 will take a few seconds
to initialize and read the disc if present. The Opus 21 initially sets the volume to a low level (50).

Turn on the rest of your system.

It is a good habit to turn the amplifier on last, and off first, to prevent surges and transients from reaching
your loudspeakers.

Insert a disc and press PLAY, or select any of the sources provided by the XS.

Adjust the volume. When using the FIXED outputs, the volume is controlled by your preamp or integrated amp.

Safety Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTIO N

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

The lightning flash with an arrowhead symbol, within
an equilateral triangle, is inteneded to alert the user to
the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral triangle
is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.

Check that the operating voltage of your unit
is identical to that of your local power supply.

Replace fuses only with identically rated
fuses.

To reduce risk of electrical shock, keep the
unit dry and grounded. Do not operate the
unit near water.

If the unit causes RF interference with another
product, move one unit or both until the
interference is eliminated. If the interference
cannot be sufficiently reduced, cease
operation and consult Resolution Audio.

Clean the chassis, faceplate, and controls with a soft
cloth lightly moistened with mild detergent solution. Do
not use any type of abrasive pad, scouring powder, or
solvent such as alcohol or benzine.

Do not discard the original box and packing materials.
When shipping the unit to another location or for repair
work, repack in original material.

Do not attempt to service this product. All servicing
should be referred to qualified service personnel.

Do not install the unit in a location near heat sources
such as radiators or heat ducts, or in a place subject
to mechanical vibration or shock.