Page 1
English 1
VPAP™ Adapt
POSITIVE AIRWAY PRESSURE DEVICE
H5i™
HEATED HUMIDIFIER
ClimateLine™ / ClimateLine
MAX™
/ SlimLine™ / Standard
AIR TUBING
Information Guide
English
Please read the entire Information and Welcome Guides before using your device.
CAUTION
In the US, Federal law restricts this device to sale by or on the order of a physician.
VPAP Adapt indications for use
The VPAP Adapt is indicated for the treatment of patients weighing more than 66 lb (30 kg) with
obstructive sleep apnea (OSA), central and/or mixed apneas, or periodic breathing. The VPAP Adapt is
intended for home and hospital use.
VPAP Adapt contraindications
Positive airway pressure therapy may be contraindicated in some patients with the following preexisting conditions:
• severe bullous lung disease
• pneumothorax or pneumomediastinum
• pathologically low blood pressure, particularly if associated with intravascular volume depletion
• dehydration
• cerebrospinal fluid leak, recent cranial surgery, or trauma.
Page 2
2
VPAP Adapt adverse effects
Patients should report unusual chest pain, severe headache, or increased breathlessness to their
prescribing physician. An acute upper respiratory tract infection may require temporary
discontinuation of treatment.
The following side effects may arise during the course of therapy with the device:
• drying of the nose, mouth, or throat
• nosebleed
• bloating
• ear or sinus discomfort
• eye irritation
• skin rashes.
H5i indications for use
The H5i is indicated for the humidification of the air delivered from a CPAP or bilevel device. The H5i
is for use only as recommended by a physician. The H5i is intended for single patient re-use in the
home environment and re-use in a hospital/institutional environment.
H5i contraindications
The H5i is contraindicated for use with patients whose upper (supraglottic) airway has been
bypassed.
Troubleshooting
If there is a problem, try the following suggestions. If the problem cannot be solved, contact your
equipment supplier or ResMed. Do not attempt to open the device or the H5i enclosure.
Problem/Possible cause Solution
No display
Power is not connected. Ensure the power cord is connected and the power outlet (if
available) is on.
The DC plug is partially inserted
into the back of the device or
inserted too slowly.
Fully insert the DC plug.
The VPAP Adapt and H5i are not
connected correctly.
Ensure that the VPAP Adapt and H5i are securely attached.
Page 3
English 3
Problem/Possible cause Solution
Insufficient air delivered from the device
Ramp time is in use. Wait for air pressure to build up or change ramp time.
Air filter is dirty. Replace air filter.
Air tubing is not connected
properly.
Check air tubing.
Air tubing is blocked, pinched or
punctured.
Unblock or free the air tubing. Check the air tubing for punctures.
Mask and headgear are not
positioned correctly.
Adjust position of mask and headgear.
Incorrect air tubing selected. If you are using the SlimLine, Standard or 3 m air tubing ensure
that you have the correct air tubing selected via the menu.
The H5i flip lid is not latched
correctly.
Close the flip lid ensuring that it clicks into place.
The H5i flip lid seal is not fitted
correctly.
Make sure the flip lid seal is facing the right way up and fitted
securely.
Non-vented mask is used. Only use a vented mask.
Mask vents might be blocked. Check if you have sufficient venting. Unblock mask vents if
necessary.
EPAP may be set too low. Talk to your clinician about your settings.
Device does not start when you breathe into the mask
Breath is not deep enough to
trigger SmartStart/Stop.
Take a deep breath in and out through the mask.
SmartStart/Stop is disabled
because Leak Alert is enabled.
Press Start/Stop to start therapy.
SmartStart/Stop is disabled. Talk to your clinician about enabling the SmartStart/Stop feature.
There is excessive leak. Adjust position of mask and headgear.
Connect the air tubing firmly at both ends.
Page 4
4
Problem/Possible cause Solution
Device does not stop when you remove your mask
SmartStart/Stop is disabled
because Leak Alert is enabled.
Press Start/Stop to stop therapy.
SmartStart/Stop is disabled. Talk to your clinician about enabling the SmartStart/Stop feature.
SmartStart/Stop is enabled but the device does not stop automatically when you remove your
mask
Incompatible mask system
being used.
Only use equipment recommended by ResMed.
Incorrect mask setting being
used.
Check the selected mask type in the Setup menu. Change it if
necessary.
The patient is using a nasal
pillows mask with a set
pressure less than 6 cm H
2
O.
Disable SmartStart/Stop.
Pressure rises inappropriately
Talking, coughing or breathing in
an unusual manner.
Avoid talking with a nasal mask on, and breathe as normally as
possible.
Mask cushion is buzzing against
the skin.
Adjust the headgear.
Cushion seated incorrectly
causing excessive leak.
Adjust headgear or re-fit cushion.
Displays message: Heated tube fault, replace tube
Device has been left in a hot
environment.
Allow to cool before re-use. Disconnect the power cord and then
reconnect it to restart the device.
There is a fault in your
ClimateLine or ClimateLine
MAX
heated air tubing.
Discontinue using your ClimateLine or ClimateLine
MAX
heated air
tubing and contact your clinician/service provider. Use SlimLine,
Standard or 3 m air tubing in the interim.
Page 5
English 5
Problem/Possible cause Solution
Displays message: Humidifier fault, replace humidifier
Device has been left in a hot
environment.
Allow to cool before re-use. Disconnect the power cord and then
reconnect it to restart the device.
There is a fault in your
humidifier.
Discontinue using your humidifier and contact your clinician/service
provider.
Refilling the humidifier with cold
water while humidifier is still hot
after therapy.
Allow to cool before re-use. Ensure the humidifier is filled with
water before the start of therapy to avoid running out of water
during therapy.
Filling the humidifier with ice
cold water on a warm day or
with hot water.
Use room temperature water.
Displays message: High temperature fault, refer to user manual
Device has been left in a hot
environment.
Allow to cool before re-use. Disconnect the power cord and then
reconnect it to restart the device.
Air filter is blocked. Replace your air filter. Disconnect the power cord and then
reconnect it to restart the device.
Air tubing is blocked. Check your air tubing and remove any blockages. Disconnect the
power cord and then reconnect it to restart the device.
Humidity level setting is too
high, resulting in accumulation
of water in the air tubing.
Turn the humidity level setting down and empty the water from
the air tubing.
Displays message: Check ResMed 30/90W Power Supply Unit and fully insert the connector
The DC plug is partially inserted
into the back of the device or
inserted too slowly.
Fully insert the DC plug.
A non-ResMed power supply
unit is connected to the device.
Remove the power supply unit and replace with a ResMed power
supply unit.
The power supply unit is being
covered by bedding.
Make sure that the power supply unit is free from bedding, clothes
or other objects that could cover it.
Page 6
6
Problem/Possible cause Solution
Displays message: No tube, please check your tube is connected
Flow is high because air tubing
is not connected properly.
Note: The tube disconnection
check may not operate when an
antibacterial filter is used.
Connect the air tubing firmly at both ends.
Displays message: Tube blocked, please check your tube
Air tubing is blocked. Check your air tubing and remove any blockages. Disconnect the
power cord and then reconnect it to restart the device.
Displays message: High leak, please check system setup and all connections
There is excessive leak.
Note: If Leak Alert is enabled,
an audible alert is activated and
a high leak message is
displayed.
Adjust position of mask and headgear.
Connect the air tubing firmly at both ends.
The H5i flip lid is not latched
correctly.
Close the flip lid ensuring that it clicks into place.
Displays message: Please close H5i flip lid, attach tube and press any key.
H5i flip lid is not closed. Close the flip lid ensuring that it clicks into place.
Air tubing is not connected
properly.
Connect firmly at both ends.
The following message is displayed on the LCD after you try to update settings or copy data to
the SD card: Card error, please remove SD card and contact service provider
SD card is not inserted correctly. Ensure that the SD card is inserted correctly.
Page 7
English 7
Problem/Possible cause Solution
You may have removed the
SD card before settings were
copied to the device.
Reinsert the SD card and wait for the Home screen or the
"Settings updated successfully, press any key" message to
appear on the LCD.
Note: This message only appears once. If you re-insert the SD card
after you have updated your settings, the message will not be redisplayed.
The following message is NOT displayed on the LCD after you try to update the settings using
the SD card: Settings updated successfully, press any key
The settings were not updated. Contact your clinician/service provider immediately.
Water splashing on your face from the H5i
The water tub is overfilled. Check that the water level is below the maximum water level
mark.
Condensation is forming in the
air tubing and mask.
Turn the humidity level setting down via the menu.
Leaking water tub
The water tub may be damaged
or cracked.
Contact your service provider for a replacement.
The cleanable water tub is not
assembled correctly.
Check for damage and reassemble the cleanable water tub
correctly.
Air feels too warm/cold in the mask
The temperature of the
ClimateLine or ClimateLine
MAX
heated air tubing is set too
high/low.
Turn up/down the heated air tubing temperature via the menu.
Page 8
8
General technical specifications
Power supply 90W power supply unit
Input range: 100–240V, 50–60Hz, 115V, 400Hz nominal for aircraft use
Typical power consumption: 70W (80VA)
Maximum power consumption: 110W (120VA)
30W power supply unit
Input range: 100–240V, 50–60Hz, 115V, 400Hz nominal for aircraft use
Typical power consumption: 20W (40VA)
Maximum power consumption: 36W (75VA)
90W DC/DC converter
Nominal inputs: 12V, 24V
Typical power consumption: 70W
Maximum power consumption: 110W
Environmental
conditions
Operating temperature: 41°F to 95°F (+5°C to +35°C)
Note: The air flow for breathing produced by this therapy device can be higher
than the temperature of the room. Under extreme ambient temperature
conditions (104ºF / 40ºC) the device remains safe.
Operating humidity: 10 to 95% non-condensing
Operating altitude: Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to
738 hPa
Storage and transport temperature: -4°F to 140°F (-20°C to +60°C)
Storage and transport humidity: 10 to 95% non-condensing
Aircraft use ResMed confirms that the device/s meets the Federal Aviation Administration
(FAA) requirements (RTCA/DO-160, section 21, category M) for all phases of air
travel.
Electromagnetic
compatibility
Product complies with all applicable electromagnetic compatibility requirements
(EMC) according to IEC60601-1-2, for residential, commercial and light industry
environments.
It is recommended that mobile communication devices are kept at least 1 m
away from the device.
Information regarding the electromagnetic emissions and immunity of this
ResMed device can be found on www.resmed.com, on the Products page
under Service and Support. Click on the PDF file for your language.
IEC 60601-1
classification
Class II (double insulation), Type BF, Ingress protection IP21
Page 9
English 9
VPAP Adapt technical specifications
Mode pressure
ranges
CPAP mode
Set Pressure: 4–20 cm H
2
O
ASV and ASVAuto mode
EPAP: 4–15 cm H
2
O; PS: 0–20 cm H2O
Maximum single
fault pressure
Maximum single fault steady state pressure: 30 cm H
2
O—if pressure exceeded
for > 6 sec; 40 cm H
2
O—if pressure exceeded for >1 sec
Physical Nominal dimensions (L x W x H): 6.0" x 5.5" x 3.4" (153 mm x 140 mm x 86 mm)
Weight: 1.84 lb (835 g)
Housing construction: Flame retardant engineering thermoplastic
Air outlet: 22 mm conical air outlet (complies with ISO 5356-1:2004)
Air filter
Hypoallergenic air filter: Acrylic and polypropylene fibers in a polypropylene
carrier
Standard air filter: Polyester non-woven fiber
Sound
DECLARED
DUAL-NUMBER
NOISE EMISSION
VALUES in
accordance with
ISO 4871:1996
Pressure level (CPAP mode)
With SlimLine air
tubing:
26 dBA with uncertainty of 2 dBA as measured according
to ISO 17510 1:2007
With Standard air
tubing:
27 dBA with uncertainty of 2 dBA as measured according
to ISO 17510 1:2007
With either SlimLine
or Standard air
tubing and H5i:
28 dBA with uncertainty of 2 dBA as measured according
to ISO 17510 1:2007
Power level (CPAP mode)
With SlimLine air
tubing:
34 dBA with uncertainty of 2 dBA as measured according
to ISO 17510 1:2007
With Standard air
tubing:
35 dBA with uncertainty of 2 dBA as measured according
to ISO 17510 1:2007
With either SlimLine
or Standard air
tubing and H5i:
36 dBA with uncertainty of 2 dBA as measured according
to ISO 17510 1:2007
Supplemental
oxygen
Recommended maximum supplemental oxygen flow:
15 L/min (CPAP, ASV modes); 4 L/min (ASVAuto mode)
Page 10
10
H5i technical specifications
Temperature Maximum heater plate temperature: 150°F (65°C)
Temperature cut-out: 165°F (74°C)
Maximum gas temperature: ≤ 106°F (≤ 41°C)
Physical Dimensions (L x W x H): 6.0" x 5.7" x 3.4" (153 mm x 145 mm x 86 mm)
Weight (water tub): Docking station and unfilled water tub 1.5 lb (0.67 kg)
Weight (cleanable water tub): Docking station and unfilled water tub 1.7 lb (0.77
kg)
Water capacity: To maximum fill line 380 mL
Materials Docking station: Flame retardant engineering thermoplastic, aluminium
Water tub: Injection molded plastic, aluminium and thermoplastic elastomer
Cleanable water tub: Injection molded plastic, stainless steel and silicone seal
Air tubing technical specifications
Air tubing Material Length Inner diameter
ClimateLine heated air tubing Flexible plastic and electrical
components
6'6" (2 m) 0.6" (15 mm)
ClimateLine
MAX
heated air
tubing
Flexible plastic and electrical
components
6'3" (1.9 m) 0.75" (19 mm)
SlimLine air tubing Flexible plastic 6' (1.8 m) 0.6" (15 mm)
Standard air tubing Flexible plastic 6'6" (2.0 m) 0.75" (19 mm)
3 m air tubing Flexible plastic 9'10" (3.0 m) 0.75" (19 mm)
Heated air tubing temperature cut-out: ≤ 106°F (≤ 41°C)
Notes:
• The manufacturer reserves the right to change these specifications without notice.
• The temperature and relative humidity settings displayed for Climate Control are not measured
values.
• Check with your clinician/service provider before using the SlimLine air tubing with devices other
than the S9 or H5i.
• The electrical connector end of the heated air tubing is only compatible with the H5i air outlet
and should not be fitted to the device or mask.
Page 11
English 11
• When using the SlimLine or ClimateLine above 20 cm H
2
O, the device optimum performance
may not be reached if used with an antibacterial filter. The device performance must be checked
prior to prescribing the SlimLine for use with an antibacterial filter.
• The ClimateLine or ClimateLine
MAX
is designed only for use with the H5i.
Humidifier performance
The following settings have been tested at 71.6°F (22°C) ambient temperature:
Mask pressure
cm H2O
RH output % Nominal system output AHa, BTPSb
Setting 3 Setting 6 Setting 3 Setting 6
3 90 100 10 18
10 95 100 11.5 21
20 95 100 11 18
25 100 100 12 13.5
a. AH - Absolute Humidity in mg/L.
b. BTPS - Body Temperature Pressure Saturated.
Pneumatic flow path
1. Flow sensor
2. Blower
3. Pressure sensor
4. Mask
5. Air tubing
6. H5i
7. Device
8. Inlet filter
Page 12
12
Displayed values
Value Range Display resolution
Pressure sensor at air outlet
Mask pressure 4–20 cm H2O (CPAP); 4–25 cm
H
2
O (ASV, ASVAuto)
0.1 cm H
2
O
Flow derived values
Leak 0–200 L/min 1 L/min
Tidal volume
0–4000 mL
1 mL
Respiratory rate 0–50 BPM 1 BPM
Minute ventilation 0–30 L/min 0.1 L/min
Value Accuracya
Pressure measurementa
Mask pressure ±0.5 cm H2O (+4% of measured value)
Flow measurements
a
Leakb ±12 L/min or 20% of reading, whichever is greater, at 0 to 60
L/min
Tidal volume
b.c
±20%
Respiratory rate
b, c
±1 BPM
Minute ventilation
b, c
±20%
a. Results are expressed at ATPD (Ambient Temperature and Pressure, Dry).
b. Accuracy may be reduced by the presence of leaks, supplemental oxygen, tidal volumes <100 mL
or minute ventilation <3 L/min.
c. Measurement accuracy verified as per ISO 10651-6:2004 for Home Care Ventilatory Support
Devices (Figure 101 and Table 101).
Page 13
English 13
Flow (maximum) at set pressures
The following are measured at the end of the specified air tubing:
Pressure, cm H2O VPAP Adapt and
Standard, L/min
VPAP Adapt, H5i
and Standard,
L/min
VPAP Adapt and
SlimLine, L/min
VPAP Adapt, H5i
and ClimateLine,
L/min
4 200 170 195 170
8 200 170 190 170
12 200 170 184 170
16 200 170 175 170
20 190 170 168 161
25 180 161 144 125
Symbols
The following symbols may appear on your product or packaging.
Caution; Read instructions before use; Protection against insertion of fingers and against
vertically dripping water;
Type BF equipment; Class II equipment; Start/Stop;
Manufacturer; European Authorized Representative; European RoHS;
Batch code; Catalogue number; Serial number; Direct current;
Lock/unlock; China pollution control logo 1; China pollution control logo 2;
Not drip proof; Keep dry; Not for use on more than one patient.; Maximum water
level;
Disinfectable up to 200°F (93°C); Use distilled or deionized water only;
Remove tub to fill; Follow instructions for use; Prescription only (In the US,
Federal law restricts these devices to sale by or on the order of a physician.);
Page 14
14
Environmental information
WEEE 2002/96/EC is a European Directive that requires the proper disposal of electrical and
electronic equipment. This device should be disposed of separately, not as unsorted municipal waste.
To dispose of your device, you should use appropriate collection, reuse and recycling systems
available in your region. The use of these collection, reuse and recycling systems is designed to
reduce pressure on natural resources and prevent hazardous substances from damaging the
environment.
If you need information on these disposal systems, please contact your local waste administration.
The crossed-bin symbol invites you to use these disposal systems. If you require information on
collection and disposal of your ResMed device please contact your ResMed office, local distributor or
go to www.resmed.com/environment.
Servicing
The VPAP Adapt and H5i are intended to provide safe and reliable operation when operated in
accordance with the instructions provided by ResMed. ResMed recommends that the VPAP Adapt
and H5i be inspected and serviced by an authorized ResMed Service Center if there is any sign of
wear or concern with device function. Otherwise, service and inspection of the devices generally
should not be required during the five year design life of the device.
Limited warranty
ResMed Ltd (hereafter 'ResMed') warrants that your ResMed product shall be free from defects in
material and workmanship from the date of purchase for the period specified below.
Product Warranty period
•
Mask systems (including mask frame, cushion, headgear and
tubing)—excluding single-use devices
• Accessories—excluding single-use devices
• Flex-type finger pulse sensors
•
Humidifier water tubs
90 days
• Batteries for use in ResMed internal and external battery
systems
6 months
Page 15
English 15
Product Warranty period
• Clip-type finger pulse sensors
• CPAP and bilevel device data modules
• Oximeters and CPAP and bilevel device oximeter adapters
• Humidifier cleanable water tubs
•
Titration control devices
1 year
• CPAP, bilevel and ventilation devices (including external
power supply units)
• Humidifiers
• Battery accessories
•
Portable diagnostic/screening devices
2 years
This warranty is only available to the initial consumer. It is not transferable.
If the product fails under conditions of normal use, ResMed will repair or replace, at its option, the
defective product or any of its components.
This Limited Warranty does not cover: a) any damage caused as a result of improper use, abuse,
modification or alteration of the product; b) repairs carried out by any service organization that has not
been expressly authorized by ResMed to perform such repairs; and c) any damage or contamination
due to cigarette, pipe, cigar or other smoke.
Warranty is void on product sold, or resold, outside the region of original purchase.
Warranty claims on defective product must be made by the initial consumer at the point of purchase.
This warranty replaces all other expressed or implied warranties, including any implied warranty of
merchantability or fitness for a particular purpose. Some regions or states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you.
ResMed shall not be responsible for any incidental or consequential damages claimed to have
resulted from the sale, installation or use of any ResMed product. Some regions or states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation may
not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
region to region. For further information on your warranty rights, contact your local ResMed dealer or
ResMed office.
Page 16
16
WARNINGS
• Read the entire manual before using the device.
• Use the device only as directed by your physician or healthcare provider.
• Use the device only for the intended use as described in this manual. Advice contained in this
manual should not supersede instructions given by the prescribing physician.
• If you notice any unexplained changes in the performance of the device, if it is making unusual
or harsh sounds, if the device or the power supply are dropped or mishandled, if water is spilled
into the enclosure, or if the enclosure is broken, discontinue use and contact your ResMed
Service Center.
• Beware of electrocution. Do not immerse the device, humidifier, power supply or power cord in
water. In the event of a spill, disconnect the device from the power supply and let the parts dry.
Always unplug the device before cleaning and make sure that all parts are dry before plugging in
the device.
• Explosion hazard—do not use in the vicinity of flammable anesthetics.
• Make sure the power cord and plug are in good condition and the equipment is not damaged.
• Keep the power cord away from hot surfaces.
• The device should only be used with masks (and connectors
1
Explanation: The device is intended to be used with special masks (or connectors) which have
vent holes to allow continuous flow of air out of the mask. When the device is turned on and
functioning properly, new air from the device flushes the exhaled air out through the mask vent
holes. However, when the device is not operating, insufficient fresh air will be provided through
the mask, and the exhaled air may be rebreathed. Rebreathing of exhaled air for longer than
several minutes can, in some circumstances, lead to suffocation. This applies to most models of
CPAP or bilevel devices.
) recommended by ResMed, or by
a physician or respiratory therapist. A mask should not be used unless the device is turned on.
Once the mask is fitted, ensure that the device is blowing air. The vent hole or holes associated
with the mask should never be blocked.
• Oxygen supports combustion. Oxygen must not be used while smoking or in the presence of an
open flame.
• Always ensure that the device is turned on and airflow generated before the oxygen supply is
turned on. Always turn the oxygen supply off before the device is turned off, so that unused
oxygen does not accumulate within the device enclosure and create a risk of fire.
1
Ports may be incorporated into the mask or in connectors that are near the mask.
Page 17
English 17
• Do not operate the H5i if it is not working properly or if any part of the bilevel device or H5i has
been dropped or damaged.
• Do not leave long lengths of air tubing around the top of your bed. It could twist around your
head or neck while you are sleeping.
• Do not use electrically conductive or antistatic air tubings.
• Do not use the air tubing if there are any visible signs of damage.
• Only ResMed air tubing and accessories should be used with the device. A different type of air
tubing or accessory may alter the pressure you actually receive, reducing the effectiveness of
the treatment.
• Only use the ResMed 90W or 30W power supply unit. Use the 90W power supply unit to power
the system comprising the device, H5i, air tubing, DC/DC converter and battery pack. The 30W
power supply unit is designed to power the device only and recommended for travelling.
• Only ResMed products are designed to be connected to the module connector port. Connecting
other devices could damage the device.
• Blocking the air tubing and/or air inlet of the device while in operation could lead to overheating
of the device.
CAUTIONS
• Do not open the device enclosure. There are no user serviceable parts inside. Repairs and
servicing should only be performed by an authorised ResMed service agent.
• Do not use bleach, chlorine, alcohol, or aromatic-based solutions, moisturizing or antibacterial
soaps or scented oils to clean the device, humidifier or air tubing. These solutions may cause
damage and reduce the life of these products.
• Incorrect system setup may result in incorrect mask pressure reading. Ensure the system is
correctly set up.
• Be careful not to place the device where it can be bumped or where someone is likely to trip
over the power cord.
• Make sure that the area around the device is dry and clean and clear of bedding, clothes or other
objects that could block the air inlet or cover the power supply unit.
• Ensure that the device is protected against water if used outdoors. Enclose the device in the S9
travel bag for transport.
• Do not open the H5i enclosure. There are no user serviceable parts inside. Repairs and servicing
should only be performed by an authorised ResMed service agent.
• The H5i should only be used with tubing or accessories recommended by ResMed. Connection
of other delivery tubes or accessories could result in injury, or damage to the device.
Page 18
Global leaders in sleep and respiratory medicine www.resmed.com
• Do not overfill the water tub as water may enter the device and air tubing.
• Do not use any additives (eg, scented oils or perfumes). These may reduce the humidification
output of the H5i and/or cause deterioration of the water tub materials.
• Take care when handling your H5i as the water/water tub may be hot. Allow 10 minutes for the
heater plate and any excess water to cool.
• The H5i should only be connected or disconnected when the water tub is empty.
• Make sure that the water tub is empty before transporting the H5i.
• Do not operate the H5i on an aircraft as water may enter the bilevel device and air tubing during
turbulence.
• Always place the H5i on a level surface below the level of the user to prevent the mask and
tubing from filling with water.
• If liquids are inadvertently spilled into or on the H5i, unplug the device from the power outlet.
Disconnect the H5i from the device and allow the H5i to drain and dry before re-using.
Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center
Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other
ResMed locations worldwide.
For patent information, see www.resmed.com/ip.
S9, H5i, ClimateLine, SlimLine, SmartStart and VPAP are trademarks of ResMed Ltd. S9, ClimateLine, SlimLine, SmartStart and VPAP are registered in U.S.
Patent and Trademark Office.
© 2012 ResMed Ltd. 368792/2 2012-05
Loading...