This user manual prvides the operation, regular
maintenance and safety information.
Read this user manual carefully before you use
and save it for future reference.
The manual contains warranty card. Keep it for
future service use.
Rev 1.1
XD100
Charger
USB cable
Part number: CAD0002
Part number: CAD0001
Calibrator Cap(optional)
Traveler bag(optional)
Calibrator Cap : Ozone comes with its natural odour which may be
unpleasant to some users. Although Ozone is cleared off by itself in hours, the
optional calibrator cap offers an immediate residual ozone removal in CPAP.
After each disinfection cycle, apply calibrator cap to one end of tubing usually
connected to mask. When CPAP is powered on, it emulates the CPAP is
being used and blow off fresh air to remove the residual Ozone in minutes.
Traveler bag : Use the traveler bag to carry RESCOMF XD100 and/or
accessories. It can also be used to enclose your Full Face or Nasal mask for
disinfection cycle.
Important! To ensure the electrical charging specifications are followed
please use the approved Charger and USB cable.
XD100, Charger, USB cable, User Manual (with warranty card inside), QA
Certificate, Calibrator Cap (optional) and Traveler bag (optional)
Thank You for purchasing RESCOMF Ventilation Disinfector XD100, it is
proven Ozone kills 99.99% of germs and bacteria.You can sanitize your
CPAP machine and related accessories(e.g.mask,tubing...) completely
through a stream of controlled Ozone for approximately 30 minutes.The
entire care free and dry sanitization process requires no water soap or
chemical cleaning.
Keep out of reach of children. Do not let children play with the product.
This product contains rechargeable battery. To support GREEN, Please do not dispose
of the product in the household waste at the end of its useful life.
Environmental Notice
Safety Precautions
Product Structure
~
~ 45℃
Technical Specifications
Specifications
1.Size:
2.Weight
3.Rechargeable Lithium-ion battery 2000mAh
4.Power：
5.Storage temperature：
6.Operating temperature：
7.IPX1 IP (Ingress protection)：
XD100 disinfection connection diagram
CPAP
Tubing
Ventilation Disinfector
Operation Instruction
117x68x50(mm)
205g
3W
-20℃ 55℃
-5℃
IPX1
On/Off button
XD100 has optimized its sanitization cycle to 35 minutes including 30
minutes with ozone and 5 minutes with fresh air. Repeating the cycle is
not necesary.
The manufacturer reserves the right to change the above specifications
without notice.
Power-off the CPAP/ Bi-PA. Drain water in CPAP reservoir. Connect the
Ventilation disinfector to CPAP by tubing.
For better disinfecion result, better put the CPAP and Ventilation disinfector
inside a enclosing container (e.g the CPAP bag).
Turn on : Press and Hold the On/Off button for few seconds till the buzzer
beeps once and Working indicator stays Green. Ozone will start streaming.
Operating : Once the Ventilation Disinfector starts working, Ozone will start
streaming for 30 minutes then fresh air for 5 minutes. The last 5 minutes
fresh air will clear off most of the residual ozone which may be unpleasant
to some users. Green working light stays ON during the 35 minutes.
Auto Stop : After the programmed sanitization cycle for 35 minutes, the
machine will automatically power off and generate five beeps sound.
working indicator will be off.
If for any reasons the user wants to manual turn off the power during
sanitization process, press and hold the On/Off button for few seconds.
The machine will be off with a long beep sound indicating the machine is
power off. Working indicator will be off.
Charging the battery
The Ventilation Disinfector includes a rechargeable battery. For charging
the battery, connect the product as shown in the illustration - connect the
USB cable to charging port and power adaptor. Insert the power adaptor
into a power outlet.
The 2000 mAh rechargeable batteries meets most of the airlines restriction.
It is recommended to sanitize the CPAP, tubing and mask weekly.
For the best lithium battery performance and battery life, set the power
off while it is at charging. Charging indicator turns red when it is at
charge.Charging indicator turns green when charging is completed.
The time required to recharge the battery will vary greatly depending on
the ambient temperature and the battery’ s remaining capacity. If the
battery becomes exhausted quickly even after being fully charged, the
battery has reached the end of its service life.
Low Power indication : When the battery is running low, Working
indicator blinks along with long buzzer sound. The disinfector will
continue to operate till the battery charge is completed used up; however,
it does not warrant a complete 35 minutes sanitization cycle.
Recommend user charges up the disinfector once the working indicator
flashes.
For the CPAP machine configured with humidifier, drain water in reservoir
before starting the sanitization process.
After Sanitization process, wait for an hour before using the CPAP for
ensuring no ozone residue odour.
The user can turn on the CPAP after sanitization to remove the residue
ozone odour. If wants to shorten the residue ozone removal time, the user
can order a calibrator cap putting on the CPAP tubing end for forcing the
residue ozone odour clear out.
Ozone concentration is designed by the disinfector design, enclosing
container and sanitaization time. The machine design is based on the
best sanitization performance. User is not recommended to change any
settings.
RESCOMF offers a 1 year warranty on the product commencing on the date
of purchase. For related accessories warranty period is 90 days.
The warranty does not cover damage due to improper use and normal wear.
The warranty only covers defects in the prduct resulting from faults in material
or workmanship, free of charge either by repairing or replacing in the
complete product at RESCOM discretion.
The warranty becomes VOID if repairs are undertaken by unauthorized
persons and if original RESCOMF parts are not used. To obtain service
within the warranty period,Please contact your distributor.
Limited Warranty
Important Notes
Troubles shooting
The product does not
work after turn on
Charging indicator not
light up
No Ozone generation
Problem
Possible solution(s)
Warranty card
Customer name Contact phone number
Contact address
Product Series no
Purchasing date
Distributor Name/ Stamp
Repair date
Repair records
Main Unit
Accessories
Check the Charger connection is correct. If
still not resolve the problem, send the
product for repairing.
Battery is charged but
product still not working
With no beep sound
machine stop
After 35 minutes, machine
not stop automatically
If after press the On/Off button, working
indicator no light and fan is not working,
connect the product to power Charger and
plug the charger to power outlet. Turn on
the product.
If working indicator turns on with green light
but fan still does not working, send the
product for repairing.
Power up the machine again. If still cannot
resolve the problem, send the product for
0repairing.
Battery is used up. Connect the product to
power charger for charging.
Make sure the battery has been charged.
Check the charging connection.
Connect the product to Charger. Plug
the Charger to power outlet. Turn on the
product.
Keep the warranty card and Sales receipt. The card is valid with
distributor stamp or Sales receipt. Thank you for cooperation.
Loading...