Renu Electronics FlexiPanels FP4 Series, FP4043T, FP4043TN, FP4070T, FP4070TN User Manual

...

Download

User Manual

FlexiPanels®Advance HMI

FP4 Series

FlexiPanels® Advance HMI

Page 2 of 17

Table of Contents

INTRODUCTION ................................................................................................................................................... 3

BEFORE YOU START .............................................................................................................................................. 3

SAFETY PRECAUTIONS .......................................................................................................................................... 4

PRODUCT OVERVIEW ........................................................................................................................................... 5

INSTALLING FP4 PRODUCTS ........................................................................................................................................ 5

ANEL GUIDELINES ................................................................................................................................................................ 5

ANEL CUTOUT DIMENSIONS .................................................................................................................................................. 5

RODUCT DIMENSIONS .......................................................................................................................................................... 5

INIMUM CLEARANCES ......................................................................................................................................................... 7

OUNTING FP4 PRODUCTS .................................................................................................................................................... 7

ONNECTING POWER ............................................................................................................................................................. 7

ROUNDING ......................................................................................................................................................................... 7

PRODUCT SPECIFICATIONS ................................................................................................................................... 8

PRODUCT NOMENCLATURE / ORDERING PART NUMBER ................................................................................................... 8

ISPLAY SPECIFICATIONS ............................................................................................................................................ 8

CPU,

MEMORY AND POWER SUPPLY ............................................................................................................................ 9

OWER RATING ..................................................................................................................................................................... 9

OMMUNICATION INTERFACES .................................................................................................................................. 10

RS232

/ RS422 / RS485 PORT ............................................................................................................................................ 10

THERNET PORT .................................................................................................................................................................. 12

USB

DEVICE PORT ............................................................................................................................................................... 12

USB

HOST PORT ................................................................................................................................................................. 12

TYPE CABLE...................................................................................................................................................................... 13

CARD SLOT .................................................................................................................................................................... 13

CCESSORIES ........................................................................................................................................................ 14

ROGRAMMING CABLE ........................................................................................................................................................ 14

OMMUNICATION CABLE ...................................................................................................................................................... 14

DEFAULT PRODUCT SETTING .............................................................................................................................. 15

ENVIRONMENTAL SPECIFICATIONS AND APPROVALS ....................................................................................................... 15

REVISION HISTORY ............................................................................................................................................. 16

NOTES ............................................................................................................................................................... 17

FlexiPanels® Advance HMI

Page 3 of 17

Introduction

FP4 Advance HMI series is a powerful, feature rich and versatile HMI product range with a complete range of screen size starting with compact 4.3” WQVGA TFT color display, covering most popular screen sizes in the industry (7”, 10.1”, 12.1”), till dynamic 15” XGA TFT color screen. These HMIs are powered by FlexiSoft® programming software and supports a powerful FlexiSoft® runtime for efficient performance. IEC61131-3 logic programming environment support give a unique edge to these products.

All the products are compliant to EMC directive 2014/30/EU and LVD directive 2014/35/EU and suitable for installation in hazardous locations, because they are listed for UL Class I Div. 2.

This user manual gives detailed information regarding the hardware specifications, operating conditions, installation, mounting and wiring. All the information published in this manual is produced and governed by Renu Electronics Pvt. Ltd. and is protected by Indian Copyright Act.

Before you start

 FlexiPanels® FP4 series products are general purpose human machine interface devices,

suitable for a variety of industrial applications across various industries. However, Renu Electronics is not responsible or liable for any indirect or consequential damage resulting from the use of this product.

 The user should check and confirm the suitability of the product before using in any specific

application.

 The diagrams and examples in this manual are included for illustration purpose only. Renu

Electronics assume no responsibility or liability regarding actual use based on these diagrams or examples.

 Reproduction of the contents of this manual, in any form (in part or in whole), is strictly

prohibited.

 Following table shows various symbols that may be used in this manual to provide information

regarding safety, precautions and usage of the product:

WARNING: Indicates circumstances that may cause an explosion in hazardous environment, which may lead to injury or death, damage or economic loss

CAUTION: Indicates specific precautions to be taken by user during installation, operation and maintenance of the product

ATTENTION

ATTENTION: Indicates important information regarding application and functions of

the product

FlexiPanels® Advance HMI

Page 4 of 17

Safety Precautions

This section of the manual provides information which is critical regarding safety and therefore the user is advised to go through the information in detail before installing the product. User may contact Renu Electronics technical support team at support@renuelectronics.com for any specific question(s) related to safety.

WARNING: EXPLOSION HAZARD

 Do not disconnect equipment unless power has been removed or the area is known

to be nonhazardous.

 Substitution of any component may impair suitability for Class I, Division 2.  Secure any external connections that mate to this equipment by using screws, sliding

latches, threaded connectors or any other means provided with this product.

 If this product contains batteries, they must only be changed in an area known to be

nonhazardous.

CAUTION: GENERAL PRECAUTIONS

 Do not use this product for emergency stop. A separate physical switch, outside the

product must be used for any emergency stop operations.

 Do not use the external power supply source that does not comply with the specified

power requirements of the product, it may cause malfunction or permanent damage to the product.

 Do not attempt to open, dismantle or modify the p

roduct, doing so will void the

warranty.

 This product is supplied as open-type equipment and it must be mounted within an

enclosure, suitably designed for specific environmental conditions.

 When used in Class I, Division 2 hazardous location, the product must be mounted

in a suitable enclosure with proper wiring method that complies with the governing electrical codes.

 The USB port is intended for temporary local programming purpose only and not

intended for permanent connection. If you connect or disconnect the USB cable with power applied to this product or any other device on USB network, and electrical arc can occur, which could cause explosion in hazardous location installations.

 Make sure that connectors are securely tightened to properly seal the connections

against leaks.



Do not place the product in direct sunlight. Prolonged exposure to sunlight may degrade the LCD and housing.

FlexiPanels® Advance HMI

Page 5 of 17

Product Overview

This section of the manual provides an overview of FP4 series products, its front and back view, installation details, dimensional details, mounting method and details.

Installing FP4 products

FP4 series products are designed for front panel mounting. Before installing the products, user should review the panel guidelines, panel cutout dimensions, product dimensions and minimum clearances.

Panel Guidelines

The panel must be at least 2mm (12gauge), so that it can provide the required support and proper sealing against water and dust. The panel surface must be flat, without any imperfection, to maintain adequate seal and IP rating. Maximum panel thickness allowed is 6mm (±0.2mm).

Panel Cutout Dimensions

The panel must be at least 2mm (12gauge), so that it can provide the required support and proper sealing against.

Model

Height (mm)

Width (mm)

FP4043T

111

FP4043TN

111

FP4070T

127

175

FP4070TN

127

175

FP4101T

178

256

FP4101TN

178

256

FP4121T

225

293

FP4121TN

225

293

FP4151T

285

386

FP4151TN

285

386

ATTENTION

ATTENTION: Panel cutout

 Before making panel cutout, disconnect all electrical power from the panel.  Make sure that area surrounding the panel cutout is clear.  Make sure that metal cutting does not enter any component already installed in the

panel.

Product Dimensions

This section of the manual provides dimensional details of FP4 series products. All the dimensions shown below are measured in mm.

FlexiPanels® Advance HMI

Page 6 of 17

FlexiPanels® Advance HMI

Page 7 of 17

Minimum Clearances

Maintain clearance from enclosure walls, wires and other adjacent devices. Keep 2” space on all sides for adequate ventilation. Plan for adequate space around the product and inside the enclosure for ventilation and cabling. Take into consideration the heat produced by other devices in the enclosure. The ambient temperature around this product must be -10° to 60°C.

Mounting FP4 Products

FP4 series products must be installed on the front panel, using the clamp accessories shipped with the product. Before mounting, make sure that sealing gasket is properly positioned. This gasket forms a compression type seal. Do not use sealing compounds. Then, place the unit in the panel cutout and tighten the mounting screws evenly (torque 0.4Nm) to maintain water and dust resistance.

ATTENTION

ATTENTION: Mounting FP4 on Panel

 Do not push LCD display when pushing the unit into the panel as it may damage the

display.

Connecting Power

FP4 series require 24VDC power supply. Follow the steps mentioned below to connect the power:

 Make sure that terminal is not connected to power source  Secure the 24VDC power wires  Secure the functional earth ground wire to the functional earth ground terminal screw on terminal

block

 Apply 24VDC power to the terminal

Grounding

The optimum method for grounding electronic equipment is to ground it separately from other high-power systems and to ground more than one unit of electronic equipment with a single-point ground. Following marked terminal is provided with the unit for grounding:

FlexiPanels® Advance HMI

Page 8 of 17

Product Specifications

This section of the manual provides detail specifications of FP4 series products, ordering part numbers, operating conditions, environment and approvals.

Product Nomenclature / Ordering Part Number

FP4 series has 5 models, depending on display size and each model has two variants, based on Ethernet and SD Card slot support. Detail part number or ordering information is as follows:

Display Specifications

FP4 series products support high quality color TFT display range.

Size: 4.3” WQVGA color TFT with 4-wire analog resistive touch screen

Resolution: 480 x 272pixels Brightness: 400cd/m

Backlight life: 30,000Hrs.

Size: 7” WVGA color TFT with 4-wire analog resistive touch screen

Resolution: 800 x 480pixels Brightness: 350cd/m

Backlight life: 30,000Hrs.

Size: 10.1” WVGA color TFT with 4-wire analog resistive touch screen

Resolution: 1024 x 600pixels Brightness: 350cd/m

Backlight life: 50,000Hrs.

Size: 12.1” SVGA color TFT with 4-wire analog resistive touch screen

Resolution: 800 x 600pixels Brightness: 500cd/m

Backlight life: 70,000Hrs.

Size: 15” XGA color TFT with 4-wire analog resistive touch screen

Resolution: 1024 x 768pixels Brightness: 400cd/m

Backlight life: 50,000Hrs.

FlexiPanels® Advance HMI

Page 9 of 17

CPU, Memory and Power Supply

Power Rating

Unit

Voltage

Current

Wattage

FP4043

24VDC

140mA

3.36W

FP4070

24VDC

320mA

7.68W

FP4101

24VDC

330mA

7.92W

FP4121

24VDC

420mA

10.08W

FP4151

24VDC

800mA

19.2W

ATTENTION

ATTENTION: Logging to External memory

 The Ethernet models of FP4 series supports SD card slot, which can be used to log

the data directly on SD card. MicroSD HC card with capacity between 4GB to 32GB is supported. Supported speed classes are as follows:

 While inserting or removing SD card, the device power must be turned off.

 The user must take periodic backup of logged data to avoid loss of data.

CPU: 32-bit RISC processor eMMC: 4GB

RAM: 512MB

User

Application

Up to 1GB that includes user

application, data log, alarms,

retentive memory and logic memory

Power Supply:

24VDC (±15%) with isolation

RTC:

Built-in, date and time function

FlexiPanels® Advance HMI

Page 10 of 17

Communication Interfaces

This section of the manual gives detail information regarding various communication interfaces supported by FP4 series products, including communication interfaces between FP4 and other RENU or any third-party device, interfaces for programming and monitoring.

RS232 / RS422 / RS485 Port

FP4 products support DB9 female port for RS232 / RS422 / RS485 communication. 4.3” and 7” models support one DB9 female port and 10.1”, 12.1” and 15” models support two DB9 female ports.

Pin number

Signal

TX+(RS422/RS485)

TXD(RS232)

RXD(RS232)

RX+(RS422/RS485)

GND

NC 7 NC

TX-(RS422/RS485)

RX-(RS422/RS485)

7” model support one terminal block port (COM 1).

Pin number

Signal

RX- 2 TX-

RX+

TX+

GND

RXD

TXD

FlexiPanels® Advance HMI

Page 11 of 17

ATTENTION

ATTENTION: DB9 port

 The 4.3” models have only one DB9 port that supports RS232 and RS422 / RS485

signal levels on different pins.

 If user wants to connect different devices on RS232 and RS422 / RS485 levels,

simultaneously with 4.3” HMI, then he must use ‘Y’ type cable.

FlexiPanels® Advance HMI

Page 12 of 17

Ethernet Port

FP2 series support Ethernet port as an ordering option. It’s having standard shielded RJ45 female jack with built-in speed and indication LED’S.

Pin number

Signal

TX+

TX-

RX+

NC 6 RX-

USB Device Port

FP4 products support one Micro USB port for programming and monitoring.

Pin number

Signal

VCC

D-

D+

GND

USB Host Port

FP4 products support one USB Host port that connects to USB 2.0 compatible pen drives. The pen drive can be used as external memory for data logging and transferring user application or firmware to the unit.

Pin number

Signal

VCC

D-

D+

GND

FlexiPanels® Advance HMI

Page 13 of 17

Y Type Cable

Special “Y” cable for FP unit (two communication levels on one port).

SD Card Slot

Ethernet models of FP4 products support one SD card slot. SD card can be used as external memory for data logging and transferring user application or firmware to the unit. MicroSD HC card with capacity between 4GB to 32GB is supported.

Following speed classes are supported:

FlexiPanels® Advance HMI

Page 14 of 17

Accessories:

Programming Cable (Download)

Micro USB

Part number: PC-USBAB-00-Micro

[Note: PC-USBAB-00: 2M cable, PC-USBAB-05: 5M cable, PC-USBAB-10: 10M cable]

Communication Cable

RS-232

Part number: IBM0909-1-00

[Note: IBM0909-1-00: 2M cable, IBM0909-1-05: 5M cable, IBM0909-1-10: 10M cable]

FlexiPanels® Advance HMI

Page 15 of 17

Default Product Setting

Network Setting

DHCP

Brightness

Full Scale

Beeper

Default Language

English

RTC Settings

Current Date/Month/Year Current Time

Environmental Specifications and Approvals

Feature

Specifications

Operating Temperature

-10° to 60°C

Storage Temperature

-20° to 85°C

Relative Humidity

10 to 95% non-condensing

Shock

IEC 60068-2-27

25g, 11ms, 6 shocks per axis,

total 18 shocks (X, Y, Z)

Vibration

IEC 60068-2-6 5 to 150Hz, 3g peak (X, Y, Z)

EMC

EN 55011 : 2009/A1 : 2010

EN 61131-2 : 2007 EN 61000-6-2 : 2005/AC : 2005

EN 61000-6-4 : 2007/A1 : 2011

Protection

IP66 for front panel mounting

Yes

Yes (Class I Division 2)

RoHS

Yes

[Note: For UL Operating Temperature range is 0-50°C]

FlexiPanels® Advance HMI

Page 16 of 17

Revision History

Revision

Description

Date

Prepared by

Approved by

1.0

First Draft

25/07/2018

1.1

1. Panel Cutout Information is Corrected

2. Added Power Rating in Product Specifications

3. Added Default Product Settings

07/12/2018

1.2

Ordering part number of 15" HMI is changed from

FP4150 to FP4151

13/12/2018

Renu Electronics reserves the right to change or discontinue specifications and features without prior notice.

FlexiPanels® Advance HMI

Page 17 of 17

NOTES

Renu Electronics FlexiPanels FP4 Series, FP4043T, FP4043TN, FP4070T, FP4070TN User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual