Renu Electronics FP4057T, FP4057T-E, FP4057TN-E, FP4057TN Quick Start Manual

Quick Start Manual for

FP4057 Models

Product Codes:
FP4057T: Flexi Panels, 320 x 240 QVGA, 5.7” Color

TFT, with no expansion slot.

FP4057T-E: Flexi Panels, 320 x 240 QVGA, 5.7” Color

TFT, with 5 expansion slots.

FP4057TN: Flexi Panels, 320 x 240 QVGA, 5.7” Color

TFT, Ethernet with no expansion slots.

FP4057TN-E: Flexi Panels, 320 x 240 QVGA, 5.7” Color

TFT, Ethernet with 5 expansion slots.

FP4057Tx-x Specifications

FP4057Txx is Flexi Panel series product.
Flexi Panel Series operator interfaces provide human-machine
interface for PLCs / Inverters. It communicates with PLCs /
Inverters over serial communication port to fetch the information.
Information can be displayed over LCD or can be used to build a
logic.

Specifications of FP4057Tx-x:
Power Supply: For FP4057T: 24VDC; 7W

Display: 5.7”TFT (320 x 240 Pixels)

Color Graphical Display
Bezel: IP 65 rated Keypad
LEDs: 7
Memory: 6 MB Max. Application Memory
Communication:
2 COM Ports: COM1 & COM2: RS232/RS485/RS422
USB Device: For Upload and Download
USB Host: For mass storage interface

Operating Temp.: 0 to 50 C
Humidity: 10% to 90% (Non condensing)
Panel cutout: 184.00 mm x 131.00 mm
Weight: For FP4057TX: Approx. 695gm

For FP4057TX-E: 715gm

For FP4057TN: 24VDC; 8W

For FP4057TX-E: 24VDC; 10W

Ethernet: For connecting to a PLC, programming of

HMI, a third party device or drive

(10/100Mbps)

o

Panel Mounting and Panel cut-out:

Tighten the mounting screws evenly to a torque between 0.6 and

0.7 Nm to maintain water and dust resistance. Make sure the
panel is not dirty and warped and that it is strong enough to hold
the unit.

Note: Maximum Panel thickness (On which unit is to be mounted)
should be 6.0mm (Tolerance: +0.00mm and -0.50mm).

Procedure to mount the unit:

FIGURE - 1 There are four (4) slots provided on the unit case to

mount the unit. Also a set of four (4) mounting hardware
is provided with each FP5 unit. (It is consist of single
cap nut, screw and clamp)

FIGURE - 2 Insert the clamp into the slot provided on the unit

case. hold the unit straight. Tighten the mounting
screws evenly to a torque between 0.6 and 0.7 Nm.

FIGURE - 3 Thus this mounting hardware will hold the unit with

the surface.

F1

F2

F3

F4

F5

F6

184.00

195.00

142.00

131.00

Gasket

Front Case

Mounting
Hardware

Back Case

Quick Start Manual Doc. No.: QS\FP5\0310; Ver.: 1.00C Renu Electronics Pvt. Ltd.; Pub.: 06/2011

System Components:

- FP4057Txx unit with LCD, Touch Screen and RTC

- Power Supply Connector

- Installation Kit: Gasket, Four Mounting hardware
(each mounting hardware set consists of single cap nut,
screw and clamp).

- *FlexiSoft Software Installer CD

*FlexiSoft: Please check the latest version each time.
Note: User should order PLC / programming cable separately.

WARNING:

WARNING: DO NOT REMOVE OR REPLACE WHILE
CIRCUIT IS LIVE UNLESS THE AREA IS KNOWN TO BE
FREE OF IGNITIBLE CONCENTRATIONS OF FLAMMABLE
SUBSTANCES.

This equipment is suitable for use in Class I, Division 2,
Groups A, B, C and D or non-hazardous locations only.

WARNING – EXPLOSION HAZARD – Do not disconnect
equipment unless power has been removed or the area is
known to be non-hazardous.

WARNING – EXPLOSION HAZARD - Substitution of
components may impair suitability for Class I, Division 2.

WARNING - CAUTION, Battery May Explode If Mistreated.
Do Not Recharge, Disassemble Or Dispose Of In Fire.

WARNING - Replace Battery With type CR1225FH-LF,
manufactured by Renata SA, only. Use of Another Battery
May Present A Risk Of Fire Or Explosion. See Owner's
Manual For Safety Instructions”

A recommendation for the user to periodically inspect the
sealed devices used, for any degradation of properties and
replace if degradation is found.

Figure - 1

Figure - 2

Figure - 3

RAM 256MB
Hard Disk 800MB (including 200MB for the .NET
Space Framework Redistributable)
Display 1024 x 768 High Color 16-bit
Mouse/ Required
Keyboard

(i) Insert the CD in the PC drive and follow the instructions given.

(ii) In case the software does not autoexecute, please run the
\DISK1\SETUP.EXE file from CD.

(iii) In case software has been downloaded from the Web site, first
Extract the software installation files, then run the Setup.exe file.

Getting Started:

User should follow the given sequence to configure and use any
Flexi Panel series unit:

1. Install FlexiSoft Software.

2. Create a PZM application using FlexiSoft software.

3. Connect programming cable.

4. Download Firmware i.e. driver for the PLC if PLC is
being used. FP unit cannot communicate with PLC till
the required driver is downloaded to the unit.

5. Download application.

6. Now FP unit is ready to use in the system.

Install the software:

The minimum system requirements for running the FlexiSoft
software are:
Processor 800MHz Pentium processor OR euivalent

processor
Operating Microsoft Windows 2000
System Microsoft Windows XP Professional / Home

Edition with SP2 / Vista

Technical Support

For Technical support please contact factory along with the unit
serial number and revision number written on the address sticker
of the unit. Also provide information of the PLC if used in
application.

Renu Electronics Pvt. Ltd.
Survey No. 2/6, Baner Road, Pune – 411 045.
Maharashtra, INDIA
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
Website: www.renuelectronics.com

MANUAL REVISIONS:
Rev. No. Doc. No. Date Description

1.00A QS\FP5\0310 21/12/10 Rated input voltage is
mentioned.

1.00B QS\FP5\0310 17/01/11 Wattage & weight of
the unit is updated.

1.00C QS\FP5\0310 28/06/11 Ethernet models added.

Cable Diagrams:
4 Wire RS422/RS485 Cable connections:

Cable Diagrams:
PC to unit programming cable:

Cable Diagrams:
2 Wire RS485 Cable connections:

Quick Start Manual Doc. No.: QS\FP5\0310; Ver.: 1.00C Renu Electronics Pvt. Ltd.; Pub.: 06/2011

Grounding:

The optimum method for grounding electronic equipment is to
ground it separately from other high-power systems, and to
ground more than one unit of electronic equipment with a single­point ground.
The grounding marked terminal (see below) is provided on the
unit.

Note: Do not use a ground that has an unstable impedance, such
as painted screws, or ground subject to vibration.

Port Details (COM1 and COM2):
Pin description of communication port for FP models is as follows: