AVI-X TRANSMITTER CODE READER
OPERATING INSTRUCTIONS
I. General
The CR-100 Code Reader is a device that is used to identify the codes assigned to Model
AVI-X Automatic Vehicle Identification transmitters. The three components of the Code
Reader are a hand-held control unit, a locating wand, and a telephone handset cord.
II. Indicators and Controls
i. Power Pushbutton
The red pushbutton on the control unit labeled POWER is used to activate the device.
ii. Battery Condition LEDs
The control unit has two LED indicators. The green LED indicator labeled GOOD
provides an indication of adequate battery voltage. The red LED indicator labeled BAD
indicates low battery voltage. If the red LED is illuminated, the nine volt battery inside
the unit should be replaced.
iii. AVI Code Display
The Code Reader incorporates a six character LED display that is used to provide an
indication of the code assigned to the AVI-X transmitter being read. The Code Reader is
capable of reading and displaying valid codes ranging from 0 to 19,683.
III. Operating Instructions
1. Ensure that the AVI-X transmitter you are trying to identify is active. It must be
properly connected to 12 volt DC power source.
2. The Code Reader comes with a nine volt battery that must be installed prior to use.
To install the battery, slide open the battery compartment cover on the back of the
control unit and connect the battery to the battery clip. Replace the battery
compartment cover. To check the battery condition, press and hold the POWER
button. If the green LED in the BATTERY CONDITION box labeled GOOD is
illuminated, the battery voltage is adequate. If the red LED labeled BAD is
illuminated, the battery voltage is low and the battery should be replaced.
3. Connect the locating wand to the control unit using the telephone handset cord.
4. To identify a coded AVI-X transmitter, position the loop on the end of the locating
wand below the transmitter. Press and hold the POWER pushbutton and read the
code on the LED display.
Reno A&E
4655 Aircenter Circle
Reno, NV 89502-5948 USA
Telephone: (775) 826-2020
Fax: (775) 826-9191
Website: www.renoae.com
E-mail: contact
@
renoae.com
MODEL CR-100
Model CR-100 Op Instr 2008 09 05 P/N 551-5010-00
2
CR-100 In Use
(Code 9841 Being Read)
AVI-X TRANSMITTER CODE READER
OPERATING INSTRUCTIONS
I. General
The CR-100 Code Reader is a device that is used to identify the codes assigned to Model
AVI-X Automatic Vehicle Identification transmitters. The three components of the Code
Reader are a hand-held control unit, a locating wand, and a telephone handset cord.
II. Indicators and Controls
i. Power Pushbutton
The red pushbutton on the control unit labeled POWER is used to activate the device.
ii. Battery Condition LEDs
The control unit has two LED indicators. The green LED indicator labeled GOOD
provides an indication of adequate battery voltage. The red LED indicator labeled BAD
indicates low battery voltage. If the red LED is illuminated, the nine volt battery inside
the unit should be replaced.
iii. AVI Code Display
The Code Reader incorporates a six character LED display that is used to provide an
indication of the code assigned to the AVI-X transmitter being read. The Code Reader is
capable of reading and displaying valid codes ranging from 0 to 19,683.
III. Operating Instructions
5. Ensure that the AVI-X transmitter you are trying to identify is active. It must be
properly connected to 12 volt DC power source.
6. The Code Reader comes with a nine volt battery that must be installed prior to use.
To install the battery, slide open the battery compartment cover on the back of the
control unit and connect the battery to the battery clip. Replace the battery
compartment cover. To check the battery condition, press and hold the POWER
button. If the green LED in the BATTERY CONDITION box labeled GOOD is
illuminated, the battery voltage is adequate. If the red LED labeled BAD is
illuminated, the battery voltage is low and the battery should be replaced.
7. Connect the locating wand to the control unit using the telephone handset cord.
To identify a coded AVI-X transmitter, position the loop on the end of the locating wand
below the transmitter. Press and hold the POWER pushbutton and read the code on the
LED display.
Reno A&E
4655 Aircenter Circle
Reno, NV 89502-5948 USA
Telephone: (775) 826-2020
Fax: (775) 826-9191
Website: www.renoae.com
E-mail: contact
@
renoae.com
MODEL CR-100
Model CR-100 Op Instr 2008 09 05 P/N 551-5010-00
2
CR-100 In Use
(Code 9841 Being Read)
Loading...