Renishaw ATS 40-800, EQ500 User Manual
Installation guide
ATS 40-800 Installation and User Guide
for EQ500 Gauge
www.renishaw.com/gauging
2
© 2018 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred to any other media or language, by any
means, without the prior written permission of Renishaw.
The publication of material within this document does not imply freedom from the patent rights of Renishaw plc.
Disclaimer
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT
AT THE DATE OF PUBLICATION BUT MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT.
RENISHAW EXCLUDES LIABILITY, HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT.
Trademarks
RENISHAW® and the probe emblem used in the RENISHAW logo are registered trademarks of Renishaw plc in the UK and
other countries.
apply innovation is a trademark of Renishaw plc.
All other brand names and product names used in this document are trade names, service marks, trademarks, or registered
trademarks of their respective owners.
Renishaw part no: H-6242-8502-02-A
Issued: 02.2019
Contents
1. Before you begin ..........................................................................................................................4
2. Safety and warnings.....................................................................................................................5
3. Product information ......................................................................................................................8
4. Hardware .....................................................................................................................................9
5. Product installation .....................................................................................................................10
6. Installation in Renishaw Enclosure ............................................................................................17
3
1. Before you begin
4
Changes to equipment
Renishaw reserves the right to change specifications without notice.
Warranty
Equipment requiring attention under warranty must be returned to our supplier. No claims will be considered where equipment
has been incorrectly installed or misused, or where repairs or adjustments have been attempted by unauthorised persons. Prior
consent must be obtained in instances where Renishaw equipment is to be substituted or omitted. Failure to comply with this
requirement will invalidate the warranty.
WEEE directive
The use of this symbol on Renishaw products and/or accompanying documentation indicates that the product
should not be mixed with general household waste upon disposal. It is the responsibility of the end user to
dispose of this product at a designated collection point for waste electrical and electronic equipment (WEEE)
to enable reuse or recycling. Correct disposal of this product will help to save valuable resources and prevent
potential negative effects on the environment. For more information, please contact your local waste disposal
service or Renishaw distributor.
FCC Information to user (USA only)
47 CFR Section 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
47 CFR Section 15.21
The user is cautioned that any changes or modifications not expressly approved by Renishaw plc or authorised
representative could void the user’s authority to operate the equipment.
REACH regulation
Information required by Article 33(1) of Regulation (EC) No. 1907/2006 (“REACH”) relating to products containing substances of
very high concern (SVHCs) is available at:
www.renishaw.com/REACH
2. Safety and warnings
!
Safety and warnings
Residual Risk Summary
1. There is a potential crushing hazard between the rear corners of the EQ500 fixture plate (C) and the front support legs (E)
of the EQ500.
2. There is a potential impact injury if a user stands in the area where the EQ-ATS extends to the out position.
3. The stop button mount (G) on the EQ500 is obscured when the EQ-ATS is fitted, therefore, the stop button must be moved
to an alternative accessible position.
5
Item Description
A Cylinder
B Control box
C Fixture plate (M6 and M8)*
D Support Leg
E Support Strut
F Base Plate
G Stop Button Mount
* M6 and M8 fixture plates are orderable seperately
D
E
B
C
F
A
G
Safety and
Warnings
6
1. There is a potential crushing hazard between the rear corners of the EQ500 fixture plate (C) and the front support
legs (E) of the EQ500.
2. There is a potential impact injury if a user stands in the area where the EQ-ATS extends to the out position.
Loading...