M3T-FLX-64NSA
Converter Board for Connecting FLX100 to 64-pin 0.8-mm-pitch QFP (64P6N-A)/LQFP (64P6U-A)
User’s Manual
z Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
z These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
z Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
z All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
z When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
z Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
z The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
z If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
z Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
z This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to p ractical use by performing
integration test, evaluation, or some experiment else.
z In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
z Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
z This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
CAUTION
Renesas Tools Homepage http://www.renesas.com/en/tools
Keep safety first in your circuit designs!
Notes regarding these materials
Precautions to be taken when using this product
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
Rev.1.00
April 1, 2004
REJ10J0428-0100Z
(1/4)
1. Outline
The M3T-FLX-64NSA is a converter board for connecting the
100-core flexible cable FLX100 to a foot pattern for 64-pin
0.8-mm-pitch QFP (64P6N-A) or LQFP (64P6U-A).
2. Package Components(See Figure 1)
(1) M3T-FLX-64NSA converter board............................. 1 pc.
(2) YQPACK064SA
(3) NQPACK064SA160
(made by Tokyo Eletech Corporation)
(made by Tokyo Eletech Corporation)
......... 1 pc.
. 1 pc.
(4) YQ-GUIDE ................................................................4 pcs.
(5) M3T-FLX-64NSA User's Manual (This manual)
3. Specifications
Table 1 Specifications
64P6N-A
(64-pin 0.8-mm-pitch QFP)
Applicable package
or
64P6U-A
(64-pin 0.8-mm-pitch LQFP)
Insertion/removal
iterations of connector
20 times guaranteed
4. Usage(See Figure 2)
The M3T-FLX-64NSA can be used for debugging and board
mounted evaluation in common by mounting the
NQPACK064SA160 on the target system.
(1) For debugging
Mount the NQPACK064SA160 and YQPACK064SA on
the foot pattern of the target system in that order. And
connect the probe of the emulation pod to the upper
connector of the M3T-FLX-64NSA. Then connect the
YQPACK064SA and the M3T-FLX-64NSA.
(2) For onboard evaluation
Mount an MCU with on-chip flash memory or one-time
PROM and the HQPACK064SA (for 64P6N-A, separately
available) or HQPACK064SA160 (for 64P6U-A,
separately available) in that order on the
NQPACK064SA160 on the target system.
Before using the M3T-FLX-64NSA, be sure to read "7.
Precautions" on page 4.
M3T-FLX-64NSA
YQ-GUIDE (x4)
YQPACK064SA
NQPACK064SA160
Figure 1 Package components of the M3T-FLX-64NSA
(1) Debugging
FLX100
M3T-FLX-64NSA
(2) Onboard evaluation
YQ-GUIDE (x4)
YQPACK064SA
NQPACK064SA160
64-pin0.8-mm-pitch
(64P6N-A, 64P6U-A)
foot pattern
●: No. 1 pin
Be sure to align the pins.
For 64P6N-A:
HQPACK064SA
(separately available)
For 64P6U-A:
HQPACK064SA160
(separately available)
MCU with on-chip
flash memory or
one-time PROM
Figure 2 Usage of the M3T-FLX-64NSA
(2/4)
5. Connection Procedure (See Figure 3)
The procedure for connecting the M3T-FLX-64NSA is shown
below.
(1) Mount the NQPACK064SA160 on the target board.
(2) Attach the YQPACK064SA on the NQPACK064SA160.
(3) Secure the four corners of the YQPACK064SA with the
YQ-GUIDE's.
FLX100
(5)
● Do not use the screws include d with the
YQPACK064SA for fixing the YQPACK064SA.
● The screwdriver included with the
NQPACK064SA160 is used for fixing the
HQPACK064SA or HQPACK064SA160. Do not use
if for fixing the YQ-GUIDE's.
(4) Attach the M3T-FLX-64NSA on the YQPACK064SA.
(5) Connect the probe of the emulation pod to the
M3T-FLX-64NSA.
M3T-FLX-64NSA
(4)
YQ-GUIDE (x4)
YQPACK064SA
NQPACK064SA160
64-pin 0.8-mm-pitch
(64P6N-A, 64P6U-A)
foot pattern
(2)
(1)
Use a slotted screwdriver.
(3)
●: No. 1 pin
Be sure to align the pins.
Figure 3 Connection procedure of the M3T-FLX-64NSA
6. External Dimensions and a Sample Foot Pattern
31.0
63
64
M3T-FLX-64NSA REV.A
1
2
J2 J1
140140
49
50
47
48
31.0
20 21 20 21
15
16
RENESAS
MADE IN JAPAN
17
18
Figure 4 External dimensions and a sample foot pattern of the M3T-FLX-64NSA
33
34
31
32
0
.
2
1
5
.
6
1
28.5
0.5
0.8
13.2
17.2
13.2
Unit: mm
17.2
(3/4)
7. Precautions
CAUTION
Caution to Be Taken for This Product:
z When connecting the YQPACK064SA, be sure to use the included YQ-GUIDE's.
z Do not use the screws included with the YQPACK064SA to fix it.
z The HQPACK which is used for on-board evaluation varies with the product package. Use the HQPACK064SA
(separately available) and HQPACK064SA160 (separately available) for 64P6N-A package and 64P6U-A package,
respectively.
IMPORTANT
Notes on This Product:
z We cannot accept any request for repair.
z For purchasing the NQPACK064SA160, YQPACK064SA, HQPACK064SA and HQPACK064SA160, contact the
following:
Daimaru Kogyo Ltd. http://www.daimarukogyo.co.jp/
Tokyo Eletech Corporation http://www.tetc.co.jp/e_tet.htm
z For inquiries about the product or the contents of this manual, contact your local distributor.
Renesas Tools Homepage http://www.renesas.com/en/tools
8. Correspondence of Connectors J1 and J2
Table 2 Correspondence of the connectors
Pin No. of
connector
J1-1 NC J1-21 NC J2-1 NC J2-21 NC
J1-2 NC J1-22 NC J2-2 NC J2-22 NC
J1-3 49 J1-23 33 J2-3 1 J2-23 17
J1-4 50 J1-24 34 J2-4 2 J2-24 18
J1-5 51 J1-25 35 J2-5 3 J2-25 19
J1-6 52 J1-26 36 J2-6 4 J2-26 20
J1-7 53 J1-27 37 J2-7 5 J2-27 21
J1-8 54 J1-28 38 J2-8 6 J2-28 22
J1-9 55 J1-29 39 J2-9 7 J2-29 23
J1-10 56 J1-30 40 J2-10 8 J2-30 24
J1-11 25 J1-31 41 J2-11 9 J2-31 57
J1-12 26 J1-32 42 J2-12 10 J2-32 58
J1-13 27 J1-33 43 J2-13 11 J2-33 59
J1-14 28 J1-34 44 J2-14 12 J2-34 60
J1-15 29 J1-35 45 J2-15 13 J2-35 61
J1-16 30 J1-36 46 J2-16 14 J2-36 62
J1-17 31 J1-37 47 J2-17 15 J2-37 63
J1-18 32 J1-38 48 J2-18 16 J2-38 64
J1-19 NC J1-39 NC J2-19 NC J2-39 NC
J1-20 NC J1-40 NC J2-20 NC J2-40 NC
(NC: No connection)
IC1
Pin No. of
connector
IC1
Pin No. of
connector
IC1
Pin No. of
connector
IC1
(4/4)
Loading...