Renesas M34551T2-MCU User Manual
M34551T2-MCU
MCU Board for PC4504 Emulator System
User's Manual
Rev.1.00
September 1, 2003
REJ10J0276-0100Z
MS-DOS is a registered trademark of Microsoft Corporation of the U.S.
IBM and AT are registered trademarks of International Business Machines Corporation of the U.S.
• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal
injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any
malfunction or mishap.
• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to
the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas
Technology Corporation, Renesas Solutions Corporation or a third party.
• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas
Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact
Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product distributor for the latest
product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or
typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage,
liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology
Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://www.renesas.com).
• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms,
please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and
products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or
other loss resulting from the information contained herein.
• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances
in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an
authorized Renesas Technology product distributor when considering the use of a product contained herein for any specific purposes,
such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce
in whole or in part these materials.
• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the
Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to
the export control laws and regulations of Japan and/or the country of destination is prohibited.
• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products
contained therein.
Keep safety first in your circuit designs!
Notes regarding these materials
• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
• Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall
under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in
Japan.
For inquiries about the contents of this document or product, fill in the text file the installer of the emulator debugger generates in the
following directory and email to your local distributor.
\SUPPORT\Product-name\SUPPORT.TXT
Renesas Tools Homepage http://www.renesas.com/en/tools
Precautions to be taken when using this product
( 2 / 40 )
Contents
Preface ....................................................................................................................................4
1. Precautions for Safety.........................................................................................................5
1.1 Safety Symbols and Meanings ..............................................................................5
2. Handling Precautions..........................................................................................................9
3. Contents of the M34551T2-MCU Package ......................................................................11
3.1 Things to Check When Unpacking .....................................................................11
3.2 Other Necessary Products ...................................................................................11
4. M34551T2-MCU..............................................................................................................13
4.1 Outline.................................................................................................................13
4.2 Specifications ......................................................................................................14
4.3 Description of Switches ......................................................................................15
4.4 Description of Connectors...................................................................................17
4.5 Connection to the Target System ........................................................................21
4.6 LED .....................................................................................................................23
5. Using as an Evaluation Board ..........................................................................................25
5.1 System Configuration..........................................................................................25
5.2 Mounting the EPROM ........................................................................................25
5.3 Mounting the Rubber Legs..................................................................................26
5.4 Switch Settings....................................................................................................27
5.5 Connection to the Target System ........................................................................27
5.6 Connection to the External Power Source ..........................................................27
5.7 Turning the Power On .........................................................................................27
6. Precautions to Be Taken When Debugging......................................................................29
6.1 Reset ....................................................................................................................29
6.2 System Clock ......................................................................................................29
6.3 Real-time Capability of Timer ............................................................................29
6.4 Watchdog Timer..................................................................................................30
6.5 Pullup Transistors................................................................................................30
6.6 Port I/O Timing ...................................................................................................30
6.7 Characteristics of I/O Ports .................................................................................31
6.8 Power-down Mode ..............................................................................................32
6.9 Program Execution (G, GB)................................................................................33
6.10 External Trigger ................................................................................................35
7. Connection Circuit Diagram.............................................................................................37
Appendix A ..........................................................................................................................38
( 3 / 40 )
Preface
This user's manual describes the specifications of the M34551T2-MCU emulator board for Renesas
4551 and 4555 groups of 4-bit single-chip microcomputers.
The M34551T2-MCU is the MCU board for the PC4504 emulator.
For the PC4504 emulator main unit and the M3T-PD45 emulator debugger, refer to their user's
manuals.
To use the product properly
Precautions for Safety
• In both this User's Manual and on the product itself, several icons are used to insure
proper handling of this product and also to prevent injuries to you or other persons,
or damage to your properties.
• The icons' graphic images and meanings are given in "Chapter 1. Precautions for
Safety". Be sure to read this chapter before using the product.
( 4 / 40 )
1. Precautions for Safety
In both the user's manual and on the product itself, several icons are used to insure proper handling
of this product and also to prevent injuries to you or other persons, or damage to your properties.
This chapter describes the precautions which should be taken in order to use this product safely and
properly. Be sure to read this chapter before using this product.
1.1 Safety Symbols and Meanings
WARNING
CAUTION
IMPORTANT
In addition to the three above, the following are also used as appropriate.
If the requirements shown in the "WARNING"
sentences are ignored, the equipment may
cause serious personal injury or death.
If the requirements shown in the "CAUTION"
sentences are ignored, the equipment may
malfunction.
It means important information on using this
product.
means WARNING or CAUTION.
Example: CAUTION AGAINST AN ELECTRIC SHOCK
means PROHIBITION.
Example: DISASSEMBLY PROHIBITED
means A FORCIBLE ACTION.
Example:
The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
( 5 / 40 )
WARNING
Warning for Installation:
• Do not set this product in water or areas of high humidity. Make sure that the main unit does not
get wet. Spilling water or some other liquid into the main unit can cause an unrepairable damage.
Warning for Use Environment:
• This equipment is to be used in an environment with a maximum ambient temperature of 35 °C.
Care should be taken that this temperature is not exceeded.
CAUTION
Cautions to be Taken for This Product:
• Do not disassemble or modify this product. Disassembling or modifying this product can cause
damage. Disassembling and modifying the product will void your warranty.
• Use caution when handling the main unit. Be careful not to apply a mechanical shock.
• Do not pull the emulator probe (100-pin half-pitch cable or 50-pin normal-pitch cable) to
disconnect from the emulator main unit.
•Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO
(meter-size) type screws. When replacing screws, use same type screws as equipped before.
( 6 / 40 )
IMPORTANT
Notes on Differences between Actual MCU and Emulator:
• Emulator operation differs from emulation of a mask MCU, as listed below. For details refer to
"Chapter 6. Precautions to be Taken When Debugging".
(1) Reset condition
(2) Initial values of internal resource data at power-on
(3) Internal RAM and ROM capacities, etc.
(4) Electrical characteristics
(5) Operation in the power-down mode
(6) Operation of the watchdog timer function
• Therefore, always be sure to evaluate your system with an evaluation MCU (onetime version).
Also, be sure to perform board-mounted evaluation with ES (Engineering Sample) version MCU
to make final confirmation of device operation before starting mask production.
Note on the Target System:
• The operating voltage of the M34551T2-MCU is +3.0 V or +5.0 V. Therefore the target's supply
voltage should be in the range of +3.0 V ±10 % or 5.0 V ±10 %.
Notes on Connecting the Target System:
• When connecting the emulator probe, be careful to the wrong connection.
•When connecting the emulator probe, be careful to the warp of the cable. The warp may cause
breaking the wire.
( 7 / 40 )
MEMO
( 8 / 40 )
2. Handling Precautions
When using the M34551T2-MCU board, pay attention to the following:
(1) About the emulator
To use the M34551T2-MCU board, you always need to install it on the PC4504 emulator main
unit.
(2) About the MCU board installation
Before installing (and removing) the MCU board, always be sure to power off the PC4504
emulator main unit and unplug its power cord from the outlet. For details on how to install and
remove the MCU board, see "Chapter 2. Set-up" in the PC4504 System User’s Manual.
(3) Emulator debugger
When using the M34551T2-MCU board to debug your program, you need to have the M3T-PD45
emulator debugger (sold separately). You need also the data file for 4551/4555 Group included
with M3T-PD45.
(4) Registers that can be operated from M3T-PD45
Table 2.1 lists the registers that can be operated from the M3T-PD45. The "O" in the table means
that the register can be operated; the "X" means that the register cannot be operated.
Table 2.1 Registers that can be operated from M3T-PD45
Register Reference Modification Register Reference Modification
PC O O W1 O O
CY O O W2 O O
AOOW3OO
BOOC1OO
XOOC2XO
YOOCROO
ZOOPU0 O O
DOORLC O O
EOOMROO
SP O X R1 X O
V1 O O L1 X O
V2 O O L2 X O
I1 O O
(5) About the system clock frequency
When setting both bit 3 and bit 0 in the MR clock control register to "0" (high-speed mode, system
clock = f(XIN)), the system clock frequency should be in the following ranges.
•VDD = 3.0 V: XIN ≤ 1.0 MHz
•VDD = 5.0 V: XIN ≤ 2.0 MHz
( 9 / 40 )
MEMO
( 10 / 40 )
3. Contents of the M34551T2-MCU Package
3.1 Things to Check When Unpacking
Table 3.1 shows the contents of the M34551T2-MCU package. When unpacking your M34551T2MCU package, check to see that all the following components are included.
Table 3.1 Contents of M34551T2-MCU
Item Product name Quantity
1 M34551T2-MCU*
2 100-wire half-pitch cable (40 cm) 1
3 50-wire normal-pitch cable (10 cm) 1
4 2-wire cable for external trigger signal (50 cm) 1
5 PCA4029 pitch converter board 1
6 M34551E8FP (MCU for replacement)*
7 OSC-2 oscillator circuit board (J1 connector mounted)*
8 Power code*
9 Rubber legs*
10 M34551T2-MCU English user's manual (this manual) 1
11 M34551T2-MCU Japanese user's manual 1
*1 "M34551T-MCU" is printed on the board.
*2 M34551T2-MCU is shipped from the factory with the M34555M4-002FP mounted as an
evaluation MCU. If using with the 4551 Group, replace the evaluation MCU with the M34551E8FP
(included).
*3 The M34551T2-MCU is equipped with the OSC-2 oscillator circuit board for 4.0 MHz when
shipped from the factory. The OSC-2 oscillator circuit board mounted with only J1 connector for
clock frequency alteration is included with the product.
*4 The power cable and rubber legs are used when using the M34551T2-MCU as an evaluation
board.
*5 Keep the packaging carton and cushion material of the M34551T2-MCU to transport it for repair
or for other purposes in the future.
*6 If you find any item missing or faulty, or any suggestion, contact your local distributor.
1
2
3
4
4
1
1
1
1
4
3.2 Other Necessary Products
To bring forward program development on the 4551/4555 Group, the products given below are
necessary in addition to those contained in the package above. Get them separately to be ready when
necessary.
(1) Emulator main unit: PC4504
(2) Emulator debugger: M3T-PD45
(3) Programming adapter: PCA7414 (for M34551E8FP)
* An evaluation MCU is not provided for 4555 Group.
( 11 / 40 )
MEMO
( 12 / 40 )
Loading...