Renesas M306H7T3-RPD-E User Manual

Page 1

To our customers,

Old Company Name in Catalogs and Other Documents

On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.

Renesas Electronics website: http://www.renesas.com

April 1 Renesas Electronics Corporation

Issued by: Renesas Electronics Corporation (http://www.renesas.com)

, 2010

Send any inquiries to http://www.renesas.com/inquiry

Page 2

Notice

1. All information included in this document is current as of the date this document is issued. Such information, however, is

subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.

2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights

of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others.

3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.

4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of

semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information.

5. When exporting the products or technology described in this document, you should comply with the applicable export control

laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations.

6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics

does not warrant that such informatio n is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.

7. Renesas Electronics products are classified according to the following three quality grades: “Standard”, “High Quality”, and

“Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise expressly specified in a Ren esas E lectronics data sheets or dat a books, etc.

“Standard”: Computers; office equipment; communications equipment; test and measurement equipment; audio and visual

equipment; home electron ic appliances; machine tools; personal electronic equipment; and industrial robots.

“High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-

crime systems; safety equipment; and medical equipment not specifically designed for life support.

“Specific”: Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or

systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other appl i cations or purposes that pose a d irect threat to human life.

8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics,

especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges.

9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have

specific characteristics such as t he occu rrence o f failure at a certai n rate an d malfunct io ns under cert ain u se con dition s. Further, Renesas Electronics prod ucts are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you.

10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental

compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.

11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas

Electronics.

12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this

document or Renesas Electronics products, or if you have any other inquiries.

(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation an d also includes its majority-

owned subsidiaries.

(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.

Page 3

User’s Manual

M306H7T3-RPD-E

User’s Manual

Emulation Pod for M16C/6H Group M306H7

Rev.1.00 2005.09

Page 4

Keep safety first in your circuit designs!

1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.

Notes regarding these materials

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.

2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of an third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.

3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contac Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributo for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http:/ www.renesas.com).

4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability o other loss resulting from the information contained herein.

5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.

6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.

7. If these products or technologies are subject to the Japanese export control restrictions, the must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.

ny diversion or reexport contrary to the export control laws and regulations of Japan and/ o

the country of destination is prohibited.

8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.

Page 5

M306H7T3-RPD-E User’s Manual Preface

Preface

The M306H7T3-RPD-E is an emulation pod for the M16C/6H Group M306H7 of 16-bit MCUs. It is used with a PC4701

emulator (excluding the PC4700L and PC4701L).

This user's manual mainly describes specifications of the M306H7T3-RPD-E emulation pod and how to setup it. For details on

the emulator main unit and emulator debugger, which are used with the M306H7T3-RPD-E, refer to each product's user's

manual or online manual.

All the components of this product are shown in "1.1 Package components" (page 13). If there is any question or doubt about

this product, contact your local distributor.

The related manuals for using this product are listed below. You can download the latest manuals from the Renesas Tools

homepage (http://www.renesas.com/en/tools).

Related manuals

Item Manual

Emulator main unit PC4701U User’s Manual PC4701M User’s Manual PC4701HS User’s Manual Integrated development environment High-performance Embedded Workshop User’s Manual

M16C PC4701 Emulator Debugger User’s Manual Emulator debugger M3T-PD30 User’s Manual

C compiler C compiler package for R8C/Tiny, M16C/60, 30, 20, 10 and Tiny Series

C Compiler User's Manual

Assembler C compiler package for R8C/Tiny, M16C/60, 30, 20, 10 and Tiny Series

Assembler User's Manual

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 3 of 88

Page 6

M306H7T3-RPD-E User’s Manual Important

Important

Before using this product, be sure to read this user’s manual carefully.

Keep this user’s manual, and refer to this when you have questions about this product.

Emulator:

The emulator in this document refers to the following products that are manufactured by Renesas Technology Corp.:

(1) PC4701 main unit

(2) Emulation pod

(3) Package converter board for connecting the user system

The emulator herein does not include the customer’s user system and host machine.

Purpose of use of the emulator:

This emulator is a device to support the development of a system that uses the M16C Family M16C/60 Series M16C/6H

Group/M306H7 of Renesas 16bit single-chip MCUs. It provides support for system development in both software and

hardware.

Be sure to use this emulator correctly according to said purpose of use. Please avoid using this emulator for other than its

intended purpose of use.

For those who use this emulator:

This emulator can only be used by those who have carefully read the user’s manual and know how to use it.

Use of this emulator requires the basic knowledge of electric circuits, logical circuits, and MCUs.

When using the emulator:

(1) This product is a development supporting unit for use in your program development and evaluation stages. In

mass-producing your program you have finished developing, be sure to make a judgment on your own risk that it can be

put to practical use by performing integration test, evaluation, or some experiment else.

(2) In no event shall Renesas Solutions Corp. be liable for any consequence arising from the use of this product.

(3) Renesas Solutions Corp. strives to renovate or provide a workaround for product malfunction at some charge or without

charge. However, this does not necessarily mean that Renesas Solutions Corp. guarantees the renovation or the provision

under any circumstances.

(4) This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore,

it does not fall under the application of Electrical Appliance and Material Safety Law and protection against

electromagnetic interference when used in Japan.

(5) Renesas Solutions Corp. cannot predict all possible situations or possible cases of misuse where a potential danger exists.

Therefore, the warnings written in this user’s manual and the warning labels attached to this emulator do not necessarily

cover all of such possible situations or cases. Please be sure to use this emulator correctly and safely on your own

responsibility.

(6) This product is not qualified under UL or other safety standards and IEC or other industry standards. This fact must be

taken into account when taking this product from Japan to some other country.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 4 of 88

Page 7

M306H7T3-RPD-E User’s Manual Important

Usage restrictions:

This emulator has been developed as a means of supporting system development by users. Therefore, do not use it as a device

used for equipment-embedded applications. Also, do not use it for developing the systems or equipment used for the following

purposes either:

(1) Transportation and vehicular

(2) Medical (equipment where human life is concerned)

(3) Aerospace

(4) Nuclear power control

(5) Undersea repeater

If you are considering the use of this emulator for one of the above purposes, please be sure to consult your local distributor.

About product changes:

We are constantly making efforts to improve the design and performance of this emulator. Therefore, the specification or

design of this emulator or its user’s manual may be changed without prior notice.

About the rights:

(1) We assume no responsibility for any damage or infringement on patent rights or any other rights arising from the use of

any information, products or circuits presented in this user’s manual.

(2) The information or data in this user’s manual does not implicitly or otherwise grant a license for patent rights or any other

rights belonging to us or third parties.

copied, duplicated or reproduced, in whole or part, without prior written consent of us.

About diagrams:

The diagrams in this user’s manual may not all represent exactly the actual object.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 5 of 88

Page 8

M306H7T3-RPD-E User’s Manual Precautions for Safety

Precautions for Safety

Definitions of Signal Words

In both the user’s manual and on the product itself, several icons are used to insure proper handling of this product and also to

prevent injuries to you or other persons, or damage to your properties.

This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read

this chapter before using this product.

This symbol represents a warning about safety. It is used to arouse caution about a potential danger that will possibly inflict an injury on persons. To avoid a possible

DANGER

injury or death, please be sure to observe the safety message that follows this symbol.

DANGER indicates an imminently dangerous situation that will cause death or heavy

wound unless it is avoided. However, there are no instances of such danger for the product presented in this user's manual.

WARNING

CAUTION

IMPORTANT

In addition to the five above, the following are also used as appropriate.

means WARNING or CAUTION.

Example:

WARNING indicates a potentially dangerous situation that will cause death or heavy

wound unless it is avoided.

CAUTION indicates a potentially dangerous situation that will cause a slight injury

or a medium-degree injury unless it is avoided.

CAUTION with no safety warning symbols attached indicates a potentially

dangerous situation that will cause property damage unless it is avoided.

This is used in operation procedures or explanatory descriptions to convey exceptional conditions or cautions to the user.

CAUTION AGAINST AN ELECTRIC SHOCK

means PROHIBITION.

Example:

DISASSEMBLY PROHIBITED

means A FORCIBLE ACTION.

Example:

UNPLUG THE POWER CABLE FROM THE RECEPTACLE.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 6 of 88

Page 9

M306H7T3-RPD-E User’s Manual Precautions for Safety

警告警告 WARNING

Warnings for AC Power Supply:

 If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it

forcibly. Failure to comply may cause electric shock and/or fire.

 Use an AC power cable which complies with the safety standard of the country.

 Do not touch the plug of the AC power cable when your hands are wet. This may cause electric shock.

 This product is connected signal ground with frame ground. If your developing product is transformless (not

having isolation transformer of AC power), this may cause electric shock. Also, this may give an unrepairable damage to this product and your developing one. While developing, connect AC power of the product to commercial power through isolation transformer in order to avoid these dangers.

 If other equipment is connected to the same branch circuit, care should be taken not to overload the circuit.

 When installing this equipment, insure that a reliable ground connection is maintained.

 If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect

power immediately by unplugging the AC power cable from the outlet. Do not use this as it is because of the danger of electric shock and/or fire. In this case, contact your local distributor.

 Before setting up this emulator and connecting it to other devices, turn off power or remove a power cable to

prevent injury or product damage.

Warnings to Be Taken for This Product:

 Do not disassemble or modify this product. Personal injury due to electric shock may occur if this product is

disassembled and modified. Disassembling and modifying the product will void your warranty.

 Make sure nothing falls into the cooling fan on the top panel, especially liquids, metal objects, or anything

combustible.

Warning for Installation:

 Do not set this product in water or areas of high humidity. Make sure that the product does not get wet. Spilling

water or some other liquid into the product may cause unrepairable damage.

Warning for Use Environment:

 This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care should be

taken that this temperature is not exceeded.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 7 of 88

Page 10

M306H7T3-RPD-E User’s Manual Precautions for Safety

注意注意 CAUTION

Cautions to Be Taken for Turning On the Power:

 Turn ON the power of the emulator and user system as simultaneously as possible. Turn OFF the power of the

emulator and user system as simultaneously as possible.

 Do not leave either the emulator or user system powered on, because of leakage current the internal circuits

may be damaged.

 When turning ON the power again after shutting OFF the power, wait about 10 seconds.

Cautions to Be Taken for Handling This Product:

 Use caution when handling the main unit. Be careful not to apply a mechanical shock.

 Do not touch the connector pins of the emulator main unit and the target MCU connector pins. Static electricity

may damage the internal circuits.

 Do not pull this emulator by the communications interface cable or the flexible cable for connecting the user

system. And, excessive flexing or force may break conductors.

 Do not flex the flexible cable (FLX120-RPD) for connecting to the emulator main unit and the flexible cable

(M3T-FLX160C) for connecting the user system excessively. The cable may cause a break.

 Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO (meter-size) type

screws. When replacing screws, use same type screws as equipped before.

Caution to Be Taken for System Malfunctions:

 If the emulator malfunctions because of interference like external noise, do the following to remedy the trouble.

(1) Press the RESET switch on the emulator front panel. (2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then reactivate

it.

Caution to Be Taken for External Trace Input Voltage:

 Assure that the external trace input voltage of emulator main body does not exceed the TTL level (5.0 V).

Otherwise, internal circuit may be damaged because of overload.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 8 of 88

Page 11

M306H7T3-RPD-E User’s Manual Contents

Page

Preface.........................................................................................................................................................................3

Related manuals..........................................................................................................................................................3

Important......................................................................................................................................................................4

Precautions for Safety .................................................................................................................................................6

Contents.......................................................................................................................................................................9

User Registration.......................................................................................................................................................11

Terminology................................................................................................................................................................12

1. Outline....................................................................................................................................................................13

1.1 Package Components..................................................................................................................................13

1.2 Other Tool Products Required for Development...........................................................................................14

1.3 System Configuration...................................................................................................................................15

1.3.1 System Configuration...........................................................................................................................15

1.3.2 Names and Functions of the PC4701 Front Panel LEDs....................................................................16

1.4 Specifications................................................................................................................................................18

1.5 Operating Environment.................................................................................................................................19

2. Setup......................................................................................................................................................................20

2.1 Flowchart of Starting Up the Emulator..........................................................................................................20

2.2 Installing the Emulator Debugger (M16C PC4701 Emulator Debugger)......................................................21

2.2.1 Installing the Emulator Debugger ........................................................................................................21

2.3 Connecting the Host Machine ......................................................................................................................22

2.4 Connecting the PC4701 ...............................................................................................................................23

2.4.1 Connecting the Cable to the PC4701..................................................................................................23

2.4.2 Connecting the FLX120-RPD to the Emulation Pod............................................................................24

2.4.3 PC4701 and Emulation Pod Arrangement...........................................................................................25

2.5 Turning ON the Power..................................................................................................................................26

2.5.1 Checking the Connections of the Emulator System............................................................................26

2.5.2 Turning ON/OFF the Power.................................................................................................................26

2.5.3 LED Display When the Emulator S tarts Up Normally..........................................................................27

2.6 Downloading Firmware.................................................................................................................................28

2.6.1 When It is Necessary to Download Firmware......................................................................................28

2.6.2 Downloading Firmware in Maintenance Mode.................................................................................

2.7 Self-check.....................................................................................................................................................29

2.7.1 Self-check Procedure...........................................................................................................................29

2.7.2 If an Error is Detected in the Self-check..............................................................................................30

2.8 Connecting the User System........................................................................................................................31

2.8.1 Connecting to a 100-pin LCC socket...................................................................................................32

2.8.2 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1).............................................................33

2.8.3 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2).............................................................34

2.8.4 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3).............................................................35

2.9 Changing Settings........................................................................................................................................36

2.9.1 Removing/Attaching the Upper Cover.................................................................................................36

2.9.2 Each Setting.........................................................................................................................................37

2.9.3 Selecting Clock Supply........................................................................................................................38

2.9.4 Switch Settings ....................................................................................................................................42

2.9.5 Installing and Removing Network Resistors for Pullup........................................................................ 45

2.9.6 Bypass Capacitors for A/D Converter..................................................................................................46

2.9.7 Connection Diagram of Data Slicer .....................................................................................................47

....28

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 9 of 88

Page 12

M306H7T3-RPD-E User’s Manual Contents

Page

3. Usage (How to Use the Emulator Debugger)........................................................................................................ 48

3.1. Making an MCU File....................................................................................................................................48

3.2 Setting the Work Area...................................................................................................................................48

3.3 Starting Up the Emulator Debugger.............................................................................................................49

3.3.1 Init Dialog Box......................................................................................................................................49

3.3.2 Checking Connections of the Emulator System ..................................................................................55

3.4 Downloading Program..................................................................................................................................56

3.5 Program execution .......................................................................................................................................57

3.6 Hardware Break............................................................................................................................................60

3.7 Trace Window...............................................................................................................................................64

3.8 RAM Monitor Window...................................................................................................................................68

4. Hardware Specifications........................................................................................................................................69

4.1 Target MCU Specifications...........................................................................................................................69

4.2 Differences between the Actual MCU and Emulator ....................................................................................70

4.3 Connection Diagram.....................................................................................................................................72

4.4 External Dimensions.....................................................................................................................................74

4.4.1 External Dimensions of the Emulation Pod .........................................................................................74

4.4.2 External Dimensions of the M30800T-PTC.........................................................................................75

4.5 Notes on Using This Product........................................................................................................................76

5. Troubleshooting.....................................................................................................................................................80

5.1 Flowchart to Remedy the Troubles...............................................................................................................80

5.2 When the Emulator Debugger Does Not Start Up Properly.........................................................................81

5.3 How to Request for Support.........................................................................................................................84

6. Maintenance and Guarantee.................................................................................................................................85

6.1 User Registration..........................................................................................................................................85

6.2 Maintenance.................................................................................................................................................85

6.3 Guarantee..................................................................................................................................................... 85

6.4 Repair Provisions..........................................................................................................................................85

6.5 How to Make Request for Repair .................................................................................................................86

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 10 of 88

Page 13

M306H7T3-RPD-E User’s Manual User Registration

User Registration

When you have purchased the emulator presented in this user's manual, please be sure to register it. As the H/W Tool Customer

Registration Sheet is included with this product, fill it in and FAX it to your local distributor or email the same contents to the

following address. Your registered information is used for only after-sale services, and not for any other purposes. Without user

registration, you will not be able to receive maintenance services such as a notification of field changes or trouble information.

So be sure to carry out the user registration.

For more information about user registration, please email to the following address.

regist_tool@renesas.com

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 11 of 88

Page 14

M306H7T3-RPD-E User’s Manual Terminology

Terminology

Some specific words used in this user's manual are defined as follows:

Emulator main unit (Hereafter PC4701)

This means a generic name for emulators for M16C, 7700, 740 Families. Take note of the fact that the M306H7T3-RPD-E (this product) does not support the PC4701L and PC4700L emulators. For details on specific models of PC4701, visit the Renesas Tools Homepage at http://www.renesas.com/en/tools.

Emulation pod

This means the emulation pod (this product) for the M16C/6H Group M306H7.

Emulator system

This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is configured with an emulator main unit, emulation pod, host machine and integrated development environment High-performance Embedded Workshop.

Integrated development environment High-performance Embedded Workshop

This tool provides powerful support for the development of embedded applications for Renesas microcomputers. It has an emulator debugger function allowing for the emulator PC4701 and emulation pod to be controlled from the host machine via an interface. Furthermore, it permits a range of operations from editing a project to building and debugging it to be performed within the same application. What’s more, it supports version management.

Emulator debugger (M16C PC4701 emulator debugger)

This means a software tool starting up from the High-performance Embedded Workshop to control the emulator and this product and enables debugging.

Firmware

Program that analyzes contents of communication with the emulator debugger and controls the emulator hardware. This program is installed in the flash memory in the emulator main unit. This program is downloadable from the emulator debugger to upgrade the firmware or to support other MCUs.

Host machine

This means a personal computer used to control the emulator main unit and emulation pod.

Software break

A software break is a function to break the program before the system executes an instruction at the specified address. The instruction at the preset address will not be executed.

Hardware break

A hardware break is a function to break the program when the system detects a write/read of data to/from memory or a leading/trailing edge of the signal entered from the external trace cable. The former break function is called address break; and the latter break function is called trigger break. While the instruction at the address where the software break is set is not executed, a hardware break is performed after the specified instruction is executed.

Target MCU

This means the MCU you are going to debug.

User system

This means a user’s application system using the microcomputer to be debugged.

User program

This means the program you are going to debug.

Evaluation MCU

This means the MCU mounted on the emulation pod which is operated in the specific mode for tools.

In this user’s manual, this symbol is used to show active Low. (e.g. RESET*: Reset signal)

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 12 of 88

Page 15

M306H7T3-RPD-E User’s Manual 1. Outline

1. Outline

This chapter describes the package components, the system configuration and the preparation for using this product for the first

time.

1.1 Package Components

The M306H7T3-RPD-E package consists of the following items. When unpacking it, check to see if your M306H7T3-RPD-E

contains all of these items.

Table 1.1 Package components

Item Quantity

M306H7T3-RPD-E emulation pod 1 FLX120-RPD flexible cable for connecting PC4701 1 M30800T-PTC converter board for 100-pin 0.65-mm-pitch LCC 1 IC61-1004-051 100-pin 0.65-mm-pitch LCC socket made by Yamaichi Electronics Co., Ltd. 1 OSC-3 16MHz oscillator circuit board for main clock (preinstalled) 1 OSC-2 oscillator circuit board (bare board) Network resistors for pulling up ports P0--P5 (51kΩ x 8) 6 H/W Tool Customer Registration Sheet (English) 1 H/W Tool Customer Registration Sheet (Japanese) 1 Repair request sheet (English) 1 Repair request sheet (Japanese) 1 M306H7T3-RPD-E User’s Manual (This manual) 1 M306H7T3-RPD-E User’s Manual (Japanese) 1 M306H7T3-RPD-E Supplementary Document (English) 1 M306H7T3-RPD-E Supplementary Document (Japanese) 1

* Please keep the M306H7T3-RPD-E's packing box and cushion material in your place for reuse at a later time when sending

your product for repair or other purposes. Always use these packing box and cushion material when transporting this

product.

* If there is any question or doubt about the packaged product, contact your local distributor.

* For purchasing the IC61-1004-051 or for technical information, contact Yamaichi Electronics Co., Ltd.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 13 of 88

Page 16

M306H7T3-RPD-E User’s Manual 1. Outline

1.2 Other Tool Products Required for Development

To bring forward programs development on the M16C/6H Group M306H7, the products listed below are necessary in addition to those contained package above. Get them separately.

Table 1.2 Other tool products required for development

Product Product name Notes

Emulator main unit PC4701 -

Emulator debugger

100-pin 0.65-mm-pit c h QF P

(PRQP0100JB-A)

Pitch converter board

* To purchase these products, contact your local distributor.

M16C PC4701 Emulator Debugger M3T-PD30

M3T-100LCC-DMS

M3T-DIRECT100S

M3T-100LCC-DMS

M3T-DUMMY100S M3T-100LCC-DMS

M3T-FLX-100NRB

Included with the PC4701

Required according to a foot

pattern of a user system

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 14 of 88

Page 17

M306H7T3-RPD-E User’s Manual 1. Outline

1.3 System Configuration

1.3.1 System Configuration

Figure 1.1 shows a configuration of the PC4701 system.

(6) Host machine

Interface cable

Host machine

(5) Emulator main unit

(2) Flexible cable connecting PC4701

(1) Emulation pod

(3) Flexible cable connecting user system

(4) Pitch converter board for connecting user system

(7) User system

Figure 1.1 System configuration

(1) Emulation pod M306H7T3-RPD-E (this product)

Emulation pod for the M16C/6H Group M306H7. This emulation pod contains an evaluation MCU.

(2) Flexible cable FLX120-RPD (included)

This is a 120-conductor flexible cable for connecting the PC4701 emulator and the emulation pod.

(3) Flexible cable M3T-FLX160C (included)

This is a 160 conductor flexible cable for connecting the emulation pod and the user system.

(4) Converter board M30800T-PTC (included)

This is a converter board for connecting to 100-pin 0.65-mm-pitch LCC socket IC61-1004-051 on the user system. For

details, refer to "2.8 Connecting the User System" (page 31).

(5) Emulator main unit PC4701

The emulator main unit for the M16C, 7700 and 740 families to be used with this product.

(6) Host machine

A personal computer to control the emulator.

(7) User system

This is your application system.

This emulator cannot supply the power to the user system. Therefore design your system so that the user system is

powered separately.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 15 of 88

Page 18

M306H7T3-RPD-E User’s Manual 1. Outline

1.3.2 Names and Functions of the PC4701 Front Panel LEDs

Figure 1.2 shows the names of the LEDs on the front panel of the emulator.

Target status LEDs

STATUS OF

TARGET

System status LEDs

POWER

SAFE

ERROR

STATUS OF

SYSTEM

RESET

PERFORMANCE

HIGH

EMULATOR

POWER

CLOCK

RESET

RUN

HALT

Figure 1.2 Names of the LEDs on the front panel of the PC4701

(1) System Status LEDs

The system status LEDs indicate the emulator PC4701's power supply, firmware operating status, etc. Table 1.3 lists the

definition of each system status LED.

Table 1.3 Definitions of the system status LEDs

Name Status Meaning

POWER

ON Emulator system power supply is turned ON.

OFF Emulator system power supply is turned OFF.

ON Emulator system is operating normally.

Special mode (maintenance mode) for downloading firmware. The

SAFE

Flashing

emulator system does not operate except for downloading firmware and the self-check.

OFF

Emulator system is not operating normally (system status error).

ON Emulator system is not operating normally.

ERROR

Flashing Downloading firmware.

ON Emulator system is operating normally.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 16 of 88

Page 19

M306H7T3-RPD-E User’s Manual 1. Outline

(2) Target Status LEDs

The target status LEDs indicate the target MCU's operating status and target board's power supply. Table 1.4 lists the definition

of each target status LED.

Table 1.4 Definitions of the target status LEDs

Name Status Meaning

POWER

CLOCK

RESET

RUN

HALT

ON Power is supplied to the user system.

OFF Power is not supplied to the user system.

ON Target MCU clock is oscillating.

OFF Target MCU clock is not oscillating.

ON Target MCU is being reset, or reset signal of the user system is held low.

OFF Target MCU is not being reset.

ON User program is being executed.

OFF User program has been halted.

ON CPU clock of target MCU is not oscillating.

OFF CPU clock of target MCU is oscillating.

Note on the Target Status POWER LED:

 If your MCU has two or more power supply terminals (Vcc), you need to supply power to all the

Note on the Target Status CLOCK LED:

terminals.

 If the LED is not turned on, check the following.

(1) After powering on the PC4701 (before starting up the emulator debugger): Make sure that the oscillator circuit board in the emulation pod is properly installed and it is

oscillating normally.

(2) After the emulator debugger is started up (after the Init dialog box settings are completed):

Make sure that the oscillator selected in the Init dialog box is oscillating normally.

IMPORTANT

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 17 of 88

Page 20

M306H7T3-RPD-E User’s Manual 1. Outline

1.4 Specifications

Tables 1.5 and 1.6 list the specifications of the M306H7T3-RPD-E.

Table 1.5 M306H7T3-RPD-E specifications (1/2)

Item Description

Applicable MCU M16C/6H Group M306H7 Usable MCU mode Single-chip mode Emulation Memory 1MB

VCC2=4.0V--5.5V, VCC1=3.0V--VCC2 (Xin: when operating without division)

Applicable power supply

Maximum operating frequency 16MHz

Clock supply

Basic debugging functions

Real-time trace function

Real-time RAM monitor function

Hardware break function 6 points (Bus detection, interrupt, external trace signal)

Execution time measurement function

C0 coverage 256KB Event output Break x1, Event x6 External trigger input TTL level x8

Host machine interface (see “2.3 Connecting the Host Machine” on page 22)

Power supply to emulator AC100--120V, AC200--240V (50/60Hz)

Overseas standards

*1 Available to connect the host machine that supports USB 2.0. With the USB interface, not all hardware (such as host

machine, USB devices, USB hub) combination will work and guaranteed.

VCC2=2.9V--5.5V, VCC1=2.9V--VCC2 (Xin: when operating in a divide-by-16 or 8-mode) VCC2=2.0V--5.5V, VCC1=2.0V--VCC2 (Xcin when operating)

VCC2=2.0V--2.6V operates only in low power dissipation mode.

XIN-X

CIN-XCOUT

OUT

Internal oscillator circuit board (OSC-3) Switchable to external oscillator input Internal oscillator circuit (fixed 32.768kHz) Switchable to external oscillator input

- Download

- Software break (max. 64 points)

- Program execution/stop (allows free-run execution supporting software breaks)

- Memory reference/setting (reference/setting C-variables, run-time execution)

- Register reference/setting

- Disassemble display

- C-level debugging, etc.

- 32K-cycle bus information recordable (Bus, external trigger, time stamp)

- 5 trace modes supported (Break/Before/About/After/Full)

- Can be recorded ON/OFF by events

- 1,024 bytes

- Data/last access result

Time between program start and stop Maximum/minimum/average execution time and pass count of specified four zones. Count clock: Equal to MCU Clock or 16 MHz

Dedicated parallel (PC4701HS) LPT parallel (PC4701M/PC4701U) Serial (PC4701HS/PC4701M) USB (USB 1.1, full-speed)*1 LAN (PC4701HS/PC4701U)

US EMI standard [FCC part15 Class A] CE marking [1998 Class A, EN55024: 1998]

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 18 of 88

Page 21

M306H7T3-RPD-E User’s Manual 1. Outline

Table 1.6 M306H7T3-RPD-E specifications (2/2)

Item Description

Connecting the user system (see “2.8 Connecting the User System” on page 31)

100-pin LCC socket 1 M30800T-PTC (included)

+ IC61-1004-051 (included) 100-pin 0.65-mm-pit c h QF P (PRQP0100JB-A)

1 M30800T-PTC (included) + M3T-100LCC-DMS (not included) + M3T- DIRECT100S (not included) 2 M30800T-PTC (included) + M3T-100LCC-DMS (not included) + M3T-DUMMY100S (not included) 3 M30800T-PTC (included) + M3T-100LCC-DMS (not included) + M3T-FLX-100NRB (not included)

1.5 Operating Environment

Be sure to use this emulator with the operating environmental of the emulator and host machine listed in Tables 1.7 and 1.8.

Table 1.7 Operating environmental conditions

Item Description

Operating temperature 5 to 35°C (no dew) Storage temperature -10 to 60°C (no dew)

Table 1.8 Operating environment of the host machine

Item Description

Host machine

CPU Pentium III 600 MHz or more recommended Memory 128 MB or more recommended Pointing device such as mouse Mouse or any other pointing device usable with the above OS that can be connected

CD drive Needed to install the emulator debugger or refer to the user’s manual

* Windows is trademarks of Microsoft Corporation in the United states and other countries.

IBM PC/AT compatibles Windows 98SE Windows Me Windows XP Windows 2000

to the main body of the host machine.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 19 of 88

Page 22

M306H7T3-RPD-E User’s Manual 2. Setup

2. Setup

This chapter describes the preparation for using this product, the procedure for starting up the emulator and how to change

settings.

2.1 Flowchart of Starting Up the Emulator

The procedure for starting up the emulator is shown in Figure 2.1. For details, refer to each section hereafter. And, when the

emulator does not start up normally, refer to “5. Troubleshooting” (page 80).

▼

Connect the emulation pod to the emulator.

▼

▼ Debug a program with various functions of

Figure 2.1 Flowchart of starting up the emulator

Check the package components. Refer to “1.1 Package Components” (page 13).

User registration Refer to “User Registration” (page 11).

Install the M16C PC4701 Emulator

Debugger.

Connect the host machine.

Connect the power supply for the emulator. Connect a power supply for the emulator.

Connect the user system. Connect the user system as occasion demands.

Turning on the power supply.

Check the LED display of the emulator.

Start up the emulator debugger from the

High-performance Embedded Workshop.

Set the operating environment

of the emulator debugger.

the emulator debugger

Install the M16C PC4701 Emulator Debugger.

Connect the PC4701 to the host machine with each interface connector. Set the interface selection switch on the rear panel of the PC4701 to the using interface.

Connect the emulation pod M306H7T3-RPD-E using the FLX120-RPD to the PC4701 (Be sure to see “2.4.3 PC4701 and Emulation Pod Arrangement” on page 25).

Turn ON the power to the emulator and the user system as simultaneously as possible.

Check that system status LED, and POWER, CLOCK, RESET and WARNING of target status LED are lighting. When the user system is not connected, the POWER LED does not light up.

Start up the High-performance Embedded Workshop, and the emulator debugger.

Set the INIT dialog box of the emulator debugger.

For how to use the High-performance Embedded Workshop and the emulator debugger, refer to each online manual.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 20 of 88

Page 23

M306H7T3-RPD-E User’s Manual 2. Setup

2.2 Installing the Emulator Debugger (M16C PC4701 Emulator Debugger)

If the OS used in your host machine is Windows XP or 2000, this installation must be executed by a user with administrator rights. Be aware that users without administrator rights cannot complete the installation.

Install the M16C PC4701 Emulator Debugger following the procedure described below.

2.2.1 Installing the Emulator Debugger

(1) Downloading the M16C PC4701 Emulator Debugger (as occasion demands) Download the latest M16C PC4701 Emulator Debugger from the URL below (free of charge). http://download.renesas.com/eng/mpumcu/upgrades/in_circuit_emulators/m16c/index.html

(2) Launching the installer Start the “setup.exe” program.

(3) Entering the user information In the “user information” dialog box, enter the user information (contractor, section, contact address, and host machine).

The supplied information will be turned into a format by which user regisration will be provided by e-mail.

(4) Completing the installation A dialog box will be displayed indicating that setup has been completed. It means that the installation you made is

completed.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 21 of 88

Page 24

M306H7T3-RPD-E User’s Manual 2. Setup

2.3 Connecting the Host Machine

When connecting the emulator PC4701 to a host machine, interface varies depending on the PC4701 used. Figure 2.1 shows

the outline to connect each interface cable. For details on interface, refer to each PC4701 user’s manual used.

Table 2.1 Operating environment of the host machine

PC4701 Interface Remarks

The special parallel interface cable is supplied with the PC4701HS. For connection with the dedicated parallel interface, the parallel interface printed circuit board (PCA4202G02: discontinued product) is required on the host machine side. The RS232C interface cable, 25-pin female/25-pin female conversion cable and 25-pin female/9-pin female conversion cable are supplied with the PC4701HS.

The RS232C interface cable and 25-pin female/9-pin male conversion cable are supplied with the PC4701M.

No LAN interface cable is supplied with the PC4701U; it is, therefore, necessary to arrange a LAN interface cable at your end.

PC4701HS

PC4701M

PC4701U

Dedicated parallel

Serial (RS232C)

LAN (10BASE-2/5) The LAN interface cable (10BASE-2/5) is supplied with the PC4701HS. LPT parallel The LPT parallel interface cable is supplied with the PC4701M.

Serial (RS232C)

LPT parallels The LPT parallel interface cable is supplied with the PC4701U. USB The USB interface cable is supplied with the PC4701U.

LAN (10BASE-T)

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 22 of 88

Page 25

M306H7T3-RPD-E User’s Manual 2. Setup

2.4 Connecting the PC4701

To connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable included with this product package.

Connect the PC4701 side connector of the FLX120-RPD to the cable connector of the PC4701, then secure with screws the

FLX120-RPD.

2.4.1 Connecting the Cable to the PC4701

Figure 2.2 shows how to connect the PC4701 and FLX120-RPD.

Emulator main unit

PC4701 side connector

of FLX120-RPD

UPSIDE should be face up.

Secure this screw.

Figure 2.2 Connecting the cable to the PC4701

CAUTION

Note on Connecting the PC4701 and FLX120-RPD:

 Always shut OFF power before connecting the cable. Otherwise, the internal circuits may be damaged.

IMPORTANT

Notes on Connecting the Cable and Securing the Screws:

 To connect the FLX120-RPD, be sure to hold the both sides of the PC4701 side connector horizontally

with the "UPSIDE" facing up.

 After connecting the cable to the emulator main unit PC4701, be sure to secure the screws mounted in

both sides of the connector.

Secure this screw.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 23 of 88

Page 26

M306H7T3-RPD-E User’s Manual 2. Setup

2.4.2 Connecting the FLX120-RPD to the Emulation Pod

Figure 2.3 shows how to connect the FLX120-RPD and the emulation pod.

Emulation pod

FLX120-RPD (Secure with the screws)

Figure 2.3 Connecting the FLX120-RPD to the emulation pod

CAUTION

Note on Connecting the Cable:

 Always shut OFF power before connecting the emulation pod and the FLX120-RPD. Otherwise, the

internal circuits may be damaged.

IMPORTANT

Note on Securing the Screws:

 After connecting the emulation pod and the FLX120-RPD, be sure to secure the screws mounted in both

sides of the connector cover

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 24 of 88

Page 27

M306H7T3-RPD-E User’s Manual 2. Setup

2.4.3 PC4701 and Emulation Pod Arrangement

The PC4701 and emulation pod should be laid out so that the FLX120-RPD becomes straight as shown in Fig. 2.4 below

(indicated by circle).

Under the condition in which the FLX120-RPD has warped and there arises clearance in the slit, it is impossible to comply

with the overseas applicable standards (U.S FCC and CE Marking) to be satisfied by this product.

Figure 2.4 PC4701 and Emulation Pod Arrangement

CAUTION

Note on PC4701 and Emulation Pod Arrangement:

 The PC4701 and emulation pod should be laid out in accordance with the explanation herein. In case

where these arrangements were carried out without following the explanation, it is impossible to keep the overseas applicable standards (U.S FCC and CE Marking) that this product must satisfy..

There arises clearance in the slit.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 25 of 88

Page 28

M306H7T3-RPD-E User’s Manual 2. Setup

2.5 Turning ON the Power

2.5.1 Checking the Connections of the Emulator System

Before turning the power ON, check the connection of the interface cable with host machine, PC4701, emulation pod, and user

system.

2.5.2 Turning ON/OFF the Power

 Turn ON the power of the emulator and user system as simultaneously as possible.

 Turn OFF the power of the emulator and user system as simultaneously as possible.

 Do not leave either the emulator or user system powered on, because of leakage current the internal circuits may be

damaged.

 When turning ON the power again after shutting OFF the power, wait for about 10 seconds.

IMPORTANT

Notes on Power Supply:

 The emulator's pin Vcc is connected to the user system in order to monitor user system voltage. For this reason,

the emulator cannot supply power to the user system. Therefore, provide the user system with a separate power supply from that of the emulator.

 Keep user system power supply voltage within the following range.

(1) When JP4 is set as FLX:

2.0 V ≤ Vcc2 ≤ 5.5 V

2.0 V ≤ Vcc1 < Vcc2

(2) When JP4 is set as INT:

2.0 V ≤ Vcc1 = Vcc2 ≤ 5.5 V

 Do not change user system power supply voltage after power has been activated.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 26 of 88

Page 29

M306H7T3-RPD-E User’s Manual 2. Setup

2.5.3 LED Display When the Emulator S tarts Up Normally

Figure 2.5 shows front panel LED lighting status when the emulator started up properly. Check it when starting up the

emulator system.

POWER

SAFE

ERROR

STATUS OF

SYSTEM

RESET

PERFORMANCE

HIGH

EMULATOR

STATUS OF

TARGET

POWER

CLOCK

RESET

RUN

HALT

This does not light when the user system is not connected.

: On

: Off

LED display when the emulator starts up normally

Figure 2.5 LED display when the power turned on

IMPORTANT

Note on the Target Status POWER LED:

Note on the Target Status CLOCK LED:

 If the MCU has two or more Vcc terminals, the LED does not light unless power is supplied to all the

terminals.

 If the LED is not turned on, check the following.

(1) After powering on the PC4701 (before starting up the emulator debugger): Make sure that the oscillator circuit board is properly installed in the PC4701 and it is oscillating

normally. (2) After the emulator debugger is started up (after the Init dialog box settings are complete): Make sure that the oscillator selected in the Init dialog box is oscillating normally.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 27 of 88

Page 30

M306H7T3-RPD-E User’s Manual 2. Setup

2.6 Downloading Firmware

2.6.1 When It is Necessary to Download Firmware

It is necessary to download the firmware in the cases listed below. Normally, the following are automatically detected when the

emulator debugger is started up, and the firmware is downloaded.

(1) you use this product for the first time

(2) the firmware has been upgraded

(3) the emulator debugger has been upgraded

(4) you use this product with a PC4701 which was used with other emulation pod before

If downloading firmware is not completed in the cases below, redownload the firmware.

- When the power is unexpectedly shut down during a download from the emulator debugger

- When a communications interface cable is unexpectedly pulled out

2.6.2 Downloading Firmware in Maintenance Mode

Download the firmware in maintenance mode as explained here following. The user system must not be connected when downloading the firmware.

(1) Set the interface select switch on the rear panel of the PC4701 to the dedicated parallel, LPT or serial interface to connect

the PC4701 and the host machine. Set the interface selection switch on the rear panel of the PC4701 according to the using

interface. The firmware may not be downloaded in maintenance mode correctly with the USB interface.

(2) Within 2 seconds of activating power to the emulator, press the RESET switch on the PC4701 upper panel to switch to

maintenance mode.

Switched to maintenance mode, the SAFE SYSTEM STATUS LED begins to flash.

(3) Start up the emulator debugger. When the Init dialog box setup is complete, the dialog which urges to download the

firmware will appear. Download the firmware following messages. Required time for downloading the firmware is about

60 seconds.

POWER

SAFE

ERROR

STATUS OF

SYSTEM

RESET

Immediately after turning on the power

POWER

CLOCK

RESET

RUN

HALT

All the LEDs light

POW ER

SAFE

ERROR

STATUS OF

SYSTEM

RESE T

When maintenance mode started

POW ER

CLOCK

RESET

RUN

HALT

SAFE LED lights

POWER

SAF E

ERROR

STATUS OF

SYST EM

RESET

When downloading firmware started

POWER

CLOCK

RESE T

RUN

HAL T

ERROR LED lights

POWER

SAFE

ERROR

STATUS OF

SYSTEM

RES ET

POWER

CLOCK

RESET

RUN

HALT

SAFE LED blinks All the LEDs light

POW ER

SAFE

ERROR

STATUS OF

SYSTEM

RESE T

POW ER

CLOCK

RESET

RUN

HALT

POWER

SAFE

ERROR

STATUSOF

SYSTEM

RESET

When download complete

POWER

CLOCK

RESET

RUN

HALT

: On : Off : Blinking

Figure 2.6 Downloading firmware in maintenance mode

IMPORTANT

Note on Downloading Firmware:

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 28 of 88

 Do not shut OFF power while the firmware is being downloaded. Doing so, the emulator will not start

up properly. If power is shut OFF by mistake, redownload the firmware in maintenance mode.

Page 31

M306H7T3-RPD-E User’s Manual 2. Setup

2.7 Self-check

2.7.1 Self-check Procedure

To run the self-check of the emulator, do so as explained here below. While the self-check is in progress, the LEDs will change

as shown in Figure 2.7.

(1) If the user system is connected, disconnect it.

(2) Set the switches in the emulation pod to the factory settings as shown in Figure 2.8.

(3) Within 2 seconds of activating power to the emulator, press the system reset switch on the emulator front panel to switch

the emulator to maintenance mode.

(4) Check the SAFE LED starts blinking and then press the system reset switch again.

(5) The self-check will start. If the normal result is displayed in about 30 seconds, the self-check has terminated normally.

POWER

SAFE

ERROR

STATUS OF

SYSTEM

RESE T

POWER

CLOCK

RESET

RUN

HALT

(1) All the LEDs light

Immediately after turning on the power

POW ER

SAFE

ERROR

STATUS OF

SYSTEM

RESET

Self-check

: On : Off

: Blinking

POWER

CLOCK

RESET

RUN

HAL T

(2) SAFE LED blinks

POWER

SAFE

ERROR

STATUS OF

RESET

POWER

SAFE

ERROR

STATUS OF

RESE T

POWER

SAFE

SYSTEM

POWER

CLOCK

RESET

RUN

HALT

Completed normally

POW ER

CLOCK

RESET

RUN

HAL T

ERROR LED lights

System status error

POWER

CLOCK

ERROR

STATUS OF

SYSTEM

RESET

Target status error

RESET

RUN

HAL T

SAFE and ERROR LED blink

Figure 2.7 LED display in the self-check procedure

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 29 of 88

Page 32

M306H7T3-RPD-E User’s Manual 2. Setup

FLX

JP3

INT

OPEN

SW1 SW2

P87

OPEN

FLX

JP1 JP2

INT

FLX

INT

JP4

Xcin

SW3

SW4

Xout

INT

P86/

Xcout

OPEN

SW5

VDD2 V50/TVDD

JP5

JC1_R

JP6

V50 TVDD

JP7

Figure 2.8 Switch settings for the self-check (factory-settings)

2.7.2 If an Error is Detected in the Self-check

If the self-check does not result normally (system status error or target status error in Figure 2.7), check the following.

 Whether the emulation pod and PC4701 are connected properly

 Whether the proper firmware has been downloaded

 Whether the switch settings of this product are the factory-settings

IMPORTANT

Notes on Self-check:

 Perform the self-check while not connecting the user system.  If the self-check does not result normally (excluding user system error), the emulation pod may be

damaged. Then contact your local distributor.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 30 of 88

Page 33

M306H7T3-RPD-E User’s Manual 2. Setup

2.8 Connecting the User System

Connect the emulation pod to the user system as shown in Figure 2.9.

Tip of emulation pod probe

M30800T-PTC

(included)

M3T-100LCC-DMS

(not included)

LCC socket

100-pin LCC

(included)

M3T-FLX100-T

(not included)

M3T-DIRECT100S

100-pin QFP

(not included)

●: No. 1 pin * These three products are available in one package.

M3T-DUMMY100S

100-pin QFP

(not included)

M3T-FLX100-R

(not included)

M3T-FLX-100NRB

100-pin QFP

(not included)

Figure 2.9 Connecting the user system

CAUTION

Note on Connecting the User System:

 Take care not to attach the converter board in a wrong direction. It may cause a fatal damage to the

emulator or user system.

* NQPACK, YQPACK, YQSOCKET, YQ-GUIDE, HQPACK, TQPACK and TQSOCKET are trademarks of Tokyo Eletech

Corporation.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 31 of 88

Page 34

M306H7T3-RPD-E User’s Manual 2. Setup

2.8.1 Connecting to a 100-pin LCC socket

Figure 2.10 shows how to connect a 100-pin LCC socket (IC61-1004-051 of Yamaichi Electronics Co., Ltd.) on the user

system to the M30800T-PTC (included).

(1) Attach the 100-pin LCC socket to the user system.

(2) Attach the CN2 side of the M30800T-PTC to the CN2 side of the FLX160-PRB.

(3) Attach the M30800T-PTC to the 100-pin LCC socket.

FLX160-PRB

Figure 2.10 Connecting to a 100-pin LCC socket

Note on Connecting the User System:

 Take care not to attach the converter board in a wrong direction. It may cause a fatal damage to the

emulator or user system.

(1)

(2)

CN2 side

M30800T-PTC

100-pin LCC socket

No.1 pin

CAUTION

User system

IMPORTANT

Notes on Connectors of Converter Boards:

 The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal iterations.  For purchasing the IC61-1004-051 or for technical information, contact Yamaichi Electronics Co., Ltd.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 32 of 88

Page 35

M306H7T3-RPD-E User’s Manual 2. Setup

2.8.2 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1)

Figure 2.11 shows how to connect a 100-pin 0.65-mm-pitch foot pattern on the user system to the M3T-DIRECT100S (not

included), and here following is its procedure.

For details on the M3T-100LCC-DMS (not included) and M3T- DIRECT100S (not included), refer to each user's manual.

(1) Attach the M3T- DIRECT100S to the user system.

(2) Attach the M3T-100LCC-DMS to the M3T-DIRECT100S.

(3) Attach the CN2 side of the M30800T-PTC to the CN2 side of the FLX160-PRB.

(4) Attach the M30800T-PTC to the M3T-100LCC-DMS

FLX160-PRB

CN2 side

(3)

M30800T-PTC

(4)

(2)

(PRQP0100JB-A) foot pattern

(1)

Figure 2.11 Connecting to a 100-pin 0.65-mm-pitch foot pattern (1/3)

CAUTION

Note on Connecting the User System:

 Take care not to attach the converter board in a wrong direction. It may cause a fatal damage to the

emulator or user system.

M3T-100LCC-DMS

(not inclueded)

M3T-DIRECT100S

(not inclueded)

100-pin 0.65-mm-pitch

No.1 pin

User system

IMPORTANT

Notes on Connectors of Converter Boards:

 The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal iterations.  The connectors of the M3T-100LCC-DMS and M3T-DIRECT100S are guaranteed for only 20

insertion/removal iterations.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 33 of 88

Page 36

M306H7T3-RPD-E User’s Manual 2. Setup

2.8.3 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2)

Figure 2.12 shows how to connect a 100-pin 0.65-mm-pitch foot pattern on the user system to the M3T-DUMMY100S (not

included), and here following is its procedure.

For details on the M3T-100LCC-DMS (not included) and M3T-DUMMY100S (not included), refer to each user's manual.

(1) Attach the M3T-DUMMY100S to the user system.

(2) Attach the M3T-100LCC-DMS to the M3T-DUMMY100S.

(3) Attach the CN2 side of the M30800T-PTC to the CN2 side of the FLX160-PRB.

(4) Attach the M30800T-PTC to the M3T-100LCC-DMS.

FLX160-PRB

CN2 side

(3)

M30800T-PTC

M3T-100LCC-DMS

(4)

(not included)

(2)

M3T-DUMMY100S

(not included)

100-pin 0.65-mm-pitc h (PRQP0100JB-A) foot pattern

(1)

No.1 pin

User system

Figure 2.12 Connecting to a 100-pin 0.65-mm-pitch foot pattern (2/3)

CAUTION

Note on Connecting the User System:

 Take care not to attach the converter board in a wrong direction. It may cause a fatal damage to the

emulator or user system.

On-board evaluation

FLASH MCU etc.

IMPORTANT

Notes on Connectors of Converter Boards:

 The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal iterations.  The connectors of the M3T-100LCC-DMS and M3T-DUMMY100S are guaranteed for only 20

insertion/removal iterations.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 34 of 88

Page 37

M306H7T3-RPD-E User’s Manual 2. Setup

2.8.4 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3)

Figure 2.13 shows how to connect a 100-pin 0.65-mm-pitch foot pattern on the user system to the M3T-FLX-100NRB (not

included), and here following is its procedure.

For details on the M3T-100LCC-DMS (not included) and M3T-FLX-100NRB (not included), refer to each user's manual.

(1) Attach the NQPACK100RB included with the M3T-FLX-100NRB to the user system. (2) Attach the YQPACK100RB included with M3T-FLX-100NRB to the NQPACK100RB and secure it with the

YQ-GUIDE's. (3) Attach the M3T-FLX-100NRB to the YQPACK100RB. (4) Attach the M3T-100LCC-DMS to the M3T-FLX-100NRB (5) Attach the CN2 side of the M30800T-PTC to the CN2 side of the FLX160-PRB. (6) Attach the M30800T-PTC to the M3T-100LCC-DMS.

FLX160-PRB

CN2 side

(5)

M30800T-PTC

M3T-100LCC-DMS

(6)

(not included)

M3T-FLX-100NRB

(not included)

(4)

(3)

YQ-GUIDE(x4)

These corners are not round.

* : These four products are available in one package.

YQPACK100RB

(2)

NQPACK100RB

100-pin 0.65-mm-pitch (PRQP0100JB-A) foot pattern

(1)

No.1 pin

User system

Figure 2.13 Connecting to a 100-pin 0.65-mm-pitch foot pattern (3/3)

On-board evaluation

HQPACK100RB168

(not included)

FLASH MCU etc

CAUTION

Note on Connecting the User System:

 Take care not to attach the converter board in a wrong direction. It may cause a fatal damage to the

emulator or user system.

IMPORTANT

Notes on Connectors of Converter Boards:

 The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal iterations.  The connectors of the M3T-100LCC-DMS and M3T-FLX-100NRB are guaranteed for only 20

insertion/removal iterations.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 35 of 88

Page 38

M306H7T3-RPD-E User’s Manual 2. Setup

2.9 Changing Settings

This chapter describes how to set the inside of the emulator.

2.9.1 Removing/Attaching the Upper Cover

(1) Removing the upper cover

To open the upper cover, remove the four screws of both sides of this product and lift off the upper cover (see Figure 2.14)

(2) Attaching he upper cover

To close the upper cover, attach the upper cover and secure the four screws of both sides of this product.

Figure 2.14 Removing the upper cover

CAUTION

Note on Removing and Attaching the Upper Cover:

 Always shut OFF power when removing/attaching the upper cover or changing the switch settings.

Otherwise the internal circuit may be damaged.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 36 of 88

Page 39

M306H7T3-RPD-E User’s Manual 2. Setup

2.9.2 Each Setting

Figure 2.15 shows the positions of each part of this product.

(3) Socket for mounting

network resister for pullup

(2) Switches

ADDAna

TVDD

M306H7T3-PRT REV.A

P87/Xcin

SW3

Xout

SW4

P86/Xcout

SW5

JP5 JP7

V50/

JP4 VCC1

JP2→CVIN1

JP4→SVREF

JP3→SYNCIN

(1) Oscillator circuit board

SW1

SW2

START CNVss

JP1JP2JP3

JC1_R

JP6

JP5→TEST3

JC1

(2) Switches

Common board (M30620T3-RPDC)

Figure 2.15 Positions of each part

MCU dependent board

(M306H7T3-PRT)

(4) Bypass capacitor for A/D converter

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 37 of 88

Page 40

M306H7T3-RPD-E User’s Manual 2. Setup

2.9.3 Selecting Clock Supply

(1) Clock Supply to the MCU

You can choose a clock supplied to the evaluation MCU by the Emulator tab in the Init dialog box of the emulator debugger.

Table 2.2 lists the factory-settings of each clock supply when you install the emulator debugger.

Table 2.2 Clock Supply to the MCU

Clock Display of emulator debugger Description Default setting

Main (XIN-XOUT)

Internal

External User system -

Internal oscillator circuit of emulation pod

(OSC-3: 16.0 MHz or OSC-2)

Ye s

Sub (XCIN-XCOUT)

Internal

External User system Yes

Internal oscillator circuit of emulation pod

(32.768 kHz)

IMPORTANT

Note on Changing the Clock Supply:

(2) Using the Internal Oscillator Circuit Board

An oscillator circuit board for 16.0 MHz (OSC-3) is mounted on this product. Also the oscillator circuit board (OSC-2) is

attached to change the oscillation frequency. When you use an internal oscillator circuit as a main clock, “Internal” can be set

by the emulator debugger.

 The clock supply can be set in the Init dialog box when starting up the emulator debugger or inputting

CLK command on the script window.

 For pins X

Switch Settings" (page 42)

CIN-XCOUT

, it is necessary to set the switches in the emulation pod. For details, refer to "2.9.4

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 38 of 88

Page 41

M306H7T3-RPD-E User’s Manual 2. Setup

(3) Replacing Oscillator Circuit Boards

Figure 2.16 shows how to replace the oscillator circuit boards. For the position of the oscillator circuit board, see Figure 2.15.

(1) Unscrew the screw securing the oscillator circuit

board.

(2) Lift off the oscillator circuit board.

(3) Insert the connector of a new oscillator circuit board

to the connector of the main board.

Figure 2.16 Replacing oscillator circuit boards

Note on Replacing the Oscillator Circuit Board:

 Always shut OFF power when removing the upper cover or replacing oscillator circuit board. Otherwise,

internal circuits may be damaged.

(4) Secure the new oscillator circuit board with the

screw.

CAUTION

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 39 of 88

Page 42

M306H7T3-RPD-E User’s Manual 2. Setup

(4) Changing the Internal Oscillator Circuit of the Emulation Pod

To use the emulation pod at a desired frequency, build the desired oscillator circuit on the included OSC-2 oscillator circuit

board (bare board). Figure 2.17 shows an external view of the OSC-2 oscillator circuit board (bare board) and where connector

pins are located. Figure 2.18 shows the circuitry of the OSC-2 oscillator circuit board (bare board). Use the number of

oscillator circuits recommended by the oscillator manufacturer.

J1-4:GND

J1-3:O s c illa tion output

J1-2:GND J1-1:VCC

Figure 2.17 External view of the OSC-2 oscillator circuit board and its connector pin positions

IC1

CLK

J1-3

* *

X1 ,X2

X1:5.08-mm- pitch 2- pin oscillator

X2:2.54-mm- pitch 2- pin oscillator

X3:2.54-mm- pitch 3- pin oscillator

IC1

IC1:Inverter (Unbuffer)

IC1

Vcc

GND

J1-1

J1-2

J1-4

Figure 2.18 Circuits of the OSC-2 oscillator circuit bare board

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 40 of 88

Page 43

M306H7T3-RPD-E User’s Manual 2. Setup

(5) Using the Oscillator Circuit on the User System

To operate this product with an external clock, construct the oscillator circuit as shown in Figure 2.19 in the user system and

input the oscillator output at 50% duty (within the operating range of the evaluation MCU) into pin X

. And pin X

OUT

should

be open. Choose "External" in the emulator debugger to use this clock.

Figure 2.19 External oscillator circuit

Make note that in the oscillator circuit shown in Figure 2.20 where a resonator is connected between pins X

and X

OUT

oscillation does not occur because a flexible cable, buffer IC and other devices are used between the evaluation MCU and the

user system. It is same for sub-clock oscillator circuits (X

CIN

and X

COUT

Figure 2.20 Circuit in which oscillation does not occur

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 41 of 88

Page 44

M306H7T3-RPD-E User’s Manual 2. Setup

2.9.4 Switch Settings

Here follows explanations of the switches of the emulation pod. Set the switches according to the user system.

Tables 2.3 and 2.4 list how to set toggle switches SW1 to SW5 of the M306H7T3-PRT board (MCU-dependent). Tables 2.5

and 2.6 list how to set jumper switches JP1 to JP7 on the M306H7T3-PRT (MCU-dependent board). For the positions of the

switches, see Figure 2.15.

(1) Toggle Switches SW1 to SW5 on the M306H7T3-PRT Board (MCU-dependent)

Table 2.3 Switch settings of the M306H7T3- PRT (1)

Signal Switch Setting Description

START SW1

(Factory-setting)

CNVSS SW2

OPEN

Xin-Xout is selected as an operation clock after releasing reset.

(Factory-setting)

Does not pull up/down pin START of the MCU.

Be sure to use this setting when the user system is connected.

OPEN

Xcin-Xcout is selected as an operation clock after releasing reset.

Pulls down pin CNVSS of the MCU with a resistance of 1 kΩ. Be sure to use this setting when the user system is not connected.

(Factory-setting)

Does not pull up/down pin CNVSS of the MCU.

Be sure to use this setting when the user system is connected.

OPEN

Do not use this setting.

P87/Xcin

SW3

P87

Xcin

P87

Xcin

When using the P87/Xcin of the MCU as a port P87 function

(Factory-setting)

When using the P87/Xcin of the MCU as a port Xcin function

OPEN

Does not connect pin Xout of the MCU to the user system.

Xout SW4

Xout

OPEN

Xout

Connects pin Xout of the MCU to the user system.

(Factory-setting)

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 42 of 88

Page 45

M306H7T3-RPD-E User’s Manual 2. Setup

Table 2.4 Switch settings of the M306H7T3- PRT (2)

Signal Switch Setting Description

P86/Xcout

SW5

P87 Xcout

Xcin

P87

Xcin

Connects pin P86/Xcout of the MCU to the user system.

(Factory-setting)

Does not connect pin P86/Xcout of the MCU to the user system.

CAUTION

Note on Switch Settings:

 Always shut OFF power before changing switch setting. Otherwise, internal circuit board may be

damaged.

IMPORTANT

Note on START and CNVSS Switch Settings:

(2) Jumper Switches JP1 to JP7 on the M306H7T3-PRT Board (MCU-dependent)

Table 2.5 Switch settings of the M306H7T3- PRT (3)

 Switch settings of the START and CNVSS are for debugging without the user system connected.

Signal Switch Setting of jumper switches

FLX FLX

SYNCIN

CVIN

JP1

Connects pin SYNCIN to internal circuit of the M306H7T3-PRT.

JP2

Connects pin CVIN to the user system via the M3T-FLX160C.

INT INT

Connects pin SYNCIN to the user system via the M3T-FLX160C.

FLX FLX

INT INT

Connects pin CVIN to the user system via the M3T-FLX160C.

FLX FLX

(Factory-setting)

VCCOFF JP3

Pin VCCOFF is to fixed to high..

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 43 of 88

INT INT

Connects pin VCCOFF to the user system via the M3T-FLX160C.

(Factory-setting)

Page 46

M306H7T3-RPD-E User’s Manual 2. Setup

Table 2.6 Switch settings of the M306H7T3- PRT (4)

Signal Switch Setting of jumper switches

FLX FLX

VCC1 JP4

Connects pin VCC1 of the MCU to the internal power supply of pod (equipotential of VCC2).

INT INT

Connects pin VCC1 of the MCU to

the user system. Be sure to use this

setting when the potentials of VCC1 and VCC2 are different.

(Factory-setting)

VDDAna JP5

JC1_R JP6

TVDD JP7

Note on Switch Settings:

 Always shut OFF power before changing switch setting. Otherwise, internal circuit board may be

damaged.

VDD2 V50/TVDD

Do not use this setting.

JC1_R JC1_R

Does not pull down video input signal

(RCA connector).

V50 TVDD

Do not use this setting.

CAUTION

VDD2

Be sure to use this setting.

(Factory-setting)

Pulls down video input signal (RCA connector) with a resistance of 75 Ω

(Factory-setting)

V50

Be sure to use this setting.

(Factory-setting)

V50/TVDD

TVDD

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 44 of 88

Page 47

M306H7T3-RPD-E User’s Manual 2. Setup

2.9.5 Installing and Removing Network Resistors for Pullup

In this product, you cannot control pullup for ports P0 to P5 by pullup control registers (pullup control register read/write are

possible).

A socket for installing the network resistor for pullup is mounted in this product. Mount the 51 kΩ network resistor supplied

with this product to the port for which pullup control is required. For the mounting location, refer to Figure 2.21 below. And

for the positions of each part, refer to Figure 2.15.

RM1

RM6

VCC

P5 P4 P3 P2 P1 P0

VCC

P07 P06 P05 P04 P03 P02 P01 P00

P17 P15P16 P14 P10P13 P12 P11

P27

P37

P47 P45P46 P44

P57 P55P56 P54

P25P26 P24

P35P36 P34

Figure 2.21 Position for mounting network resistors for pullup

P23 P22 P21

P33 P32 P31

P20

P30

P40P43 P42 P41

P50P53 P52 P51

CAUTION

Note on Installing and Removing Network Resistors for Pullup:

 Always shut OFF power before installing or removing network resistors for pullup. Also install

network resistors for pullup properly. Otherwise, internal circuit board may be damaged.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 45 of 88

Page 48

M306H7T3-RPD-E User’s Manual 2. Setup

2.9.6 Bypass Capacitors for A/D Converter

The M306H7T3-RPD-E has the M306H7T3-PRT board which has a foot pattern for installing bypass capacitors for A/D

converter near the MCU and premounted 0.1μF capacitors. Mount suitable bypass capacitors as occasion demands. Figure 2.15

shows where they are installed and Figure 2.22 shows their connection.

IC8

AVSS

M306H7FG-TOOL

AVCC

Figure 2.22 Foot patterns of bypass capacitors for A/D converter

IMPORTANT

Note on the A/D Converter Function:

 Because a flexible cable and other devices are used between the evaluation MCU and the user system,

the A/D converter operates differently from that of the actual MCU. Make the final evaluation of the A/D converter with the actual MCU.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 46 of 88

Page 49

M306H7T3-RPD-E User’s Manual 2. Setup

2.9.7 Connection Diagram of Data Slicer

This product has on-board sockets to change parts used for circuits connected to a data slicer. The circuit and the arrangement

of the parts used for each circuit are shown in Figure 2.23 and Figure 2.24, respectively.

Resistance and capacity

Factory-settings

R5 R6

R8 R10 R11

470Ω 39kΩ

22kΩ R12 R13

C8 C9

10kΩ

47pF

0.1μF C10 C11 C12

0.1μF

560pF C14 C15

2kΩ 2kΩ

470Ω

75Ω

47pF

47μF 47μF

SYNCIN

PER-E

CVIN

LP3 LP4

103 112 108 109

C10

User system

C12

VDDAna

R13

C14

VR1

VDDAna

R10

C15

R11

JC1

JP6

R12

TP4TP6

JP2

JP1

C11

Figure 2.23 Connection diagram of circuits connected to the data slicer

Figure 2.24 Arrangement of the parts used for each circuit

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 47 of 88

Page 50

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3. Usage (How to Use the Emulator Debugger)

This chapter describes how to start up the M16C PC4701 emulator debugger from the High-performance Embedded Workshop

and how to use the main windows.

3.1. Making an MCU File

It is necessary to make an MCU file to use this product with the emulator debugger. According to the MCU you use, change

the contents of the MCU file. Make the MCU file named “M306H7T3.MCU” etc. following the description below using a text

editor and store it in the "mcufiles" folder in the directory where the emulator debugger is installed.

The emulator debugger has been installed in the following directory by default.

- When using the M16C PC4701 emulator debugger on the High-performance Embedded Workshop

C:\Program Files\Renesas\He w\ Tools\Renesas\DebugComp\Platform\PDTarget\PD30\McuFiles

- When using the M3T-PD30

C:\mtool\PD30\McuFiles

The MCU file contains information such as, SFR area, internal RAM area, internal ROM area, firmware file name. The

contents of the MCU file when using the M306H7FGFP (8KB RAM, 256KB ROM) are as follows:

0 : SFR area Start address 3FF : End address 400 : Internal RAM Start address 23FF : End address C0000 : Internal ROM Start address FFFFF : End address M30620P : Name of firmware (Do not change.) 0 : Expansion No. (Do not change.)

3.2 Setting the Work Area

With this product, the emulator uses 54 bytes as a work area in emulation memory. With this product, set the work area address

at 10000h.

The area used as a work area (54 bytes) is specified in the Work Area tab of the INIT dialog box of the emulator debugger. And

be sure to set the MAP setting of the specified work area (54 bytes of 10000h to 10036h) as MAP=INT.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 48 of 88

Page 51

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.3 Starting Up the Emulator Debugger

When debugging the completed programs, switch the session. The session can be changed by the drop down list of the tool bar

shown below.

You will have as many sessions created as the number of targets you selected when creating a project, so select the session that

corresponds to the target to be connected from the drop-down list. Select “SessionM16C_PC4701_Emulator”

3.3.1 Init Dialog Box

After specifying the session, an Init dialog box to connect the target is displayed.

The Init dialog box is used to set the items that need to be set when the emulator debugger starts up. The contents set in this

dialog box remain effective the next time you start the debugger.

(1) MCU tab

1) Specifying the MCU file

Specifying the MCU file

Specify the MCU file for the target MCU.

(1) Click the “Refer…” Button”.

(2) ”Select MCU File” dialog box will be displayed. Specify the MCU file

for the target MCU.

- The MCU file contains the information specific to the target MCU.

- The specified MCU file is displayed at the MCU area field of MCU tab.

Look in:

File name: File of type:

Cancel Help

Open

Cancel

Cancel Help

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 49 of 88

Page 52

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

2) Specifying the communication interface

Specifying the communication interface (Parallel communication)

- In case where the parallel communication is set up, click the radio button

“Parallel” of MCU tab.

- For the host area, only IBM-PC/AT can be designated.

- Set the I/O address value that was set up with the special interface board

PCA4202G02 to the I/O address area.

- Input the I/O address in hexadecimal

- For I/O address setting of PCA4202G02, refer to the “PCA4202G02

Instruction Manual”.

Cancel Help

Specifying the communication interface (Serial communication)

- For connection with serial communication, click the radio button “Serial”

of MCU tab.

- Specify the communication port of serial interface used to the port area

and the baud rate to the baud rate area.

Cancel Help

Specifying the communication interface (LAN communication)

- For selecting the LAN communication, click the radio button “LAN” of

the MCU tab.。

- Specify the IP address of the emulator to the IP address area.

- Specify the IP address of the emulator at the IP address area. Specify the

IP address by one byte of decimal number separating each four bytes with

a period.

- Specify the port number at the Port area.

Cancel Help

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 50 of 88

Page 53

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

Specifying the communication interface (LPT communication)

- For selecting the LPT communication, click the radio button “LPT” of the

MCU tab.

- For the Type area, specify the LPT interface communication mode to be

used.

- Specify the I/O address of the parallel port at the I/O address area.

- For BIOS setup, the following addresses are available.

- 378h

- 278h

Cancel Help

Specifying the communication interface (USB communication)

- For selecting the USB communication, click the radio button “USB” of

the MCU tab

- The emulators connected by USB cable are shown at Serial No. area.

Select the serial No. of the emulator you are going to connect.

- Select the serial No. of the emulator you are going to connect.

Cancel Help

3) Executing the self-check

Cancel Help

Executing the self-check

Enable this function when you want the emulator to be self-checked at

startup. Be sure to select the check box only when you want the emulator to

be self-checked at startup.

Note:

In case where self-checking was normally completed, terminate the emulator debugger once, then start operation with no self-checking carried out again (with leaving the check box unchecked).

This function may be enabled in the following cases:

- When you are using the emulator you have just purchased, and fail to

download the firmware.

- When you successfully download the firmware, but fail to start up the emulator

- When you want to confirm whether the emulator is operating normally

because, for example, the MCU runs out of control or something is wrong

with the trace results

This function can be enabled only when you are starting up the emulator

debugger.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 51 of 88

Page 54

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

4) Specifying the clock frequency

Specifying the clock frequ ency

Specify the target MCU operation clock and clock dividing ratio.

- Specify the operation clock and clock dividing ratio.

- In case where no value was set up in the area in which the operation clock

is Specified, the unit operates with the reference clock (16 MHz) inside

the emulator (PC4701) as time measurement resource.

- In case where no value was set up in the area in which the dividing ratio is

Specified, the unit operates as “No dividing”. (Same as when “1” was

Specified.)

Cancel Help

(2) Debugging Information tab

Referencing the compiler used and the object format

Reference the compiler you are using and the format of the object file output

by the compiler.

To make this setting, use the dialog box that is brought up by selecting

[Debug] and then [Debug Settings...] from the menu.

Specifying the method for stori ng debug information

There are two methods for storing debug information: on memory method

and an on demand method.

Select the compiler you are using.

(By default, the on memory is selected)

When selecting the on demand method, check the [On Demand] check box.

Cancel Help

 On Memory

The debug information is stored in the memory of your computer. This

method is suitable when the size of the load module (user program) is

small.

 On Demand

The debug information is saved to a reusable temporary file. When you

download the same load module for a second time on, the saved debug

information will be reused and the load module can therefore be

downloaded fast. This method is suitable when the size of the load module

(user program) is large.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 52 of 88

Page 55

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(3) Work area tab

1) Specifying the firmware

Specifying the firmware file

For the radio button of the firmware group box, be sure to click “Default”.

Specifying the work a rea

Specifies the top address which is used as a work area at the start address

area of the work area group box.

- With the M306H7T3-RPD-E, set the work area address at 10000h.

- The top address of the work area is set to 2C00h by default.

Cancel Help

(4) Memory space expansion tab

Specifying the memory space expansion mode

Because the M306H7T3-RPD-E supports single-chip mode, only the radio

button “Normal” can be selected.

(5) Clock tab

Cancel Help

Specifying the target clock

Specify the clock sources supplied to the MCU (main clock and sub clock).

Select the appropriate clock sources according to the clock used by your

target MCU.

 Internal

Emulator’s internal clock

 External

User system clock

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 53 of 88

Page 56

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(6) Script tab

Automatically executing a script command

To automatically execute a script command when starting up the

debugger, click the “Refer...” button and specify the script file to

be executed.

Clicking the “Refer...” button brings up a file selection dialog box.

The script file you have selected is displayed in the Init File:

section of the dialog box shown here. If you do not want to

automatically execute a script command, delete the character

string displayed in the Init File: section of the dialog box.

What you specify here is reflected at only startup. If you specify

back again in the Init dialog box after startup, whatever you specified has no effect (restart the emulator debugger).

Cancel Help

When the tab settings (1) to (6) above are completed, click OK button.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 54 of 88

Page 57

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.3.2 Checking Connections of the Emulator System

Check to see that the emulator debugger has been connected correctly to the emulator.

Checking connections of the emulator system

When the emulator debugger is connected correctly to the emulator after you

have finished setting up the Init dialog box and the MCU Setting dialog box,

you will see a message “Connected” displayed on the “Debug” tab of the

Output window.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 55 of 88

Page 58

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.4 Downloading Program

Download the user program to be debugged.

1) Downloading from the work space window

Downloading the program

Download the object program you want to debug.

Select Download from “xxx.x30” of “Download module”.

Or you can select “Download” from the “Debug” menu for the same effect.

2) Showing the source program

Editor (Source) window

The editor (source) window is a window that always shows the content

of the source file corresponding to the current position of the program

counter (hereafter, PC).

The position of the PC at which the user program has stopped is

marked by a yellow arrow.

The operation up to the cursor position can be executed, and the software break point can be set up and reset, etc.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 56 of 88

Page 59

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.5 Program execution

(1) Program execution

CPU reset

Resets the target MCU.

Runs the program beginning with the current PC position.

Reset Go

Runs the program after resetting the target MCU.

Step In

Single-steps the program executing each statement (including those in functions).

Step Over

Single-steps the program executing each function call as one step.

Step Out

Exists a function and stops at a statement in the program next to the one that called the function.

STOP

Stops the program.

Go Free

Runs the program beginning with the current PC position. The software and hardware breaks set in it are temporarily ignored.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 57 of 88

Page 60

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(2) Software break

1) Setting the software break point

Execution setup procedure with software break:

(1) By double-clicking the break point setting line on the software

break point setting column in the editor (source) window, the

break point can be set up and released. (In this case, the red circle

is displayed on the setting line as shown in the window on the

left.)

2) Execution completed with software break

(2)

The cursor stops in the position where the software break was set up.

The statement in which the software break was set up is not executed.

Click the execution button.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 58 of 88

Page 61

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(3) Executing up to the cursor position (Come command)

1) Specifying the Come command

Setup procedure for executing COME command

(1) Click the line in the editor (source) window at which you want

the program to execute.

2) After the Come command has finished

(2)

The cursor stops in the position where the come command was executed.

The statement specified with the come command is not executed.

Click the Come button.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 59 of 88

Page 62

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.6 Hardware Break

Hardware break is set by event condition such as FETCH or DATA ACCESS, etc. The program stops after executing the

instruction at the set breakpoint (after several cycles).

(1) Break event setup dialog box

1) Opening the hardware break point setup dialog box

Hardware Break Point

Clicking this button opens the hardware break point setup dialog box.

2) Hardware Break Point Setting Window in initial state

Hardware break point Setting Window in initial state

Select the “Enable H/W Break” check box, and this break function will be

enabled, allowing you to set hardware break points.

Setting Break Event

Click the event line at which you want set a break event.

3) Break event setting dialog box

Specifying the event type

Click to select the event type you want to set.

- FETCH

Detects an instruction prefetch.

- DATA ACCESS

Detects a memory access.

- BIT ACCESS

Detects a bit access.

- INTERRUPT

Detects an occurrence of interruption or interrupt completion.

- TRIGGER

Detects a signal from the external trace signal input cable.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 60 of 88

Page 63

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(2) When FETCH is selected

1) Window for setting addresses

Setting the address

You can set eight conditions, e.g., a specified address, a specified address

range, etc. When you have finished setting the address, click OK.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 61 of 88

Page 64

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(3) When DATA ACCESS is selected

1) Window for setting the address

Setting the address

Sets the address by “Address” tab.

You can set eight conditions, e.g., a specified address, a specified address

range, etc.

2) Window for setting data

Setting data

Sets the address by “Data” tab.

You can set eight conditions, e.g., specified data, specified data range, etc.

Setting the access condition

You can set three conditions, e.g., read, write, and read/write. When you have

finished setting the data and access condition, click OK.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 62 of 88

Page 65

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3) Example Data Settings

Setting events for wordwise accesses to the even-addresses

STE.W A0,20E8h(A0=5423h)

High-order and low-order data effective

Setting a break event

A1 Address 1 :0020E8 Data 1 :5423 MASK :FFFF

Access :WRITE

Setting events for wordwise accesses to the odd-addresses

STE.W A0,20E5h(A0=AB79h)

Odd-address high-order data effective Even-address high-order data effective

Setting a break event (using 2 events)

A1 A2 Address 1 :0020E5 Address 1 :0020E6 Data 1 :7900 Data 1 :00AB MASK :FF00 MASK :00FF Access :WRITE Access :WRITE Set the combinatorial events to AND.

Setting events for wordwise accesses to the even-addresses

STE.B R0L,[A1A0](R0L=E5h,A1=0000h,A0=20E2h)

Low-order data effective

Setting a break event

A1 Address 1 :0020E2 Data 1 :00E5

MASK :00FF

Access :WRITE

Setting events for wordwise accesses to the odd-addresses

STE.B R0L,[A1A0](R0L=E6h,A1=0000h,A0=20E3h)

High-order data effective

Setting a break event

A1 Address 1 :0020E3 Data 1 :E600 MASK :FF00 Access :WRITE

(4) Setting the combinatorial event condition for the hardware break point

1) Window for setting the combinatorial event condition

Setting the combinatorial event condition

There are following four conditions that you can choose for the

combinatorial events.

- AND

The program breaks when all of the specified events occur.

- AND (Same Time)

The program breaks when the specified events occur at the same

time.

- OR

The program breaks when one of the specified events occurs.

- STATE TRANSITION

The program breaks when the state transition diagram goes into

the break state.

For each event, a pass count (number of passing) is specifiable

(1--255). When “AND” (same time) is specified for Combination,

you can not specify the pass count (fixed to one).

When you have finished setting the combinatorial event condition,

click the “Set” button.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 63 of 88

Page 66

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.7 Trace Window

The trace window is used to show the results of real-time trace measurements.

(1) Trace window

1) Opening the hardware break point setup dialog box

2) Trace window

Trace window

Clicking this button opens the trace window.

Trace window

The trace window is used to show the results of real-time trace

measurements. It has the following four display modes:

- Bus mode

Bus information per cycle can be inspected. The contents are

displayed in order of execution paths.

- Disassemble mode

The execution paths of the executed instructions can be

inspected. The contents are displayed in order of execution

paths.

- Data access mode

Data read/write cycles can be inspected

- Source mode

The execution paths of the source program can be inspected.

The trace window shows the measurement result when a real-time

trace measurement has finished. The trace window remains blank

until the real-time trace measurement in progress finishes.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 64 of 88

Page 67

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3) Trace Window (Bus mode display)

Explanation of the trace window (bus display)

Shows the status of the address bus.

- Address

Shows the status of the address bus.

- Data

Shows the status of the data bus.

- BUS

Shows the width of the external data bus. In the present

emulator, only “16b” for 16 bits wide bus is displayed.

- BHE*

Shows the status (0 or 1) of the BHE (Byte High Enable) signal.

If this signal = 0, the odd-address data is valid.

- BIU

Shows the status between the BIU (Bus Interface Unit) and

memory or I/O.

4) Trace Window (Disassemble mode display)

5) Trace Window (Source mode display)

6) Trace Window (Data access mode display)

Symbol Status

- : No change (non-active)

DMA : Data access except for CPU

INT : Interrupt acknowledge cycle

IB : Instruction code read (bytes) by CPU

DB : Data access (bytes) by CPU

IW : Instruction code read (words) by CPU

DW : Data access (words) by CPU

- R/W

Shows the status of the data bus. Displayed as “R” for Read,

“W” for Write, and “-” for no access.

- RWT

This is the signal to indicate a valid bus cycle. When valid,

RWT = 0. The Address, Data, and the BIU signals are effective

when this signal is 0.

- CPU

Shows the status between the CPU and BIU (Bus Interface

Unit).

Symbol Status

CB : Op-code read (bytes)

RB : Operand read (bytes)

QC : Clears instruction queue buffer

CW : Op-code read (words)

RW : Operand read (words)

- QN

Shows the byte count stored in the instruction queue buffer. The

display range is 0 to 4.

- 76543210

Shows the level of external trace signal input cable EXTIN0 to

EXTIN7.

- h” m’ s: ms. us

Shows the elapsed time after starting the user program.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 65 of 88

Page 68

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(2) Suspending and resuming trace measurement

1) Suspending trace measurement

Suspend

Click this toolbar button to suspend the trace measurement in progress.

2) Resuming trace measurement

Re-Start

Click this toolbar button to resume the trace measurement in progress.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 66 of 88

Page 69

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

(3) Trace point setup window

1) Trace point setup window

Trace Point Setting Window in initial state

Clicking this toolbar button opens the trace point setting

window.

You can set events in the same way as for the hardware breakpoints.

Specifying a trace ra nge

You can specify a trace range for the trace event.

- Break 32K cycles of instruction execution before the user program stopped is recorded.

- Before 32K cycles of instruction execution before a trace point condition was met is recorded.

- About 16K cycles of instruction execution before and after a trace point condition was met is recorded.

- After 32K cycles of instruction execution after a trace point condition was met is recorded.

- Full 32K cycles of instruction execution after a trace began is

recorded.

2) Setting the trace write condition

Setting the trace write condition

You can specify a condition for the cycles to be written into the trace memory.

- Total All cycles are written into memory.

- Pick up Only the cycles in which the specified condition was met are

written into memory.

- Exclude Only the cycles in which the specified condition was not met are

written into memory.

When you have finished setting the trace write condition, click this button. The Realtime-trace Write Condition dialog box shown below will appear.

3) Realtime trace Write Condition dialog box

Write mode

Only the cycle in which the specified Start event occurred

A range of cycles from when the specified Start event occurred to when the specified Start event became nonexistent.

A range of cycles from when the specified Start event occurred to when the specified End event occurred.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 67 of 88

Page 70

M306H7T3-RPD-E User’s Manual 3. Usage (How to Use the Emulator Debugger)

3.8 RAM Monitor Window

This function makes it possible to make reference to the changes in memory contents without impairing the real-time

performance for target program execution. The emulator PC4701 system is provided with the 1K-byte RAM monitoring area,

which can be arranged in the 1K-byte space from any continuous address.

(1) RAM monitor window

1) RAM monitor window

RAM monitor

Clicking this button opens the RAM monitor window.

2) RAM monitor display area

Changing the RAM monitor display area

This window shows changes of memory contents while the user

program is executed. This is accomplished by using the real-time

RAM monitor function, and the memory contents corresponding to

the RAM monitor area are displayed in dump form. The memory

contents displayed here are updated at given intervals (by default,

every 100 ms) during user program execution.

The background colors of the data display and the code display

sections change with the access attribute as described below.

- Green : Addresses accessed for read

- Red : Addresses accessed for write

- White : Addresses not accessed

The background colors can be changed as necessary.

3) RAM monitor area setting dialog box

RAM monitor area setting window

You can set the start address of the RAM area to be monitored.

The 1 KB of the arbitrary continuous space form the specified start

address can be displayed.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 68 of 88

Page 71

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

4. Hardware Specifications

This chapter describes specifications of this product.

4.1 Target MCU Specifications

Table 4.1 lists the specifications of target MCUs which can be debugged with this product.

Table 4.1 Specifications of target MCUs for the M306H7T3-RPD-E

Item Description

Applicable MCU M16C/6H Group M306H7 Evaluation MCU M306H3FCFP, M306H7FG-TOOL Applicable MCU mode Single-chip mode Emulation Memory 1 MB Operating voltage VCC2=4.0--5.5 V, VCC1=3.0V--VCC2 (Xin: when operating without division)

VCC2=2.9--5.5 V, VCC1=2.9V--VCC2 (Xin: when operating in a divide-by-16 or 8-mode) VCC2=2.0--5.5 V, VCC1=2.0V--VCC2 (Xcin when operating) *VCC2=2.0V--2.6V operates only in low power dissipation mode.

Max. operating frequency 16MHz (VCC2=4.0--5.5 V, VCC1=3.0V--VCC2)

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 69 of 88

Page 72

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

4.2 Differences between the Actual MCU and Emulator

Differences between the actual MCU and emulator are shown below. When debugging the MCU using this product, be careful

about the following precautions.

IMPORTANT

Notes on Differences between the Actual MCU and Emulator:

Note on RESET* Input:

Note on NMI* Input:

 Operations of the emulator system differ from those of actual MCUs as listed below.  Reset condition

Set the time for starting up (0.2 Vcc to 0.8 Vcc) 1 μs or less.

 Initial values of internal resource data of an MCU at power-on  Internal memories (ROM and RAM) capacities etc.

With this emulator system, regardless of ROM and RAM of the MCU you use, all the areas other than the SFR area and a reserved area (addresses 27000h--27FFFh) can be read and written into.

 Oscillator circuit

In the oscillator circuit where an oscillator is connected between pins XIN and XOUT, oscillation does not occur because a converter board is used between the evaluation MCU and the user system. It is same for pins XCIN and XCOUT. For notes on when using the oscillator circuit on the user system, refer to "2.9.3 (5) Using the Oscillator Circuit on the User System" (page 41).

 A/D converter function Because a converter board, flexible cable and other devices are used between the evaluation MCU and

the user system, the A/D converter operates differently from that of the actual MCU.

 Characteristics of ports P0 to P5

This product emulates some I/O ports (P0 to P5). Therefore, the electrical characteristics of these ports differ from those of an actual MCU.

 DBC, single-step and BRK instruction interrupt vector table addresses

As the emulator uses the DBC, single-step and BRK instruction interrupt vector table addresses, when reading these addresses, the downloaded data cannot be read (see Table 4.2).

Table 4.2 Vector table addresses for the emulator

 Pins P57/CLKout

When pins P57/CLKout are used for CLKout function and Fc is selected by Clock output selection in stop mode, CLKout output does not stop.

 A low input from the user system to pin RESET* is accepted only while a user program is being

executed (only while the RUN status LED on the PC4701's front panel is lit).

 A low input from the user system to pin NMI* is accepted only while a user program is being executed

(only while the RUN status LED on the PC4701's front panel is lit).

Factor of interruption Vector table addresses Data read

DBC*1 FFFF4h--FFFF7h Indefinite

Single-step*1 FFFECh--FFFEFh Indefinite

BRK instruction FFFE4h--FFFE7h Indefinite

*1 Interruption for the emulator only

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 70 of 88

Page 73

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

IMPORTANT

Notes on Maskable Interrupts:

Note on DMA Transfer:

Note on Pullup Control:

Note on Setting "1" to Protect Bit 2 (PCR2) with Sub Clock:

Notes on Setting "1" to Protect Bit 2 (PRC2) in Division by 2 Mode:

Note on the Input Thresholds for the Pins P1_5/INT3, P1_6/INT4 and P1_7/INT5

Note on Final Evaluation:

 Even if a user program is not being executed (including when run-time debugging is being performed),

the evaluation MCU keeps running so as to control the emulation pod. If a maskable interrupt is requested when the user program is not being executed (including when run-time debugging is being performed), the maskable interrupt request cannot be accepted, because the emulator disables interrupts. The interrupt request is accepted immediately after the user program execution is started.

 Take note that when the user program is not being executed (including when run-time debugging is

being performed), a peripheral I/O interruption is not accepted.

 With this product, the program is stopped with a loop program to a specific address. Therefore, if a

DMA request is generated while the program is stopped, a DMA transfer is executed, but it may not be performed correctly. Also note that the below registers have been changed to generate a DMA transfer as explained here even when the program is stopped.

DMA0 transfer counter registers : TCR0 DMA1 transfer counter registers : TCR1

 With this product, ports P0 to P5 are not pulled up by the pullup control register. To pull up the ports P0

to P5, mount the included network resistor (51 kΩ) to the inside of the emulator as occasion demands. How to mount it, refer to "2.9.5 Installing and Removing Network Resistors for Pullup" (page 45).

*Note: Ports P6 to P9 are pulled up by the pullup control registers. *Note: Pullup control registers themselves can be read and written into properly.

 When the CPU clock is set to the sub-clock (low-speed mode or low power dissipation mode), even if

you enable the PRC2 bit, writing to the register protected by the PRC2 bit (PD9, S3C and S4C registers) cannot be done properly. When you enable the PRC2 bit and write to the register protected by the PRC2 (PD9, S3C and S4C registers), do not set the CPU clock to the sub-clock.

 Under the following conditions, even if you enable the PRC2 bit, writing to the register protected by the

PRC2 bit (PD9, S3C and S4C registers) cannot be done properly. (1) Between when stop mode is released and when a hardware reset is executed (2) Between when low power dissipation mode is enabled and when a hardware reset is executed

 Therefore, if the condition (1) or (2) applies, when you enable the PRC2 bit and write to the register

protected by the PRC2 (PD9, S3C and S4C registers), set the CPU clock neither to the main clock in division by 2 mode nor to the on-chip oscillator clock in division by 2 mode.

 With this product, regarding pins P1_5/INT3, P1_6/INT4 and P1_7/INT5, a device which port or data

bus inputs to and a device which INT interrupt inputs to are different as follows:

Device which port or data bus inputs to: Port emulation FPGA (input level: TTL) Device which INT interrupt inputs to: Evaluation MCU for emulating peripheral functions (input

level: CMOS Schmidt) Therefore, the port input level can be read as “H” immediately after an INT interrupt (falling), and the port input level can be read as “H” immediately before an INT interrupt (rising).

 Be sure to evaluate your system with an evaluation MCU. Before starting mask production, evaluate

your system and make final confirmation with a CS (Commercial Sample) version MCU.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 71 of 88

Page 74

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

4.3 Connection Diagram

Figure 4.1 shows a connection diagram of the M306H7T3-RPD-E. This connection diagram mainly shows the interface section.

The circuits not connected to the user system such as the emulator's control system are omitted. The signals not shown in

Figure 4.1 connect the evaluation MCU and the user system directly.

Tables 4.3 to 4.4 show IC electric characteristics of this product for reference purposes.

M306H7FG-TOOL(IC8)

I/O Emulate MCU

AN00--AN07

P60--P67 P70--P77 P80--P84 P90--P97

P85/NMI

P86/Xcout

P87/Xcin

Xout

VDDIO

SW5

SW4

VDDIO

100KΩ

SW2

P86/Xcout

OPEN

Xout

74HC4066

1KΩ

SW3

100Ω

P87

Xcin

P60--P67 P70--P77 P80--P84 P90--P97

P85/NMI

P86/Xcout

P87/Xcin

Xout

CNVSS

RM1

Socket mounted

33Ω

RM2

Socket mounted

33Ω

RM3

Socket mounted

33Ω

RM4

Socket mounted

33Ω

RM5

Socket mounted

33Ω

RM6

Socket mounted

33Ω

P62F2(IC4)

Port Emulate FPGA

P00--P07

P10--P17

P20--P27

P30--P37

P40--P47

P50--P57

Figure 4.1 Part of the connection diagram of the M306H7T3-RPD-E

VDD2

CNVSS

P00--P07

P10--P17

P20--P27

P30--P37

P40--P47

P50--P57

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 72 of 88

Page 75

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

Table 4.3 Electrical characteristics of the 74HC4066

Symbol Item Condition

RON ON resistor Vcc=4.5V - 96 170 ΔRON ON resistor difference Vcc=4.5V - 10 - IOFF

IIZ

Leak current (Off) Leak current (On, output: open)

Vcc=12.0V - Vcc=12.0V - -

Standard values

Min. Standard Max.

±100 ±100

Unit

Ω

Table 4.4 Electrical characteristics of the Port Emulation FPGA

Symbol Item Condition

Standard values

Min. Standard Max.

Unit

VIH High level input voltage 2.0 - 5.5 VIL Low level input voltage -0.5 - 0.8

IOH=-8mA DC,

VOH High level output voltage

Vcc=4.75V

OH=-8mA DC,

I Vcc=3.00V IOL=8mA DC,

VOL Low level output voltage

Vcc=4.75V I

OL=8mA DC,

Vcc=3.00V

II Input leak current VI=Vcc or GND

2.4 - -

- - 0.45

-10

－

10 μA

IOZ Leak current (Tristate) Vo=Vcc or GND -40 - 40 μA

CIN I/O pin input capacitance

IN=0V,

f=1.0MHz

- - 8 pF

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 73 of 88

Page 76

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

4.4 External Dimensions

4.4.1 External Dimensions of the Emulation Pod

Figure 4.2 shows external dimensions of the M306H7T3-RPD-E.

40 . 0

33.0

11.0

189.0

10 . 5

11.0

437.0

140.0

Unit: mm

Figure 4.2 External dimensions of the emulation pod

193.0

3.0

52.0

3.0

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 74 of 88

Page 77

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

4.4.2 External Dimensions of the M30800T-PTC

Figure 4.3 shows external dimensions of the converter board M30800T-PTC for a 100-pin LCC (included with the

M306H7T3-RPD-E).

40.0

55.0

M30800T-PTC

CN1

100

MADE IN JAPAN

13.5

CN2

13.5

External dimension when connecting the 100-pin LCC socket

Figure 4.3 External dimensions of the M30800T-PTC

10.8

16.3 Unit: mm

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 75 of 88

Page 78

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

4.5 Notes on Using This Product

Notes on using this product are listed below. When debugging the MCU using he emulator, be careful about the following precautions.

IMPORTANT

Note on the Version of the Emulator Debugger:

 Be sure to use this product with one of the following emulator debuggers.

1. M16C PC4701 Emulator Debugger

2. M3T-PD30 V8.20 Release 1 or later

Note on Selecting the MCU File:

 It is necessary to make an MCU file which contains information such as, SFR area, internal RAM area

and internal ROM area, etc. to use this product. For creating an MCU file, see “3.1 Making an MCU File” on page 48. For each memory map of MCU , refer to its data sheet.

Note on Malfunctions in the PC4701 System

Notes on Downloading Firmware:

Notes on the Self-check:

Note on Quitting the Emulator Debugger:

 If the emulator malfunctions because of interference like external noise, do the following to remedy the

trouble

(1) Press the RESET switch on the emulator upper panel. (2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then

reactivate it.

 Before using this product for the first time, it is necessary to download the dedicated firmware (control

software built into the PC4701). Please note that, to do this, it is necessary to start up the emulator main unit in maintenance mode. For firmware download procedures, see "2.6.2 Downloading Firmware in Maintenance Mode" (page 28). Once the firmware has been downloaded, th e product can be used by simply turning on the power.

 Do not shut off the power while downloading the firmware. If this happens, the product will not start up

properly. If power is shut off unexpectedly, red ownload the firmware in maintenance mode.

 Be sure to disconnect the user system before downloading the firmware.

 If the self-check does not result normally (excluding target status error), the emulation pod may be

damaged. Then contact your local distributor.

 Be sure to disconnect the user system before executing the self-check

 To restart the emulator debugger after it ends, always shut power to the emulator off once and wait

about 10 seconds, then turn the power on again.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 76 of 88

Page 79

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

IMPORTANT

Note on Clock Supply to the MCU:

Note on Setting the Work Area When Starting Up the Emulator Debugger:

Note on Stack Area:

Notes on MAP References and Settings:

Note on Operation When Not Executing the User Program:

Note on Stop and Wait Modes:

Note on Watchdog Function:

 A clock supplied to the evaluation MCU is selected by the Clock tab in the Init dialog box of the

emulator debugger. (1) When Internal is selected: A clock generated by the oscillation circuit in the emulation pod is supplied to the evaluation MCU.

The clock is continually supplied to the evaluation MCU regardless of "user system clock status"

and "user program execution status" (2) When External is selected: Clock supply to the evaluation MCU depends on oscillation status (oscillate/off) of the user system.

 With this product, the emulator uses 54 bytes as a work area in emulation memory. Set the work area

address at 10000h. For more details, see "3.2 Setting the Work Area" (page 48).

 With this product, a maximum 7 bytes of the user stack is consumed. Therefore, ensure the +7 bytes

maximum capacity used by the user program as the user stack area. If the user stack does not have enough area, do not use areas which cannot be used as stack (SFR area, RAM area which stores data, or ROM area) as a work area. Using areas like this is a cause of user program crashes and destabilized emulator control.

 For details on referencing and setting MAP information, see the emulator debugger user's manual.

Make settings as follows: (1) MAP = INT

The emulation memory inside this product becomes effective. Set this at MCU internal ROM debugging.

(2) MAP = EXT

The emulation memory inside this product is not used. Set this where the MCU internal resource (SFR) or resources on the user system are used.

 Be sure to set the work area as MAP = INT.

 With this product, bit 7 of processor mode register 1 (wait bit PM17) is forcibly set to "1" (with wait)

when the user program is not executed (e.g. when the program is stopped or when run-time debugging is being performed). Therefore, if the external area set to 0 wait is accessed by other than the user program (such as debugging operation), one wait is inserted. However, when wait bit PM17 is referenced by the dump window etc. the value set during user program execution is displayed.

 Do not single step an instruction shifting to stop or wait mode. It may cause communication errors..

 The MCU's watchdog timer can be used only while programs are being executed. To use it otherwise,

disable the watchdog timer.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 77 of 88

Page 80

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

IMPORTANT

Note on M1 (Mode Selection Input) Pin:

Note on Reading Internal Resources of the MCU:

Note on Protect Register:

Note on Breaks:

Notes on Software Breaks:

 As the evaluation MCU in this product and the M1 pin of the user system are not connected, this

product is not affected by the status ("H", "L" or "OPEN") of the M1 pin of the user system. Be sure to check the status of the M1 pin when evaluating with an actual MCU.

 When the registers listed in Table 4.5 are read with an emulator, those results will be the following (the

data in the MCU are not effected). (1) Results of real-time trace The data values of the cycles read are not displayed correctly. (2) Real-time RAM monitor The data values read are not displayed correctly. Table 4.5 Resisters and symbols not displayed normally

Resister Symbol DMA source pointers 0, 1 SAR0, SAR1 DMA destination pointers 0, 1 DAR0, DAR1 DMA transfer counters 0, 1 TCR0, TCR1 DMA control resisters 0, 1 DM0CON, DM1CON

 The protect is not canceled when bit 2 of protect register PRCR (PRC2), which enables writing into the

port P9 direction register and the SI/Oi control register, is changed with the below procedure.

(1) Step execution of the "instruction for setting ("1") PRC2" (2) Execution from the instruction setting "1" to PRC2 where a software breakpoint is set

(3) Setting the break point from the "instruction for setting ("1") PRC2" to when the "setting the port

P9 direction register and the SI/Oi control register"

(4) Setting ("1") PRC2 from the Memory Window or Script Window

 The area displaying break points in the program window of the emulator debugger shows the following

breaks. (1) Software break This is a debugging function which generates a BRK interruption by changing an instruction at a

specified address to a BRK instruction (00h) to break a program immediately before the system executes an instruction at a specified address. The instruction at the preset address will not be

executed. (2) Hardware break This is a debugging function which breaks a program by setting the detection of an execution of an

instruction at a specified address as a break event. The program will break after the instruction at

the specified address is executed.

 Software breaks change the instruction at a specified address to a BRK (00h). Therefore, take note that

when you reference the result of a trace in bus mode, "00h" is displayed.

 The BRK instruction can be used for the emulator only. You cannot use it in a user program.  It is not possible to use a software break and a hardware break at the same time. If doing so, it may not

operate normally.

 In the area where the MAP setting is EXTERNAL, software breaks cannot be used.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 78 of 88

Page 81

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

IMPORTANT

Note on Power Supply to the User System:

 Pins Vcc1 and Vcc2 are connected to the user system to observe the voltage. Therefore, the power is

not supplied to the user system from the emulator, design your system so that the user system is powered separately. (1) The voltage of the user system should be within the operating range of the evaluation MCU. (2) Do not change the voltage of the user system after turning on the power.

Notes on Addre ss-Match Interrupts:

Note on Acce ssing Addres ses 00000h and 00001h:

Note on Debugging Operations After Releasing a Reset from the Target:

 To debug address-match interrupts, set a software break or hardware break at the top address of the

address-match interrupt process. If you set a software break or hardware break at an address where an address-match interrupt occurs, the program may run out of control.

 When an address at which an address-match interrupt occurs is executed in single-step mode, the

program stops after executing the first instruction after returning from the address-match interrupt processing.

 With the M16C/60 Series MCUs, when a maskable interrupt is generated, the interrupt data (interrupt

number and interrupt request level) stored in addresses 00000h and 00001h are read out. Also, the interrupt request bit is cleared when address 00000h or 00001h is read out. Consequently, when the address 00000h readout instruction is executed or when address 00000h or 00001h is read out in the cause of a program runaway, a malfunction occurs in that the interrupt is not executed despite the interrupt request, because the request bit of the highest priority interrupt factor enabled is cleared. For this malfunction, when the reading out to the address 00000h or 00001h is generated excluding the interrupt, the LED (yellow) lights up to alarm. When this LED lights, there is a possibility of wrong access, therefore check the program. This LED is turned off by the system reset switch of the emulator main unit.

 Do not execute debugging operations such as setting a software or hardware break, runtime debugging

after releasing a reset from the user system until an interrupt stack pointer (ISP) is set in the user program.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 79 of 88

Page 82

M306H7T3-RPD-E User’s Manual 5. Troubleshooting

5. Troubleshooting

This chapter describes how to troubleshoot when this product does not work properly.

5.1 Flowchart to Remedy the Troubles

Figure 5.1 shows the flowchart to remedy troubles from when power to the emulator is activated until the emulator debugger

starts up. Check this while the user system is not connected. For the latest FAQs visit the Renesas Tools Homepage.

http://www.renesas.com/en/tools

Turning on the power of PC4701

1. Check emulator system connections.

Init dialog box of emulator debugger

1. Check the operating environment etc. of the emulator

Error displayed

See "5.2 (2) Program Window is Not Displayed at Debugger

Program window of emulator debugger

Figure 5.1 Flowchart to remedy troubles

PC4701 Front panel LEDs

displayed

Not normal

See "2.4 Connecting the PC4701" (page 23).

2. Redownload the firmware. See "2.6 Downloading Firmware" (page 28).

3. Restart the PC4701 system.

Not normal or error displayed

debugger. See the emulator debugger user's manual (online manual).

2. Reinstall the emulator debugger.

Startup (User System Connected)" (page 82).

See "5.2 (3) Program Window is Not Displayed at Debugger

Startup (User System Not Connected)" (page 83).

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 80 of 88

Page 83

M306H7T3-RPD-E User’s Manual 5. Troubleshooting

5.2 When the Emulator Debugger Does Not Start Up Properly

(1) When the LED Display of the PC4701 is Abnormal

Table 5.1 LED's abnormal display and its checkpoints

Connection to

Error

LEDs do not light up. -

All LEDs remain lit. -

The "POWER" LED of "STATUS OF TARGET" does not light up.

The "CLOCK" LED of "STATUS OF TARGET" does not light up.

The "RESET" LED of "STATUS OF TARGET" does not go out.

the user

Connected

Disconnected

Connected

system

Check that the power cable is connected to the PC4701.

See the PC4701 user's manual.

Check the connection between the PC4701 and this product.

See "2.4 Connecting the PC4701" (page 23).

Check that power (Vcc and GND) is properly supplied to the user system. (1) Check that both the main/sub clocks are not set to

“External” in the emulator debugger..

See the CLK command of the emulator debugger.

(2) Check the oscillator circuit board is mounted on this

product and it is oscillating properly.

See "2.9.3 Selecting Clock Supply" (page 38).

(1) When the clock supply is set to “External”, check that the

oscillation circuit on the user system is oscillating correctly.

(2) Check the switches in the emulation pod are correctly set.

See “2.9.4 Switch settings” (page 42)

Check that the reset pin of the user system is at “H” level.

Checkpoint

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 81 of 88

Page 84

M306H7T3-RPD-E User’s Manual 5. Troubleshooting

(2) Program Window is Not Displayed at Debugger Startup (User System Connected)

Table 5.2 Checkpoints of errors when starting up the emulator debugger (user system connected)

Error Checkpoint

ERROR 16005:

Can't connect with the target.

(1) Check the connection between the PC4701 and host machine.

See the PC4701 User's Manual.

(2) Check that the PC4701 is powered on.

See the PC4701 User's Manual.

(3) Check that all switch settings on the rear of the PC4701 and

interface cable settings of the emulator debugger match.

See the PC4701 User's Manual and the emulator debugger user's

manual (online manual).

ERROR 16211:

The version of the emulator and the firmware on the target are not same.

(1) Check the connection between the PC4701 and this product.

See “2.4 Connecting the PC4701” (page 23)

(2) Download the proper firmware.

See "2.6 Downloading Firmware" (page 28).

(3) Choose the proper MCU file in the Init dialog box. See the emulator debugger user's manual (online manual). (4) Check that the descriptions in the MCU file are correct.

See "3.1 Making an MCU File" (page 48).

ERROR 16215:

Cannot communicate with the debugging monitor. Execute the RESET command.

(1) Check the connection between the PC4701 and this product.

See “2.4 Connecting the PC4701” (page 23)

(2) Check that the reset pin of the user system is at “H” level.

See the MCU specifications.

(3) Check that CNVSS is held low.

See the MCU specifications.

(4) Check that the oscillator circuit of the emulation pod is oscillating

properly.

See "2.9.3 Selecting Clock Supply" (page 38)

ERROR 16014:

Communication ERROR. Can't accept data.

(1) Check that the oscillator circuit of the user system is oscillating

properly.

See "2.9.3 Selecting Clock Supply" (page 38).

(2) Check that the PC4701 LEDs at startup show normal operation.

See "2.5.3 LED Display When the Emulator Starts Up Normally"

(page 27).

ERROR 16231:

There was sent undefined data from the emulator.

Check that the emulator debugger has not been started up without shutting down the PC4701.

See "4.5 IMPORTANT: Note on Quitting the Emulator Debugger" (page 76).

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 82 of 88

Page 85

M306H7T3-RPD-E User’s Manual 5. Troubleshooting

(3) Program Window is Not Displayed at Debugger Startup (User System Not Connected)

Table 5.3 Checkpoints of errors when starting up the emulator debugger (user system not connected)

Error Checkpoint

ERROR 16005:

Can't connect with the target.

(1) Check the connection between the PC4701 and host machine.

See the PC4701 User's Manual.

(2) Check that the PC4701 is powered on.

See the PC4701 User's Manual.

(3) Check that all switch settings on the rear of the PC4701 and

interface cable settings of the emulator debugger match.

See the PC4701 User's Manual and the emulator debugger user's

manual (online manual).

ERROR 16211:

The version of the emulator and the firmware on the target are not same.

(1) Check the connection between the PC4701 and this product.

See "2.4 Connecting the PC4701" (page 23).

(2) Download the proper firmware.

See "2.6 Downloading Firmware" (page 28).

(3) Choose the proper MCU file in the Init dialog box.

See the emul ator debugger user's manual (online ma n ual ).

(4) Check that the descriptions in the MCU file are correct.

See "3.1 Making an MCU File" (page 48).

ERROR 16215:

Cannot communicate with the debugging monitor. Execute the RESET command

(1) Check that switch settings in the emulation pod are correct.

See "2.9. 4 Sw i tc h Set t i ngs " (p age 42).

(2) Check that the oscillator circuit of the emulation pod is oscillating

properly.

See "2.9.3 Selecting Clock Supply" (page 38).

ERROR 16014:

Communication ERROR. Can't accept data.

Check that the PC4701 LEDs at startup show normal operation.

See "2.5.3 LED Display When the Emulator Starts Up Normally" (page 27).

ERROR 16231:

There was sent undefined data from the emulator.

Check that the emulator debugger has not been started up without shutting down the PC4701.

See "4.5 IMPORTANT: Note on Quitting the Emulator Debugger" (page 76).

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 83 of 88

Page 86

M306H7T3-RPD-E User’s Manual 5. Troubleshooting

5.3 How to Request for Support

After checking the items in "5 Troubleshooting", fill in the text file which is downloaded from the following URL, then send

the information to your local distributor.

http://tool-support.renesas.com/eng/toolnews/registration/support.txt

For prompt response, please specify the following information:

(1) Operating environment

- Operating voltage:

- Operating frequency:

- Operating mode: Single-chip, memory expansion, or microprocessor mode

- Clock supply to the MCU: Internal oscillator/External oscillator

(2) Condition

- The emulator debugger starts up/does not start up

- The error is detected/not detected in the self-check

- Frequency of errors: always/frequency ( )

(3) Problem

[V]

[MHz]

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 84 of 88

Page 87

M306H5T3-RPD-E User’s Manual 6. Maintenance and Guarantee

6. Maintenance and Guarantee

This chapter describes how to maintenance, repair provisions and how to request for repair.

6.1 User Registration

When you purchase our product, be sure register as a user. For user registration, refer to “User registration” (page 11) of this

user's manual.

6.2 Maintenance

(1) If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth. Do not use thinner or

other solvents because these chemicals can cause the equipment's surface coating to separate.

(2) When you do not use this product for a long period, for safety purposes, disconnect the power cable from the power

supply.

6.3 Guarantee

If your product becomes faulty within one year after its purchase while being used under good conditions by observing

"IMPORTANT" and "Precautions for Safety" described in this user's manual, we will repair or replace your faulty product free

of charge. Note, however, that if your product's fault is raised by any one of the following causes, we will repair it or replace it

with new one with extra-charge:

- Misuse, abuse, or use under extraordinary conditions

- Unauthorized repair, remodeling, maintenance, and so on

- Inadequate user's system or misuse of it

- Fires, earthquakes, and other unexpected disasters

In the above cases, contact your local distributor. If your product is being leased, consult the leasing company or the owner.

6.4 Repair Provisions

(1) Repair with extra-charge

The products elapsed more than one year after purchase can be repaired with extra-charge.

(2) Replacement with extra-charge

If your product's fault falls in any of the following categories, the fault will be corrected by replacing the entire product

instead of repair, or you will be advised to purchase new one, depending on the severity of the fault.

- Faulty or broken mechanical portions

- Flaw, separation, or rust in coated or plated portions

- Flaw or cracks in plastic portions

- Faults or breakage caused by improper use or unauthorized repair or modification

- Heavily damaged electric circuits due to overvoltage, overcurrent or shorting of power supply

- Cracks in the printed circuit board or burnt-down patterns

- Wide range of faults that makes replacement less expensive than repair

- Unlocatable or unidentified faults

(3) Expiration of the repair period

When a period of one year elapses after the model was dropped from production, repairing products of the model may

become impossible.

(4) Transportation fees at sending your product for repair

Please send your product to us for repair at your expense.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 85 of 88

Page 88

M306H5T3-RPD-E User’s Manual 6. Maintenance and Guarantee

6.5 How to Make Request for Repair

If your product is found faulty, follow the procedure below to send your product for repair.

Customer

Distributor

Renesas Solutions When the faulty product is repaired, it will be returned to the customer at the earliest

Fill in the Repair Request Sheet included with this product, then send it along with this product for repair to your local distributor. Make sure that information in the Repair Request Sheet is written in as much detail as possible to facilitate repair.

After checking the contents of fault, the distributor should please send the faulty product along with the Repair Request Sheet to Renesas Solutions Corp.

convenience.

CAUTION

Note on Transporting the Product:

 When sending your product for repair, use the packing box and cushion material supplied with

this product when delivered to you and specify handling caution for it to be handled as precision equipment. If packing of your product is not complete, it may be damaged during transportation. When you pack your product in a bag, make sure to use conductive polyvinyl supplied with this product (usually a blue bag). When you use other bags, they may cause a trouble on your product because of static electricity.

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 86 of 88

Page 89

Emulation Pod M306H7 for M16C/6H Group M306H7T3-RPD-E User’s Manual

Publication Date: Sep. 01, 2005 Rev.1.00

Published by:

Edited by:

Sales Strategi c Planning Div. Renesas Technology Corp

Microcomputer Tool Development Department Renesas Solutions Corp.

Page 90

M306H7T3-RPD-E

User’s Manual

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan

REJ10J0964-0100(T)

Renesas M306H7T3-RPD-E User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Important

Precautions for Safety

Contents

User Registration

Terminology

1. Outline

1.1 Package Components

1.2 Other Tool Products Required for Development

1.3 System Configuration

1.3.1 System Configuration

1.3.2 Names and Functions of the PC4701 Front Panel LEDs

1.4 Specifications

1.5 Operating Environment

2. Setup

2.1 Flowchart of Starting Up the Emulator

2.3 Connecting the Host Machine

2.4 Connecting the PC4701

2.4.1 Connecting the Cable to the PC4701

2.4.2 Connecting the FLX120-RPD to the Emulation Pod

2.4.3 PC4701 and Emulation Pod Arrangement

2.5 Turning ON the Power

2.5.1 Checking the Connections of the Emulator System

2.5.2 Turning ON/OFF the Power

2.5.3 LED Display When the Emulator S tarts Up Normally

2.6 Downloading Firmware

2.6.1 When It is Necessary to Download Firmware

2.6.2 Downloading Firmware in Maintenance Mode

2.7 Self-check

2.7.1 Self-check Procedure

2.7.2 If an Error is Detected in the Self-check

2.8 Connecting the User System

2.8.1 Connecting to a 100-pin LCC socket

2.8.2 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1)

2.8.3 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2)

2.8.4 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3)

2.9 Changing Settings

2.9.1 Removing/Attaching the Upper Cover

2.9.2 Each Setting

2.9.3 Selecting Clock Supply

2.9.4 Switch Settings

2.9.5 Installing and Removing Network Resistors for Pullup

2.9.6 Bypass Capacitors for A/D Converter

2.9.7 Connection Diagram of Data Slicer

3. Usage (How to Use the Emulator Debugger)

3.1. Making an MCU File

3.2 Setting the Work Area

3.3 Starting Up the Emulator Debugger

3.3.1 Init Dialog Box

3.3.2 Checking Connections of the Emulator System

3.4 Downloading Program

3.5 Program execution

3.6 Hardware Break

3.7 Trace Window

3.8 RAM Monitor Window

4. Hardware Specifications

4.1 Target MCU Specifications

4.2 Differences between the Actual MCU and Emulator

4.3 Connection Diagram

4.4 External Dimensions

4.4.1 External Dimensions of the Emulation Pod

4.4.2 External Dimensions of the M30800T-PTC

4.5 Notes on Using This Product

5. Troubleshooting

5.1 Flowchart to Remedy the Troubles

5.2 When the Emulator Debugger Does Not Start Up Properly

5.3 How to Request for Support

6. Maintenance and Guarantee

6.1 User Registration

6.2 Maintenance

6.3 Guarantee

6.4 Repair Provisions

6.5 How to Make Request for Repair