Page 1
M3062PT-80FPB
Converter Board for Connecting FLX160 to 80-pin 0.65-mm-pitch QFP (80P6S-A)
User's Manual
• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more
reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property
damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive,
auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation,
Renesas Solutions Corporation or a third party.
• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any third-party's rights,
originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the
time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas Solutions Corporation without notice
due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor for the latest product information before purchasing a product listed herein. The
information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions
Corporation assume no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://
www.renesas.com).
• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure
to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology
Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or other loss resulting from the information contained herein.
• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human
life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular,
medical, aerospace, nuclear, or undersea repeater use.
• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce in whole or in part
these materials.
• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese
government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and
regulations of Japan and/or the country of destination is prohibited.
• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products contained therein.
Keep safety first in your circuit designs!
Notes regarding these materials
• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your program you have
finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing integration test, evaluation, or some
experiment else.
• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
• Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge. However, this does
not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any circumstances.
• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall under the
application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan.
Renesas Tools Homepage http://www.renesas.com/en/tools
Precautions to be taken when using this product
If the requirements shown in the "CAUTION" sentences are ignored,
CAUTION
the equipment may cause personal injury or damage to the products.
Rev. 1.00
July 1, 2003
( 1 / 4 )
REJ10J0204-0100Z
Page 2
1. Outline
The M3062PT-80FPB is a converter board for connecting
the 160-core flexible cable FLX160 to a foot pattern for 80pin 0.65-mm-pitch QFP (80P6S-A).
2. Package Components (See Figure 1)
(1) M3062PT-80FPB converter board...........................1
(2) YQPACK080SB (made by Tokyo Eletech Corporation) ..... 1
(3) NQPACK080SB (made by Tokyo Eletech Corporation) ..... 1
(4) YQ-GUIDE's (made by Tokyo Eletech Corporation) ............ 4
(5) M3062PT-80FPB User's Manual (this manual)
3. Specifications
Table 1 Specifications
M3062PT-80FPB
YQ-GUIDE's (x4)
Figure 1 Package components
YQPACK080SB
NQPACK080SB
Applicable package
Insertion/removal iterations of connector
80P6S-A (80-pin 0.65-mm-pitch QFP)
50 times guaranteed
4. Usage (See Figure 2)
The M3062PT-80FPB can be used for debugging and onboard
evaluation in common by mounting the NQPACK080SB on
the target system.
(1) For debugging
Mount the NQPACK080SB on the foot pattern of the
target system and attach the YQPACK080SB on it. And
connect the probe of the emulation pod to the upper
connectors of the M3062PT-80FPB. Then connect the
YQPACK080SB and the M3062PT-80FPB.
(2) For onboard evaluation
Mount an MCU with on-chip flash memory or one-time
PROM and the HQPACK080SB (separately available)
in that order on the NQPACK080SB on the target system.
Before using the M3062PT-80FPB, be sure to read "7.
Precautions" on page 4.
(1) For debugging
M3062PT-80FPB
YQ-GUIDE's (x4)
YQPACK080SB
M3062PT3-RPD-E
M3062NT3-RPD-E
M3062PT-EPB
(2) For onboard evaluation
HQPACK080SB
(separately available)
80-pin 0.65-mm-pitch
(80P6S-A) foot pattern
Figure 2 Usage
( 2 / 4 )
NQPACK080SB
: Position of No. 1 pin
Be sure to align the pins.
MCU with on-chip flash
memory or one-time PROM
Page 3
5. Connection Procedure (See Figure 3)
The procedure for connecting the M3062PT-80FPB is shown
below.
(1) Mount the NQPACK080SB on the target system.
(2) Attach the YQPACK080SB on the NQPACK080SB.
(3) Secure the four corners of the YQPACK080SB with the
YQ-GUIDE's.
• Do NOT use the screws included with the
YQPACK080SB.
• Do NOT use the screwdriver included with the
NQPACK080SB that is used only for the
HQPACK080SB. It is not for the YQ-GUIDE's.
(4) Attach the probe of the emulation pod to the M3062PT-
80FPB.
(5) Attach the M3062PT-80FPB on the YQPACK080SB.
M3062PT-80FPB
YQ-GUIDE's (x4)
YQPACK080SB
NQPACK080SB
80-pin 0.65-mm-pitch
(80P6S-A) foot pattern
M3062PT3-RPD-E
M3062NT3-RPD-E
M3062PT-EPB
Use a slotted screwdriver.
: Position of No. 1 pin
Be sure to align the pins.
Figure 3 Connection procedure
6. External Dimensions and a Sample Foot Pattern
Figure 4 External dimensions and a sample foot pattern
Unit: mm
( 3 / 4 )
Page 4
7. Precautions
CAUTION
Cautions to Be Taken for This Product:
• To connect the YQPACK080SB, be sure to use the included YQ-GUIDE's.
• Do NOT use the screws included with the YQPACK080SB for connecting the
YQPACK080SB.
IMPORTANT
Notes on This Product:
•We cannot accept any request for repair.
• The HQPACK, NQPACK, YQPACK and YQ-Guide are trademarks of Tokyo
Eletech Corporation.
• For purchasing the NQPACK080SB, YQPACK080SB, HQPACK080SB, contact
the following:
Tokyo Eletech Corporation http://www.tetc.co.jp/e_tet.htm
• For inquiries about the product or the contents of this manual, contact your local
distributor.
Renesas Tool Homepage http://www.renesas.com/en/tools
8. Correspondence of the Pins
Table 2 Correspondence of the pins
CN1 IC1 CN1 IC1 CN2 IC1 CN2 IC1
1a - 1b 8 1a - 1b 9
2a 7 2b 6 2a 10 2b 11
3a 6 3b - 3a 12 3b 13
4a - 4b - 4a 14 4b 15
5a - 5b - 5a 16 5b 17
6a - 6b - 6a 18 6b 19
7a 5 7b - 7a 20 7b 21
8a 4 8b 3 8a - 8b -
9a 2 9b 1 9a - 9b 10a 80 10b - 10a 22 10b 11a - 11b 79 11a - 11b 23
12a 78 12b 77 12a 24 12b 13
13a 76 13b 75 13a 25 13b 11
14a 74 14b 73 14a 26 14b 27
15a 72 15b 71 15a 28 15b 29
16a 70 16b 69 16a 30 16b 31
17a 68 17b - 17a - 17b 18a - 18b - 18a - 18b 19a - 19b - 19a 32 19b 33
20a - 20b - 20a 34 20b 21a - 21b - 21a - 21b 35
22a - 22b - 22a - 22b 23a - 23b 67 23a - 23b 24a 66 24b 65 24a - 24b 25a 64 25b - 25a 36 25b 37
26a - 26b - 26a 38 26b 39
27a - 27b - 27a - 27b 28a 63 28b 62 28a - 28b 29a 61 29b 60 29a - 29b 30a - 30b - 30a - 30b 31a - 31b - 31a - 31b 40
32a - 32b - 32a - 32b 41
33a - 33b - 33a - 33b 42
34a - 34b - 34a 43 34b 44
35a 59 35b 58 35a 45 35b 46
36a 57 36b 56 36a 47 36b 48
37a 55 37b 54 37a 49 37b 50
38a 53 38b 52 38a - 38b 39a 11 39b 51 39a - 39b 40a 13 40b - 40a - 40b -
("-": No connection)
( 4 / 4 )
Loading...