Renesas M30220T-PRB User Manual
M30220T-PRB
Pod Probe for M30220 and M30221 Group MCUs
User's Manual
Rev.1.00
September 1, 2003
REJ10J0281-0100Z
• NQPACK, YQPACK, YQSOCKET, YQ-Guide and HQPACK are products of Tokyo Eletech Corporation.
• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal
injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any
malfunction or mishap.
• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to
the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas
Technology Corporation, Renesas Solutions Corporation or a third party.
• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas
Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact
Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product distributor for the latest
product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or
typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage,
liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology
Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://www.renesas.com).
• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms,
please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and
products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or
other loss resulting from the information contained herein.
• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances
in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an
authorized Renesas Technology product distributor when considering the use of a product contained herein for any specific purposes,
such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce
in whole or in part these materials.
• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the
Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to
the export control laws and regulations of Japan and/or the country of destination is prohibited.
• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products
contained therein.
Keep safety first in your circuit designs!
Notes regarding these materials
• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
• Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall
under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in
Japan.
• This product is not qualified under UL or other safety standards and IEC or other industry standards. This fact must be taken into account
when bringing the product from Japan to some other country.
For inquiries about the contents of this document or product, fill in the text file the installer of the emulator debugger generates in the
following directory and email to your local distributor.
\SUPPORT\Product-name\SUPPORT.TXT
Renesas Tools Homepage http://www.renesas.com/en/tools
Precautions to be taken when using this product
( 2 / 36 )
Preface
The M30220T-PRB is a pod probe for M30220 and M30221 Groups of Renesas 16-bit microcomputers. The M30220T-PRB is used by connecting to the PC4701 emulator main unit and the
M30200T-RPD-E emulation pod main unit.
This manual mainly explains specifications and setting up of M30220T-PRB. For detail information
about the emulator main unit, emulation pod main unit, and emulator debugger, refer to each user's
manual.
Emulator main unit : PC4701M, PC4701HS, PC4701L User's Manual
Emulation pod main unit : M30200T-RPD-E User's Manual
Emulator debugger : M3T-PD30 User's Manual
To check the components of this product, refer to "2.1 Package Components" in this manual. If there
is any question or doubt about this product, contact your local distributor.
To use the product properly
Precautions for Safety:
•Both in this User's Manual and on the product itself, several icons are used to insure
proper handling of this product and also to prevent injuries to you or other persons,
or damage to your properties.
• The icons' graphic images and meanings are given in "Chapter 1 Precautions for
Safety". Be sure to read this chapter before using the product.
( 3 / 36 )
Contents
Chapter 1. Precautions for Safety ...........................................................................................6
1.1 Safety Symbols and Meanings ..............................................................................6
Chapter 2. Preparation ..........................................................................................................10
2.1 Package Components ..........................................................................................10
2.2 Other Tool Products Required for Development ................................................10
2.3 System Configuration..........................................................................................11
Chapter 3. Setting Up ...........................................................................................................14
3.1 Switch Settings....................................................................................................14
3.2 A-D Conversion Bypass Capacitor .....................................................................15
3.3 Connecting M30200T-RPD-E ............................................................................16
3.4 Connecting the Target System ............................................................................17
3.5 Making an MCU File for M3T-PD30 .................................................................21
Chapter 4. Specifications......................................................................................................24
4.1 Specifications ......................................................................................................24
4.2 External Dimensions ...........................................................................................25
(1) External Dimensions of Pod Probe ..........................................................25
(2) External Dimensions of Converter Board (FLX-144NSD) .....................25
(3) External Dimensions of Converter Board (FLX-144NSE) ......................26
(4) External Dimensions of Converter Board (FLX-120NSE) ......................26
Chapter 5. Troubleshooting ..................................................................................................28
5.1 When the Emulator Debugger Does Not Start Up Properly ...............................28
(1) When the LED Display of PC4701 is Abnormal .....................................28
(2) Errors Occur When the Emulator Debugger Starts Up
(When the target system is connected)....................................29
(3) Errors Occur When the Emulator Debugger Starts Up
(When the target system is not connected) .............................30
5.2 Operation Differs from That of MCUs with PROM ...........................................30
(1) When the A-D Conversion Values are Different from Expected Values ....30
(2) When the D-A Conversion Values are Different from Expected Values ....30
Chapter 6. Maintenance and Warranty .................................................................................32
6.1 Maintenance ........................................................................................................32
6.2 Warranty..............................................................................................................32
6.3 Repair Provisions ................................................................................................32
6.4 How to Request for Repair..................................................................................33
( 4 / 36 )
Chapter 1. Precautions for Safety
This chapter describes precautions for using this product safely and properly. For precautions for the emulator main unit,
the emulation pod main unit and the emulator debugger, refer to each user's manual included with your product.
1.1 Safety Symbols and Meanings ..................................................................................................... 6
Note on Differences between Actual MCU and Emulator...........................................................7
Note on DMA Transfer ................................................................................................................7
Note on Referencing and Setting the Work Area.........................................................................7
Notes on MAP References and Settings....................................................................................... 7
Note on Reading Out SFR Area ...................................................................................................8
( 5 / 36 )
Chapter 1. Precautions for Safety
In both the user's manual and on the product itself, several icons are used to insure proper handling
of this product and also to prevent injuries to you or other persons, or damage to your properties.
This chapter describes the precautions which should be taken in order to use this product safely and
properly. Be sure to read this chapter before using this product.
1.1 Safety Symbols and Meanings
If the requirements shown in the "WARNING"
WARNING
CAUTION
IMPORTANT
In addition to the three above, the following are also used as appropriate.
sentences are ignored, the equipment may
cause serious personal injury or death.
If the requirements shown in the "CAUTION"
sentences are ignored, the equipment may
malfunction.
It means important information on using this
product.
means WARNING or CAUTION.
Example: CAUTION AGAINST AN ELECTRIC SHOCK
means PROHIBITION.
Example: DISASSEMBLY PROHIBITED
means A FORCIBLE ACTION.
Example:
The following pages describe the symbol "IMPORTANT".
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
( 6 / 36 )
IMPORTANT
Note on Differences between Actual MCU and Emulator:
•The emulator operation differs from the mask MCU operation, as listed below:
(1) Reset condition
(2) Initial values of internal resource data at power-on
(3) Capacity of internal memory (ROM, RAM) etc.
(4) A-D converter
The A-D converter characteristics differ from actual MCU characteristics because there are
a converter board and other devices between the evaluation MCU and the target system. Make
the final evaluation of the A-D converter with the actual MCU.
(5) D-A converter
The D-A converter characteristics differ from actual MCU characteristics because there are
a converter board and other devices between the evaluation MCU and the target system. Make
the final evaluation of the D-A converter with the actual MCU.
Note on DMA Transfer:
•With this product, the program is stopped with a loop program to a specific address. Therefore, if
a DMA request is generated by a timer or other source while the program is stopped, DMA transfer
is executed. However, make note of the fact that DMA transfer while the program is stopped may
not be performed correctly. Also note that the below registers have been changed owing to DMA
transfer as explained here even when the program is stopped.
DMA0 transfer counter register .... TCR0
DMA1 transfer counter register .... TCR01
DMA0 control register .................. DM0CON
DMA1 control register .................. DM1CON
Note on Referencing and Setting the Work Area:
• The work area given below is assigned as the initial setting at the time of starting up the emulator
debugger. (Set by "F/W and Work Area" tab*1 in the Init dialog.)
When using the pod probe M30220T-PRB for M30220 and M30221 Group MCUs, use the initial
setting value.
02C0016 to 02C0F16: Work area
*1: Supported by emulator debugger M3T-PD30 Ver.4.00 or later
Notes on MAP References and Settings:
• When starting up the M30200T-RPD-E, the initial MAP settings are as follows.
0000016 to 003FF16: EXT
0040016 to FFFFF16: INT
• Always set the SFR area to EXT (external).
( 7 / 36 )
IMPORTANT
Note on Reading Out SFR Area:
• When reading out the registers below, they are not read out properly. However, they can be written
properly.
Pullup control register 2
Key input mode register
( 8 / 36 )
Chapter 2. Preparation
This chapter describes the package components, the system configuration and the preparation for using this product for the
first time.
2.1 Package Components..................................................................................................................10
2.2 Other Tool Products Required for Development........................................................................10
2.3 System Configuration.................................................................................................................11
( 9 / 36 )
Chapter 2. Preparation
2.1 Package Components
This product consists of the following items. When unpacking, check to see if your product package
contains all of these items.
Package components
Item
M30220T-PRB pod probe for M30220 and M30221 Group MCUs
FLX-144NSD converter board for 144-pin LQFP (144P6Q-A)
Screws for securing pod probe
M30220T-PRB User's Manual (this manual)
M30220T-PRB User's Manual (Japanese)
M30220T-PRB Repair Request Sheet (English)
M30220T-PRB Repair Request Sheet (Japanese)
Please keep the M30220T-PRB’s packing box and cushion material in your place for reuse at a later
time when sending your product for repair or other purposes. Always use these packing box and
cushion material when transporting the M30220T-PRB.
If any of these items are missing or found faulty, please contact your local distributor. Also, if there
is any question or doubt about the packaged product, contact your local distributor.
2.2 Other Tool Products Required for Development
To bring forward programs development on the M30220 and M30221 Group MCUs, the products
listed below are necessary in addition to those contained package above. Get them separately.
Quantity
1
1
2
1
1
1
1
Other tool products
Emulator main unit
Emulation pod main unit
Emulator debugger
Converter board
PC4701M, PC4701HS or PC4701L (essential)
M30200T-RPD-E (essential)
M3T-PD30 Ver.4.00 or later recommended (essential)
For 144-pin TQFP (144PFB-A): FLX-144NSE
(Converter board supporting the foot pattern of the target system)
For 120-pin LQFP (120P6R-A): FLX-120NSE
(Converter board supporting the foot pattern of the target system)
To purchase these products, contact your nearest distributer.
( 10 / 36 )
2.3 System Configuration
Figure 2.1 System configuration
Products (1) and (2) shown in Figure 2.1 are included with this product. Get (3) and (4) in Figure 2.1
separately.
(1) Pod probe (M30220T-PRB)
This pod probe is equipped with the evaluation MCUs M30220GP-EVA and M30220GP-PORT.
(2) Pitch converter board for 144-pin 0.5mm-pitch LQFP (FLX-144NSD)
Board for connecting the pod probe to the 144-pin 0.5mm-pitch LQFP foot pattern on the target
system.
(3) Pitch converter board for 144-pin 0.4mm-pitch TQFP (FLX-144NSE)
Board for connecting the pod probe to the foot pattern for 144-pin 0.4mm-pitch TQFP on the
target system.
(4) Pitch converter board for 120-pin 0.4mm-pitch LQFP (FLX-120NSE)
Board for connecting the pod probe to the foot pattern for 120-pin 0.4mm-pitch LQFP on the
target system.
For details on the connection, refer to "3.4 Connecting the Target System" (page 17).
( 11 / 36 )
Loading...