Renesas M306NKT-EPB, M16C/6NL, M16C/6N4, M16C/6N5, M16C/6NN, M16C/6N User Manual

Loading...

REJ10J0519-0200(T)

M306NKT-EPB

User’s Manual

Emulation Probe for M16C/6N Group M16C/6N4, 6N5, 6NK, 6NL, 6NM, 6NN

Rev.2.00

Oct. 16, 2006

Keep safety first in your circuit designs!

1.Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.

Notes regarding these materials

1.These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.

2.Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.

3.All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein.

The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.

Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http:// www.renesas.com).

4.When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.

5.Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.

6.The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.

7.If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.

Any diversion or reexport contrary to the export control laws and regulations of Japan and/ or the country of destination is prohibited.

8.Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.

M306NKT-EPB User’s Manual

Preface

Preface

The M306NKT-EPB is an emulation probe for The M16C/6N Group M16C/6N4, M16C/6N5, M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN. The M306NKT-EPB is used by connecting to the PC7501 emulator main unit.

This user's manual mainly describes specifications of the M306NKT-EPB emulation probe and how to setup it. For details on the emulator main unit and emulator debugger which are used with the M306NKT-EPB, refer to each product's user's manual.

All the components of this product are shown in "1.1 Package Components" (page 13). If there is any question or doubt about this product, contact your local distributor.

The related manuals for using this product are listed below. You can download the latest manuals from the Renesas Tools homepage (http://www.renesas.com/en/tools).

Related manuals

Item

Manual

Emulator main unit

PC7501 User’s Manual

Integrated development environment

High-performance Embedded Workshop User’s Manual

Emulator debugger

M16C R8C PC7501 Emulator Debugger User’s Manual

 

M3T-PD30F User’s Manual

C compiler

C compiler package for R8C/Tiny, M16C/60, 30, Tiny, 20 and 10 Series

 

C Compiler User's Manual

Assembler

C compiler package for R8C/Tiny, M16C/60, 30, Tiny, 20 and 10 Series

 

Assembler User's Manual

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 3 of 104

 

M306NKT-EPB User’s manual

Important

Important

Before using this product, be sure to read this user’s manual carefully.

Keep this user’s manual, and refer to this when you have questions about this product.

Emulator:

The emulator in this document refers to the following products that are manufactured by Renesas Technology Corp.:

(1)PC7501 main unit

(2)Emulation probe

(3)Package converter board for connecting the user system

The emulator herein does not include the customer’s user system and host machine.

Purpose of use of the emulator:

This emulator is a device to support the development of a system that uses the M16C Family M16C/60 Series M16C/6N Group M16C/6N4, M16C/6N5, M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN of Renesas 16-bit single-chip MCUs. It provides support for system development in both software and hardware.

Be sure to use this emulator correctly according to said purpose of use. Please avoid using this emulator for other than its intended purpose of use.

For those who use this emulator:

This emulator can only be used by those who have carefully read the user’s manual and know how to use it. Use of this emulator requires the basic knowledge of electric circuits, logical circuits, and MCUs.

When using the emulator:

(1)This product is a development supporting unit for use in your program development and evaluation stages. In massproducing your program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing integration test, evaluation, or some experiment else.

(2)In no event shall Renesas Solutions Corp. be liable for any consequence arising from the use of this product.

(3)Renesas Solutions Corp. strives to renovate or provide a workaround for product malfunction at some charge or without charge. However, this does not necessarily mean that Renesas Solutions Corp. guarantees the renovation or the provision under any circumstances.

(4)This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan.

(5)Renesas Solutions Corp. cannot predict all possible situations or possible cases of misuse where a potential danger exists. Therefore, the warnings written in this user’s manual and the warning labels attached to this emulator do not necessarily cover all of such possible situations or cases. Please be sure to use this emulator correctly and safely on your own responsibility.

(6)This product is not qualified under UL or other safety standards and IEC or other industry standards. This fact must be taken into account when taking this product from Japan to some other country.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 4 of 104

 

M306NKT-EPB User’s manual

Important

Usage restrictions:

This emulator has been developed as a means of supporting system development by users. Therefore, do not use it as a device used for equipment-embedded applications. Also, do not use it for developing the systems or equipment used for the following purposes either:

(1)Transportation and vehicular

(2)Medical (equipment where human life is concerned)

(3)Aerospace

(4)Nuclear power control

(5)Undersea repeater

If you are considering the use of this emulator for one of the above purposes, please be sure to consult your local distributor.

About product changes:

We are constantly making efforts to improve the design and performance of this emulator. Therefore, the specification or design of this emulator or its user’s manual may be changed without prior notice.

About the rights:

(1)We assume no responsibility for any damage or infringement on patent rights or any other rights arising from the use of any information, products or circuits presented in this user’s manual.

(2)The information or data in this user’s manual does not implicitly or otherwise grant a license for patent rights or any other rights belonging to us or third parties.

(3)This user’s manual and this emulator are copyrighted, with all rights reserved by us. This user’s manual may not be copied, duplicated or reproduced, in whole or part, without prior written consent of us.

About diagrams:

The diagrams in this user’s manual may not all represent exactly the actual object.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 5 of 104

 

M306NKT-EPB User’s Manual

Precautions for safety

Precautions for Safety

Definitions of Signal Words

In both the user’s manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties.

This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product.

DANGER

WARNING

CAUTION

CAUTION

IMPORTANT

This symbol represents a warning about safety. It is used to arouse caution about a potential danger that will possibly inflict an injury on persons. To avoid a possible injury or death, please be sure to observe the safety message that follows this symbol.

DANGER indicates an imminently dangerous situation that will cause death or heavy wound unless it is avoided. However, there are no instances of such danger for the product presented in this user's manual.

WARNING indicates a potentially dangerous situation that will cause death or heavy wound unless it is avoided.

CAUTION indicates a potentially dangerous situation that will cause a slight injury or a medium-degree injury unless it is avoided.

CAUTION with no safety warning symbols attached indicates a potentially dangerous situation that will cause property damage unless it is avoided.

This is used in operation procedures or explanatory descriptions to convey exceptional conditions or cautions to the user.

In addition to the five above, the following are also used as appropriate.

means WARNING or CAUTION.

Example:

CAUTION AGAINST AN ELECTRIC SHOCK

 

means PROHIBITION.

Example:

DISASSEMBLY PROHIBITED

 

means A FORCIBLE ACTION.

Example:

UNPLUG THE POWER CABLE FROM THE RECEPTACLE.

 

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 6 of 104

 

M306NKT-EPB User’s Manual

Precautions for safety

WARNING

Warnings for AC Power Supply:

zIf the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire.

zUse an AC power cable which complies with the safety standard of the country.

zDo not touch the plug of the AC power cable when your hands are wet. This may cause electric shock.

zThis product is connected signal ground with frame ground. If your developing product is transformless (not having isolation transformer of AC power), this may cause electric shock. Also, this may give an unrepairable damage to this product and your developing one.

While developing, connect AC power of the product to commercial power through isolation transformer in order to avoid these dangers.

zIf other equipment is connected to the same branch circuit, care should be taken not to overload the circuit.

zWhen installing this equipment, insure that a reliable ground connection is maintained.

zIf you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet.

Do not use this as it is because of the danger of electric shock and/or fire. In this case, contact your local distributor.

zBefore setting up this emulator and connecting it to other devices, turn off power or remove a power cable to prevent injury or product damage.

Warnings to Be Taken for This Product:

zDo not disassemble or modify this product. Personal injury due to electric shock may occur if this product is disassembled and modified. Disassembling and modifying the product will void your warranty.

zMake sure nothing falls into the cooling fan on the top panel, especially liquids, metal objects, or anything combustible.

Warning for Installation:

zDo not set this product in water or areas of high humidity. Make sure that the product does not get wet. Spilling water or some other liquid into the product may cause unrepairable damage.

Warning for Use Environment:

zThis equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care should be taken that this temperature is not exceeded.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 7 of 104

 

M306NKT-EPB User’s Manual

Precautions for safety

CAUTION

Cautions to Be Taken for Turning On the Power:

zTurn ON/OFF the power of the emulator and user system as simultaneously as possible.

zDo not leave either the emulator or user system powered on, because of leakage current the internal circuits may be damaged.

zWhen turning on the power again after shutting off the power, wait about 10 seconds.

Cautions to Be Taken for Handling This Product:

zUse caution when handling the main unit. Be careful not to apply a mechanical shock.

zDo not touch the connector pins of the emulator main unit and the target MCU connector pins directly. Static electricity may damage the internal circuits.

zDo not pull this emulator by the communications interface cable or the flexible cable. And, excessive flexing or force may break conductors.

zDo not flex the flexible cable for connecting to the emulator main unit and emulation probe excessively. The cable may cause a break.

zDo not use inch-size screws for this equipment. The screws used in this equipment are all ISO (meter-size) type screws. When replacing screws, use same type screws as equipped before.

Caution to Be Taken for System Malfunctions:

zIf the emulator malfunctions because of interference like external noise, do the following to remedy the trouble.

(1)Press the RESET button on the PC7501’s front panel.

(2)If normal operation is not restored after step (1), shut OFF the emulator once and then reactivate it.

Caution to Be Taken for External Trigger Input Voltage:

zKeep an external trigger input voltage of the emulator main unit less than a Vcc2 voltage. Overvoltage may cause damage to the internal circuits.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 8 of 104

 

M306NKT-EPB User’s Manual

Contents

Contents

 

 

 

Page

Preface

..........................................................................................................................................................................

3

Important.......................................................................................................................................................................

4

Precautions ..................................................................................................................................................for Safety

6

Contents........................................................................................................................................................................

9

User Registration ........................................................................................................................................................

11

Terminology ................................................................................................................................................................

12

1. Outline.....................................................................................................................................................................

13

1.1 ...................................................................................................................................

Package Components

13

1.2 ...........................................................................................

Other Tool Products Required for Development

14

1.3 ....................................................................................................................................

System Configuration

15

..........................................................................................................................

1.3.1 System Configuration

15

..................................................................

1.3.2 Names and Functions of the PC7501 Upper Panel LEDs

16

1.4 ................................................................................................................................................

Specifications

18

1.5 ..................................................................................................................................

Operating Environment

20

2. Setup.......................................................................................................................................................................

21

2.1 ..........................................................................................................

Flowchart of Starting Up the Emulator

21

2.2 ..............................................

Installing the Emulator Debugger (M16C R8C PC7501 Emulator Debugger)

22

........................................................................................................

2.2.1 Installing the Emulator Debugger

22

2.3 .......................................................................................................................

Connecting the Host Machine

23

2.4 ................................................................................................................................

Connecting the PC7501

24

2.5 ............................................................................................

Connecting the Power Supply for the Emulator

25

2.6 ...................................................................................................................................

Turning ON the Power

26

............................................................................

2.6.1 Checking the Connections of the Emulator System

26

................................................................................................................

2.6.2 Turning ON/OFF the Power

26

.........................................................................

2.6.3 LED Display When the Emulator Starts Up Normally

27

2.7 ..................................................................................................................................

Downloading Firmware

28

.....................................................................................

2.7.1 When It is Necessary to Download Firmware

28

....................................................................................

2.7.2 Downloading Firmware in Maintenance Mode

28

2.8 ......................................................................................................................................................

Self - check

29

..........................................................................................................................

2.8.1 Self - check Procedure

29

..............................................................................................

2.8.2 If an Error is Detected in the Self - check

30

2.9 .........................................................................................................................

Connecting the User System

31

..................................................................................................

2.9.1 Connecting to a 100 - pin LCC Socket

33

.............................................................

2.9.2 Connecting to a 100 - pin 0.65mm Pitch Foot Pattern (Part 1)

34

.............................................................

2.9.3 Connecting to a 100 - pin 0.65mm Pitch Foot Pattern (Part 2)

35

.............................................................

2.9.4 Connecting to a 100 - pin 0.65mm Pitch Foot Pattern (Part 3)

36

...............................................................

2.9.5 Connecting to a 100 - pin 0.5mm Pitch Foot Pattern (Part 1)

37

...............................................................

2.9.6 Connecting to a 100 - pin 0.5mm pitch Foot Pattern (Part 2)

38

............................................................................

2.9.7 Connecting to a 128 - pin 0.5mm pitch Foot Pattern

39

2.10 ............................................................................................................................................Switch Settings

40

..................................................................................................

2.10.1 A/D Conversion Bypass Capacitors

40

..................................................................................................................

2.10.2 Pullup of Emulation Ports

41

2.11 ................................................................................................................................Selecting Clock Supply

42

................................................................................................................................................

2.11.1 Clocks

42

.........................................................................................

2.11.2 Using an Internal Oscillator Circuit Board

42

...............................................................................

2.11.3 Using the Oscillator Circuit on the User System

46

..................................................................................................

2.11.4 Using the Internal Generator Circuit

46

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 9 of 104

 

M306NKT-EPB User’s Manual

Contents

 

 

Page

3. Usage (How to Use the Emulator Debugger) .........................................................................................................

47

3.1

Starting Up the Emulator Debugger ..............................................................................................................

47

 

3.1.1 INIT Dialog Box ...................................................................................................................................

47

 

3.1.2 MCU Setting Dialog Box .....................................................................................................................

53

 

3.1.3 Checking Connections of the Emulator System..................................................................................

56

3.2

Editor (Source) Window.................................................................................................................................

57

3.3

Program Execution ........................................................................................................................................

58

3.3

Hardware Breakpoint Setting Window...........................................................................................................

62

3.5

Trace Window................................................................................................................................................

66

3.6 RAM Monitor Window....................................................................................................................................

70

4. Hardware Specifications .........................................................................................................................................

71

4.1

Target MCU Specifications............................................................................................................................

71

4.2

Access Timing ...............................................................................................................................................

72

 

4.2.1 Operation Timing of Memory Expansion Mode and Microprocessor Mode (Vcc1=5V)......................

72

 

4.2.2 Operation Timing of Memory Expansion Mode and Microprocessor Mode (Vcc1=3V)......................

77

4.3

Differences between the Actual MCU and Emulator.....................................................................................

82

4.4

Connection Diagrams ....................................................................................................................................

85

4.5

External Dimensions......................................................................................................................................

87

 

4.5.1 External Dimensions of the Emulation Probe .....................................................................................

87

 

4.5.2 External Dimensions of the M30800T-PTC ........................................................................................

88

 

4.5.3 External Dimensions of the Converter Board M3T-F160-100NRB .....................................................

89

 

4.5.4 External Dimensions of the Converter Board M3T-F160-100NSD .....................................................

89

 

4.5.5 External Dimensions of the Converter Board M3T-F160-128NRD.....................................................

90

4.6

Notes on Using This Product.........................................................................................................................

91

5. Troubleshooting ......................................................................................................................................................

96

5.1

Flowchart to Remedy the Troubles ...............................................................................................................

96

5.2

When the Emulator Debugger Does Not Start Up Properly ..........................................................................

97

5.3

How to Request for Support ........................................................................................................................

100

6. Maintenance and Guarantee ................................................................................................................................

101

6.1

User Registration.........................................................................................................................................

101

6.2

Maintenance ................................................................................................................................................

101

6.3

Guarantee....................................................................................................................................................

101

6.4

Repair Provisions ........................................................................................................................................

101

6.5

How to Make Request for Repair ................................................................................................................

102

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 10 of 104

 

M306NKT-EPB User’s Manual

User Registration

User Registration

When you have purchased the emulator presented in this user's manual, please be sure to register it. As the H/W Tool Customer Registration Sheet is included with this manual, fill it in and FAX it to your local distributor or email the same contents to the following address. If you register it by email, you can use a text format for user registration created when installing the software in the following folder. Your registered information is used for only after-sale services, and not for any other purposes. Without user registration, you will not be able to receive maintenance services such as a notification of field changes or trouble information. So be sure to carry out the user registration.

For more information about user registration, please email to the following address.

regist_tool@renesas.com

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 11 of 104

 

M306NKT-EPB User’s Manual

Terminology

Terminology

Some specific words used in this user's manual are defined as follows:

Emulator system

This means an emulator system built around the PC7501 emulator. The PC7501 emulator system is configured with an emulator main unit, emulation probe, host machine and the integrated development environment High-performance Embedded Workshop.

Emulator main unit (Hereafter PC7501)

This means an emulator main unit for M16C Family.

Emulation probe

This means the emulation probe (this product) for the M16C/6N Group M16C/6N4, M16C/6N5, M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN MCUs.

Emulator debugger (M16C R8C PC7501 Emulator Debugger)

This means a software tool starting up from the High-performance Embedded Workshop to control the PC7501 and this product and enable debugging.

Renesas Integrated development environment High-performance Embedded Workshop

This tool provides powerful support for the development of embedded applications for Renesas microcomputers. It has an emulator debugger function allowing for the emulator to be controlled from the host machine via an interface. Furthermore, it permits a range of operations from editing a project to building and debugging it to be performed within the same application. What’s more, it supports version management.

Firmware

Program that analyzes contents of communication with the emulator debugger and controls the emulator hardware. This program is installed in the flash memory in the emulator main unit. This program is downloadable from the emulator debugger to upgrade the firmware or to support other MCUs.

Host machine

This means a personal computer used to control the PC7501 and emulation probe.

Software break

A software break is a function to break the program before the system executes an instruction at the specified address. The instruction at the preset address will not be executed.

Hardware break

A hardware break is a function to break the program when the system detects a write/read of data to/from memory or a leading/trailing edge of the signal entered from the external trace cable. The former break function is called address break; and the latter break function is called trigger break. While the instruction at the address where the software break is set is not executed, a hardware break is performed after the specified instruction is executed.

Target MCU

This means the MCU you are going to debug.

User system

This means a user's application system using the microcomputer to be debugged.

User program

This means the program you are going to debug.

Evaluation MCU

This means the MCU mounted on the emulation probe which is operated in the specific mode for tools.

#

In this user's manual, this symbol is used to show active Low. (e.g. RESET#: Reset signal)

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 12 of 104

 

M306NKT-EPB User’s Manual

1. Outline

1. Outline

This chapter describes the package components, the system configuration, the specifications of the emulator functions and the operating environment.

1.1 Package Components

The M306NKT-EPB package consists of the following items. When unpacking it, check to see if your M306NKT-EPB contains all of these items.

Table 1.1 Package components

Item

Quantity

M306NKT-EPB emulation probe

1

M30800T-PTC (pre-mounted) converter board for 100-pin 0.65mm pitch LCC

1

IC61-1004-051 100-pin 0.65mm pitch LCC socket made by Yamaichi Electronics Co., Ltd.

1

OSC-3 (16MHz) oscillator circuit board

1

OSC-2 oscillator circuit bare board

1

Network registers for ports P0--P5 pullup (51kΩ x 8)

6

H/W Tool Customer Registration Sheet (English)

1

H/W Tool Customer Registration Sheet (Japanese)

1

Repair Request Sheet (English)

1

Repair Request Sheet (Japanese)

1

M306NKT-EPB User’s Manual (this manual)

1

M306NKT-EPB User’s Manual (Japanese)

1

M306NKT-EPB Supplementary Document (English)

1

M306NKT-EPB Supplementary Document (Japanese)

1

*Please keep the M306NKT-EPB's packing box and cushion material in your place for reuse at a later time when sending your product for repair or other purposes. Always use these packing box and cushion material when transporting this product.

*If there is any question or doubt about the packaged product, contact your local distributor.

*For purchasing the IC61-1004-051 or for technical information, contact Yamaichi Electronics Co., Ltd.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 13 of 104

 

M306NKT-EPB User’s Manual

1. Outline

1.2 Other Tool Products Required for Development

To bring forward programs development on an M16C/6N Group M16C/6N4, M16C/6N5, M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN MCUs, the products listed below are necessary in addition to those contained package. Get them separately.

Table 1.2 Other tool products required for development

 

 

Product

Product name

 

Notes

Emulator main unit

 

PC7501

 

-

Emulator debugger

 

M16C R8C PC7501 Emulator debugger

Included with the PC7501

 

 

 

M3T-PD30F

 

 

 

 

 

 

 

100-pin 0.65mm pitch QFP

M3T-F160-100NRB

 

 

 

 

(PRQP0100JB-A,

M3T-100LCC-DMS

 

 

 

 

Previous code: 100P6S-A)

+

 

 

 

 

 

M3T-DIRECT100S

 

 

 

M16C/6N4

 

M3T-100LCC-DMS

 

 

 

 

+

 

 

boards

M16C/6N5

 

 

 

100-pin 0.5mm pitch LQFP

M3T-DUMMY100S

foot pattern of a user

 

 

 

 

Required

according to a

Converter

 

(PLQP0100KB-A,

M3T-F160-100NSD

system

 

 

 

 

 

 

 

 

100-pin 0.5mm pitch LQFP

 

 

 

 

 

Previous code: 100P6Q-A)

M3T-100LCC-QSD

Refer to

“2.9 Connecting

 

 

 

 

the User System” (page 31)

 

M16C/6NK

(PLQP0100KB-A,

M3T-F160-100NSD

 

 

 

 

 

 

 

 

Previous code: 100P6Q-A)

M3T-100LCC-QSD

 

 

 

M16C/6NL

 

 

 

 

 

 

 

M16C/6NM

 

 

 

 

 

128-pin 0.5mm pitch LQFP

 

 

 

 

M16C/6NN

(PLQP0128KB-A,

M3T-F160-128NRD

 

 

 

 

Previous code: 128P6Q-A)

 

 

 

* For purchasing these products, contact your local distributor.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 14 of 104

 

M306NKT-EPB User’s Manual

1. Outline

1.3 System Configuration

1.3.1 System Configuration

Figure 1.1 shows a configuration of the M306NKT-EPB system.

Host machine interface (LPT, USB or LAN)

(1) Emulation probe M306NKT-EPB

(4) Host machine

 

(3) Emulator

 

(2) Converter board

 

(5) User system

 

 

PC7501

 

M30800T–PTC

 

 

 

 

 

 

 

 

 

Figure 1.1 System configuration

(1)Emulation probe M306NKT-EPB (this product)

This is an emulation probe for the M16C/6N Group M16C/6N4, M16C/6N5, M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN and contains an evaluation MCU.

(2)Pitch converter board M30800T-PTC (included)

This is a pitch converter board for connecting to 100-pin 0.65mm pitch LCC socket IC61-1004-051 on the user system. For details, refer to "2.9 Connecting the User System" (page 31).

(3)Emulator main unit PC7501

The emulator main unit for the M16C Family to be used with this product.

(4)Host machine

A personal computer to control the emulator.

(5)User system

This is your application system.

This emulator cannot supply the power to the user system. Therefore design your system so that the user system is powered separately.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 15 of 104

 

M306NKT-EPB User’s Manual

1. Outline

1.3.2 Names and Functions of the PC7501 Upper Panel LEDs

Figure 1.2 shows the names of the LEDs on the upper panel of the emulator.

System status

Target status

LEDs

LEDs

Figure 1.2 Names of the LEDs on the upper panel of the PC7501

(1) System Status LEDs

The system status LEDs indicate the emulator PC7501's power supply, firmware operating status, etc. Table 1.3 lists the definition of each system status LED.

Table 1.3 Definitions of the system status LEDs

Name

Status

 

Meaning

POWER

ON

Emulator system power supply is turned ON.

 

OFF

Emulator system power supply is turned OFF.

SAFE

ON

Emulator system is operating normally.

 

Flashing

1.

The self-check is being executed.

 

 

2.

Downloaded firmware is being written into memory.

 

 

3.

If the ERROR LED is flashing on at the same time or alternately, it indicates that the

 

 

 

self-check error occurred.

 

OFF

PC7501 system is not operating normally.

ERROR

ON

PC7501 system is not operating normally (system status error).

 

Flashing

1.

Firmware is being downloaded.

 

 

2.

If the SAFE LED is flashing at the same time or alternately, it indicates that the self-

 

 

 

check error occurred.

 

OFF

PC7501 system is operating normally.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 16 of 104

 

M306NKT-EPB User’s Manual

1. Outline

(2) Target Status LEDs

The target status LEDs indicate operating status of the target MCU and power supply of the user system. Table 1.4 lists the definition of each target status LED.

Table 1.4 Definition of the target status LEDs

Name

Status

Meaning

POWER

ON

Power is supplied to the user system.

 

OFF

Power is not supplied to the user system.

CLOCK

ON

Clock is supplied to the target MCU.

 

OFF

Clock is not supplied to the target MCU.

RESET

ON

Target MCU is being reset, or reset signal of the user system is held low.

 

OFF

Target MCU is not being reset.

RUN

ON

User program is being executed.

 

OFF

User program has been halted.

WARNING

ON

Addresses 00000h and 00001h have been read out wrongly.

 

OFF

Addresses 00000h and 00001h have not been read out wrongly.

IMPORTANT

Note on Usage in Memory Expansion or Microprocessor Mode:

zWhen you use this product in memory expansion or microprocessor mode, be sure to design your system so that pins RDY# and HOLD# are not held low at startup. Otherwise, it cannot startup normally.

Note on the Target Status POWER LED:

zIf your MCU has two or more Vcc terminals, the LED does not light unless power is supplied to all the terminals.

Note on the Target Status CLOCK LED:

zCLOCK LED is turned off when both main and sub clocks are not oscillating. If either clock is oscillating, the LED is turned on.

zIf the LED is not turned on, check the following.

(1) After powering on the PC7501 (before starting up the emulator debugger):

Make sure that the oscillator circuit board is properly installed in the PC7501 and it is oscillating normally.

(2)After the emulator debugger is started up (after the Init dialog box settings are completed): Make sure that the oscillator selected in the Init dialog box is oscillating normally.

Note on Accessing Addresses 00000h and 00001h:

zWith the M16C/60 Series MCUs, when a maskable interrupt is generated, the interrupt data (interrupt number and interrupt request level) stored in addresses 00000h and 00001h are read out. Also, the interrupt request bit is cleared when address 00000h or 00001h is read out. Consequently, when the address 00000h or 00001h readout instruction is executed or when address 00000h or 00001h is read out in the cause of a program runaway, a malfunction occurs in that the interrupt is not executed despite the interrupt request, because the request bit of the highest priority interrupt factor enabled is cleared.

For this malfunction, when the reading out to address 00000h or 00001h is generated excluding the interrupt, the WARNING LED (yellow) of the PC7501’s upper panel lights up to alarm. When this LED lights, there is a possibility of wrong read access, therefore check the user program.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 17 of 104

 

M306NKT-EPB User’s Manual

1. Outline

1.4 Specifications

Tables 1.5 and 1.6 list the specifications of the M306NKT-EPB.

Table 1.5 Specifications of the M306NKT-EPB (1/2)

 

Applicable MCU

M16C/6N Group

 

 

M16C/6N4, M16C/6N5, M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN

Applicable MCU mode

Single-chip mode

 

 

Memory expansion mode

 

 

Microprocessor mode

 

Maximum operating frequency

24MHz (when using PLL)

 

Applicable power supply

3.0--5.5V

 

Emulation memory

(1) 512KB + 4KB for internal ROM of MCU

 

 

 

0F000h--0FFFFh, 80000h--FFFFFh,

 

 

 

maximum operating frequency: 24MHz, 0 wait

 

 

 

* When "Disable the Internal Flash ROM" is checked in the MCU tab of the

 

 

emulator debugger's MCU Setting dialog box, it is 10MHz.

 

 

(2) 31KB for internal RAM

 

 

 

00400h--07FFFh, maximum operating frequency: 24MHz, 0 wait

 

 

(3) CS3*--CS0* area (Possible to allocate by 4KB)

 

 

 

- Maximum operating frequency (at 5.0V) 0 wait:

7.0MHz

 

 

1 wait:

20.0MHz

 

 

2 wait, 3 wait:

24.0MHz

 

 

- Maximum operating frequency (at 3.0V) 0 wait:

6.0MHz

 

 

1 wait:

17.0MHz

 

 

2 wait, 3 wait:

24.0MHz

Clock oscillator

XIN-XOUT (1 to 16MHz):

 

 

Internal oscillator circuit board

 

 

Switchable to external oscillator input or internal generator circuit

 

 

XCIN-XCOUT (32.768kHz):

 

 

Internal oscillator circuit board

 

 

Switchable to external oscillator input

 

Basic debugging functions

-

Download

 

 

- Address match break (max. 8 points)

 

 

- Software break (max. 64 points)

 

 

- Program execution/stop (allows free-run execution supporting software breaks)

 

- Memory reference/setting (reference/setting C-variables, run-time execution)

 

-

Register reference/setting

 

 

-

Disassemble display

 

 

- C-level debugging, etc.

 

Real-time trace function

- 256K-cycle bus information recordable (Bus, external trigger, time stamp)

 

- 5 trace modes supported (Break/Before/About/After/Full)

 

 

- Can be recorded ON/OFF by events

 

Real-time RAM monitor function

- 4,096 bytes (256 bytes x16)

 

 

-

Data/last access result

 

Hardware break function

8 points (Execution address, bus detection, interrupt, external trigger signal)

Execution time measurement function

Time between program start and stop

 

 

Maximum/minimum/average execution time and pass count of specified four zones.

 

Count clock: Equal to MCU Clock or 16MHz

 

C0 coverage

8,192KB (256KB x 32 blocks)

 

External trigger input/event output

External trigger input (MCU-dependent-voltage CMOS level x8) or event output

 

(break x1, event x7)

 

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 18 of 104

 

M306NKT-EPB User’s Manual

 

 

 

1. Outline

Table 1.6 Specifications of the M306NKT-EPB (2/2)

 

 

Host machine interface

- LPT parallel (ECP, EPP, Byte/compatibility and Nibble/compatibility modes)

 

- USB (USB 1.1, full-speed) *1

 

- LAN (10BASE-T)

 

Power supply to emulator

Supplied from included AC adapter (power supply voltage: 100--240V, 50/60Hz)

Operating temperature

5 to 35°C (no dew)

 

 

Storage temperature

-10 to 60°C (no dew)

 

Power supply to emulation probe

Supplied from the DC power supply of the emulator main unit

Connection to user system

 

 

For 100-pin 0.65mm pitch LCC:

(see 2.9 "Connecting the User

 

 

M30800T-PTC (included)

System" on page 31)

 

 

For 100-pin 0.65mm pitch QFP (PRQP0100JB-A):

 

 

 

(1)

M3T-F160-100NRB (not included)

 

 

 

(2)

M30800T-PTC (included)

 

 

 

 

+ M3T-100LCC-DMS (not included)

 

M16C/6N4

 

 

+ M3T-DIRECT100S (not included)

 

M16C/6N5

 

(3)

M30800T-PTC (included)

 

 

 

 

+ M3T-100LCC-DMS (not included)

 

 

 

 

+ M3T-DUMMY100S (not included)

 

 

 

For 100-pin 0.5mm pitch LQFP (PLQP0100KB-A):

 

 

 

(1)

M3T-F160-100NSD (not included)

 

 

 

(2)

M30800T-PTC (included)

 

 

 

 

+ M3T-100LCC-QSD (not included)

 

M16C/6NK

 

For 100-pin 0.5mm pitch LQFP (PLQP0100KB-A):

 

 

(1)

M3T-F160-100NSD (not included)

 

M16C/6NL

 

(2)

M30800T-PTC (included)

 

M16C/6NM

 

 

+ M3T-100LCC-QSD (not included)

 

M16C/6NN

 

For 128-pin 0.5mm pitch LQFP (PLQP0128KB-A):

 

 

 

(1) M3T-FLX-128NRD (not included)

*1 Available to connect the host machine that supports USB 2.0.

 

With the USB interface, not all hardware (such as host machine, USB devices, USB hub) combination will work and

guaranteed.

 

 

 

 

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 19 of 104

 

M306NKT-EPB User’s Manual

1. Outline

1.5 Operating Environment

Be sure to use this emulator with the operating environmental of the emulator and host machine listed in Tables 1.7 and 1.8.

Table 1.7 Operating environmental conditions

Item

Description

Operating temperature

5 to 35°C (no dew)

Storage temperature

-10 to 60°C (no dew)

Table 1.8 Operating environment of the host machine

Item

Description

Host machine

IBM PC/AT compatibles

OS

Windows 98SE*

 

Windows Me

 

Windows XP

 

Windows 2000

CPU

Pentium III 600 MHz or more recommended

Memory

128 MB or more recommended

Pointing device such as mouse

Mouse or any other pointing device usable with the above OS that can be

 

connected to the main body of the host machine.

CD drive

Needed to install the emulator debugger and refer to the user’s manual

*Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 20 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2. Setup

This chapter describes the preparation for using this product, the procedure for starting up the emulator and how to change settings.

2.1 Flowchart of Starting Up the Emulator

The procedure for starting up the emulator is shown in Figure 2.1. For details, refer to each section hereafter. And, when the emulator does not start up normally, refer to “5. Troubleshooting” (page 96).

Check the package components.

User registration

Install the M16C R8C PC7501 emulator debugger.

Connect the host machine.

Connect the M306NKT-EPB to the emulator.

Connect the power supply for the emulator.

Connect the user system.

Turning on the power supply.

Check the LED display of the emulator.

Start up the emulator debugger from the High-performance Embedded Workshop.

Set the operating environment of the emulator debugger.

Refer to “1.1 Package Components” (page 13).

Refer to “User Registration” (page 11).

Install the M16C R8C PC7501 emulator debugger.

Connect the PC7501 to the host machine with the LPT parallel interface cable, USB interface cable or LAN interface cable.

Set the interface selection switch on the rear panel of the PC7501 to the using interface.

Connect the M306NKT-EPB and the M3T-FLX160-EPB of the

PC7501.

Connect a power supply for the emulator.

Connect the user system as occasion demands.

Turn ON the power to the emulator and the user system as simultaneously as possible.

Check that system status LEDs, and POWER, CLOCK, RESET and WARNING of target status LEDs are lighting. When the user system is not connected, the POWER LED does not light up.

Start up the High-performance Embedded Workshop, and start up the emulator debugger.

Set the INIT dialog box and MCU Setting dialog box of the emulator debugger.

Debug a program with various functions of the emulator debugger.

For how to use the High-performance Embedded Workshop and the emulator debugger, refer to each online manual.

Figure 2.1 Flowchart of starting up the emulator

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 21 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.2 Installing the Emulator Debugger (M16C R8C PC7501 Emulator Debugger)

If the OS used in your host machine is Windows XP or 2000, this installation must be executed by a user with administrator rights. Be aware that users without administrator rights cannot complete the installation.

Install the M16C R8C PC7501 emulator debugger following the procedure described below.

2.2.1 Installing the Emulator Debugger

(1)Downloading the M16C R8C PC7501 emulator debugger

Download the M16C R8C PC7501 emulator debugger from the URL below. http://download.renesas.com/eng/mpumcu/upgrades/in_circuit_emulators/pc7501/index.html

(2)Launching the installer

Start the “setup.exe” program.

(3)Entering the user information

In the “user information” dialog box, enter the user information (contractor, section, contact address, and host machine). The supplied information will be turned into a format by which technical support will be provided by e-mail.

(4)Completing the installation

A dialog box will be displayed indicating that setup has been completed. It means that the installation you made is completed.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 22 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.3 Connecting the Host Machine

When connecting the emulator PC7501 to a host machine, you can choose your desired interface from LPT parallel interface, USB interface and LAN interface. Use the interface selection switch on the emulator PC7501's rear panel to specify your desired interface. Figure 2.2 shows the outline to connect each interface cable.

Figure 2.2 Outline for interface cable connections

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 23 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.4 Connecting the PC7501

Figure 2.3 shows how to connect the PC7501 and the emulation probe.

M3T-FLX160-EPB

M306NKT-EPB

Figure 2.3 Connecting the PC7501 and emulation probe

CAUTION

Note on Connecting the PC7501:

zAlways shut OFF power before connecting the emulation probe. Otherwise, internal circuits may be damaged.

IMPORTANT

Notes on Connecting the PC7501:

zWhen connecting the emulation probe, be sure to hold the both sides of the emulation probe horizontally and insert it directly.

zThe connectors of the M306NKT-EPB are guaranteed for only 50 insertion/removal iterations.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 24 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.5 Connecting the Power Supply for the Emulator

The power is supplied from AC adapter to the emulator PC7501. Here following explains how to connect the AC adapter.

(1)Turn OFF the power to the PC7501.

(2)Connect the DC cable of the AC adapter to the PC7501.

(3)Connect the AC power cable to the AC adapter.

(4)Connect the AC power cable to the outlet.

CAUTION

Cautions for AC Adapter:

zUse only the AC adapter included in PC7501 package.

zThe included AC adapter is for PC7501. Do not use it for other products.

zBefore installing this equipment or connecting it to other equipment, disconnect the AC power cable from its outlet to prevent injury or accident.

zThe DC plug on the included AC adapter has the below polarity.

zThe included AC adapter has no power supply switch. The AC adapter is always active while connecting the AC power cable. Check if the power is supplied by the LED of the AC adapter.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 25 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.6 Turning ON the Power

2.6.1 Checking the Connections of the Emulator System

Before turning the power ON, check the connection of the interface cable with host machine, PC7501, emulation probe, and user system.

2.6.2 Turning ON/OFF the Power

Turn ON the power of the emulator and user system as simultaneously as possible. Turn OFF the power of the emulator and user system as simultaneously as possible.

Do not leave either the emulator or user system powered on, because of leakage current the internal circuits may be damaged. When turning ON the power again after shutting OFF the power, wait for about 10 seconds.

IMPORTANT

Notes on Power Supply:

zThe emulator's pin Vcc is connected to the user system in order to monitor user system voltage. For this reason, the emulator cannot supply power to the user system. Therefore, provide the user system with a separate power supply from that of the emulator.

zThe voltage of the user system should be as follows.

3.0V ≤ Vcc ≤ 5.5 V

zDo not change user system power supply voltage after power has been activated.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 26 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.6.3 LED Display When the Emulator Starts Up Normally

Figure 2.4 shows upper panel LED lighting status when the emulator started up properly. Check it when starting up the emulator system.

-If this LED does not light, check the voltage of the user system.

-Check that the power is supplied to all the power terminals.

-When the user system is not connected, this LED does not light.

POWER

POWER

: ON

SAFE

CLOCK

: OFF

ERROR

RESET

: Flashing

 

RUN

 

 

WARNING

 

SYSTEM

TARGET

 

STATUS

STATUS

 

LED display when the emulator starts up normally

Figure 2.4 LED display when the power turned on PC7501

IMPORTANT

Note on Memory Expansion or Microprocessor Mode:

zTo use memory expansion or microprocessor mode, be sure to set pins RDY#, HOLD# and NMI# so that they are not held low at startup. Otherwise the emulator system will not start up correctly.

Note on the Target Status POWER LED:

zIf your MCU has two or more Vcc terminals, the LED does not light unless power is supplied to all the terminals.

Note on the Target Status CLOCK LED:

zIf the LED is not turned on, check the following.

(1)After powering on the PC7501 (before starting up the emulator debugger):

Make sure that the oscillator circuit board is properly installed in the PC7501 and it is oscillating normally.

(2)After the emulator debugger is started up (after the Init dialog box settings are completed): Make sure that the oscillator selected in the Init dialog box is oscillating normally.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 27 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.7 Downloading Firmware

2.7.1 When It is Necessary to Download Firmware

It is necessary to download the firmware in the cases listed below. Normally, the following are automatically detected when the emulator debugger is started up, and the firmware is downloaded.

(1)When you use this product for the first time

(2)When the firmware has been upgraded

(3)When the emulator debugger has been upgraded

(4)When you use this product with a PC7501 which was used with another emulation probe before

If downloading firmware is not completed in the cases below, redownload the firmware.

-When the power is unexpectedly shut down during a download from the emulator debugger

-When a communications interface cable is unexpectedly pulled out

2.7.2 Downloading Firmware in Maintenance Mode

Download firmware in the special mode called maintenance mode as explained here following.

The user system must not be connected when you download the firmware.

(1)Set the interface select switch on the rear panel of the PC7501 to the LPT side and connect the LPT parallel interface cable to the PC7501 and the host machine.

(2)Within 2 seconds of activating power to the emulator, press the system reset switch on the PC7501 front panel to switch to maintenance mode. When the emulator is switched to maintenance mode, the System Status SAFE LED begins to flash.

(3)Start up the emulator debugger. When settings in the Init dialog box are complete, the dialog which urges to download the firmware will appear. Download firmware following messages. Required time for downloading the firmware is about 60 seconds.

POWER

POWER

POWER

POWER

POWER

POWER

SAFE

CLOCK

SAFE

CLOCK

SAFE

CLOCK

ERROR

RESET

ERROR

RESET

ERROR

RESET

 

RUN

 

RUN

 

RUN

 

WARNING

 

WARNING

 

WARNING

SYSTEM

TARGET

SYSTEM

TARGET

SYSTEM

TARGET

STATUS

STATUS

STATUS

STATUS

STATUS

STATUS

 

 

Maintenance mode started

Downloading firmware

POWER

POWER

POWER

POWER

: ON

 

SAFE

CLOCK

SAFE

CLOCK

: OFF

 

ERROR

RESET

ERROR

RESET

: Flashing

 

 

RUN

 

RUN

 

 

 

WARNING

 

WARNING

 

 

SYSTEM

TARGET

SYSTEM

TARGET

 

 

STATUS

STATUS

STATUS

STATUS

 

 

Download completed

Figure 2.5 LEDs during firmware download in maintenance mode

IMPORTANT

Note on Downloading Firmware:

zDo not shut OFF power while firmware is being downloaded. Doing so, the emulator will not start up properly. If power is shut off by mistake, redownload the firmware in maintenance mode.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 28 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.8 Self-check

2.8.1 Self-check Procedure

The self-check is a function to check the memory etc. mounted in the emulator. To run the self-check of the emulator, do so as explained here below. While the self-check is in progress, the LEDs will change as shown in Figure 2.6. In case of ERRORs 1 to 4, because the target status LEDs will change depending on errors, check the system status LEDs.

(1)If the user system is connected, disconnect it.

(2)Set the switches as the factory-settings to execute the self-check (see Table 2.1).

(3)Within 2 seconds of activating power to the emulator, press the system reset switch on the PC7501’s front panel.

(4)Check the "SAFE" LED starts flashing and then press the system reset switch again.

(5)The self-check will start. If the normal result is displayed in about 30 seconds, the self-check terminated normally.

POWER

POWER

POWER

POWER

: ON

SAFE

CLOCK

SAFE

CLOCK

: OFF

ERROR

RESET

ERROR

RESET

: Flashing

 

RUN

 

RUN

 

 

WARNING

 

WARNING

 

SYSTEM TARGET

STATUS STATUS

Maintenance mode started

ERROR 1 SAFE and ERROR flash

SYSTEM

TARGET

 

STATUS

STATUS

 

Self-check terminated normally

POWER

POWER

 

SAFE

CLOCK

- When the firmware does not support the emulation probe

ERROR

RESET

- When the emulation probe is not connected properly

 

RUN

 

 

WARNING

 

SYSTEM

TARGET

 

 

STATUS

STATUS

 

 

Emulation probe and firmware do not match

 

POWER

POWER

 

 

SAFE

CLOCK

- When the PC7501 system is not working properly

ERROR 2

ERROR

RESET

 

 

RUN

 

SAFE flashes, and ERROR lights

 

 

 

WARNING

 

 

 

 

 

SYSTEM

TARGET

 

 

STATUS

STATUS

 

 

PC7501 system status error

 

 

POWER

POWER

 

 

SAFE

CLOCK

- When a clock is not supplied to the emulation probe

ERROR 3

ERROR

RESET

 

 

RUN

 

SAFE and ERROR light alternately

 

 

 

WARNING

 

 

 

 

 

SYSTEM

TARGET

 

 

STATUS

STATUS

 

 

Emulation probe initialization error

 

POWER

POWER

 

 

SAFE

CLOCK

- When the emulation probe is not working properly

ERROR 4

ERROR

RESET

 

 

RUN

 

SAFE goes out, and ERROR lights

 

 

 

WARNING

 

 

 

 

SYSTEM TARGET

STATUS STATUS

Emulation probe status error

Figure 2.6 LED displays in the self-check

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 29 of 104

 

M306NKT-EPB User’s Manual

2. Setup

2.8.2 If an Error is Detected in the Self-check

If the self-check does not result normally (ERROR 1 to ERROR 4 in Figure 2.6), check the following.

(1)Recheck the connection of the emulation probe and PC7501.

(2)Redownload the proper firmware.

IMPORTANT

Note on the Self-check:

zPerform the self-check while not connecting the user system.

zIf the self-check does not result normally (excluding user system errors), the emulation probe may be damaged. Then contact your local distributor.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 30 of 104

 

Renesas M306NKT-EPB, M16C/6NL, M16C/6N4, M16C/6N5, M16C/6NN, M16C/6N User Manual

M306NKT-EPB User’s Manual

2. Setup

2.9 Connecting the User System

Connect the emulation pod to the user system for M16C/6N4 or M16C/6N5, and for M16C/6NK, M16C/6NL, M16C/6NM and M16C/6NN as shown in Figures 2.7 and 2.8, respectively.

Emulation probe

100-pin

 

 

 

 

 

0.65mm pitch

 

0.5mm pitch

 

 

 

 

 

M 30800T - PTC

M 30800T - PTC

(included)

(included)

 

M3T -100 LCCDMS

 

(not included)

M3T - FLX100- T

M3T- FLX100-R

(not included)

(not included)

 

*1

 

 

 

 

 

 

 

 

 

 

M3T -F160- 100NRB

LCC socket

M3T -DIRECT100S

M3T -DUMMY100S

M3T - F160100NSD M3T-100LCC-QSD

100-pin QFP

100-pin LCC

100-pin QFP

100-pin QFP

100-pin LQFP

100-pin LQFP

(not included)

(included)

(not included)

(not included)

(not included)

(not included)

 

 

 

 

 

: No. 1 pin

 

 

 

 

*: These three items are available in one package .

Figure 2.7 Connecting the user system according to user system (for M16C/6N4 and M16C/6N5)

CAUTION

Note on Connecting the User System:

zTake care not to attach a converter board in a wrong direction. It may cause a fatal damage to the emulator and user system.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 31 of 104

 

M306NKT-EPB User’s Manual

2. Setup

Emulation probe

100-pin 0.5mm pitch

128-pin 0.5mm pitch

M30800T - PTC (included)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M3T -F160 - 100NSD

M3T-100LCC-QSD

M3T - F 160-128 NRD

100-pin LQFP

100-pin LQFP

128-pin LQFP

(not included)

(not included)

(not included)

 

 

 

●: No. 1 pin

 

 

 

Figure 2.8 Connecting the user system according to user system (for M16C/6NK, M16C/6NL, M16C/6NM and M16C/6NN)

CAUTION

Note on Connecting the User System:

zTake care not to attach a converter board in a wrong direction. It may cause a fatal damage to the emulator and user system.

REJ10J0519-0200 Rev.2.00 Oct. 16, 2006

 

Page 32 of 104

 

+ 72 hidden pages